N3敏化Ho~（3＋）离子修饰TiO2纳米晶电极的光电化学性质

研究了Ho3+离子表面修饰对TiO2纳米晶电极光电性能的影响.TiO2表面氧化钬的存在一方而降低了染料和TiO2之间的电子注入速率,而另一方面它也能够抑制电荷复合.结果表明,在TiO2纳米晶薄膜表面修饰一定厚度的HO3+离子层,在电极表面就形成了一个势垒,能够有效抑制电极表面的电荷复合,从而提高了染料敏化太阳能电池的光电压和光电转化效率.在93.1 mW·cm-2白光照射下,TiO2/Ho-0.1和TiO2/Ho-0.2(0.1和0.2分别是修饰TjO2电极的Ho3+液的浓度,单位是mol·L-1)两个电极的光电转化效率分别达到8.3%和7.6%,与TiO2电极(7.2%)比较,分别增大了15%和5%.     

染料敏化稀土离子修饰二氧化钛纳米晶电极的光电化学性质

制备了N3染料敏化的稀土离子表面修饰二氧化钛纳米晶电极. 由于在新电极表面形成了一个势垒, 这个势垒可以有效地抑制电极表面的电荷复合, 因此改善了电极的光电转化性质. 其中N3染料敏化Yb³⁺离子修饰TiO₂电极在73.1 mW/cm²白光照射下的光电转化效率比TiO₂电极增大了15%.     

两种菁类染料复合敏化TiO2纳米晶电极的光电化学研究

应用光电化学方法研究了两种菁类染料Cy3和Cy5复合敏化TiO2纳米晶电极的光电化学行为. 结合两种染料的紫外-可见光谱和循环伏安曲线, 确定了Cy3和Cy5的电子基态和激发态能级位置. 结果表明两种染料的激发态能级位置能与TiO2纳米粒子导带边位置相匹配, 复合敏化可以显著提高TiO2纳米晶的光电流, 使TiO2纳米晶电极吸收波长由紫外光区红移至可见光区和近红外区. 复合敏化降低了染料Cy3在电极吸附时的聚集程度, 使其单色光的转换效率(IPCE)提高了169%, 复合敏化电极总的光电转换效率η为2.09%, 分别是Cy3和Cy5单独敏化时光电转换效率的2.069和1.229倍.     

两种菁类染料复合敏化TiO_2纳米晶电极的光电化学研究

应用光电化学方法研究了两种菁类染料Cy3和Cy5复合敏化TiO2纳米晶电极的光电化学行为.结合两种染料的紫外-可见光谱和循环伏安曲线,确定了Cy3和Cy5的电子基态和激发态能级位置.结果表明两种染料的激发态能级位置能与TiO2纳米粒子导带边位置相匹配,复合敏化可以显著提高TiO2纳米晶的光电流,使TiO2纳米晶电极吸收波长由紫外光区红移至可见光区和近红外区.复合敏化降低了染料Cy3 在电极吸附时的聚集程度,使其单色光的转换效率(IPCE)提高了169%,复合敏化电极总的光电转换效率η为2.09%,分别是Cy3和Cy5单独敏化时光电转换效率的2.069 和1.229倍.     

