Adsorption of small Au(n) (n = 1-5) and Au-Pd clusters inside the TS-1 and S-1 pores

We used a hybrid quantum-mechanics/molecular-mechanics (QM/MM) approach to simulate the adsorption of Au(n)() (n = 1-5), AuPd, and Au(2)Pd(2) clusters inside the TS-1 and S-1 pores. We studied nondefect and metal-vacancy defect sites in TS-1 and S-1 for a total of four different environments around the T6 crystallographic site. We predict stronger binding of all clusters near Ti sites in Ti-substituted framework compared to adsorption near Si sites-consistent with the experimental finding of a direct correlation between the Ti-loading and the Au-loading on the Au/TS-1 catalysts with high Si/Ti ratio. The cluster binding is also stronger near lattice-metal vacancies compared to fully coordinated, nondefect sites. In all the cases, a trend of binding energy (BE) versus Au cluster size (n) shows a peak at around n = 3-4. Our results show that there is enough room for the attack of H(2)O(2) on the Ti-defect site even with Au(1-4) adsorbed-a result that supports the possibility of H(2)O(2) spillover from the Au clusters to the adjacent Ti-defect sites. Mulliken charge analysis indicates that in all the cases there is electron density transfer to adsorbed clusters from the zeolite lattice. In the case of both gas-phase and adsorbed Au-Pd clusters, all the Pd atoms were positively charged, and all the Au atoms were negatively charged due to the higher electron-affinity of Au. We also found a correlation between the BE and the charge transfer to the clusters (the higher the charge transfer to the clusters, the higher the BE), and a universal correlation was found for Au(2-5) when BE and charge transfer were plotted on a per atom basis. A relatively larger charge transfer to the adsorbed clusters was found for the Ti sites versus the Si sites, and for the defect sites versus the nondefect sites. The trends in the BE were corroborated using Gibbs free energy of adsorption (DeltaG(ads)), and the implications of DeltaG(ads) in sintering of Au clusters are also discussed. Our results confirm that electronic factors such as cluster-charging are potentially important support effects for the Au/TS-1 catalyst.     

Theoretical study of oxygen adsorption on pure Au(n+1)+ and doped MAu(n)+ cationic gold clusters for M = Ti, Fe and n = 3-7

A comparative study of the adsorption of an O2 molecule on pure Au(n+1)+ and doped MAu(n)+ cationic gold clusters for n = 3-7 and M = Ti, Fe is presented. The simultaneous adsorption of two oxygen atoms also was studied. This work was performed by means of first principles calculations based on norm-conserving pseudo-potentials and numerical basis sets. For pure Au4 +, Au6+, and Au7+ clusters, the O2 molecule is adsorbed preferably on top of low coordinated Au atoms, with an adsorption energy smaller than 0.5 eV. Instead, for Au5+ and Au8+, bridge adsorption sites are preferred with adsorption energies of 0.56 and 0.69 eV, respectively. The ground-state geometry of Au(n)+ is almost unperturbed after O2 adsorption. The electronic charge flows towards O2 when the molecule is adsorbed in bridge positions and towards the gold cluster when O2 is adsorbed on top of Au atoms, and both the adsorption energy and the O-O bond length of adsorbed oxygen increase when the amount of electronic charge on O2 increases. On the other hand, we studied the adsorption of an O2 molecule on doped MAu(n)+ clusters, leading to the formation of (MAu(n)O2+) ad complexes with different equilibrium configurations. The highest adsorption energy was obtained when both atoms of O2 bind on top of the M impurity, and it is larger for Ti doped clusters than for Fe doped clusters, showing an odd-even effect trend with size n, which is opposite for Ti as compared to Fe complexes. For those adsorption configurations of (MAu(n)O2+) ad involving only Au sites, the adsorption energy is similar to or smaller than that for similar configurations of Au(n)+1O2 + complexes. However, the highest adsorption energy of (MAu(n)O2+) ad is higher than that for (Au(n)+1O2+) ad by a factor of approximately 4.0 (1.2) for M = Ti (M = Fe). The trends with size n are rationalized in terms of O-O and O-M bond distances, as well as charge transfer between oxygen and cluster substrates. The spin multiplicity of those (MAu(n)O2+) ad complexes with the highest O2 adsorption energy is a maximum (minimum) for M = Fe (Ti), corresponding to parallel (anti-parallel) spin coupling of MAu(n)+ clusters and O2 molecules. Finally, we obtained the minimum energy equilibrium structure of complexes (Au(n)O2+) dis and (MAu(n)O2+) dis containing two separated O atoms bonded at different sites of Au(n)+ and MAu(n)+ clusters, respectively. For (MAu(n)O2 (+)) dis, the equilibrium configuration with the highest adsorption energy is stable against separation in MAu(n)+ and O2 fragments, respectively. Instead, for (Au(n)O2+) dis, only the complex n = 6 is stable against separation in Au(n)+ and O2 fragments. The maximum separation energy of (MAu(n)O2+) dis is higher than the O2 adsorption energy of (MAu(n)O2+) ad complexes by factors of approximately 1.6 (2.5), 1.6 (1.7), 1.5 (2.4), 1.5 (1.3), and 1.6 (1.8) for M = Ti (Fe) complexes in the range n = 3-7, respectively.     

