Spectrophotometric determination of thiocyanate ions in stratal waters

The formation of [FeSCN]²⁺ complex in hydrochloric and sulfuric acid medium was studied by spectrophotometry using iron(III) sulfate and ammonium iron(III) sulfate solutions as reactants. A method for the determination of 10–200 μg SCN^? in 25 mL water solutions containing ammonium iron(III) sulfate in sulfuric acid medium was developed; its determination limit is 2.6 μg (P = 0.99, n = 9). The method was applied for the analysis of model water samples with macro- and micro-component compositions similar to that of water from the Arigol licensed area. Operational control of the accuracy rate was performed by the standard addition method. The developed method can be applied to analyze water samples containing 1–90 mg/L thiocyanate ions.     

Spectrophotometric determination of uranium in natural waters

A method for the spectrophotometric determination of uranium in samples of natural water is described. Ion exchange with Amberlite IR-120 (H⁺) to concentrate the metal was used. The absorption properties of the complex formed between uranium and the chromogenic reagent Arsenazo III, its stability over several hours, the effect of the pH on the ability of the resin to retain uranium, the reproducibility of the method and the effects of ionic interferences were considered. The sensitivity was 0.67 and 0.05 μg l^?1 of uranium for the direct and the addition methods, respectively. Uranium concentrations for the samples analysed were between 0.10 and 0.50 μg l^?1.     

Spectrophotometric determination of polymeric flocculants in waters of different types

Previously studied reactions of the formation of ion associates between polyallyldimethylammonium chloride (PADAC) and triphenylmethane dyes were used in the determination of the residual concentration of polymeric flocculants. Rapid procedures were developed for analyzing hydrochemical objects of different types without the separation of PADAC and the effect of interferents was taken into account. The analysis of process solutions of water treatment was performed using the reaction with Xylenol Orange; the analysis of potable water and purified sewage waters was based on the reaction with Erythrosine. The precision of the procedures is at a level of RSD ≤ 20%. The systematic error does not exceed the tolerable level if the concentrations of metals and surfactants in the studied water are lower than their maximum permissible concentrations.     

Spectrophotometric determination of ethiofencarb in waters by reaction with p-aminophenol

Summary An automatized procedure has been developed for the spectrophotometric determination of ethiofencarb in water by reaction with p-aminophenol after alkaline hydrolysis to obtain the corresponding phenol sulphone. The hydrolyzed samples are continuously introduced into different manifolds at the same time as 300 mg/l p-aminophenol, 0.004 mol/l KIO₄ and 0.04 mol/l NaOH solutions. The absorbance is measured at 638 nm after a reaction time of 6 min in stop flow. This absorbance band corresponds to the indo dye obtained from the reaction between the phenol sulphone of ethiofencarb and the quinoneimine form of the p-aminophenol and it permits a matrix-free spectrophotometric determination of ethiofencarb with a limit of detection of 33 g/l. The recovery of ethiofencarb in different water matrices varies from 71 to 126%.     

Spectrophotometric determination of nitrite in polluted waters using 3-nitroaniline

Nitrite reacts with 3-nitroaniline in the presence of hydrochloric acid to form a diazonium cation, which is subsequently coupled with N-(1-naphtyl)ethylenediammonium chloride to form a stable purple azo dye. The method is suitable for the determination of 0.01–0.80 μg ml^?1 nitrite. The reactions are very fast and require no control of temperature. The observed molar absorptivity and Sandell's sensitivity of the azo dye are 4.9 × 10⁴ l mol^?1 cm^?1 and 9.4 × 10^?4 μg cm^?2, respectively. The method is free from most interferences. The method has been applied successfully to polluted river water.     

Spectrophotometric determination of aluminum and copper ions using spadns

Aluminum and copper ions are selectively estimated spectrophotometrically. These ions form colored complexes with spadns which have a maximum absorbance at 580 nm. The complexes formed with both cations are stable and pH dependant; aluminum is favorably complexed at pH 5, while copper is complexed at pH 7.The percentage recoveries were found to be 99.69 ± 0.75 and 99.32 ± 0.6 with a minimum detection limit of 0.08 and 0.23 g ml^–1 for aluminum and copper ions respectively. There is insignificant interference from the 10-fold concentrations of other metal ions under the proposed reaction conditions.     

