Comparison of the performance of pyridine-functionalized nanoporous silica particles for the extraction of gold(III) from natural samples

We have developed a technique for the solid-phase extraction of gold using various kinds of pyridine-functionalized nanoporous silica prior to its determination in various samples using FAAS. The effects of solution pH, sample and eluent flow rate, sample volume and of potentially interfering ions are compared. The limits of detections vary from 28 to 53?pg?mL^?1. The accuracy and precision are between 99.8% and 98.3?% and 0.7 to 1.6?% (RSD), respectively. The method was successfully applied to several standard reference materials.

Separation and spectrophotometric determination of very low levels of Cr(VI) in water samples by novel pyridine-functionalized mesoporous silica

A modified SBA-15 mesoporous silica was developed, as an adsorbent, for the removal of Cr(VI) ions from natural-water samples. The effects of experimental parameters, including pH of solution, sample and eluent flow rate, the eluent composition, the eluent volume, and the effect of coexisting ions on the separation and determination of Cr(VI), were investigated. It was shown that Cr(VI) was selectively adsorbed from aqueous solution at pH 3, but Cr(III) could be adsorbed from solution at alkaline pH range. The retained Cr(VI) was eluted with 0.5?mol?L^?1 KCl solution in 0.1?mol?L^?1 Na₂CO₃ subsequently. Under the optimum conditions, the modified mesoporous silica (py-SBA-15) with a high pore diameter exhibited an adsorption capacity of 136?mg?g^?1 and a lower limit of detection than 2.3?µg?L^?1 by using diphenylcarbazide as a chromophorous reagent for the determination of Cr(VI) ions. A preconcentration factor as high as 200 was calculated for Cr(VI). The loaded py-SBA-15 can be reactivated with recovery of more than 98.5% over at least eight cycles. The relative standard deviation (RSD) for Cr(VI) ion recovery was less than 1.8%. Validation of the outlined method was performed by analysing a certified reference material (BCR 544). The proposed method was applied to determine Cr(VI) value in natural and waste water samples successfully.     

Solvent extraction of Au(III) for preparation of a carrier-free multitracer and an Au tracer from an Au target

Separation of Au(III) and various carrier-free radionuclides by solvent extraction was investigated using an Au target irradiated by an energetic heavy-ion beam. Percentage extraction of Au(III) and coextraction of the radionuclides were determined with varying parameters such as kinds of solvent, molarity of HCl or pH, and Au concentration. Under the conditions where Au(III) was effectively extracted, namely extraction with ethyl acetate or isobutyl methyl ketone from 3 mol·dm^–3 HCl, carrier-free radionuclides of many elements were found to be more or less coextracted. Coextraction of radionuclides of some elements was found to increase with an increase in the concentration of Au(III). This finding is ascribed to the formation of strong association of the complex of these elements with chloroauric acid. In order to avoid serious loss of these elements by the extraction, lowering of the Au(III) concentration or the use of a masking agent such as sodium citrate is necessary. Gold(III) was shown to be effectively back extracted with a 0.1 mol·dm^–3 aqueous solution of 2-amino-2-hydroxymethyl-1,3-propanediol. Thus, a radiochemical procedure has been established for preparing a carrier-free multitracer and an Au tracer with carrier form from an Au target irradiated with a heavy-ion beam. Both tracers are now used individually for chemical and biological experiments.     

Organo-Laponites as novel mesoporous supports for manganese(III) salen catalysts

A Mn(III) salen complex was immobilized onto the Laponite surface using three different methodologies: method A, direct immobilization of the complex on the parent Laponite; method B, covalent anchoring through cyanuric chloride (CC); and method C, covalent anchoring through CC into a 3-aminopropyl)triethoxysilane (APTES) modified Laponite. All of the materials were characterized by FTIR, XPS, thermogravimetry, XRD, and nitrogen isotherms at 77 K, to gather information on the modifications introduced by the organo spacers within the Laponite surface, as well as on the anchored complex integrity; the Mn based materials were screened in the heterogeneous epoxidation of styrene. The results have shown that the immobilization of the manganese(III) salen complex by methods B and C have occurred at the edges of the clay particles through the spacers (APTES and CC) that have been anchored onto the Si-OH groups, whereas in method A, the complex is distributed throughout the clay surface, including the interlayer region. Therefore, the manganese loadings on the Laponites were as follows: materials prepared by method A > method B > method C. All of the heterogeneous catalysts showed high styrene epoxide selectivity, with that prepared by method A showing comparable styrene epoxide selectivity as the homogeneous phase reaction. The styrene epoxide yields decrease in the following order: materials prepared by method A > method B > method C (1st cycles), which parallel the respective support catalytic activity and decreasing of manganese content. The heterogeneous catalysts prepared using methods B and C could be reused at least for four times, with the former exhibiting the most stable catalytic activity, but that prepared by method A showed a significant decrease after two catalytic cycles.     