CO adsorption on pure and binary-alloy gold clusters: a quantum chemical study

We performed density-functional theory analysis of nondissociative CO adsorption on 22 binary Au-alloy (Au(n)M(m)) clusters: n=0-3, m=0-3, and m+n=2 (dimers) or 3 (trimers), M=Cu/Ag/Pd/Pt. We report basis-set superposition error corrections to adsorption energies and include both internal energy of adsorption (DeltaU(ads)) and Gibbs free energy of adsorption (DeltaG(ads)) at standard conditions (298.15 K and 1 atm). We found onefold (atop) CO binding on all the clusters except Pd2 (twofold/bridged), Pt2 (twofold/bridged), and Pd3 (threefold). In agreement with the experimental results, we found that CO adsorption is thermodynamically favorable on pure Au/Cu clusters but not on pure Ag clusters and also observed the following adsorption affinity trend: Pd>Pt>Au>Cu>Ag. For alloy dimers we found the following patterns: Au2>M Au>M2 (M=Ag/Cu) and M2>M Au>Au2 (M=Pd/Pt). Alloying Ag/Cu dimers with (more reactive) Au enhanced adsorption and the opposite effect was observed for PdPt dimers. The Ag-Au, Cu-Au, and Pd-Au trimers followed the trends observed on dimers: Au3>M Au2>M2Au>M3 (M=Ag/Cu) and Pd3>Pd2Au>PdAu2>Au3. Interestingly, Pt-Au trimers reacted differently and alloying with Au systematically increased the adsorption affinity: PtAu2>Pt2Au>Pt3>Au3. A strikingly different behavior of Pt is also manifested by the triplet spin state and onefold (atop) binding in Pt3-CO which is in contradiction with the singlet spin state and threefold binding in Pd3-CO. We found a linear correlation between CO binding energy (BE) and elongation of the CO bond. For Ag-Au and Cu-Au clusters, the increase in CO BE (and elongation of the C-O bond which is probably due to the back donation) is accompanied by the decrease in the cluster-CO distance suggesting that the donation (from 5sigma highest occupied molecular orbital in CO to cluster lowest unoccupied molecular orbital) mechanism also contributes to the BE. For Pd-Au clusters, the cluster-CO distance (and CO bond length) increases with increase in the BE, suggesting that the donation mechanism may not be important for those clusters. No clear trend was observed for Pt-Au clusters.     

First-principles investigation of transition metal atom M (M = Cu, Ag, Au) adsorption on CeO2(110)

Transition metal atom M (M = Cu, Ag, Au) adsorption on CeO(2)(110), a technologically important catalytic support surface, is investigated with density-functional theory within the DFT+U formalism. A set of model configurations was generated by placing M at three surface sites, viz., on top of an O, an O bridge site, and a Ce bridge site. Prior to DFT optimization, small distortions in selected Ce-O distances were imposed to explore the energetics associated with reduction of Ce(4+) to Ce(3+) due to charge transfer to Ce during M adsorption. Charge redistribution is confirmed with spin density isosurfaces and site projected density of states. We demonstrate that Cu and Au atoms can be oxidized to Cu(2+) and Au(2+), although the adsorption energy, E(ads), of Au(2+) is less favorable and, unlike Cu(2+), it has not been experimentally observed. Oxidation of Ag always results in Ag(+). For M adsorption at an O bridge site, E(ads)(2NN) > E(ads)(3NN) > E(ads)(1NN) where NN denotes the nearest neighbor Ce(3+) site relative to M. Alternatively, for M adsorption at a Ce bridge site, E(ads)(3NN) > E(ads)(2NN) > E(ads)(1NN). The adsorption behavior of M on CeO(2) (110) is compared with M adsorption on CeO(2)(111).     

