水溶性ZnO量子点制备及其光学性质

利用3-巯丙基三乙氧基硅烷对ZnO进行表面修饰后沉积SiO2, 制备出水溶性SiO2包覆ZnO的量子点. 与直接采用正硅酸乙酯沉积包覆SiO2的ZnO量子点相比, 362 nm处的激子荧光发射峰的强度提高了将近4倍. 由于表面引入了巯基官能团, 量子点的水溶性明显提高, 稳定性增强, 即使在较高的盐浓度下也不会团聚. 通过改变条件, 制备出了发光波长在420 nm的蓝色荧光量子点.     

水稳定的镁掺杂ZnO量子点:一锅法合成及细胞成像应用

一锅法合成了镁掺杂的ZnO量子点,利用APTES对其进行表面包覆,并采用XRD、TEM、UV-Vis、PL和FTIR等对材料进行了表征。结果表明镁掺杂能明显增强荧光发光强度,在合适的掺杂浓度(30%)下其量子产率由11%增加到33%。通过APTES的表面包覆使镁掺杂的ZnO量子点具有良好的水溶性和荧光稳定性,可用于MCF-7细胞成像研究。     

水稳定的镁掺杂ZnO量子点:一锅法合成及细胞成像应用

一锅法合成了镁掺杂的ZnO量子点, 利用APTES对其进行表面包覆, 并采用XRD、TEM、UV-Vis、PL和FTIR等对材料进行了表征。结果表明镁掺杂能明显增强荧光发光强度, 在合适的掺杂浓度(30%)下其量子产率由11%增加到33%。通过APTES的表面包覆使镁掺杂的ZnO量子点具有良好的水溶性和荧光稳定性, 可用于MCF-7细胞成像研究。     

氨基化单分散量子点/二氧化硅核壳纳米粒子的制备及其细胞标记

通过反向微乳液法, 在油溶性量子点表面包裹二氧化硅外壳, 使油溶性量子点水溶性化, 再利用3-氨丙基三乙氧基硅烷(APTES)在已形成的二氧化硅纳米颗粒表面进行氨基化改性, 制备富含氨基的二氧化硅包裹的量子点荧光纳米球. 通过透射电子显微镜(TEM)、粒径分析、zeta电位检测、紫外-可见分光光度、荧光分光光度和红外光谱等手段对产品进行了表征. 结果表明, 所制备的二氧化硅量子点纳米球(45 nm)具有单分散性、水溶性好及光化学稳定性强等优点. 通过静电作用, 所制备的单分散氨基化二氧化硅量子点对肿瘤细胞表面膜电荷进行了初步标记显像.     

CdTe/CdSe核壳量子点的合成及其在指纹显现中的应用

以CdCl2和Te粉为原料,在水相中合成了CdTe量子点核;通过外延生长在CdTe量子点核上包覆一层CdSe量子点,得到具有良好荧光性能的CdTe/CdSe核壳量子点;采用X射线衍射仪、透射电镜、高分辨透射电镜分析了不同反应条件下合成的CdTe/CdSe核壳量子点的晶体结构和微观结构,并对其进行了荧光光谱等测试和指纹显现分析.结果表明,合成的CdTe和CdTe/CdSe量子点粒径在3～5nm之间,粒径分布窄,水分散性良好;可以通过控制反应时间和Te/Se比等得到在500～700nm显示荧光发射峰的CdTe/CdSe核壳量子点.此外,核壳CdTe/CdSe量子点可以有效地和指纹物质结合,可应用于对铝合金油潜指纹的鉴别.     

非水稀溶液中SiO2包覆ZnO量子点的制备及其发光特性研究

本文利用溶胶-凝胶法在非水稀溶液中制备出SiO₂包覆的ZnO量子点。通过紫外-可见吸收光谱(UV-Vis)和荧光光谱对合成量子点的发光特性进行了研究。结果表明，在n_SiO2:n_ZnO=1∶4的条件下，ZnO量子点的发光性能最佳。经过Brus公式计算，该量子点的平均半径在2.8 nm左右，稳定性显著提高。其荧光光谱在363 nm处有一强而窄的激子发射峰，在519 nm处有一个宽而弱的绿色发射峰。说明SiO₂对ZnO形成了有效包覆，明显减少了ZnO的表面缺陷。     

