亲水性炭黑-天然橡胶纳米复合材料的制备及性能

利用原位球磨法制备了聚苯乙烯磺酸钠表面修饰炭黑,粒径分析和离心沉降实验结果表明,改性炭黑在水中具有十分优异的分散稳定性。利用该改性炭黑通过胶乳混合法成功制备了亲水性炭黑-天然橡胶纳米复合材料。采用万能电子拉力机、扫描电子显微镜、结合橡胶含量分析和动态热机械分析等多种手段对该复合材料进行了测试和研究。结果表明,与未改性炭黑相比,改性炭黑在橡胶基体中的分散性明显改善,与基体的相互作用显著增强,材料的力学性能大幅提高,填料网络化程度明显减弱。     

一种新型硅藻土填充橡胶纳米复合材料研究

橡胶的填料问题一直是人们的研究热点,针对炭黑和白炭黑在橡胶生产中存在的污染问题,本文选用成分结构与白炭黑类似的硅藻土来填充各种橡胶。首先对硅藻土进行了改性,并对不同改性剂改性硅藻土用于填充橡胶进行了研究。结果表明2.5份偶联剂Si69的改性效果最佳。通过机械共混法制备了改性硅藻土/橡胶纳米复合材料,通过力学性能测试确定了比较适合硅藻土填充的橡胶是氟橡胶、三元乙丙橡胶和丙烯酸酯橡胶。绿色环保且价格低廉的硅藻土可以替代白炭黑增强填充氟橡胶、三元乙丙橡胶和丙烯酸酯橡胶。     

炭黑填充顺丁橡胶(BR)复合材料中多重相互作用的研究

通过溶液浸泡及高速离心的方法分离了填料与聚合物间的强弱相互作用,研究了炭黑填充BR复合材料中多重相互作用与炭黑含量的关系,基于不同结合橡胶含量与储能模量的关系,提出了该多重相互作用随炭黑含量的演变模型.结果表明,存在于炭黑凝胶Ⅰ中的玻璃化转变温度和结晶熔融峰在炭黑凝胶Ⅱ中均完全消失,该现象意味着炭黑凝胶Ⅰ中测得的玻璃化转变及结晶行为只是与炭黑形成弱相互作用的那部分分子链段的贡献.在选用玻璃化转变温度考察炭黑-橡胶相互作用时应综合考虑样品特性以及测试方法.当炭黑含量不高于50 phr时,结合橡胶Ⅱ的含量随炭黑含量的增多呈线性增大,结合橡胶Ⅲ的含量则受炭黑含量的显著影响.炭黑填充橡胶复合材料中的多重相互作用可通过重叠模型进行描述,当炭黑含量分别为25~30phr,50~55 phr以及70~80 phr时,填充复合材料体系中分别存在结合橡胶Ⅲ的重叠层,结合橡胶Ⅲ和结合橡胶Ⅱ的重叠层,以及结合橡胶II的重叠层.     

橡胶补强填料的研究进展

随着汽车行业的发展,在"安全、环保和节能"方面,对轮胎的性能提出了更高的要求,因此对轮胎原料—橡胶的补强研究越来越多。本文详细介绍了补强填料补强橡胶的机理、补强填料的分类及改性途径,概述了传统补强填料炭黑、白炭黑及炭黑/白炭黑双向填料的性能和研究现状,综述了新型补强填料硅酸盐类、碳酸盐类及其它常用新型种类和性能,指出新型填料拓展了橡胶补强技术和功能橡胶材料领域的研究思路,应加强橡胶补强填料的开发、补强机理探讨和拓展补强复合材料的表征和检测手段,以满足橡胶行业发展的需求。     

改性硅藻土/橡胶复合材料的结构与性能

通过力学性能、扫描电镜(SEM)、红外光谱(IR)、X射线电子能谱(XPS)和热重(TG)分析,探讨改性硅藻土适合橡胶种类及对橡胶结构及热稳定性的影响,并与炭黑及白炭黑进行了对比研究。结果显示:改性硅藻土对氟橡胶(FKM)、丙烯酸酯橡胶(ACM)、三元乙丙橡胶(EPDM)、天然橡胶(NR)以及氯丁橡胶(CR)有增强作用,相容性较好,其中对FKM改性效果最明显,与白炭黑相比,其拉伸强度、扯断伸长率和耐磨性分别提高了28%、17%和30%;EPDM的拉伸强度、扯断伸长率和耐磨性分别提高了11%、12%和14%。并且改性硅藻土能够改善FKM和EPDM的耐热性能。     