光电化学水氧化用多孔单晶金红石TiO2纳米棒阵列光阳极的设计和构建

光电化学电池(如染料敏化太阳能电池、量子点敏化太阳能电池以及光电化学水分解电池)是实现太阳能转化及存储的有效手段之一.其中,光电极是光电化学电池的核心组成部分,它集光吸收、光生电荷输运及转移等决定光转化效率的关键过程于一身,因此构筑高活性半导体光电极以实现高效太阳能转化利用引起研究者广泛关注.多孔TiO2纳米颗粒堆垛薄膜光阳极因具有大的比表面积,可提供更多的染料(量子点)担载和反应活性位点,在光电化学电池中表现出优异活性而被广泛研究.然而, TiO2纳米颗粒间大量存在的晶界对光生电荷有较强的散射作用,降低了光生电荷的收集效率.英国牛津大学Snaith研究小组利用模板辅助水热过程首次获得了(001)晶面占优的多孔单晶锐钛矿TiO2微米颗粒,这种多孔单晶TiO2微米颗粒在具有大比表面积的同时,其单晶结构还能有效去除晶界对电荷的散射作用,因而具有优异的电荷输运特性.利用这种多孔单晶TiO2微米颗粒组建的光阳极用于染料敏化太阳能电池中,展现出优异的太阳能光电转化性能.受该工作启发,各种形貌的多孔单晶TiO2微米颗粒作为光催化剂和光电化学分解水用光阳极材料被广泛研究,并表现出优异活性.在单晶微米颗粒堆垛成的薄膜光电极中,虽然单个单晶微米颗粒中晶界对电荷的散射作用被有效抑制,但是单晶颗粒间的晶界仍然存在并影响光生电荷的收集效率.为了彻底抑制晶界对光生电荷的散射作用,每个单晶颗粒都应该贯穿整个薄膜,例如一维TiO2纳米棒单晶阵列薄膜.虽然一维单晶阵列薄膜能够有效提高光生电荷的收集效率,但相对于多孔薄膜具有较小的比表面积,限制了担载染料(量子点)和反应位点的数量.为了增大TiO2单晶纳米棒阵列薄膜的比表面积,目前主要的手段包括调控纳米棒长径比、表面修饰TiO2纳米颗粒以及二次生长构建TiO2枝晶阵列.本文首次提出通过制备多孔单晶TiO2纳米棒单晶阵列薄膜来获得高比表面积和高光生电荷收集效率的光阳极,提高光电化学电池的效率.在透明导电薄膜(FTO)表面利用水热生长TiO2纳米棒阵列薄膜之前,预先在FTO基体上沉积一层SiO2球密堆模板, TiO2纳米棒单晶阵列在从FTO表面向上生长过程中,会将SiO2球模板包裹进TiO2纳米棒中,再通过碱溶液将SiO2球模板溶解,首次在FTO基体上原位生长出多孔单晶TiO2纳米棒阵列薄膜.将所得多孔单晶金红石TiO2纳米棒阵列薄膜作为光电化学分解水电池光阳极,其光电化学分解水活性相对于实心单晶金红石TiO2纳米棒阵列提高了2.6倍.多孔单晶金红石TiO2纳米棒阵列光阳极性能的提升可归因于：(1)多孔结构赋予多孔单晶金红石TiO2纳米棒阵列薄膜更大的比表面积,可提供更多的反应活性位点;(2)多孔结构能够有效缩短单晶金红石TiO2纳米棒中光生电荷体相输运距离,提高光生电荷的收集效率;(3)多孔结构通过对光多次反射吸收可有效增强光吸收,产生更多光生电荷参与水分解反应;(4)在制备过程中引入Si掺杂,导致多孔单晶金红石TiO2纳米棒带隙扩大了0.1 eV,带隙增大归因于导带位置负移0.1 eV,光生电子具有更强的还原能力,光电流起始电位相应负移约0.1 V.     

Ru(II)染料与聚3-甲基噻吩复合敏化纳米结构TiO_2电极的光电化学研究

利用光电流作用谱、循环伏安等光电化学方法研究了染料RuL2(SCN)2:2TBA(L=2,2'-bipydine-4,4'-dicarboxylicacid)与聚3-甲基噻吩(P3MT)复合敏化电极的光电化学性质.RuL2(SCN)2:2TBA/P3MT复合敏化TiO2纳米晶多孔膜电极比染料RuL2(SCN)2:2TBA敏化TiO2纳米结构电极的光电转换效率大幅度提高.复合敏化电极中存在p-n异质结有效地抑制了电子的反向复合,减少了电子的损失.     

