Speciation analysis of arsenic in Mya arenaria Linnaeus and Shrimp with capillary electrophoresis-inductively coupled plasma mass spectrometry

An improved sheath-flow interface used to couple capillary electrophoresis (CE) with inductively coupled plasma mass spectrometry (ICP-MS) and a microwave-assisted extraction used to extract each arsenic species in seafood were developed in this work. The improved sheath-flow interface completely avoids laminar flow in CE capillary caused by the suction from ICP-MS, makes electric supply more stable in CE, and transports analyte solution to ICP-MS easily and more efficiently. CE-ICP-MS coupled with our interface have two quantitative analysis modes: continuous sample-introduction mode and collective sample-introduction mode. The collective sample-introduction technique greatly reduced the dead volume of interface to approximately zero, obviously avoided the excessive dilution of analyte, and eventually led to a much lower detection limit and a much better electrophoretic resolution. This was demonstrated by the better symmetry and narrow peak widths (10-12 s) and much lower detection limits (0.030-0.042 μg/L) of four species of arsenic determined with collective sample-introduction mode.With the help of this improved sheath-flow interface and the microwave-assisted extraction, we have successfully separated and determined four arsenic species, As(III), As(V), monomethylarsonic acid (MMA) and dimethylarsinic acid (DMA) in dried Mya arenaria Linnaeus and Shrimp samples using CE-ICP-MS within 10 min with a relative standard deviation of 2-4% (peak areas, n = 6) and a recovery of 96-105%.     

Quantification of phosphorus in DNA using capillary electrophoresis hyphenated with inductively coupled plasma mass spectrometry

We have analyzed phosphorus in an enzymatically digested DNA molecule using capillary electrophoresis (CE) hyphenated with inductively coupled plasma mass spectrometry (ICP-MS). The DNA concentration was quantified by the phosphorus value obtained in the CE-ICP-MS analysis. The CE-ICP-MS measurement, for which the interface device AIF-01 equipped three layered nebulizer was adopted, was achieved with limited μL/min nebulizing without loss of sample in the vaporizing chamber. The samples of nucleotides and free phosphate were separated well in the CE-ICP-MS measurement, and the calibration curve (0.1-10μg/mL) of the phosphorus showed a linear (R(2)=0.999) increase in intensity. After digestion of the 100-bp double-strand DNA sample to deoxyribonucleotide-5'-monophosphates (dNMPs) by phosphodiesterase-I, phosphorus was detected by CE-ICP-MS without further purification steps. In this study, we applied two calculation schemes of DNA analysis using a dNMP concentration obtained from CE-ICP-MS. Comparative CE-ICP-MS analysis with DNA digested to dNMPs showed that the assay gave an equal value obtained from the total DNA quantification using fluorescence detection. The detection limits of the DNA sample obtained from these species and phosphorus in nucleotides using CE-ICP-MS were 3.1-26ng/mL. These LOD values were equal to the conventional fluorescence determination of DNA.     

Hyphenated techniques for the characterization and quantification of metallothionein isoforms

Recent developments in the coupling of highly selective separation techniques such as capillary electrophoresis (CE) and high-performance liquid chromatography (HPLC) to element-specific and molecule-specific detectors, such as inductively-coupled plasma mass spectrometry (ICP-MS) and electrospray ionization-tandem mass spectrometry (ESI-MS/MS) for the characterization and quantification of metallothioneins (MTs) are critically reviewed and discussed. This review gives an update based on the literature over the last five years. The coupling of CE to ICP-MS is especially highlighted. As a result of progress in new interface technologies for CE-ICP-MS, research topics presented in the literature are changing from "the characterization of interfaces by metallothioneins" to the "characterization of metallothioneins by CE-ICP-MS". New applications of CE-ICP-MS to the analysis of MTs in real samples are summarized. The potential of the on-line isotope dilution technique for the quantification of MTs and for the determination of the stoichiometric composition of metalloprotein complexes is discussed. Furthermore, a selection of relevant papers dealing with HPLC-ICP-MS for MT analysis are summarized and compared to those dealing with CE-ICP-MS. In particular, the use of size-exclusion (SE)-HPLC as a preliminary separation step for metallothioneins in real samples prior to further chromatographic or electrophoretic separations is considered. Additionally, the application of electrospray ionisation-tandem mass spectrometry (ESI-MS/MS) for the identification of metallothionein isoforms following electrophoretic or chromatographic separation is discussed.     