湿法改性石墨烯在制备橡胶复合材料中的应用

橡胶由于其高弹性、良好的生物相容性、耐化学腐蚀及长期使用的稳定性等优点,在众多领域已有一百多年的应用历史。一般来说,在生胶硫化之前需要加入增强填料、润滑剂、偶联剂和促进剂等各类添加剂,以达到使用要求的性能。其中增强填料起到提高橡胶强度、提高橡胶耐磨耐热性、延长橡胶使用寿命的作用。相比于炭黑或者二氧化硅这些传统增强填料,新兴纳米材料石墨烯由于其优异的性能,只需极少量便可使橡胶的性能显著增强。然而,石墨烯片层之间的范德华力严重的阻碍了其在高分子机体内的分散,其在橡胶基体的分散性直接决定了石墨烯对于橡胶材料的增强效果。近年来,越来越多的研究开始关注通过在溶液中的湿法改性,包括物理或化学的方法来改性石墨烯,促进它与橡胶二者界面的相互作用,提高石墨烯在橡胶基体中的分散效果。本文总结了近几年湿法改性石墨烯在制备石墨烯/橡胶复合材料方面的研究进展。     

炭黑N134在不同橡胶基体中的分散及其混炼工艺调控

以炭黑N134作为填料,对比了异戊橡胶、丁苯橡胶及仿生橡胶3种体系下混炼工艺对硫化胶性能的影响,并针对仿生橡胶体系炭黑分散度低的问题,对混炼工艺进一步优化,从而提高分散度和动静态性能.结果表明,在所研究的密炼时间范围内,随着密炼时间的延长,异戊橡胶体系和丁苯橡胶体系的分散等级由原本的1级左右提升至6级以上.但延长密炼时间并未明显提升仿生橡胶体系的炭黑分散度.针对该问题引入塑炼和包辊工艺,仿生橡胶炭黑分散性明显提高.随炭黑分散等级的增加, 3种橡胶体系的伸张疲劳性能均得到了较大改善.其中仿生橡胶生胶经塑炼后,门尼黏度和重均分子量均明显下降,表明塑炼对于增强胶料的加工性能有明显作用.相同炭黑混炼时间下,随着塑炼时间的延长,硫化胶佩恩效应也增强,这主要是由于炭黑分散程度的提高使得炭黑与橡胶基体的有效接触面积增加,进而在一定程度上增加了界面结合胶的含量.     

原位接枝炭黑/天然橡胶复合材料的制备及性能

采用原位固相接枝方法,使在高温和强剪切作用下降解的天然橡胶接枝到炭黑表面.通过对接枝前后炭黑填充天然橡胶的性能对比发现,原位接枝炭黑不但能提高天然橡胶的硫化速度,还能提高拉伸强度,定伸应力和撕裂强度等;动态力学性能的测试结果表明接枝炭黑填充的天然橡胶中接枝炭黑网络化程度较低,这些结果主要归因于接枝炭黑在橡胶基体中分散性的改善及炭黑与橡胶之间作用力的增加.     

木质素在橡胶中的应用研究进展

木质素是地球上最丰富的生物材料之一,其基本单元为9-碳苯酚丙烷(香豆醇、松柏醇和芥子醇),这些单元通过不同类型的键连接在一起形成一个多酚类芳香族聚合物。作为造纸工业的主要废弃物,木质素成本低廉,目前主要用作低附加值的燃料,其开发价值还没有得到充分利用。将木质素用于填充改性橡胶既经济又环保,其不仅有补强的效果,还有偶联、抗氧防老、阻燃的作用,可部分代替炭黑。本文将对木质素的改性、橡胶/木质素复合材料的制备方法及研究进展进行综述,并对橡胶/木质素复合材料研究的挑战和机遇进行了展望。     