水溶性量子点标记狂犬病P蛋白单克隆抗体的研究

利用共价偶联的方式,在水溶性缩合剂1-乙基-(3-二甲基氨基丙基)碳二亚胺盐酸盐(EDC)和N-羟基硫代琥珀酰亚胺(Sulfo-NHS)促进作用下,将400 μL的2 g/L狂犬病P蛋白抗体与适量的聚丙烯酸修饰后的水溶性硫脲修饰ZnO掺Cd量子点进行共价偶联反应,经磷酸盐缓冲液(PBS,0.01 mol/L,pH 7.4)透析纯化得到目标偶联物,采用荧光发射光谱、生物质谱、酶联免疫法等对偶联物进行表征.结果表明:偶联后的量子点荧光最大发射波长红移了10 nm,荧光强度随着狂犬病P蛋白抗原浓度的增加而逐渐增强;量子点标记狂犬病P蛋白抗体后的分子离子峰在m/z 67580处,比狂犬病P蛋白抗体分子离子峰增大了1453.由此证实狂犬病P蛋白抗体成功偶联到水溶性量子点上,且结构未受破坏.     

葡萄糖酸碳量子点的合成及其光学性能的研究

以葡萄糖酸为碳源,采用微波法、热解法和水热溶液法合成了水溶性较好的蓝色荧光碳量子点。用透射电镜(TEM)观察其形貌,荧光光谱(FL)和紫外可见光谱(UV)探究其激发和发射光谱,用时间分辨光谱(TRF)测其荧光寿命值。微波和热解法制备的碳量子点粒径在2.5~7.5 nm之间,激发波长为360 nm,发射波长为450 nm,荧光发射依赖激发波长,有三个荧光寿命,表面状态不均一。水热法制备的碳量子点,粒径在3.0~8.5 nm之间,激发波长为350 nm,发射波长为430 nm,荧光发射不依赖激发波长,只有一个荧光寿命值,表面状态均一。水热法合成的碳量子点荧光量子产率高为6.01%,为进一步研究葡萄糖酸制备碳量子点提供参考。     

硅硼掺杂碳点的制备及其在血红蛋白传感中的应用

杂原子掺杂是提高碳点荧光性能的有效手段.本研究以柠檬酸(C6 H8 O7)、硼酸(H3 BO3)、3-氨丙基三乙氧基硅烷(APTES)为原料,采用微波法一步制备硅和硼掺杂的碳点(SiBCDs);在SiBCDs前驱体中加入聚丙烯酸钠(PAAS),微波法制备了水溶性好、量子产率高的PAAS-SiBCDs.采用X射线衍射(XRD)、X射线光电子能谱(XPS)及红外光谱(FT-IR)对制备的碳点进行了表征.SiBCDs粒径约4~8 nm,PAAS-SiBCDs平均粒径5.2 nm,两者最大激发波长和发射波长分别为350和445 nm,荧光量子产率(QY)分别为20.1%和34.6%.基于血红蛋白对PAAS-SiBCDs的荧光猝灭效应,建立了全血样品中血红蛋白(Hb)的检测方法,线性范围为0.21~5.22μmol/L,检出限为0.06μmol/L(S/N=3).     

柠檬酸稳定的水溶性CdSe和CdSe/CdS量子点的荧光特性

用柠檬酸(citrate)作为稳定剂合成了尺寸分布集中、荧光性质良好的水溶性CdSe量子点。通过调节合成温度可以调控CdSe量子点的尺寸及相应的最大荧光发射波长。当温度由20 ℃增加到95 ℃时,合成的CdSe量子点的平均尺寸由2.0 nm增加到3.2 nm,相应的荧光发射峰由500 nm红移到570 nm,展现出明显的量子尺寸效应。进一步制备了CdSe/CdS核壳量子点,其荧光量子产率比CdSe增加了5～10倍。系统地研究了S/Se物质的量的比对CdSe/CdS量子点荧光特性的影响,通过XPS证实了CdSe/CdS量子点中CdS壳层的存在。利用红外光谱和核磁共振波谱表征了柠檬酸分子中的羧基和羟基氧原子与CdSe量子点表面的Cd离子的配位作用,进而揭示了柠檬酸分子对水溶性CdSe量子点溶液的稳定作用。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.