Short-column CE coupled with inductively coupled plasma MS for high-throughput speciation analysis of chromium

A method was developed for high-throughput speciation analysis of chromium by on-line coupling of short-column capillary electrophoresis (SC-CE) and inductively coupled plasma mass spectrometry (ICP-MS). Baseline separation of Cr(III) and Cr(VI) was achieved within 1 min by SC-CE in a 15 cm x 75 microm id fused-silica capillary at 6 kV using 15 mM HNO(3) as running electrolyte. The precisions (RSD, n = 5) of migration time and peak area for Cr(III) and Cr(VI) were in the range of 1.8-2.4% and 2.2-5.7%, respectively. The limits of detection (3sigma) of Cr(III) and Cr(VI) were 1.8 and 1.9 microg/L, respectively. The synthesized samples containing Cr(III) and Cr(VI) species were determined by the developed SC-CE-ICP-MS hyphenated technique, and the recoveries of Cr(III) and Cr(VI) in the synthesized samples were in the range of 103-110% and 90-108%, respectively.     

Fraction collection in capillary electrophoresis for various stand-alone mass spectrometers

A procedure for collecting fractions during capillary electrophoresis for their analysis using various stand-alone instruments is described. The results of a systematic study of the optimization and application of capillary electrophoresis (CE) in conjunction with a reverse-phase high-performance liquid chromatography electrospray ionization quadrupole time of flight-tandem mass spectrometry (RP-HPLC-ESI-Q-TOF-MS/MS) and inductively-coupled mass spectrometry (ICP-MS) to the analysis of the seed extract of the Japanese Pagoda Tree (Sophora japonica) are presented. The off-line coupling of CE to the matrix-assisted laser desorption/ionization-time of flight mass spectrometry (MALDI-TOF-MS) for the proteins mixture was applied. The cathode end of the capillary was placed inside a stainless steel needle using a coaxial liquid-sheath-flow configuration. The optimization of experimental parameters resulted in an efficient methodology for MS analysis of fractions. Several components contained in the extract of S. japonica were identified, some not previously known. It was demonstrated that low sensitivity, which is a real problem in off-line CE–MS analysis, could be tolerated because of a more flexible optimization of the CE separation conditions and the choice of independent stand-alone instruments for analysis of separated fractions. The estimated limit of detection for CE-RP-HPLC-ESI-Q-TOF-MS was 50 μM of polyphenols and for CE-ICP-MS, 1–100 μg/l.     

The potential and challenges of elemental speciation by capillary electrophoresis-inductively coupled plasma mass spectrometry and electrospray or ion spray mass spectrometry

Capillary electrophoresis-inductively coupled plasma mass spectrometry (CE-ICP-MS) and electrospray (ES) or ion spray (IS) mass spectrometry (MS) are recently introduced techniques for elemental speciation. Both techniques have the potential for rapid elemental speciation with low detection limits. Examples of the use of CE-ICP-MS for elemental speciation of positive, neutral and negative species are discussed. Issues in interfacing CE and ICP-MS are considered briefly. The potential advantages and disadvantages of laminar flow in CE-ICP-MS are examined. Potential difficulties in CE-ICP-MS including loss of sample, chemical matrix effects and changes in speciation during separation are discussed. The interpretation of ES or IS-MS spectra and analysis of complex mixtures are considered. Calibration and chemical matrix effects are assessed. Potential pitfalls of interpreting bare metal ion spectra as elemental analysis are discussed. The need for fundamental understanding of the processes that control ES and IS-MS signals is examined. High conductivity samples currently present difficulties for CE-ICP-MS or ES and IS-MS.     