改性纳米炭黑/聚氨酯复合物的制备及表征

利用有机硅偶联剂改性的纳米炭黑和聚氨酯制备了纳米炭黑/聚氨酯复合物. 采用红外光谱、透射电镜、流变学及力学性能等测试方法对纳米粒子及其聚氨酯复合物进行了表征. 红外光谱表明, 纳米粒子的存在使聚氨酯的氢键结构发生了改变. 适量改性纳米炭黑粒子明显提高了聚氨酯的拉伸强度和断裂伸长率等力学性能. 流变学测试结果表明, 溶液中改性纳米炭黑粒子与聚氨酯分子间存在明显的相互作用.     

Grafting of maleic anhydride onto carbon black surface via ultrasonic irradiation

The grafting of maleic anhydride onto carbon black surface based on the Diels–Alder addition via ultrasonic irradiation was investigated. Fourier transform infrared spectroscopy (FT‐IR) and thermogravimetric analysis (TGA) were used to determine the chemical structure of the resulting products. The anhydride ring in the modified products can be opened into two carboxylic groups. Accordingly, the carboxylated carbon black was analyzed quantitatively through acid‐based titration to determine the concentration of anhydride ring on the modified carbon black's surface. The grafted molecules amount calculated from the concentration of the anhydride ring was consistent with the results of TGA data. Comparison of zeta potential measurement demonstrated that there were more negative charges attached to the surface of carbon black after ultrasonic modification. TEM observations showed that the conglomeration degree of modified carbon black decreased more than that of initial carbon black. Copyright © 2008 John Wiley & Sons, Ltd.     

丙烯酸在炭黑表面接枝聚合研究

丙烯酸在炭黑表面接枝聚合研究吴壁耀，刘安华，邵兰英，蒋子铎（武汉化工学院精细化工系，武汉，４３００７３）关键词接技聚合，炭黑，Ｚｅｔａ电位，表面改性炭黑是由大量的原生粒子聚集而成的．该聚集体表面积大、表面又含有丰富的极性基因，故在炭黑／涂料树脂体系中...     

聚铬黑T修饰电极检测亚硝酸盐的研究

利用电化学聚合法将铬黑T修饰到玻碳电极表面,制得聚铬黑T修饰电极。该修饰电极对亚硝酸盐的电化学氧化具有明显的催化作用,这种催化作用主要是由于聚铬黑T薄膜与带负电荷的亚硝酸盐离子的静电相互作用,导致亚硝酸盐离子富集在电极表面/溶液界面,显著增强了亚硝酸盐的氧化电流。电子传输系数α为0.735。选用0.85V作为工作电压,对亚硝酸盐进行安培检测,在0.05μmol/L～1.0 mmol/L和1.0～20.0 mmol/L两个浓度范围内呈现良好的线性关系,检测限达到0.01μmol/L。且该修饰电极有良好的重现性和稳定性。将该修饰电极用于泡菜中亚硝酸盐的测定,获得了满意的结果。     

丙烯酰胺在炭黑表面接枝聚合研究

利用Ｃｅ＾４＋和羟甲基化炭黑组成的氧化还原引发体系，探讨了丙烯酰胺在炭黑表面的自由基水溶液接枝聚合机理。研究表明：单体浓度、硝酸浓度和铈盐用量直接影响丙烯酰胺在炭黑表面的接枝聚合，ＦＴＩ和ＴＥＭ分析证明：改性炭黑表面存在着聚丙烯酰胺。改性炭黑粒子的Ｚｅｔａ电位值与未改性炭黑粒子相同，但它与水组成的分散体具有极好的分散稳定性。     