TiO2与ZnO复合纳米结构电极的光电化学研究

利用尿素加压共沉淀法以Ti(SO4)2与Zn(NO3)2为原料制备了TiO2-ZnO复合纳米粒子, 其纳米结构电极的光电化学研究结果表明, 反应物摩尔比为3∶1, 于530 ℃煅烧制备的复合纳米结构电极的光电转换效率最高. 对吸附染料RuL2(SCN)2∶2TBA的纳米结构TiO2和各种复合纳米粒子的纳米结构电极进行光电研究的结果表明, 染料对各纳米结构电极都起到了敏化作用, 其中也是由反应物摩尔比为3∶1, 于530 ℃煅烧制备的纳米结构电极的光电转换效率最高. 对聚3-甲基噻吩修饰的纳米结构TiO2和摩尔比为3∶1, 于530 ℃煅烧的复合纳米粒子构成的纳米结构电极进行光电性能研究, 结果表明, 聚3-甲基噻吩与半导体纳米粒子之间存在p-n结, 在一定条件下p-n结的存在有利于光生电子/空穴的分离, 从而提高了光电转化效率.     

染料敏化太阳能电池中低染料吸附浓度下的界面电荷复合效应

在保持染料吸附量不变的条件下,通过增加TiO2薄膜厚度来降低染料在TiO2薄膜表面的吸附浓度.研究了染料吸附浓度与染料敏化太阳能电池(DSC)中界面电荷复合效应的关系.研究发现,在低染料吸附浓度下,DSCs中界面电荷复合效应明显降低,并由此使得DSC在薄膜厚度增加时,仍能保持0.72～0.80的高填充因子;在TiO2光电极有效面积由0.25 cm2增大到1 cm2时,总光电转换效率(η)损失由34.7%减少到19.6%.     

聚3-甲基噻吩修饰量子点硫化铅连接TiO2纳米结构膜的光电化学研究

采用原位化学法在纳米结构TiO2电极上制备了量子点PbS(Q-PbS), 并用电化学方法在TiO2/Q-PbS表面聚合3-甲基噻吩[poly(3-Methylthiophene), PMeT]. 研究结果表明, PMeT和Q-PbS单独修饰纳米结构TiO2电极和PMeT修饰Q-PbS连接纳米结构TiO2电极的光电流产生的起始波长都向长波方向移动; 在可见光区光电转换效率均比纳米结构TiO2的光电转换效率提高显著; PMeT与Q-PbS修饰的纳米结构TiO2之间存在p-n异质结. 在一定条件下p-n异质结的存在有利于光生电子/空穴的分离, 提高了光电转换效率.     

TiO2光催化分解水制氢研究进展

综述了近几年改善TiO2光催化分解水制氢的方法措施.向水中添加供电子物质可减少光生电子与空穴的复合,添加碳酸盐或碘化物有利于光生电子与空穴分离;TiO2表面沉积适量的金属颗粒也有利于实现电子和空穴分离,但沉积太多的金属颗粒不但降低TiO2对光的吸收而且还可能成为光生电荷复合的中心;掺杂合适的金属离子通过形成杂质能级可把TiO2的吸光范围至拓宽可见光,掺杂非金属元素使TiO2的带隙(Eg)变窄,从而使TiO2的吸光红移更明显,但掺杂离子有可能成为光生电荷复合的中心;染料敏化或半导体复合有利于实现电荷分离,提高光电转换效率.将多种修饰方法有机结合起来制取氢足目前的一个研究方向,最后分析了未来的研究重点.     

Double-layer coating of SrCO3/TiO2 on nanoporous TiO2 for efficient dye-sensitized solar cells

Surface modification plays a crucial role in improving the efficiency of dye-sensitized solar cells (DSSCs), but the reported surface treatments are in general superior to the untreated TiO(2) but inferior to the typical TiCl(4)-treated TiO(2) in terms of solar cell performance. This work demonstrates a two-step treatment of the nanoporous titania surface with strontium acetate [Sr(OAc)(2)] and TiCl(4) in order, each step followed by sintering. An electronically insulating layer of SrCO(3) is formed on the TiO(2) surface via the Sr(OAc)(2) treatment and then a fresh TiO(2) layer is deposited on top of the SrCO(3) layer via the TiCl(4) treatment, corresponding to a double layer of Sr(OAc)(2)/TiO(2) coated on the TiO(2) surface. As compared to the typical TiCl(4)-treated DSSC, the Sr(OAc)(2)-TiCl(4) treated DSSC improves short-circuit photocurrent (J(sc)) by 17%, open-circuit photovoltage (V(oc)) by 2%, and power conversion efficiency by 20%. These results indicate that the Sr(OAc)(2)-TiCl(4) treatment is better than the often used TiCl(4) treatment for fabrication of efficient DSSCs. Charge density at open circuit and controlled intensity modulated photocurrent/photovoltage spectroscopy reveal that the two electrodes show almost same conduction band level but different electron diffusion coefficient and charge recombination rate constant. Owing to the blocking effect of the SrCO(3) layer on electron recombination with I(3)(-) ions, the charge recombination rate constant of the Sr(OAc)(2)-TiCl(4) treated DSSC is half that of the TiCl(4)-treated DSSC, accounting well for the difference of their V(oc). The improved J(sc) is also attributed to the middle SrCO(3) layer, which increases dye adsorption and may improve charge separation efficiency due to the blocking effect of SrCO(3) on charge recombination.     