Post-treatment and characterization of novel luminescent hybrid bimodal mesoporous silicas

A novel luminescent hybrid bimodal mesoporous silicas (LHBMS) were synthesized via grafting 1,8-Naphthalic anhydride into the pore channels of bimodal mesoporous silicas (BMMs) for the first time. The resulting samples were characterized by powder X-ray diffraction (XRD), N₂ adsorption/desorption measurement, Fourier transform infrared spectroscopy (FT-IR), Transmission electron microscopy (TEM), UV-vis absorption spectroscopy, and Photoluminescence spectroscopy (PL). The results show that 1,8-Naphthalic anhydride organic groups have been successfully introduced into the mesopores of the BMMs and the hybrid silicas are of bimodal mesoporous structure with the ordered small mesopores of around 3 nm and the large mesopores of uniform intra-nanoparticle. The excellent photoluminescent performance of LHBMS has a blue shift compared to that of 2-[3-(triethoxysilyl) propyl-1 H-Benz [de]isoquinoline-1, 3(2 H)-dione, suggesting the existence of the quantum confinement effectiveness.     

Near-infrared emission from novel Tris(8-hydroxyquinolinate)lanthanide(III) complexes-functionalized mesoporous SBA-15

A novel mesoporous material covalently bonded with 8-hydroxyquinoline (HQ) was synthesized (designated as Q-SBA-15). The 5-formyl-8-hydroxyquinoline grafted to (3-aminopropyl)triethoxysilane, that is, alkoxysilane modified 8-hydroxyquinoline (Q-Si), was used as one of the precursors for the preparation of the Q-SBA-15 material. On the basis of the other function of the Q-Si of coordinating to lanthanide (Ln) ions, for the first time, the LnQ 3 complexes (Ln = Er, Nd, Yb) have been covalently bonded to the SBA-15 materials. The derivative materials, denoted as LnQ 3-SBA-15, were characterized by field emission scanning electron microscopy (FE-SEM), powder X-ray diffraction (XRD), transmission electron microscopy (TEM), nitrogen adsorption-desorption, and fluorescence spectra. Upon excitation at the ligands absorption bands, all of these materials show the characteristic near-infrared (NIR) luminescence of the corresponding lanthanide ions through the intramolecular energy transfer from the ligands to the lanthanide ions. The NIR luminescence of these mesoporous materials was compared with that of the corresponding pure LnQ 3 complexes and discussed in detail.     

Solvent extraction of Au(III) using 2-mercaptobenzimidazole into n-butanol

A method has been developed for the extraction of Au(III) with 2-mercaptobenzimidazole into n-butanol.¹⁹⁹Au has been used as a tracer for establishing the ideal extraction parameters such as effect of pH, time of equilibration, solvents and anions. Separation factor and decontamination factor have also been evaluated to determine the selectivity of the method with respect to various elements. The interfering elements were suppressed by the use of suitable masking agents which increased the selectivity. The stoichiometry of metal to reagent was determined by the method of substoichiometric extraction and slope ratio method.     

Comparison of the performance of different modified graphene oxide nanosheets for the extraction of Pb(II) and Cd(II) from natural samples

Graphene nanosheets were modified with amino groups and the resulting material was used as a sorbent for the extraction of cadmium and lead ions. The nanosheets were characterized by IR spectroscopy, transmission electron microscopy, thermal gravimetric analysis and elemental analysis. The effects of sample pH, eluent parameters (type, concentration and volume of eluent), flow rates (of both sample and eluent), and of a variety of other ions on the efficiency of the extraction of Cd(II) and Pb(II) were optimized. Following solid phase extraction, the elements were determined by FAAS. The limits of detection are <0.9 μg L^?1 for Pb(II) and <5 ng L^?1 for Cd(II). The relative standard deviations are <2.2 %. The method was validated by analyzing several certified reference materials and was then used for Pb(II) and Cd(II) determination in natural waters and vegetables.

