Calculation of the pressure on the side surface of bodies consisting of a spherical segment joined to an inverted cone in a supersonic stream

The results of investigations of inviscid flow over inverted cones with nose consisting of a spherical segment were published for the first time in Soviet literature in [1–4]. In the present paper, a numerical solution to this problem is obtained using the improved algorithms of [5, 6], which have proved themselves well in problems of exterior flow over surfaces with positive angles of inclination to the oncoming flow. It is shown that the Mach number 2 M , equilibrium and nonequilibrium physicochemical transformations in air (H = 60 km, V = 7.4 km/sec, R₀ = 1 m), and the angle of attack 0 40° influence the investigated pressure distributions. A comparison of the results of the calculations with drainage experiments for M = 6, = 0-25° confirms the extended region of applicability of the developed numerical methods. Also proposed is a simple correlation of the dependence on the Mach number in the range 1.5 M of the shape of the shock wave near a sphere in a stream of ideal gas with adiabatic exponent = 1.4.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 178–183, January–February, 1981.     

Effect of suspended particles on the stability of plane poiseuille flow

The behavior of the neutral stability curves is investigated for various values of the particle relaxation time and mass concentration 0 100 and 0 f 0.1. It is shown that as increases from zero the flow is at first destabilized and then at >6 becomes stable, while at >40 the stabilizing effect of the dispersed phase grows weaker. It is found that there is a certain interval 10< <40 on which the flow is most stable.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 46–53, January–February, 1986.     

Normal forms for random diffeomorphisms

Given a dynamical system (,, ,) and a random diffeomorphism (): ^{d d} with fixed point at x=0. The normal form problem is to construct a smooth near-identity nonlinear random coordinate transformation h() to make the random diffeomorphism ()=h()^–1() h() as simple as possible, preferably linear. The linearization D(, 0)=:A() generates a matrix cocycle for which the multiplicative ergodic theorem holds, providing us with stochastic analogues of eigenvalues (Lyapunov exponents) and eigenspaces. Now the development runs pretty much parallel to the deterministic one, the difference being that the appearance of turns all problems into infinite-dimensional ones. In particular, the range of the homological operator is in general not closed, making the conceptof-normal form necessary. The stochastic versions of resonance and averaging are developed. The case of simple Lyapunov spectrum is treated in detail.     

Hypersonic flow past blunt-edged delta wings

A method is proposed for calculating hypersonic ideal-gas flow past blunt-edged delta wings with aspect ratios = 100–200. Systematic wing flow calculations are carried out on the intervals 6 M 20, 0 20, 60 80; the results are analyzed in terms of hypersonic similarity parameters.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 175–179, September–October, 1990.     

Two-dimensional transonic vortex flows of an ideal gas

Equations are obtained for two-dimensional transonic adiabatic (nonisoenergetic and nonisoentropic) vortex flows of an ideal gas, using the natural coordinates (=const is the family of streamlines, and =const is the family of lines orthogonal to them). It is not required that the transonic gas flow be close to a uniform sonic flow (the derivation is given without estimates). Solutions are found for equations describing vortex flows inside a Laval nozzle and near the sonic boundary of a free stream.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 105–109, September–October, 1973.     

Transport in ordered and disordered porous media I: The cellular average and the use of weighting functions

In this work we consider transport in ordered and disordered porous media using singlephase flow in rigid porous mediaas an example. We defineorder anddisorder in terms of geometrical integrals that arise naturally in the method of volume averaging, and we show that dependent variables for ordered media must generally be defined in terms of thecellular average. The cellular average can be constructed by means of a weighting function, thus transport processes in both ordered and disordered media can be treated with a single theory based on weighted averages. Part I provides some basic ideas associated with ordered and disordered media, weighted averages, and the theory of distributions. In Part II a generalized averaging procedure is presented and in Part III the closure problem is developed and the theory is compared with experiment. Parts IV and V provide some geometrical results for computer generated porous media.Roman Letters A interfacial area of the- interface contained within the macroscopic region, m² - A_e area of entrances and exits for the-phase contained within the macroscopic system, m² - g gravity vector, m/s² - I unit tensor - K traditional Darcy's law permeability tensor, m² - L general characteristic length for volume averaged quantities, m - characteristic length (pore scale) for the-phase - (y) weighting function - m(–y) (y), convolution product weighting function - _v special weighting function associated with the traditional averaging volume - N unit normal vector pointing from the-phase toward the-phase - p pressure in the-phase, N/m² - p0 reference pressure in the-phase, N/m² - p traditional intrinsic volume averaged pressure, N/m² - r0 radius of a spherical averaging volume, m - r position vector, m - r position vector locating points in the-phase, m - averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - v velocity vector in the-phase, m/s - v traditional superficial volume averaged velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V/V, volume average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m²     

