阵列波导光栅平坦化的研究

阵列波导光栅的平坦化在实际应用中有很重要的意义.本文系统地研究了阵列波导光栅的平坦化.在输入波导、输出波导、阵列波导输入端与输出端上分别引入了指数型锥形波导.通过改变锥形波导的形状和尺寸来实现平坦化的优化.本文首先从理论上论述了引入指数型锥形波导的输出光谱特性,给出了结构参量的关系表达式,阐明了输入波导处的锥形波导是影响输出光谱平坦化的主要因素,阵列波导和输出波导处的锥形波导对输出光谱的平坦化有一定的影响.其次采用数值模拟的方法模拟了输出光谱,优化了结构参量,总结出了指数型锥形波导对平坦化影响的趋势和规律.模拟结果显示,输出光谱1 dB带宽大于通道间隔的50%,插入损耗从5.2 dB减小到了4.0 dB,串扰小于-30 dB.最后,本文给出了实验结果,插入损耗减小了0.87 dB,串扰减小了3.67 dB,1 dB带宽增加0.1 nm,增加了54.7%.实验结果表明引入指数型锥形波导提高了阵列波导光栅器件的光谱性能.     

阵列波导光栅平坦化的研究

阵列波导光栅的平坦化在实际应用中有很重要的意义.本文系统地研究了阵列波导光栅的平坦化.在输入波导、输出波导、阵列波导输入端与输出端上分别引入了指数型锥形波导.通过改变锥形波导的形状和尺寸来实现平坦化的优化.本文首先从理论上论述了引入指数型锥形波导的输出光谱特性,给出了结构参量的关系表达式,阐明了输入波导处的锥形波导是影响输出光谱平坦化的主要因素,阵列波导和输出波导处的锥形波导对输出光谱的平坦化有一定的影响.其次采用数值模拟的方法模拟了输出光谱,优化了结构参量,总结出了指数型锥形波导对平坦化影响的趋势和规律.模拟结果显示,输出光谱1 dB带宽大于通道间隔的50％,插入损耗从5.2 dB减小到了4.0 dB,串扰小于-30 dB.最后,本文给出了实验结果,插入损耗减小了0.87 dB,串扰减小了3.67 dB,1 dB带宽增加0.1 nm,增加了54.7％.实验结果表明引入指数型锥形波导提高了阵列波导光栅器件的光谱性能.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550nm波长附近的40nm带宽范围内获得了约2.6dB的通带平坦度,在1 550nm通信波长处,器件的插入损耗低于10dB.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550 nm波长附近的40 nm带宽范围内获得了约2.6 dB的通带平坦度,在1 550 nm通信波长处,器件的插入损耗低于10 dB.     

AWG结构的优化设计

通过分析AWG中心波导倾角特性,优化焦点间距,提出了两个结构约束方程,得出了结构紧凑的AWG设计方法.根据这一方法,可以由一定损耗条件下的最小弯曲半径和接口参数—接口处输入/输出波导间距和最短直波导长度,优化并完全确定其它结构参数,从而得到最小面积的AWG波导结构.最后给出了优化设计实例.     

650 nm聚合物阵列波导光栅波分复用器设计

选择在可见光波段具有较低吸收损耗的聚甲基丙烯酸甲酯-甲基丙烯酸环氧丙酯 共聚物作为波导包层材料,使用双酚A型环氧树脂作为折射率调节剂,根据材料的折射率设计了单模波导截面尺寸;然后,采用束传播法优化设计出16信道阵列波导光栅(AWG)器件的版图结构。利用Optiwave软件模拟了AWG器件的光传输特性,结果显示,器件的信道间隔为0.845 01 nm,插入损耗小于14 dB,串扰小于-25 dB。     

单侧耦合16通道100GHz硅基二氧化硅阵列波导光栅的研制

介绍了一种新型单侧耦合16通道、100GHz通道间隔的硅基二氧化硅阵列波导光栅(AWG)。通过增加一个Y分支波导结构,将AWG的输入、输出波导等间距整齐排列,仅用一个光纤阵列(FA)就可以对AWG器件进行耦合封装。这种AWG的结构设计可有效地减小器件尺寸和增加波导结构的弯曲半径,可减少器件的抛光和耦合时间,可降低器件的成本。     