毛细管电泳-电感耦合等离子体质谱法测定藻类中6种不同形态的砷化合物

建立了一种利用毛细管电泳与电感耦合等离子体质谱联用技术(CE-ICP-MS)分析检测6种不同形态砷化合物的方法。详细研究了缓冲溶液的种类、pH值和浓度,分离电压以及进样时间等因素对6种砷化合物的分离度、灵敏度和重现性等的影响。结果表明,在最佳条件下,三价砷(As3+)、一甲基砷(MMA)、二甲基砷(DMA)、五价砷(As5+)、砷胆碱(AsC)和砷甜菜碱(AsB)6种化合物在25 min内得到完全分离。6次平行测定中,6种砷化合物峰面积的相对标准偏差(RSD)为3%～5%,检出限(以As计)(3倍信噪比)为0.08～0.12 μg/L。应用该方法成功地对海带中6种砷化合物进行了分析,回收率为90%～103%。该方法具有耗时短、灵敏度高、样品消耗量少、稳定性好等优点,可用于藻类样品中不同形态砷化合物的分析。     

Speciation of chromium (III) and chromium (VI) by capillary electrophoresis with contactless conductometric detection and dual opposite end injection

A sensitive, rapid and inexpensive capillary electrophoretic method for the determination of Cr(III) and Cr(VI) species is presented. The method is based on the dual opposite end injection principle and contactless conductometric detection. The sample containing cationic and anionic species is injected into the opposite ends of the separation capillary and after the high voltage is applied, the analytes migrate towards the capillary center, where the cell of a contactless conductivity detector is placed. The method does not require any sample pretreatment, except dilution with deionized water. The separation of Cr(III), Cr(VI) and other common inorganic anions and cations is achieved in less than 4 min. The parameters of the separation electrolyte solution, such as pH and concentration of L-histidine, were optimized. Best results were achieved with electrolyte solution consisting of 4.5 mM L-histidine, adjusted to pH 3.40 with acetic acid. The detection limits achieved for Cr(III) and Cr(VI) were 10 and 39 microg.L(-1), respectively. The repeatability of migration times and peak areas was better than 0.3% and 2.8%, respectively. The developed method was applied to the analyses of rinse water samples from the galvanic industry. The results for the determination of Cr(III) and Cr(VI) were in good agreement with the results obtained by certified differential spectrophotometric method using diphenylcarbazide (CN 83 0520-40) and with the results for the total chromium concentrations determined by electrothermal atomic absorbance spectrometry (ET-AAS) and inductively coupled plasma-mass spectrometry (ICP-MS).     

CE-ICP-MS for studying interactions between metals and biomolecules

Metal-biomolecule interactions comprise an important research area in metallomics, and are significant for biology, medicine, pharmacy, nutrition, metabolism, and environmental science. Hybrid techniques are preferred for studying interactions between metals and biomolecules. Of all the separation techniques, capillary electrophoresis (CE) exhibits high resolution, minimal sample and reagent consumption, and rapid and efficient separations with minor disturbance of the existing equilibrium between the metal species and their biomolecular complexes. Inductively coupled plasma mass spectrometry (ICP-MS) presents high sensitivity to most of elements and offers multi-element detection.This article provides an overview of CE-ICP-MS for the study of metal-biomolecule interactions. We discuss applications of CE-ICP-MS to the study of interactions between metals or metalloids and natural ligands, such as humic substances or fulvic acids, and the interchange of metal complexes with metal species in metalloproteins.     

Complexation studies with lanthanides and humic acid analyzed by ultrafiltration and capillary electrophoresis-inductively coupled plasma mass spectrometry