Au12M (M=Na,Mg, Al,Si, P,S, Cl)团簇的结构、稳定性和电子性质

采用基于密度泛函理论的第一性原理方法系统地研究了Au12M(M=Na,Mg,Al,Si,P,S,Cl)团簇的结构、稳定性和电子性质.对团簇的平均结合能、镶嵌能、垂直离化势、最高占据分子轨道(HOMO)和最低未占据分子轨道(LUMO)的能级差、电荷布居分析、自然键轨道(NBO)进行了计算和讨论.对于Au12M(M=Na,Mg,Al)团簇,它们形成了内含M原子的最稳定的笼状结构.然而对于Au12M(M=Si,P,S,Cl)团簇,它们却形成了以M元素为顶点的稳定锥形结构.在这些团簇中发现Au12S团簇相对是最稳定的,这是由于Au12S团簇形成了稳定的满壳层的电子结构.自然电荷布居分析表明:对于所有的Au12M(M=Na,Mg,Al,Si,P,S,Cl)团簇电荷总是从Au原子转向M原子.自然键轨道和HOMO分析表明Au12M团簇中发生了Au原子的s-d轨道和M原子的p轨道间的杂化现象.     

Adsorption of O2 on tubelike Au24 and Au24- clusters

The nondissociative adsorptions of O(2) on the neutral and anionic Au(24) have been studied using the density functional theory (DFT) in the generalized gradient approximation. Their geometrical structures are optimized by using a combination of the relativistic effective core potential and all-electron potential with scalar relativistic corrections. It is found that the adsorptions of O(2) on the tubelike Au(24) and Au(24) (-) are more stable than it on their space-filled counterparts. Mulliken population analysis shows that the O(2) adsorbed on the tubelike Au(24) and Au(24) (-) got more electrons than on the amorphous ones, which may be a reason why the O(2) can be adsorbed more easily on the former rather than on the latter. Compared with the previous DFT studies of O(2) adsorbed on small Au(n) (n< or =10) clusters, we have shown that the O(2) can also be adsorbed on the neutral even Au(24) with an adsorption energy compatible with that on the small neutral odd gold clusters, but the adsorption energy of O(2) on the anionic Au(24) (-) is lower than that on the small anionic Au(n) with even n. In all the optimized geometrical structures of the O(2)-adsorbed Au(24) and Au(24) (-) clusters, including both tubelike and amorphous ones, we found that O(2) prefers its two O atoms to be attached to two near gold atoms with the least coordination number rather than only one O atom to be attached to one gold atom.     

Adsorption of molecular hydrogen and hydrogen sulfide on Au clusters

The authors present theoretical results describing the adsorption of H2 and H2S molecules on small neutral and cationic gold clusters (Au(n)((0/+1)), n=1-8) using density functional theory with the generalized gradient approximation. Lowest energy structures of the gold clusters along with their isomers are considered in the optimization process for molecular adsorption. The adsorption energies of H2S molecule on the cationic clusters are generally greater than those on the corresponding neutral clusters. These are also greater than the H2 adsorption energies on the corresponding cationic and neutral clusters. The adsorption energies for cationic clusters decrease with increasing cluster size. This fact is reflected in the elongations of the Au-S and Au-H bonds indicating weak adsorption as the cluster grows. In most cases, the geometry of the lowest energy gold cluster remains planar even after the adsorption. In addition, the adsorbed molecule gets adjusted such that its center of mass lies on the plane of the gold cluster. Study of the orbital charge density of the gold adsorbed H2S molecule reveals that conduction is possible through molecular orbitals other than the lowest unoccupied molecular orbital level. The dissociation of the cationic Au(n)SH2+ cluster into Au(n)S+ and H2 is preferred over the dissociation into Au(m)SH2+ and Au(n-m), where n=2-8 and m=1-(n-1). H2S adsorbed clusters with odd number of gold atoms are more stable than neighboring even n clusters.     

