流动注射化学发光法测定甲氨蝶呤

研究了甲醛增强高锰酸钾与甲氨蝶呤的化学发光反应，由此建立了一种测定甲氨蝶呤的流动性注射化学发光分析法，方法的检出限为３．４×１０＾－９ｇ／ｍＬ，相对标准偏差为１．１％（２．０×１０＾－６ｇ／ｍＬ甲氨蝶呤，ｎ＝１１）线性范围为１．０×１０＾－８～１．０×１０＾－５ｇ／ｍＬ。该法已用于甲氨蝶呤针剂及片剂中甲氨蝶呤含量的测定。     

流动注射化学发光法测定尿酸

在碱性条件下,铁氰化钾氧化鲁米诺,产生化学发光,尿酸对该体系的化学发光有显著的增强作用（亚铁氰化钾存在时）。基于此,建立了一种直接测定尿酸的流动注射化学发光分析法。方法的线性范围为２．０×１０－８～５．０×１０－６　ｇ／ｍＬ;检测限（３σ）为６．７×１０－９　ｇ／ｍＬ;相对标准偏差为１．１％（尿酸１．０×１０－７　ｇ／ｍＬ,ｎ＝１１）。用于血清及尿样中尿酸的分析,结果令人满意。     

新化学发光试剂ITCI的合成及其性能研究

合成一种新化学发光试剂异硫氰酸异鲁米诺（ＩＴＣＩ），研究其化学发光及标记酵母ＲＮＡ的性能。标记反应条件温和快速，１克酵母ＲＮＡ可与１．５×１０－５ｍｏｌＩＴＣＩ结合。建立了测定ＩＴＣＩ和ＲＮＡ的化学发光分析方法，线性范围分别为１．０×１０－１０～１．０×１０－７ｍｏｌ／Ｌ和４．０～×１０－９～２．０×１０－７ｇ／ｍＬ，检测限分别为６．６×１０－１１ｍｏｌ／Ｌ和８．０×１０－１０ｇ／ｍＬ。     

偶合反应化学发光法测定痕量银的研究——K4Fe（CN）6—Luminol体系

将Ａｇ（Ｉ）催化Ｋ４Ｆｅ（ＣＮ）６的水合反应与Ｌｕｍｉｎｏｌ同Ｃｕ（ＣＮ）＾２－４的化学发光反应相偶合，建立起一种新的灵敏测定痕量银的化学发光分析法，在所研究的优化条件下，该法测定银的选择性较好，检测限达到４．０×１０＾－１３ｇ／ｍＬＡｇ线性浓度范围为１．０×１０＾－１２～１．０×１０＾－６ｇ／ｍＬＡｇ对４×１０＾－１１ｇ／ｍＬＡｇ（Ｉ）溶液连续１１次测定的ＲＳＤ≤３．５％，用于环境水和岩矿中银的     

高锰酸钾-乙二醛-丙米嗪化学发光体系的研究

在酸性溶液中,高锰酸钾能氧化丙米嗪发生化学发光反应,乙二醛的存在可使发光强度增强。据此,采用流动注射技术,建立了一种测定丙米嗪的化学发光分析法。方法的检出限为１．２×１０－８ｇ／ｍＬ,相对标准偏差为２．７％（２．０×１０－７ｇ／ｍＬ,ｎ＝１１）,线性范围为４．０×１０－８～１．０×１０－６ｇ／ｍＬ。该法已用于丙米嗪片剂中丙米嗪含量的测定,并与药典标准方法进行了对照。     

高锰酸钾-亚硫酸钠-核黄素化学发光体系的研究

研究了核黄素在酸性条件下与高锰酸钾和亚硫酸钠发生化学发光反应的行为,建立了流动注射化学发光测定核黄素的新方法。核黄素浓度在１．０×１０＾－７－１．０×１０＾－５ｇ／ｍＬ范围内与化学发光强度呈良好的线性关系,检出限为３×１０＾－８ｇ／ｍＬ。对４．。０×１０＾－７ｇ／ｍＬ的核黄素进行１１次平行测定,得方法的相对标准偏差为１．６％。     

流动注射化学发光法测定痕量硫

基于硫离子对鲁米诺－过氧化氢化学发光反应的增敏作用,建立了测定痕量硫的流动注射化学发光反应的增敏作用,建立了测定痕量硫的流动注射化学发光的新方法。该方法的线性范围为２．０×１０－９～８．０×１０－７ｇ／ｍＬ,检出限为５．６×１０－１０ｇ／ｍＬ,相对标准偏差小于５％（１．０×１０－７ｇ／ｍＬＳ２－,ｎ＝１１）。方法简单,快速,灵敏,已用于环境水样中痕量硫的测定。     

流动注射化学发光法测定利血平

研究了利血平在酸性条件下与高锰酸钾和过氧化氢产生化学发光的行为，建立了流动注射化学发光测定利血平的新方法。利血平的浓度在１．０×１０＾－６￣８．０×１０＾－５ｈ／ｍＬ范围内与化学发光强度呈良好的线性关系；检出限为３×１０＾－７ｇ／ｍＬ。对６×１０＾－６ｇ／ｍＬ利血平进行１１次平行测定，得方法的相对标准偏差为１．３％。方法用于药剂中利血平含量测定，结果与药典标准方法测得值一致。     

流动注射化学发光法测定安痛定注射液中的氨基比林

在甲醛存在下,高锰酸钾与氨基比林能够发生化学发光反应,产生很强的化学发光,由此建立一种测定氨基比林的流动注射化学发光分析法。方法的检出限为３．０×１０－８ｇ／ｍＬ,相对标准偏差为１．３％（４．０×１０－５ｇ／ｍＬ氨基比林,ｎ＝１１）,线性范围为１．０×１０－７～８．０×１０－５ｇ／ｍＬ氨基比林。该法已用于安痛定注射液中氨基比林含量的测定。     

流动注射化学发光法测定盐酸异丙嗪

在酸性溶液中，高锰酸钾能氧化盐酸异丙嗪产生化学发光反应，乙二醛的存在可使发光强度增强。据此，采用流动注射技术，建立了一种测定盐酸异丙嗪的化学发光分析分析。方法的检出限为３．５×１０＾－８ｇ／ｍＬ，相对标准偏差为２．８％（１．０×１０＾－６ｇ／ｍＬ盐酸异丙嗪，ｎ＝１１），线性范围为１．０×１０＾－７￣６．０×１０＾－５ｇ／ｍＬ。该法已用于盐酸异丙嗪针剂和片剂中盐酸异丙嗪含量的测定，并与药典标准方法进     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.