Spectrophotometric determination of cyanide ions through ligand exchange reaction in solution

Summary A simple spectrophotometric method for the determination of trace amounts of cyanide ions in aqueous medium, using a heterocyclic azo dye complexed with mercury(II) for the first time, is described. The visual comparative method has been used in which a stronger complexing anion displaces a coloured reagent from the metal-ligand complex. Ammonium (2-amino-3-hydroxy-pyridyl-4 azo)benzene-4-arsonate (AHP-4A) complexed with mercury(II) has been used for the determination of 0.13–1.46g/ml of cyanide ions with fair accuracy. The anion has also been determined, when cyanide ion reacts with mercury(II)-(AHP-4A) complex, probably forming a bridged complex. The increase in absorbance is proportional to the cyanide ion concentration in the range of 0.04–0.37g/ml, but this method is not very precise. The effect of foreign ions has also been studied. The sensitivities of other mercury(II) complexes in the determination of cyanide ions have been compared.

---

Zusammenfassung Eine spektrophotometrische Methode zur Bestimmung von Spuren Cyanid in wäßrigem Milieu mit Hilfe eines mit Hg(II) komplexierten heterocyklischen Azofarbstoffes wurde beschrieben. Hierbei verdrängt ein stärker komplexierendes Anion das Farbreagens aus dem Metallkomplex. Ammonium(2-amino-3-hydroxypyridyl-4-azo)benzol-4-arsenat (AHP-4A) in komplexer Verbindung mit Hg(II) wurde für die genaue Bestimmung von 0,13–1,46g CN^–/ml verwendet. Das Anion wurde auch nach der Reaktion von Cyanid mit Hg(II)-(AHP-4A)-Komplex (wahrscheinlich zu einer Brückenverbindung) bestimmt. Der Anstieg der Extinktion ist der Cyanidkonzentration im Gebiet 0,04–0,37g/ml proportional, aber dieses Verfahren ist nicht sehr genau. Der Einfluß von Fremdionen wurde untersucht. Die Empfindlichkeit anderer Hg(II)-Komplexe wurde zum Vergleich herangezogen.

     

Spectrophotometric determination of nitrite in environmental waters using column preconcentration on biphenyl

Column preconcentration methods have been established for the spectrophotometric determination of trace nitrite with sulfanilic acid (SA) orp-aminoacetophenone (AAP) as the diazotizable aromatic amine andN, N-dimethylaniline (DMA) or 1-aminonaphthalene (AN) as the coupling agent, using differention-pairs co-precipitated with biphenyl. Nitrite ion reacts with SA in the pH range 2.0–3.0 and AAP in the pH range 1.7–3.0 in HCl medium to form water-soluble colourless diazonium cations. These cations are subsequently coupled with DMA in the pH range 3.7–6.1 for the SA-DMA system and AN in the pH range 1.7–2.3 for the AAP-AN system to be retained on microcrystalline biphenyl packed in a column. The solid mass is dissolved out from the column with 5 ml of DMF and the absorbance is measured by a spectrophotometer at 420 nm for the SA-DMA system and at 517 nm for the AAP-AN system. The calibration was linear over the concentration ranges 0.3–6.0 g of nitrite in 5 ml of DMF solution (i.e., 0.02–0.40 g/ml in the sample solution) for the SA-DMA system and 0.5–7.0 g of nitrite in 5 ml of DMF solution (i.e., 0.03–0.47 g/ml in the sample solution) for the AAP-AN system. The molar absorptivity and Sandell's sensitivity were respectively 2.63 × 10⁴lmol^–1cm^–1 and 1.75 × 10^–3 g cm^–2 for SA-DMA and 3.28 × 10⁴lmol^–1 cm^–1 and 1.40 × 10^–3 g cm^–2 for AAP-AN. The concentration factors were 4 and 16 for SA-DMA and AAP-AN, respectively. The detection limits were 0.0138 and 0.0175 g/ml NO₂ ^– for SA-DMA and AAP-AN, respectively. Seven replicate determinations of a solution containing 3.5 g of nitrite gave mean absorbances of 0.410 and 0.500 with relative standard deviations of 0.51 and 0.55% for SA-DMA and AAP-AN, respectively. Interference from various foreign ions has been studied and the methods have been applied to the determination of nitrite in environmental samples.     