The mechanism of emerging catalytic activity of gold nano-clusters on rutile TiO2(110) in CO oxidation reaction

This paper reveals the fact that the O adatoms (O(ad)) adsorbed on the 5-fold Ti rows of rutile TiO(2)(110) react with CO to form CO(2) at room temperature and the oxidation reaction is pronouncedly enhanced by Au nano-clusters deposited on the above O-rich TiO(2)(110) surfaces. The optimum activity is obtained for 2D clusters with a lateral size of ～1.5 nm and two-atomic layer height corresponding to ～50 Au atoms∕cluster. This strong activity emerging is attributed to an electronic charge transfer from Au clusters to O-rich TiO(2)(110) supports observed clearly by work function measurement, which results in an interface dipole. The interface dipoles lower the potential barrier for dissociative O(2) adsorption on the surface and also enhance the reaction of CO with the O(ad) atoms to form CO(2) owing to the electric field of the interface dipoles, which generate an attractive force upon polar CO molecules and thus prolong the duration time on the Au nano-clusters. This electric field is screened by the valence electrons of Au clusters except near the perimeter interfaces, thereby the activity is diminished for three-dimensional clusters with a larger size.     

The influence of metal cluster size on adsorption energies: CO adsorbed on Au clusters supported on TiO2

Infrared reflection absorption spectroscopy (IRAS) has been used to study CO adsorption on Au clusters ranging in size from 1.8 to 3.1 nm, supported on TiO(2). The adsorbed CO vibrational frequency blue-shifts slightly (approximately 4 cm(-)(1)) compared to that adsorbed on bulk Au, whereas the heats of adsorption (-DeltaH(ads)) increase sharply with decreasing cluster size, from 12.5 to 18.3 kcal/mol.     

Density functional theory study of the adsorption of formaldehyde on Pd4 and on Pd4/gamma-Al2O3 clusters

B3LYP/LANL2DZ and B3LYP/6-31G(d)-restricted and -unrestricted calculations are employed to calculate energies and adsorption forms of formaldehyde adsorbed on planar and on tetrahedral Pd4 clusters and on a Pd4 cluster supported on Al10O15. Formaldehyde adsorbs on planar Pd4 in the eta(2)(C,O)-di-sigma adsorption mode, while on tetrahedral Pd4, it adsorbs in the eta(2)(C,O)-pi adsorption mode. The adsorption energy on planar Pd4 is -21.4 kcal x mol(-1), whereas for the tetrahedral Pd4 cluster, the adsorption energy is -13.2 kcal x mol(-1). The latter value is close to experimental findings (-12 to -14 kcal x mol(-1)). Adsorption of formaldehyde on Pd4 supported on an Al10O15 cluster leads essentially to the same result as that found for adsorption on the tetrahedral Pd4 cluster. Charge density analysis for the interaction between formaldehyde and the Pd4 clusters indicates strong backdonation in the eta(2) adsorption mode, leading to positive charge on the Pd4 cluster. NBO analysis shows that the highly coordinated octahedral aluminum atoms of Al10O15 donate electron density to the supported Pd4 cluster, while tetrahedral aluminum atoms with lower coordination number have acidic nature and therefore act as electron acceptors.     

System-dependent dispersion coefficients for the DFT-D3 treatment of adsorption processes on ionic surfaces

Dispersion-corrected density functional theory calculations (DFT-D3) were performed for the adsorption of CO on MgO and C(2) H(2) on NaCl surfaces. An extension of our non-empirical scheme for the computation of atom-in-molecules dispersion coefficients is proposed. It is based on electrostatically embedded M(4)X(4) (M=Na, Mg) clusters that are used in TDDFT calculations of dynamic dipole polarizabilities. We find that the C(MM)(6) dispersion coefficients for bulk NaCl and MgO are reduced by factors of about 100 and 35 for Na and Mg, respectively, compared to the values of the free atoms. These are used in periodic DFT calculations with the revPBE semi-local density functional. As demonstrated by calculations of adsorption potential energy curves, the new C(6) coefficients lead to much more accurate energies (E(ads)) and molecule-surface distances than with previous DFT-D schemes. For NaCl/C(2) H(2) we obtained at the revPBE-D3(BJ) level a value of E(ads) =-7.4 kcal mol(-1) in good agreement with experimental data (-5.7 to -7.1 kcal mol(-1)). Dispersion-uncorrected DFT yields an unbound surface state. For the MgO/CO system, the computed revPBE-D3(BJ) value of E(ads) =-4.1 kcal mol(-1) is also in reasonable agreement with experimental results (-3.0 kcal mol(-1)) when thermal corrections are taken into account. Our new dispersion correction also improves computed lattice constants of the bulk systems significantly compared to plain DFT or previous DFT-D results. The extended DFT-D3 scheme also provides accurate non-covalent interactions for ionic systems without empirical adjustments and is suggested as a general tool in surface science.     