小尺寸低折射率差硅基二氧化硅阵列波导光栅

随着阵列波导光栅(Arrayed Waveguide Grating,AWG)型器件在光通信系统中的大规模应用,对低成本AWG芯片的需求越来越多.在各种降成本方案中,减小AWG芯片的尺寸是最有效的方法之一.本文介绍了一种新型小尺寸低折射率差硅基二氧化硅AWG的设计.在该AWG中,输入波导/输出波导与平板波导连接的部分制...     

低插入损耗阵列波导光栅的设计

研究了阵列波导光栅的插入损耗.针对损耗来源,讨论了各项损耗的研究方法.分析了结构参量对损耗的影响,讨论了降低损耗的设计思路.对结构参量进行优化,设计了8通道200 GHz间隔的阵列波导光栅,中心通道插入损耗为1.37 dB,低于目前商用器件的1/2.对阵列波导光栅的设计具有一定的指导意义.     

小尺寸低折射率差硅基二氧化硅阵列波导光栅

随着AWG型器件在光通信系统中的大规模应用,对低成本AWG芯片的需求越来越多。在各种降成本方案中,减小AWG芯片的尺寸是最有效的方法之一。本文介绍了一种新型小尺寸低折射率差硅基二氧化硅阵列波导光栅（AWG）的设计。在该AWG中,输入波导/输出波导与平板波导连接的部分制作成两侧为空气槽的高折射率差波导,所以在与输出平板波导连接处的相邻输出波导间距较小,这样可以在设计上缩短平板波导的长度、减少阵列波导的数量,实现较小的AWG芯片尺寸。该AWG的其它部分,如输入/输出波导与光纤耦合的部分、阵列波导光栅等均采用常规的低折射率波导工艺,所以就同时具有与常规的低折射率波导AWG相同的优点：如低耦合损耗、较好的串扰以及光学特性等。根据这个原理,设计了一种40通道100 GHz频率间隔的低折射率差硅基二氧化硅AWG,其芯片尺寸只有23.88 mm?10.5 mm,是传统相同材料制作的AWG尺寸的1/6。     

A concise design of 16 × 16 polymer AWG with low insertion loss and crosstalk

In this paper, a 16-channel arrayed waveguide grating multiplexer (AWG) has been designed using polymer materials with 1.5% refractive index difference. Certain important parameters are optimized using the coupling mode theory and Beam Propagation Method. The factors that affect the insertion loss and the crosstalk are analyzed in this paper. In our design we introduced the parabolic taper structure and evaluated the suitable number of the arrayed waveguide, obtaining a total insertion loss of 2.19 dB. For obtaining a low crosstalk we evaluate the pitches of adjacent input/output waveguides ΔX and arrayed waveguides d as different values. We chose the value of ΔX about 2.5 times of d by enlarging the pitches of adjacent input/output waveguides. The crosstalk of the designed AWG is lower than −40 dB.     

Low-Loss 256-Channel AWG Module with Monolithically Integrated Spot-Size Converters

We developed a compact fiber-pigtailed 256-channel AWG module with 1.5% △ waveguides.By monolithically integrating spot-size converters with input/output waveguides, we achieved a lowinsertion loss of 2.6-4.1 dB with a low background crosstalk of -40 dB.     

低插损平坦谱响应阵列波导光栅解复用器优化设计

通过在输入波导与输入平板波导之间加入一种模式转换结构,获得了一个具有平坦光谱响应,低插损,光谱响应对称的阵列波导光栅型波分复用器,该模式转换结构由一个与输入波导的输出端连接的第一锥形波导,一个与此锥形波导输出端连接的细直波导,一个与细直波导输出端连接的第二个锥形波导以及一个连接输入平板波导和第二个锥形波导的梯形波导组成,通过优化设计梯形波导和第二个锥形波导的形状可以获得较宽的1dB通带带宽和较低的插损,同时光谱响应具有非常好的平坦性,而且通过对第一个锥形波导和细直波导的优化设计,在不引入明显的额外插损的条件下,能大大减小由于输入波导的弯曲引入的光谱响应的不平坦.     