The enhanced photoelectric conversion efficiency of N3 sensitized MgTiO3 modified nanoporous TiO2 electrodes

The preparation of nanoporous TiO₂ electrodes modified with an MgTiO₃ layer and its application in dye-sensitized solar cells (DSSCs) were reported. The conduction band of MgTiO₃ stands higher than that of TiO₂, so the MgTiO₃ layer can be beneficial to the improvement of nanoporous TiO₂ electrodes. The as-prepared TiO₂/MgTiO₃ electrodes were characterized by XRD and the diffraction of its crystal plane (1 0 4) was detected, demonstrating the existence of MgTiO₃ phase on the surface of TiO₂. Compared with bare TiO₂ electrodes, MgTiO₃ modified TiO₂ electrodes presented more dye adsorption. Moreover an energy barrier formed as TiO₂ electrodes were modified with MgTiO₃ layer, which suppresses the charge recombination. As a result, the photoelectrochemical properties of the modified electrodes were improved and the overall energy conversion efficiency η was increased from 6.12% to 8.75% under the illumination of a white light of 100 mW/cm².     

表面修饰的TiO_2太阳能电池界面特性研究

用水热法制备了具有典型锐钛矿晶型的TiO2纳米材料,采用Cr(NO3)3对TiO2薄膜电极进行修饰改性。用X射线衍射(XRD)、扫描电子显微镜(SEM)和光电子能谱(XPS)测试电极的物相及表面结构,结果显示TiO2薄膜表面包覆一层粒径较大的氧化铬颗粒,整个电极仍保持均匀的多孔结构。电流-电压(I-V)曲线测试结果显示,改性后最佳电极的短路电流和光电转换效率分别比改性前提高了31.1%和40.4%。用电化学阻抗谱(EIS)测试电池的界面特性,从测试结果可以看出,相同偏压下,改性后电池的TiO2/染料/电解质界面电阻更大,说明氧化铬包覆层在一定程度上抑制了界面的电子复合,改善了电池的光电输出特性。     

Mg(OOCCH(3))(2) as an electrolyte additive for quasi-solid dye-sensitized solar cells: with the purpose of enhancing both the photovoltage and photocurrent by modifying the TiO(2)/dye/electrolyte interfaces

The interface modification effect within quasi-solid dye-sensitized solar cells and the photovoltaic performance were investigated after the introduction of Mg(OOCCH(3))(2) as an additive into a polymer gel electrolyte. Electrochemical impedance spectroscopy showed that the addition of Mg(OOCCH(3))(2) into the polymer gel electrolyte can efficiently retard charge recombination at the TiO(2)/electrolyte interface. Mg(OOCCH(3))(2) in the electrolyte can also contribute to the enhancement of the incident photon-to-electron conversion efficiency by modifying the dye molecules. This results in an improvement in the photovoltage and photocurrent due to a barrier layer at the TiO(2)/electrolyte interface and the promotion of charge injection at the dye/TiO(2) interface, respectively. Photovoltaic measurements reveal that a conversion efficiency enhancement from 4.05% to 4.96% under 100 mW cm(-2) is obtained after the amount of Mg(OOCCH(3))(2) added was optimized.     