Surface-modified carbon black for As(V) removal

This paper reports the results of the adsorption performance of As(V) removal by a commercial carbon black and its H2SO4-modified form in a single-ion situation. The influence of different process parameters and the physicochemical principles involved were studied in detail. Acid modification caused morphological changes in the virgin carbon black as evidenced by BET surface area measurements and SEM study. FTIR spectra showed the introduction of sulfonic acid group in the parent carbon due to H2SO4 treatment. TGA analysis revealed higher weight loss characteristics of the modified carbon, demonstrating the creation of functional groups. The point of zero charge (pH pzc) of the modified carbon black is highly acidic (3.5) compared to commercial carbon black (6.4). It directly infers the generation of acidic functional moieties in the carbon black. The adsorption experiments were carried out following batch equilibrium techniques. The kinetics and thermodynamics of adsorption were investigated to unveil the mechanism and nature of the adsorption process, respectively. The kinetic parameters of different models were calculated and discussed. The kinetics of adsorption can be expressed by a pseudo-second-order model and intraparticle diffusion was not the rate-determining step. Dependence of pH on adsorption showed maximum metal uptake in the range of 4-5 and inferred surface complexion as the principal mechanism of adsorption. The equilibrium adsorption data were modeled using Freundlich, Langmuir, and Dubinin-Kaganer-Radushkevich (DKR) isotherm equations and the corresponding isotherm parameters were calculated and discussed in detail.     

Carbon black-chitosan film-based electrochemical sensor for losartan

Journal of Solid State Electrochemistry - A novel electrochemical method for determination of losartan using a glassy carbon electrode modified with carbon black nanoparticles immobilized within a...     

多壁碳纳米管修饰碳黑微电极同时测定多巴胺和抗坏血酸

制备了多壁碳纳米管修饰碳黑微电极,研究了多巴胺(DA)和抗坏血酸(AA)在该修饰电极上的电化学行为.实验表明,在pH 7.0的PBS缓冲溶液中,该修饰电极对DA和从均具有显著的催化氧化作用,AA与DA的氧化电位分别为30 mV和280 mV(vs.SCE).利用二次导数线性扫描伏安法测定,DA与AA的线性范围分别为6.0×10-9～2.0×10-4 mol/L和2.0×10-7～1.0×10-3mol/L,检出限为2.0×10-9mol/L 和1.0×10-7mol/L.方法已用于人工合成样品的分析.     

Kinetics and mechanism of oxygen electroreduction in alkaline solutions on xc-72r carbon black modified by products of pyrolysis of cobalt 5,10,15,20-tetrakis(4-methoxyphenyl)porphyrin

Cathodic oxygen reduction on XC-72R carbon black modified by products of pyrolysis of cobalt 5,10,15,20-tetrakis(4-methoxyphenyl)porphyrin (CoTMPP) (XC-72M) was studied. When XC-72R carbon black is modified, new active centers (ACs) are formed on the surface of the carbon support, on which the direct reaction to OH^- occurs, as shown using the rotating ring-disk electrode technique. The process of oxygen reduction on nonmodified carbon black occurs via the serial path. At low polarizations, the dependence of potential on pH corresponds to the slope of ??30 mV both for the carbon material and modified carbon black. This value is close to the coefficient in the Nernst equation for H₂/HO ₂ ^? . The slow stage of oxygen reduction is the transfer of the first or second electron to the adsorbed molecule. Herewith, the difference in the kinetics and mechanism of oxygen reduction on XC-72R and XC-72M is related to a stronger adsorption interaction of oxygen and ACs on XC-72M. The {ie1113-1} value in the pH range of 12?C14.6 is ?15 to ?20 mV both for XC-72R and XC-72M. In the case of the second halfwave potential on XC-72R, it is ?50 to ?60 mV. The observed effects are explained by a change in the surface state of catalysts at an increase in adsorption of OH^? ions at an increase in pH.     

An Acetylcholinesterase Sensor Based on a Pillar[6]arene–Silver Nanoparticle Composite for the Determination of Drugs for the Treatment of Alzheimer’s Disease

Journal of Analytical Chemistry - We developed a voltammetric sensor based on a glassy carbon electrode modified with carbon black, pillar[6]arene, and silver nanoparticles for the determination of...     

Gas chromatographic analysis of water phenolic pollutants using acid-washed graphitised carbon black

Summary The fractionation of eleven phenols which may be contaminants in drinking water has been accomplished by using acid-washed graphitised carbon black modified with trimesic acid and PEG 20 M.