For the long-term storage of radioactive waste, detailed information about geo-chemical behavior of radioactive and toxic metal ions under environmental conditions is necessary. Humic acid (HA) can play an important role in the immobilisation or mobilisation of metal ions due to complexation and colloid formation. Therefore, we investigate the complexation behavior of HA and its influence on the migration or retardation of selected lanthanides (europium and gadolinium as homologues of the actinides americium and curium). Two independent speciation techniques, ultrafiltration and capillary electrophoresis coupled with inductively coupled plasma mass spectrometry (CE-ICP-MS) have been compared for the study of Eu and Gd interaction with (purified Aldrich) HA. The degree of complexation of Eu and Gd in 25 mg l(-1) Aldrich HA solutions was determined with a broad range of metal loading (Eu and Gd total concentration between 10(-6) and 10(-4) mol l(-1)), ionic strength of 10 mM (NaClO4) and different pH-values. From the CE-ICP-MS electropherograms, additional information on the charge of the Eu species was obtained by the use of 1-bromopropane as neutral marker. To detect HA in the ICP-MS and separate between HA complexed and non complexed metal ions in the CE-ICP-MS, we have halogenated the HA with iodine as ICP-MS marker.     

Investigation of a liposomal oxaliplatin drug formulation by capillary electrophoresis hyphenated to inductively coupled plasma mass spectrometry (CE-ICP-MS)

A capillary electrophoresis-inductively coupled plasma mass spectrometry (CE-ICP-MS) method was developed for separation of the free oxaliplatin drug substance from liposome-entrapped oxaliplatin. Simultaneous determination of phosphorous and platinum opened the possibility to simultaneously monitor the liposomes (phospholipids) and platinum-based drug. In order to suppress the interferences, argon gas was used as a collision gas in ICP-MS. A detection limit of 29 ng/mL of platinum and a precision of 2.9% (for 10 μg/mL of oxaliplatin standard) were obtained. Measurement of the total concentration of free and encapsulated oxaliplatin by CE-ICP-MS was compared with total determination by ICP-MS after microwave digestion and showed a good agreement. A liposomal formulation of oxaliplatin based on PEGylated liposomes was used as a model drug formulation. Studies of accelerated drug release induced by sonication and phospholipase A₂ catalyzed hydrolysis were performed. It was demonstrated that the CE-ICP-MS was an efficient in vitro characterization method in the development and quality assurance purposes of lipsome-based formulation of metallodrugs.     

Thermodynamical and structural study of protactinium(V) oxalate complexes in solution

The complexation of protactinium(V) by oxalate was studied by X-ray absorption spectroscopy (XAS), density functional theory (DFT) calculations, capillary electrophoresis coupled with inductively coupled plasma mass spectrometry (CE-ICP-MS) and solvent extraction. XAS measurements showed unambiguously the presence of a short single oxo-bond, and the deduced structure agrees with theoretical calculations. CE-ICP-MS results indicated the formation of a highly charged anionic complex. The formation constants of PaO(C(2)O(4))(+), PaO(C(2)O(4))(2)(-), and PaO(C(2)O(4))(3)(3-) were determined from solvent extraction data by using protactinium at tracer scale (C(Pa) < 10(-10) M). Complexation reactions of Pa(V) with oxalate were found to be exothermic with relatively high positive entropic variation.     

Determination of monophosphate nucleotides by capillary electrophoresis inductively coupled plasma mass spectrometry

A preliminary study of a modified microconcentric nebulizer (CEI-100, CETAC) as the sample introduction device of capillary electrophoresis inductively coupled plasma mass spectrometry (CE-ICP-MS) for the determination of monophosphate nucleotides is described. The monophosphate nucleotides studied include adenosine 5'-monophosphate (AMP), guanosine 5'-monophosphate (GMP), uridine 5'-monophosphate (UMP) and inosine 5'-monophosphate (IMP). The species studied were well separated using a 70 cm length x 75 microm id fused silica capillary while the applied voltage was set at -22 kV and a 20 mmol l(-1) ammonium citrate/citric acid buffer (pH 4.0) containing 0.1% m/v cationic polymer (hexadimethrine bromide, Polybrene) was used as the electrophoretic buffer. The electroosmotic flow was reversed by flushing the fused silica capillary with 0.2% m/v Polybrene to accelerate separation. The detection limit of various species studied was in the range of 0.036-0.054 microg P ml(-1), which corresponded to the absolute detection limit of 1.1-1.6 pg P based on the injection volume of 30 nl. We determined the concentrations of nucleotides in two IG-enriched monosodium glutamates purchased from the local market. The recovery was in the range of 100-112% for various species, and the concentrations of IMP and GMP in these samples were in the range of 0.15-0.18% m/m.     