微波催化显色反应分光光度法测定天然水中的磷

研究了用抗坏血酸作为还原剂磷钼蓝分光光度法测定磷时微波对于显色反应的催化作用和测定的适宜条件。试验表明:微波(高档,800W)可以使显色反应在3min内快速完成并稳定48h。线性范围:0~1.0mg/L,ε700nm=1.7×104L.mol-1.cm-1。对天然水样进行7次平行测定,其结果的RSD≤2.5%,回收率在98.6%~103%之间。与国家标准方法比较,无显著性差异。     

A gas chromatographic method for the determination of nitrite ions in natural waters

Following the treatment of the sample with zinc hydroxide, nitrite reacts with potassium iodide in the presence of acetone and sulphuric acid. The released iodine and the propanone derivative resulting from the acetone are extracted in n-hexane. The extract is subjected to gas chromatographic separation and detection using an electron capture detector. The calibration curve was found to be linear up to a concentration of 2.5 mg 1(-1) NO(-)(2). The detection limit calculated from the threefold noise level and the slope of the calibration curve is 0.008 mg 1(-1). The relative standard deviation (including that of the blank) was less than 8%. The reliability of the method is adequate for practical uses. Amongst the advantages is that the method does not require the use of exceedingly toxic reagents. On the other hand, the method is applicable for samples that even after being subjected to clarification procedures still do not become fully transparent.     

Spectrophotometric determination of chloride in waters using a multisyringe flow injection system

A multisyringe flow injection system (MSFIA) with spectrophotometric detection is proposed as a fast, robust and low-reagent consumption system for the determination of chloride (Cl⁻) in waters. The system is based in the classic reaction of Cl⁻ with Fe³⁺ and Hg(SCN)₂, but due to the hazardous properties of this last reagent, the proposed methodology has been developed with the aim to minimize the consumption of this one, consuming less than 0.05 mg of Hg for a Cl⁻ determination, being the system of this type with the lowest Hg consumption. The linear working range was between 1 and 40 mg L⁻¹ Cl⁻ and the detection limit was 0.2 mg L⁻¹ Cl⁻. The repeatability (RSD) was 0.8% for a 10 mg L⁻¹ Cl⁻ solution, and the injection throughput was 130 h⁻¹. The proposed system is compared with other chloride monitoring flow systems, this comparison is realized with a point of view of the equilibrium between the obtained analytical features and produced residues toxicity. The proposed system was applied to the determination of Cl⁻ in mineral, tap and well water.     

Flow-through solid-phase based optical sensor for the multisyringe flow injection trace determination of orthophosphate in waters with chemiluminescence detection

In this work, a novel flow-through solid-phase based chemiluminescence (CL) optical sensor is described for the trace determination of orthophosphate in waters exploiting the multisyringe flow injection analysis (MSFIA) concept with multicommutation. The proposed time-based injection flow system relies upon the in-line derivatisation of the analyte with ammonium molybdate in the presence of vanadate, and the transient immobilisation of the resulting heteropolyacid in a N-vinylpyrrolidone/divinylbenzene copolymer packed spiral shape flow-through cell located in front of the window of a photomultiplier tube. The simultaneous injection of well-defined slugs of luminol in alkaline medium and methanol solution towards the packed reactor is afterwards performed by proper switching of the solenoid valves. Then, the light emission from the luminol oxidation by the oxidant species retained onto the sorbent material is readily detected. At the same time, the generated molybdenum-blue compound is eluted by the minute amount of injected methanol, rendering the system prepared for a new measuring cycle. Therefore, the devised sensor enables the integration of the solid-phase CL reaction with elution and detection of the emitted light without the typical drawbacks of the molybdenum-blue based spectrophotometric procedures regarding the excess of molybdate anion, which causes high background signals due to its self-reduction. The noteworthy features of the developed CL-MSFIA system are the feasibility to accommodate reactions with different pH requirements and the ability to determine trace levels of orthophosphate in high silicate content samples (Si/P ratios up to 500). Under the optimised conditions, a dynamic linear range from 5 to 50 μg P l⁻¹ for a 1.8 ml sample, repeatability better than 3.0% and a quantification limit of 4 μg P l⁻¹ were attained. The flowing stream system handles 11 analysis h⁻¹ and has been successfully applied to the determination of trace levels of orthophosphate in environmental samples such as mineral, ground, tap and pond waters as well as samples from a water-steam cycle of an incineration plant. The t-test comparison of the means for the developed optical sensor and the molybdenum-blue spectrophotometric APHA/AWWA/WPCF reference method revealed that there is no evidence of significant differences between the obtained results at the 95% confidence level.     