Selective extraction and determination of Au(III) by first-derivative spectrophotometry

The selective extraction of Au(III) in the presence of Zn(II) by salting-out of 2-propanol was investigated. The salting-out effect increased partitioning between water and 2-propanol in the presence of sodium chloride in aqueous–organic mixtures. This is observed through the distribution coefficient, which increases with salt addition. First-derivative spectrophotometry, which eliminates interference from overlapping spectral bands, was used for the determination of trace Au(III) in the presence of Zn(II). Absorption spectra were recorded and the first-derivative spectra were obtained using Δλ?=?10?nm. The calibration graph was linear for 0.857–5.142?µg?mL^?1 and the detection limit was 0.038–8?µg?mL^?1. The proposed method has been successfully applied to the determination of trace Au(III) in synthetic mixtures and Algerian low gold ore solutions. The results agree with those obtained by atomic absorption spectroscopy and the recoveries were >98%. The relative standard deviations were in all instances less than 3%.     

Recovery of Au(III) ions by Au(III)-imprinted hydrogel

A new Au(III)-imprinted hydrogel (Au(III)-Imp) was prepared by the photopolymerisation of 4-acryloylmorpholine (AcM), 2-hydroxyethyl acrylate (HEA), and poly(ethylene glycol) diacrylate (cross-linking monomer, PEG-DA) in the presence of gold ions. In addition, non-imprinted hydrogel (N-Imp) was similarly prepared without Au(III) ions The Au(III)-Imp hydrogel was characterised by several techniques. To achieve the optimal conditions, effect of pH, time, and initial metal ion concentrations were investigated using a batch system. The pre-concentration factor for Au(III) ions was found to be at least 100. The analytical parameters of the method were determined and the method was also successfully applied to computer circuit board scrap samples. The reusability of the Au(III)-Imp hydrogel was also determined.     

Study on sorption of U(VI) onto ordered mesoporous silicas

The mesoporous silicas (MCM-41 and MCM-48) are synthesized by hydrothermal method, which are characterized by XRD and BET techniques. The application of mesoporous silicas for the sorption of U(VI) from aqueous solution are studied by using batch technique under ambient condition. The effects of contact time, solid-to-liquid ratio (m/V), solution pH, ionic strength and temperature are determined, and the results indicate that the sorption of U(VI) to MCM-41 or MCM-48 are strongly dependent on pH values but independent of ionic strength. Compared with Langmuir model, the sorption isotherms can be simulated by Freundlich model well according to the high relative coefficients. The parameters for Langmuir and Freundlich sorption isotherms are calculated from the temperature at 298, 318 and 338 K, respectively, and the results suggest that the sorption of U(VI) on MCM-41 or MCM-48 is a spontaneous and exothermic process. In contrast to its sorption capacity for U(VI), MCM-48 is a suitable material for the preconcentration of U(VI) from large volumes of aqueous solutions.     

Selective solid-phase extraction of trace Fe(III) from biological and natural water samples using nanometer SiO2 modified with acetylsalicylic acid

A new method using acetylsalicylic acid (aspirin) modified SiO₂ nanoparticles (nanometer SiO₂-aspirin) as a solid-phase extractant (SPE) has been developed for the preconcentration of trace amounts of Fe(III) prior to their determination by inductively coupled plasma optical emission spectrometry. The preconcentration conditions of analytes were investigated, including the pH value, the shaking time, the mass of sorbent, the sample flow rate and volume, the elution condition and the interfering ions. At pH 4, the sorption capacity of nanometer SiO₂-aspirin was found to be 1.28 mmol g⁻¹. The preconcentration factor is 50. The detection limit (3σ) for Fe(III) was 0.49 ng mL⁻¹. The method was validated by analyzing two certified reference materials (GBW 08301, river sediment and GBW 08303, polluted farming soil), and the results obtained are in good agreement with standard values. The method was also applied to the determination of trace Fe(III) in biological and water samples with satisfactory results. Correspondence: Xiangbing Zhu, Department of Chemistry, Lanzhou University, Lanzhou 730000, P.R. China     

三价金配合物抗肿瘤活性研究*

三价金配合物具有潜在的抗肿瘤活性,是目前金属药物领域的研究热点。本文按配位原子的不同总结了稳定三价金配合物的结构特征,按其生物活性的构效关系、生物靶点和作用机制综述了三价金配合物抗肿瘤活性研究的最新成果：配体的结构特点以及离去基团对三价金配合物的体外细胞毒性影响较大;介绍了用于检测三价金配合物与可能的生物靶分子之间的相互作用的多种物理和生物学方法,重点关注了相互作用的模式,如嵌入/静电吸引/共价结合等,并解释了三价金配合物抗肿瘤活性的原因。最后提出了一些研究新思路,以期有助于设计得到靶标明确的具有良好药理活性的抗肿瘤药物。     