Adsorption of O2 and oxidation of CO at Au nanoparticles supported by TiO2(110)

Density functional theory calculations are performed for the adsorption of O2, coadsorption of CO, and the CO+O2 reaction at the interfacial perimeter of nanoparticles supported by rutile TiO2(110). Both stoichiometric and reduced TiO2 surfaces are considered, with various relative arrangements of the supported Au particles with respect to the substrate vacancies. Rather stable binding configurations are found for the O2 adsorbed either at the trough Ti atoms or leaning against the Au particles. The presence of a supported Au particle strongly stabilizes the adsorption of O2. A sizable electronic charge transfer from the Au to the O2 is found together with a concomitant electronic polarization of the support meaning that the substrate is mediating the charge transfer. The O2 attains two different charge states, with either one or two surplus electrons depending on the precise O2 adsorption site at or in front of the Au particle. From the least charged state, the O2 can react with CO adsorbed at the edge sites of the Au particles leading to the formation of CO2 with very low (approximately 0.15 eV) energy barriers.     

CO在M55（M=Cu,Ag,Au）团簇上吸附的密度泛函研究

在全电子相对论BVP86/DNP水平下对CO在Au55,Ag55和Cu55团簇上的吸附进行了比较研究,并考察了电荷对吸附的影响.计算结果表明,CO在Au55团簇上吸附能最大,其次为Cu55团簇,最弱的为Ag55团簇.团簇电荷对C—O键活化和CO与团簇表面原子成键影响较小.金团簇的电荷对吸附能影响较大,而银和铜团簇的电荷对吸附能影响较小.CO吸附到团簇上导致团簇上电子向CO转移.C—O键活化强度与吸附位置密切相关,其中孔位吸附导致C—O键活化程度最大,最弱的为顶位吸附.CO在金团簇上吸附具有较好选择性,而在银和铜团簇上吸附无选择性.     

双空位缺陷双层石墨烯储钠性能的第一性原理研究

采用基于密度泛函理论(DFT)的色散修正方法,研究了Na吸附和嵌入在双空位缺陷(DV)双层石墨烯(BLG)体系中的形成能、电荷转移、电极电势和扩散行为。形成能计算表明,无论单个Na原子在BLG表面吸附还是层间嵌入,均在DV空位中心处更稳定。电荷密度分布和Bader电荷计算表明Na与BLG的结合方式表现出离子性。Na嵌入DV缺陷BLG层间,缺陷浓度增加使BLG由AB堆垛向AA堆垛转变过程推迟;使Na在DV缺陷BLG的表面和层间能够稳定储钠的容量之和增至262.75 mAh?g~(-1),对应浓度Na与C摩尔比为2:17,储钠浓度继续增加,Na在BLG表面吸附容易产生枝晶或团簇。当层间嵌入Na原子时,表面Na原子向DV缺陷中心方向扩散能垒减小、表面Na原子沿相反方向的扩散能垒增加,DV缺陷的存在提高了BLG表面捕获Na的能力。     

O与O2在Au团簇上吸附的密度泛函理论研究

采用基于密度泛函理论(DFT)的Dmol³程序系统研究了O原子与O₂在 Au₁₉与Au₂₀团簇上的吸附反应行为. 结果表明: O在Au₁₉团簇顶端洞位上的吸附较Au₂₀强; 在侧桥位吸附强度相近. O与O₂在带负电Au团簇上吸附较强, 在正电团簇吸附较弱. 从O―O键长看, 当金团簇带负电时, O―O键长较长, 中性团簇次之, 正电团簇中O―O键长较短, 因而O₂活化程度依次减弱. 电荷布居分析表明, Au团簇带负电时, O与O₂得电子数较中性团簇多, 而团簇带正电时, 得电子数较少. 差分电荷密度(CDD)表明, O₂与Au团簇作用时, 金团簇失电子, O₂的π^*轨道得电子, 使O―O键活化. O₂在Au₁₉^-团簇上解离反应活化能为1.33 eV, 较中性团簇低0.53 eV; 而在Au₁₉⁺上活化能为2.27 eV, 较中性团簇高0.41 eV, 这与O₂在不同电性Au₁₉团簇O―O键活化规律相一致.     