Highly conductive nanostructured C-TiO2 electrodes with enhanced electrochemical stability and double layer charge storage capacitance

The present work reports the structural and electrochemical properties of carbon-modified nanostructured TiO(2) electrodes (C-TiO(2)) prepared by anodizing titanium in a fluoride-based electrolyte followed by thermal annealing in an atmosphere of methane and hydrogen in the presence of Fe precursors. The C-TiO(2) nanostructured electrodes are highly conductive and contain more than 1 × 10(10) /cm(2) of nanowires or nanotubes to enhance their double layer charge capacitance and electrochemical stability. Electrogenerated chemiluminescence (ECL) study shows that a C-TiO(2) electrode can replace noble metal electrodes for ultrasensitive ECL detection. Dynamic potential control experiments of redox reactions show that the C-TiO(2) electrode has a broad potential window for a redox reaction. Double layer charging capacitance of the C-TiO(2) electrode is found to be 3 orders of magnitude higher than an ideal planar electrode because of its high surface area and efficient charge collection capability from the nanowire structured surface. The effect of anodization voltage, surface treatment with Fe precursors for carbon modification, the barrier layer between the Ti substrate, and anodized layer on the double layer charging capacitance is studied. Ferrocene carboxylic acid binds covalently to the anodized Ti surface forming a self-assembled monolayer, serving as an ideal precursor layer to yield C-TiO(2) electrodes with better double layer charging performance than the other precursors.     

电极材料对NPB/Alq3有机电致发光器件性能的影响

采用不同材料作为有机电致发光器件(OELDs)的电极, 制备了基本结构为[阳极/NPB(40 nm)]/Alq3(50 nm)/阴极]的异质结双层器件, 并通过改变OELDs器件的阴极或阳极来研究电极材料对器件光电性能的影响. 研究结果表明, 各器件电流-电压(I-V)关系的基本特征与陷阱电荷限制电流(TCLC)机制的拟合情况相符. 由于有机材料本身能级的无序性以及载流子迁移率对温度和电场的依赖性, 不同电极的载流子注入能力与其功函数并无直接关系. 双层器件中由于空穴传输层的引入, 使得载流子复合区域位于有机层异质结界面处, 降低了金属阴极对激子的猝灭作用, 从而大大提高了器件性能. 此外, 金属电极OLEDs器件结构具有的微腔效应会导致发射光谱的位移和谱峰宽度变窄, 这表明通过对金属电极的表面改性和优化可使器件性能超过常规结构的器件.     

The influence of dye structure on charge recombination in dye-sensitized solar cells

Replacing the nonyl groups on the solar cell dye Ru(4,4'-carboxylic acid-2,2'-bipyridine)(4,4'-dinonyl-2,2'-bipyridine)(NCS)(2) (Z-907) with amino groups results in a marked decrease in solar cell performance. This is despite the fact that the amino derivative (Z-960) has more favourable light absorption characteristics than Z-907 when used with thick nanocrystalline TiO(2) layers. Electron transfer to the electrolyte from the exposed fluorine-doped tin oxide (FTO) substrate is particularly fast in cells employing the Z-960 dye if a compact TiO(2) blocking layer is not used. The kinetics of electron transfer from the nanocrystalline TiO(2) layer in DSCs employing Z-960 are comparable to those of bare TiO(2) and ca. 2 to 5 times faster than for cells employing Z-907. The faster charge recombination in cells employing Z-960 lowers open-circuit photovoltage and results in very significant charge collection losses that lower short-circuit photocurrent. Voltammetric measurements show that surface modification of FTO electrodes with Z-960 results in slightly more facile charge transfer to acceptor species in triiodide/iodide electrolytes in the dark. A simpler molecule, p-aminobenzoic acid, more dramatically catalyses this charge transfer reaction. Conversely, chemical modification of FTO electrodes with Z-907 or p-toluic acid retards charge transfer kinetics. Similar results are obtained for nanocrystalline TiO(2) electrodes modified with these benzoic acid derivatives. These results strongly imply that surface adsorbed molecules bearing amino groups, including dye molecules, can catalyse charge recombination in dye-sensitized solar cells.     