Capillary electrophoresis hyphenated to inductively coupled plasma-sector field-mass spectrometry for the detection of chromium species after incubation of chromium in simulated sweat

The presence of chromium in chromium-tanned leather represents a considerable health problem since it can lead to chronic allergic contact dermatitis. Apart from trivalent chromium (Cr(III)), which is used for tanning, leather often contains hexavalent chromium (Cr(VI)), resulting from the oxidation of Cr(III) during the tanning process. This study deals with the chromium compounds in simulated sweat when brought into contact with Cr(III) or Cr(VI) and with chromium-tanned leathers. A capillary electrophoresis (CE) method was developed, with inductively coupled plasma-sector field-mass spectrometry (ICP-SF-MS) for element-specific detection. Two different electrophoretic runs, applying once the positive and once the negative polarity mode, were necessary for the detection of positively and negatively charged chromium species. Although sometimes described in the literature, a pre-run derivatization of the chromium-species was not performed here to prevent species transformation. 50 mmol.L(-1) sodium phosphate at a pH of 2.5 was used as CE separation buffer and as make-up liquid for the CE-ICP-SF-MS interface. When applied to simulated sweat samples incubated with Cr(VI), this method showed that methionine is responsible for the reduction of Cr(VI) into Cr(III), which, at its turn, forms a complex with lactic acid. In the case of sweat plus Cr(III), the latter step was also seen. Applied to simulated sweat in contact with leather samples, the method developed showed the presence of the former species among a much more complex pattern.     

毛细管电泳-电感耦合等离子体质谱在痕量元素形态分析中的应用

叙述了元素形态分析的目的和意义以及发展概况，并在此基础上着重叙述了近年来毛细管电泳(CE)与电感耦合等离子体质谱(ICP-MS)联用技术在痕量元素形态分析上的应用，包括该联用技术的关键CE与ICP-MS接口的不同设计，影响CE分离分辨率及分析灵敏度的主要因素。对这种分析技术在元素形态分析上应用的潜力和限制以及发展趋势作了讨论。     

Optimization of the hyphenation between capillary zone electrophoresis and inductively coupled plasma mass spectrometry for the measurement of As-, Sb-, Se- and Te-species,applicable to soil extracts

The optimization of the hyphenation between capillary zone electrophoresis (CZE) and inductively coupled plasma mass spectrometry (ICP-MS) was studied for the simultaneous determination of metalloid species in the environment. Arsenic (arsenite, arsenate, monomethylarsonic acid, dimethylarsinic acid), selenium (selenite, selenate, selenomethionine, selenocystine), antimony (antimonate) and tellurium (tellurite, tellurate) species were simultaneously separated using a 75-μm i.d. fused silica capillary using either a chromate or a phosphate electrolyte. Different nebulizers were tested for introduction in the detector. A V-groove nebulizer (the Babington) and two concentric micronebulizers (the MCN-100 and the MicroMist) were studied in order to improve resolution, sensitivity and reproducibility. The optimization of CE-ICP-MS interface operating parameters is discussed for each nebulizer–interface combination, and special attention is given to the position of the capillary inside the nebulizer. Different nebulizer gas and liquid sheath flow rates were studied in detail and they hardly affect electrophoretic resolution and peak width. The best analytical performance characteristics were obtained with the MicroMist nebulizer. Detection limits with this nebulizer were found to range between 6 and 58 μg l⁻¹ depending on the species investigated using pressure injection and below 1 μg l⁻¹ for most of the species with electromigrative injection. Analysis of soil extracts showed that it was possible to carry out this technique on real samples.     