Chemically modified attapulgite with asparagine for selective solid-phase extraction and preconcentration of Fe(III) from environmental samples

A new method that utilizes asparagine modified attapulgite as a solid phase extractant has been developed for preconcentration of trace Fe(III) prior to the measurement by inductively coupled plasma optical emission spectrometry. Characterization of the surface modification was performed on the basis of Fourier transform infrared spectra. The separation/preconcentration conditions of the analyte were investigated, including the pH value, the shaking time, the sample ?ow rate and volume, the elution condition and the interfering ions. At pH 4, the new adsorbent had relatively high capacity and enrichment factor compared to other methods reported so far. The adsorbed Fe(III) was quantitatively eluted by 2 mL of 0.5 mol L⁻¹ HCl. Common coexisting ions did not interfere with the separation. The detection limit of the method was 0.19 μg L⁻¹. The relative standard deviation was 3.4% (n = 8) which indicated that the method had good precision for the analysis of trace Fe(III) in solution samples. The method was validated using two certified reference materials and has been applied for the determination of trace Fe(III) in biological and natural water samples with satisfactory results.     

Synthesis and efficiency of a chelating fiber for preconcentration and separation of trace Au(III) and Pd(IV) from solution samples

A novel poly(acryl-benzoylamidrazone-acryl-benzoylhydrazine) chelating fiber was synthesized simply from nitrilon (polyacrylonitrile fiber). The structure of the chelating fiber was verified with the help of FT-IR spectrum. The parameters influencing the efficiency of the fiber for concentrating trace amounts of Au(III) and Pd(IV) were investigated in detail. Trace Au(III) and Pd(IV) were enriched and separated from real sample solutions and detected using inductively coupled plasma atomic emission spectrometry (ICP-AES) with satisfactory results. The experiments show that the method is rapid, precise, simple and convenient to use.     

Solid-phase extraction of trace Cu(II) Fe(III) and Zn(II) with silica gel modified with curcumin from biological and natural water samples by ICP-OES

Silica gel was firstly functionalized with aminopropyltrimethoxysilane obtaining the aminopropylsilica gel (APSG). The APSG was reacted subsequently with curcumin yielding curcumin-bonded silica gel (curcumin-APSG). This new bonded silica gel was used for separation, pre-concentration and determination of Cu(II), Fe(III), Zn(II) in biological and natural water samples by inductively coupled plasma optical emission spectrometry (ICP-OES). Experimental conditions for effective adsorption of trace levels of metal ions were optimized with respect to different experimental parameters using batch and column procedures in detail. The optimum pH value for the separation of metal ions simultaneously on the newly sorbent was 4.0. Complete elution of the adsorbed metal ions from the sorbent surface was carried out using 2.0 mL of 0.1 mol L^− 1 of HCl. Common coexisting ions did not interfere with the separation and determination at pH 4.0. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 0.63, 0.46 and 0.37 mmol g^− 1 for Cu(II), Fe(III) and Zn(II) respectively. The time for 95% sorption for Cu(II) Fe(III) and Zn(II) was less than 2 min. The detection limits of the method defined by IUPAC was found to be 0.12, 0.15 and 0.40 ng mL^− 1 for Cu(II), Fe(III) and Zn(II), respectively. The relative standard deviation (RSD) of the method under optimum conditions was lower 3.0% (n = 5). The procedure was validated by analyzing the certified reference river sediment material (GBW 08301, China), the results obtained were in good agreement with standard values. This sorbent was successfully employed in the separation and pre-concentration of trace Cu(II), Fe(III) and Zn(II) from the biological and natural water samples yielding 75-fold concentration factor.     

Generation of gold thread from Au(III) and triethylamine

Gold threads were spontaneously generated at room temperature from a combined solution of aqueous HAuCl4 and triethylamine. Initially, some reduced gold nanoparticles were self-organized into one-dimensional (1D) nanowires, which then developed into three-dimensional (3D) microscale threads of gold. After aging, the self-organized gold thread grew spontaneously, accompanied by the generation of new buds to start new branches. TEM images show that the gold thread is composed of elastic materials; in which, colloidal gold nanoparticles reduced by triethylamine serve as the bricks, whereas elastic substances formed during the reaction serve as the mortar, which holds together the gold particles. The results of IR and 1H NMR spectroscopy demonstrate that the elastic materials consist mainly of alkane-like substances. Examination of the 1H NMR spectrum of triethylamine under the conditions of the reaction shows evidence of the occurrence of oxidative N dealkylation. The observed isotope effect demonstrates the existence of O-D cleavage resulting from the degradation of carbinolamine, which is the reported oxidation route of amines. Triethylamine acts here not only acts as a stabilizer and a reducing agent, but also as a precursor to build the alkane-like material upon which the gold thread is formed.     