Correlating interface heterostructure, charge recombination, and device efficiency of poly(3-hexyl thiophene)/TiO2 nanorod solar cell

The charge recombination rate in poly(3-hexyl thiophene)/TiO(2) nanorod solar cells is demonstrated to correlate to the morphology of the bulk heterojunction (BHJ) and the interfacial properties between poly(3-hexyl thiophene) (P3HT) and TiO(2). The recombination resistance is obtained in P3HT/TiO(2) nanorod devices by impedance spectroscopy. Surface morphology and phase separation of the bulk heterojunction are characterized by atomic force microscopy (AFM). The surface charge of bulk heterojunction is investigated by Kelvin probe force microscopy (KPFM). Lower charge recombination rate and lifetime have been observed for the charge carriers in appropriate heterostructures of hybrid P3HT/TiO(2) nanorod processed via high boiling point solvent and made of high molecular weight P3HT. Additionally, through surface modification on TiO(2) nan,orod, decreased recombination rate and longer charge carrier lifetime are obtained owing to creation of a barrier between the donor phases (P3HT) and the acceptor phases (TiO(2)). The effect of the film morphology of hybrid and interfacial properties on charge carrier recombination finally leads to different outcome of photovoltaic I-V characteristics. The BHJ fabricated from dye-modified TiO(2) blended with P3HT exhibits 2.6 times increase in power conversion efficiency due to the decrease of recombination rate by almost 2 orders of magnitude as compared with the BHJ made with unmodified TiO(2). In addition, the interface heterostructure, charge lifetime, and device efficiency of P3HT/TiO(2) nanorod solar cells are correlated.     

Effects of Metal Oxide Modifications on Photoelectrochemical Properties of Mesoporous TiO2 Nanoparticles Electrodes for Dye-Sensitized Solar Cells

Mesoporous TiO₂ (m-TiO₂) nanoparticles were used to prepare the porous film electrodes for dye-sensitized solar cells, and a second metal oxide (MgO, ZnO, Al₂O₃, or NiO) modifi-cation was carried out by dipping the m-TiO₂ electrode into their respective nitrate solution followed by annealing at 500 oC. Experimental results indicated that the above second metal oxide modifications on m-TiO₂ electrode are shown in all cases to act as barrier layer for the interfacial charge transfer processes, but film electron transport and interfacial charge recombination characteristics under applied bias voltage were dependent significantly on the existing states and kinds of these second metal oxides. Those changes based on sec-ond metal oxide modifications showed good correlation with the current-voltage analyses of dye-sensitized solar cell, and all modifications were found to increase the open-circuit photo-voltage in various degrees, while the MgO, ZnO, and NiO modifications result in 23%, 13%, and 6% improvement in cell conversion efficiency, respectively. The above observations indi-cate that controlling the charge transport and recombination is very important to improve the photovoltaic performance of TiO₂-based solar cell.     

Cathodic electrochemiluminescence at double barrier Al/Al2O3/Al/Al2O3 tunnel emission electrodes

Double insulating barrier tunnel emission electrodes were fabricated by adding a new pure aluminum layer upon oxidized aluminum electrodes by vacuum evaporation and thermally oxidizing the new aluminum layer in air at room temperature. Resulting Al/Al₂O₃/Al/Al₂O₃ electrodes allow the use of various aluminum alloys in the electrode body necessary for hardness or shaping ability of the electrode while obtaining the luminescence properties of pure aluminum oxide. During electrical excitation of luminescent labels by cathodic hot electron injection into aqueous electrolyte solution, the background noise is mainly based on high-field-induced solid-state electroluminescence and F-center luminescence of the outer aluminum oxide film. The more defect states and/or impurity centers the outer oxide film contains, the higher is the background emission intensity. The present electrode fabrication method provides a considerable improvement in signal-to-noise ratio for time-resolved electrochemiluminescence (TR-ECL) measurements when the original native oxide film of the electrode body contains luminescence centers displaying long-lived luminescence. The excellent performance of the present electrodes is demonstrated by extremely low-level detection of Tb(III) chelates, luminol, Pt(II) coproporphyrin and Tb(III) labels in an immunometric immunoassay by time-resolved electrochemiluminescence.