Computational study of ethanol adsorption and reaction over rutile TiO(2) (110) surfaces

Studies of the modes of adsorption and the associated changes in electronic structures of renewable organic compounds are needed in order to understand the fundamentals behind surface reactions of catalysts for future energies. Using planewave density functional theory (DFT) calculations, the adsorption of ethanol on perfect and O-defected TiO(2) rutile (110) surfaces was examined. On both surfaces the dissociative adsorption mode on five-fold coordinated Ti cations (Ti(4+)(5c)) was found to be more favourable than the molecular adsorption mode. On the stoichiometric surface E(ads) was found to be equal to 0.85 eV for the ethoxide mode and equal to 0.76 eV for the molecular mode. These energies slightly increased when adsorption occurred on the Ti(4+)(5c) closest to the O-defected site. However, both considerably increased when adsorption occurred at the removed bridging surface O; interacting with Ti(3+) cations. In this case the dissociative adsorption becomes strongly favoured (E(ads) = 1.28 eV for molecular adsorption and 2.27 eV for dissociative adsorption). Geometry and electronic structures of adsorbed ethanol were analysed in detail on the stoichiometric surface. Ethanol does not undergo major changes in its structure upon adsorption with its C-O bond rotating nearly freely on the surface. Bonding to surface Ti atoms is a σ type transfer from the O2p of the ethanol-ethoxide species. Both ethanol and ethoxide present potential hole traps on O lone pairs. Charge density and work function analyses also suggest charge transfer from the adsorbate to the surface, in which the dissociative adsorptions show a larger charge transfer than the molecular adsorption mode.     

Enhanced adsorption energy of Au1 and O2 on the stoichiometric TiO2(110) surface by coadsorption with other molecules

During heterogeneous catalysis the surface is simultaneously covered by several adsorbed molecules. The manner in which the presence of one kind of molecule affects the adsorption of a molecule of another kind has been of interest for a long time. In most cases the presence of one adsorbate does not change substantially the binding energy of another adsorbate. The calculations presented here show that the stoichiometric rutile TiO(2)(110) surface, on which one of the compounds -OH, Au(3), Au(5), Au(7), Na, K, or Cs or two different gold strips was preadsorbed, behaves differently: the binding energy of Au(1) or O(2) to such a surface is much stronger than the binding to the clean stoichiometric TiO(2)(110) surface. Moreover, the binding energy of Au(1) or O(2) and the amount of charge they take from the surface when they adsorb are the same, regardless of which of the above species is preadsorbed. The preadsorbed species donate electrons to the conduction band of the oxide, and these electrons are used by Au(1) or O(2) to make stronger bonds with the surface. This suggests that adding an electron to the conduction band of the clean stoichiometric TiO(2)(110) slab used in the calculation will affect similarly the adsorption energy of Au(1) or O(2). Our calculations show that it does. We have also studied how the preadsorption of Au(4) or Au(6) affects the binding of Au(1) or O(2) to the surface. These two gold clusters do not donate electrons to the surface when they bind to it and therefore should not influence substantially the binding energy of Au(1) or O(2) to the surface. However, adsorbing O(2) or Au(1) on the surface forces the clusters to change their structure into that of isomers that donate charge to the oxide. This charge is used by Au(1) or O(2) to bind to the surface and the energy of this bond exceeds the isomerization energy. As a result the surface with the isomerized cluster is the lowest energy state of the system. We believe that these results can be generalized as follows. The molecules that we coadsorbed with Au(1) or O(2) donate electrons to the oxide and are Lewis bases. By giving the surface high energy electrons, they turn it into a Lewis base and this increases its ability to bind strong Lewis acids such as Au(1) and O(2). We speculate that this kind of interaction is general and may be observed for other oxides and for other coadsorbed Lewis base-Lewis acid pairs.     

Density functional study of the charge on Aun clusters (n=1-7) supported on a partially reduced rutile TiO2(110): are all clusters negatively charged?