Spectrophotometric determination of chloride in mineral and drinking waters using sequential injection analysis

An on-line sequential injection system has been developed for spectrophotometric determination of chloride in drinking mineral, natural, and ground waters. Samples containing different concentrations of chloride were analyzed. The analysis is based on detection of the red iron(III) thiocyanate complex. The complex was monitored spectrophotometrically at 480 nm using de-ionized water as the carrier stream at a flow rate of 3.21 mL min(-1). The method was found to be linear within the range 0-50 mg L(-1) chloride; the detection limit was 3.01 mg L(-1). The fully automated method can be used to analyze 37 samples per hour with a relative standard deviation (RSD) better than 2.50%.     

Spectrophotometric reaction-rate method for the determination of nitrite in waters with pyridine-2-aldehyde 2-pyridylhydrazone

A method for the kinetic determination of submicrogram amounts of nitrite has been developed, based on its acceleration of the rate of bromate oxidation of pyridine-2-aldehyde 2-pyridylhydrazone in acidic medium. The reaction is monitored spectrophotometrically at 372 nm. A comparative study with hydrochloric acid and perchloric acid media shows that the analytical parameters are affected by the type of acid used. Within-day precision, based on ten replicate determinations, was better than 0.011 μ/ml, which corresponds to 2.2-1.5% relative standard deviation at the concentrations examined. Application of this method in the determination of nitrite in water has been discussed. The recovery of nitrite from drinking waters ranges from 90 to 117% and the average relative standard deviation for nitrite determinations in polluted river water is 3.2%. Large amounts of nitrate and ammonium ions do not interfere. However, there is interference by Cu²⁺, Pd²⁺ and electroactive substances. Major advantages for the method are simplicity, absence of a reagent blank, and the wide determination range.     

Highly sensitive redox-photometric determination of selenite and iodide ions in mineral waters

The use of two-phase reactions involving the antimony(V) hexachloride complex was proposed for the redox-photometric determination of selenite and iodide ions in some potable mineral waters with detection limits of 5 × 10^?5 and 3 × 10^?5 mg/L, respectively. The procedures exhibit a high selectivity and reproducibility and do not require lacking reagents and expensive instrumentation. The relative standard deviation is no higher than 20%.     

Spectrophotometric determination of uranium in natural waters after preconcentration on TBP-plasticized dibenzoylmethane-loaded polyurethane foams

A method is presented for the spectrophotometric determination of uranium in natural waters after a preconcentration step involving percolation of a suitable aliquot of the water sample whose pH is adjusted to 6.0–6.5 through a TBP-plasticized dibenzoylmethane-loaded polyurethane foam bed. Uranium on the foam is eluted with 0.6M HCl solution and then determined spectrophotometrically using arsenazo III as a chromogenic reagent.     

Spectrophotometric determination of aluminium and gallium with pyrogallol red and cetyltrimethylammonium ions

Spectrophotometric methods are described for the determination of microgram amounts of aluminium and gallium based on the formation of a ternary complex between the metal, pyrogallol red, and cetyltrimethylammonium bromide. The complexes have absorbance maxima at 610 and 615 nm, respectively, with molar absorptivities of 4.8 × 10⁴(Al)and 1.0 × 10⁵ liter mol^?1 cm^?1 (Ga). Numerous metals interfere. Gallium can be separated by extraction of gallium from 7 M hydrochloric acid with di-isopropyl ether. However, aluminium can be separated by extraction of interfering ions with cupferron.     

Flow-injection potentiometric determination of trace concentrations of chloride ions in low-mineralized natural waters

A procedure is developed for flow-injection potentiometric determination of trace chloride ions in low-mineralized waters and atmospheric precipitations. The procedure excludes the stage of preliminary ion-exchange concentration. The quantification limit in a 5-min analysis is 0.4 mg/L.