Catalytic behaviour of gallium-containing mesoporous silicas (MCM-41) in the acetylation reaction

Liquid phase acetylation of 1,2-dimethoxybenzene with acetic anhydride has been examined for a series of acid gallium-mesoporous materials (MCM-41) with different Si/Ga ratios (Si/Ga = 80, 50 and 10) synthesized by microwave irradiation method. Physical adsorption of nitrogen, inductively coupled plasma, and the X-ray diffraction techniques, transmission electron microscopy, Fourier transform infrared spectroscopy, and a temperature-programmed desorption of pyridine were applied to characterize the catalysts. A mesoporous sample with Si/Ga = 10 showed better performance in the acid-cataiyzed acetylation of 1,2-dimethoxybenzene with acetic anhydride as an acylating agent. In addition, the kinetics of the reaction in the presence of these catalysts has been investigated.     

A family of ordered mesoporous carbons derived from mesophase pitch using ordered mesoporous silicas as templates

A variety of ordered mesoporous carbons (OMCs) were synthesized using ordered mesoporous silicas (OMSs) as hard templates and the mesophase pitch (MP) as a carbon precursor. The synthesis included the mixing of OMS with MP, the infiltration of OMS with MP at 450–550?°C and the carbonization of MP in OMS/MP composite followed by the dissolution of the OMS template. OMCs with structures of two-dimensional hexagonal arrays of nanorods and three-dimensional arrays of nanospheres were obtained through the replication of silica templates, including large-pore SBA-15, KIT-6, large-pore FDU-12 and SBA-16. In particular, 2-D hexagonal array of carbon nanorods (CMK-3 carbon) with (100) interplanar spacing of ～13 nm as well as an array of carbon nanospheres arranged in the face-centered cubic structure with the unit-cell parameter of 33 nm were successfully prepared. The specific surface areas of the resulting carbons were up to 400 m²/g, and the total pore volumes were up to 0.43 cm³/g, with the highest values achieved when the MP infiltration temperature was 500?°C. The OMCs exhibited narrow mesopore size distributions. As inferred from XRD, the frameworks of OMCs featured semi-graphitic structures even though moderate carbonization temperature (850?°C) was employed.     

Efficiency and application of poly(acryldinitrophenylamidrazone-dinitroacrylphenylhydrazine) chelating fiber for pre-concentrating and separating trace Au(III), Ru(III), In(III), Bi(III), Zr(IV), V(V), Ga(III) and Ti(IV) from solution samples

Poly(acryldinitrophenylamidrazone-dinitroacrylphenylhydrazine) chelating fiber was synthesized from polyacrylonitrile fiber and used for enrichment and separation for traces of Au(III), Ru(III), In(III), Bi(III), Zr(IV), V(V), Ga(III) and Ti(IV) ions from solution samples. The acidity, rate, re-use, capacity and interference on the adsorption of ions on the chelating fiber as well as the conditions of desorption of these ions from the chelating fiber were investigated by means of inductively coupled plasma optical emission spectrometry. The results show that 10-100 ngml(-1) of Au(III), Ru(III), In(III), Bi(III), Zr(IV), V(V), Ga(III) and Ti(IV) ions can be quantitatively enriched by the chelating fiber at a 2 mlmin(-1) of flow rate in the range pH 4-5, and desorbed quantitatively with 20 ml of 5 M HCl for In(III), Bi(III), Zr(IV), V(V), Ga(III), Ti(IV) and 20 ml of 4 M HCl+2% CS(NH(2))(2) solution for Au(III), Ru(III) (with recovery>95%). 50- to 500- fold excesses of Fe(III), Al(III), Mg(II), Mn(II), Ca(II), Cu(II), Ni(II) ions cause little interference in the concentration and determination of analyzed ions. When the fiber was reused for 8 times, the recoveries of the above ions enriched by the fiber were still over 87%. The relative standard deviations (RSDs) for the enrichment and determination of 10 ngml(-1) Au, Ru, In, Bi, Ga and 1 ngml(-1) Zr, V, Ti were lower than 3.0%. The results obtained for these ions in real solution samples by this method were basically in agreement with the given values with average errors of less than 6.3%. FT-IR spectra show that existence of NNCNHNH, OCNHNH and NO(2) functional groups are verified in chelating fiber, and Au(III) or Ru(III) is mainly combined with nitrogen (or oxygen) of the groups to form a chelate complex.