It is widely believed that small gold clusters supported on an oxide surface and adsorbed at the site of an oxygen vacancy are negatively charged. It has been suggested that this negative charge helps a gold cluster adsorb oxygen and weakens the O-O bond to make oxidation reactions more efficient. Given the fact that an oxygen vacancy is electron rich and that Au is a very electronegative element, the assumption that the Au cluster will take electron density from the vacancy is plausible. However, the density functional calculations presented here show that the situation is more complicated. The authors have used the Bader method to examine the charge redistribution when a Aun cluster (n=1-7) binds next to or at an oxygen vacancy on rutile TiO2(110). For the lowest energy isomers they find that Au1 and Au3 are negatively charged, Au5 and Au7 are positively charged, and Au2, Au4, and Au6 exchange practically no charge. The behavior of the Aun isomers having the second-lowest energy is also unexpected. Au2, Au3, Au5, and Au7 are negatively charged upon adsorption and very little charge is transferred when Au4 and Au6 are adsorbed. These observations can be explained in terms of the overlap between the frontier molecular orbitals of the gold cluster and the eigenstates of the support. Aun with even n becomes negatively charged when the lowest unoccupied molecular orbital has a lobe pointing in the direction of the oxygen vacancy or towards a fivefold coordinated Ti (5c-Ti) located in the surface layer; otherwise it stays neutral. Aun with odd n becomes negatively charged when the singly occupied molecular orbital has a lobe pointing in the direction of a 5c-Ti located at the vacancy site or in the surface layer, otherwise it donates electron density into the conduction band of rutile TiO2(110) becoming positively charged.     

Glucose interaction with Au,Ag, and Cu clusters: Theoretical investigation

Interactions of α‐D ‐glucose with gold, silver, and copper metal clusters are studied theoretically at the density functional theory (CAM‐B3LYP) and MP2 levels of theory, using trimer clusters as simple catalytic models for metal particles as well as investigating the effect of cluster charge by studying the interactions of cationic and anionic gold clusters with glucose. The bonding between α‐D ‐glucose and metal clusters occurs by two major bonding factors; the anchoring of M atoms (M = Cu, Ag, and Au) to the O atoms, and the unconventional M…H? O hydrogen bond. Depending on the charge of metal clusters, each of these bonds contributes significantly to the complexation. Binding energy calculations indicate that the silver cluster has the lowest and gold cluster has the highest affinity to interact with glucose. Natural bond orbital analysis is performed to calculate natural population analysis and charge transfers in the complexes. Quantum theory of atoms in molecules was also applied to interpret the nature of bonds. © 2012 Wiley Periodicals, Inc.     

Interaction of Pt clusters with the anatase TiO(2)(101) surface: a first principles study

The adsorption of Pt(n)() (n = 1-3) clusters on the defect-free anatase TiO(2)(101) surface has been studied using total energy pseudopotential calculations based on density functional theory. The defect-free anatase TiO(2)(101) surface has a stepped structure with a step width of two O-Ti bond distances in the (100) plane along the [10] direction and the edge of the step is formed by 2-fold-coordinated oxygen atoms along the [010] direction. For a single Pt adatom, three adsorption sites were found to be stable. Energetically, the Pt adatom prefers the bridge site formed by 2 2-fold-coordinated oxygen atoms with an adsorption energy of 2.84 eV. Electronic structure analysis showed that the Pt-O bonds formed upon Pt adsorption are covalent. Among six stable Pt(2) adsorption configurations examined, Pt(2) was found to energetically favor the O-O bridge sites on the step edge along [010] with the Pt-Pt bond axis perpendicular to [010]. In these configurations, one of the Pt atoms occupies the same O-O bridge site as for a single Pt adatom and the other one either binds a different 2-fold-coordinated oxygen atom on the upper step or a 5-fold-coordinated Ti atom on the lower terrace. Three triangular and three open Pt(3) structures were determined as minima for Pt(3) adsorption on the surface. Platinum trimers adsorbed in triangular structures are more stable than in open structures. In the most stable configuration, Pt(3) occupies the edge O-O site with the Pt(3) plane being upright and almost perpendicular to the [001] terrace. The preference of Pt(n)() to the coordinately unsaturated 2-fold-coordinated oxygen sites indicates that these sites may serve as nucleation centers for the growth of metal clusters on the oxide surface. The increase in clustering energy with increasing size of the adsorbed Pt clusters indicates that the growth of Pt on this surface will lead to the formation of three-dimensional particles.