Determination of cobalamins using capillary electrophoresis inductively coupled plasma mass spectrometry

The determination of cobalamins using capillary electrophoresis inductively coupled plasma mass spectrometry (CE-ICP-MS) was investigated. Both capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC) modes of operation were studied. The optimal separation of four cobalamin species (cyanocobalamin, hydroxocobalamin, methylcobalamin, and 5′-deoxyadenosylcobalamin) and a potentially harmful corrinoid analogue (cobinamide dicyanide) was obtained using CZE at a pH of 2.5. Both 20 mM phosphate and 20 mM formate buffers were used with success, although the formate buffer provided improved resolution. The CZE-ICP-MS method was used to quantify cyanocobalamin in a vitamin supplement and the analytical results were in good agreement (±5%) with values obtained by ICP-MS for total Co levels. The solution detection limits for cobalamins using CZE-ICP-MS were approximately 50 ng/ml. MEKC was found to be useful for the screening of vitamin preparations because it provided a rapid means of distinguishing cyanocobalamin (the form most commonly used in vitamin preparations) from free cobalt. The separation of free cobalt and cyanocobalamin using MEKC was achieved in less than 10 min.     

Capillary electrophoresis-inductively coupled plasma mass spectrometry interface with minimised dead volume for high separation efficiency

A modified microconcentric nebulizer (MCN-100) has been used to construct an improved interface with minimised liquid and gas phase dead volumes for the coupling of capillary electrophoresis (CE) and inductively coupled plasma mass spectrometry (ICP-MS). A plate number of 3.6 x 10(6) plates m(-1) has been achieved. This is an order of magnitude better than the results previously reported for CE-ICP-MS. The separation efficiency of the system is demonstrated by the baseline separation of eight rare earth metals within a time span of 14.6 s. The system was used to control the purity of vitamin B12 and glutaredoxin 2 from Escherichia coli.     

Identification of a metallothionein in Synechococcus by capillary electrophoresis hyphenated with inductively coupled plasma mass spectrometry.

A home-made system hyphenating capillary electrophoresis with an inductively coupled plasma mass spectrometer (CE-ICP-MS) for cadmium speciation of protein-binding and free cadmium ions in solution is presented. The CE-ICP-MS interface consisted of an acrylic block with an internal volume ca. 20 microL in which a platinum electrode, a capillary column, and a connection to an ICP nebulizer were inserted. A make-up electrolyte solution containing 50 mmol L(-1) Tris-HCl buffer solution (pH 9.0) was continuously flowed through the interface to the ICP nebulizer. The separation of free Cd ions, Cd-cysteine, and Cd bounded to metallothionein (MT) isoforms from rabbit liver was carried out by capillary electrophoresis, and the analytes were detected by ICP-MS. The feasibility to isolate metallothionein compounds extracted from the cyanobacterium Synechococcus PCC7942 was demonstrated. The Cd binding proteins were induced in Synechococcus PCC7942 and further analyzed by CE ICP-MS.     

Speciation of arsenic compounds in fish and oyster tissues by capillary electrophoresis-inductively coupled plasma-mass spectrometry

A capillary electrophoresis-inductively coupled plasma-mass spectrometric (CE-ICP-MS) method for the speciation of six arsenic compounds, namely arsenite [As(III)], arsenate [As(V)], monomethylarsonic acid, dimethylarsinic acid, arsenobetaine and arsenocholine is described. The separation has been achieved on a 70 cm length x 75 microm ID fused-silica capillary. The electrophoretic buffer used was 15 mM Tris (pH 9.0) containing 15 mM sodium dodecyl sulfate (SDS), while the applied voltage was set at +22 kV. The arsenic species in biological tissues were extracted into 80% v/v methanol-water mixture, put in a closed centrifuge tube and kept in a water bath, using microwaves at 80 degrees C for 3 min. The extraction efficiencies of individual arsenic species added to the sample at 0.5 microg As/g level were between 96% and 107%, except for As(III), for which it was 89% and 77% for oyster and fish samples, respectively. The detection limits of the species studied were in the range 0.3-0.5 ng As/mL. The procedure has been applied for the speciation analysis of two reference materials, namely dogfish muscle tissue (NRCC DORM-2) and oyster tissue (NIST SRM 1566a), and two real-world samples.