A novel asymmetric arrayed waveguide grating with different lengths of input/output slabs

A novel arrayed waveguide grating (AWG) with asymmetric configuration is proposed. In this configuration, the length of the output slab region, the width and the spacing of the output waveguides are unequal to the corresponding parts of the input ones. Compared to a conventional symmetric AWG, the asymmetric AWG proposed in this paper has a smaller size without degrading its performance The analytic method used in a conventional symmetric AWG is extended to the asymmetric AWG. A design example of an asymmetric AWG with low insertion loss, low channel crosstalk and wide bandwidth is presented.     

Fabrication of Triplexers Based on Flattop SOI AWG

A triplexer is fabricated based on SOI arrayed waveguide gratings （AWGs）. Three wavelengths of the triplexer operate at different diffraction orders of an arrayed waveguide grating. The signals of 1490nm and 1550nm, which are input from central input waveguide of an AWG, are demultiplexed and the signal of 131Onto, which is input from central output waveguide of an AWG, is uploaded. The tested results show that the downloaded and uploaded signals have fiat-top response. The insertion loss is 9 dB on chip, the nonadjacent crosstalk is less than -30 dB for 1490nm and 1301 nm, and is less than -25 dB for 1550nm, the 3dB bandwidth equates that of the input light source.     

一种有效提高薄膜滤光片型密集波分复用器器件性能的方法及其实验研究

对光梳状滤波器加薄膜滤光片型模块制作密集波分复用器(DWDM)的两种应用方案进行了研究,提出了一种提高插损一致性、信道隔离度及减小串扰的结构方案。对新结构方案与常规结构方案进行了理论分析及实验研究,结果表明新结构可将级联次级峰由大于-30dB降至-50dB以下。用16波50GHz的密集波分复用器件拼接进行的实验表明最终器件的插损减小0．869dB,插损一致性减小2．005dB,相邻信道隔离度提高1．004dB,非相邻信道隔离度提高42．903dB．总串扰提高1．68dB。该方案不仅可以应用到光梳状滤波器与薄膜滤光片型模块拼接高性能的超密集波分复用器件．同样也可适用于阵列波导光栅等类型的密集波分复用器件中以降低工艺难度,提高性能指标。     

Design and fabrication of wavelength tunable AWGs based on the thermo-optic effect

In this Letter, a 16 channel 200 GHz wavelength tunable arrayed waveguide grating(AWG) is designed and fabricated based on the silicon on insulator platform. Considering that the performance of the AWG, such as central wavelength and crosstalk, is sensitive to the dimension variation of waveguides, the error analysis of the AWG with width fluctuations is worked out using the transfer function method. A heater is designed to realize the wavelength tunability of the AWG based on the thermo-optic effect of silicon. The measured results show that the insertion loss of the AWG is about 6 d B, and the crosstalk is 7.5 d B. The wavelength tunability of 1.1 nm is achieved at 276 m W power consumption, and more wavelength shifts will gain at larger power consumption.     

Acrylic and metal based Y-branch plastic optical fiber splitter with optical NOA63 polymer waveguide taper region

We proposed a simple low-cost acrylic and metal-based Y-branch plastic optical fiber (POF) splitter which utilizes a low cost optical polymer glue NOA63 as the main waveguiding medium at the waveguide taper region. The device is composed of three sections: an input POF waveguide, a middle waveguide taper region and output POF waveguides. A desktop high speed CNC engraver is utilized to produce the mold inserts used for the optical devices. Short POF fibers are inserted into the engraved slots at the input and output ports. UV curable optical polymer glue NOA63 is injected into the waveguide taper region and cured. The assembling is completed when the top plate is positioned to enclose the device structure and connecting screws are secured. Both POF splitters have an average insertion loss of 7.8 dB, coupling ratio of 55: 45 and 57: 43 for the acrylic and metal-based splitters respectively. The devices have excess loss of 4.82 and 4.73 dB for the acrylic and metal-based splitters respectively.