Numerical investigation of laminar separation in the case of supersonic flow of viscous gas past spiked bodies

The complete Navier-Stokes equations for a compressible viscous perfect heat conducting gas have been used in a numerical investigation of laminar separation in the case of supersymmetric axisymmetric flow past cylinders with a conical nose and a spike at the front of finite thickness. The flow structure has been studied in its dependence on the length of the spike and the half-angle of the conical tip. For the considered free-stream parameters (2 M 6, 100 Re 500) and spike lengths, which do not exceed the diameter of the cylinder, the existence of steady flow regimes has been established and it has been shown that the spike in front of the body reduces its total drag and the heat flux to its surface.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 126–131, March–April, 1984.     

Impulsive motion of a semi-infinite flat plate in a viscous fluid

The unsteady laminar boundary layer flow is investigated for a semi-infinite flat plate subjected to impulsive motion. An approximate solution is obtained by utilizing Meksyn's method. These results vary smoothly from Rayleigh's unsteady solution to the steady state solution of Blasius. Results are compared to those of Lam and Crocco.Nomenclature A expansion coefficient, see eq. (13) - a expansion coefficient, see eq. (10) - B expansion coefficient, see eq. (14) - b expansion coefficient, see eq. (12) - G function defined by eq. (6) - U free stream velocity - u velocity in x direction - v velocity in y direction - x coordinate along plate - y coordinate normal to plate Greek symbols (l, ) incomplete gamma function - function defined by eq. (15) - y(U/x) ^1/2 - kinematic viscosity - x/Ut - (Uvx)^1/2 f(, )     

On surface waves in generalized thermoelasticity

Knowles' representation theorem for harmonically time-dependent free surface waves on a homogeneous, isotropic elastic half-space is extended to include harmonically time-dependent free processes for thermoelastic surface waves in generalized thermoelasticity of Lord and Shulman and of Green and Lindsay.r , , r , , .This work was done when author was unemployed.     

On the measurement of lateral velocity derivatives in turbulent flows

Direct numerical simulation data for the lateral velocity derivative u/y at the centreline of a fully developed turbulent channel flow provide reasonable support for Wyngaard's analysis of the error involved in measuring this quantity using parallel hot wires. Numerical data in the wall region of the channel flow also provide a useful indication of how to select the separation between the wires. Justification for this choice is obtained by comparing several measured statistics of u/y with the corresponding numerical data.     

Electrical charging of bodies as a consequence of charged-particle extraction by a hydrodynamic flow

We investigate the problem of electrical charging of bodies as a result of charged-particle extraction by a hydrodynamic flow. The analysis is performed in view of the application to the problem of motion electrification of aircraft caused by a stream of charged particles into the surrounding space. We formulate the appropriate system of nonstationary electrohydrodynamic equations. It is shown that in many applications the charging of electrically insulated bodies consists of two successive intermediate processes. The first process is the formation of charge Q on the body in time T₁ The second process consists of a change of the body potential (with a constant charge Q) as a consequence of the stream of charged particles into the outside space noted above. At the end of the second process (with duration T₂) the body potential is at . We also investigate the problem of charging a spherical source of neutral and charged particles. Using the analytical solution we find the quantities Q and and the characteristic times T₁ and T₂. It is shown that the time T₂ can exceed T₁ by several orders of magnitude. We formulate the problems of nonstationary electric fields during the extraction of several types of particles.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 94–103, September–October, 1977.     

The dynamic and steady shear properties of synovial fluid and of the components making up synovial fluid

Steady-shear and dynamic properties of a pooled sample of cattle synovial fluid have been measured using techniques developed for low viscosity fluids. The rheological properties of synovial fluid were found to exhibit typical viscoelastic behaviour and can be described by the Carreau type A rheological model. Typical model parameters for the fluid are given; these may be useful for the analysis of the complex flow problems of joint lubrication.The two major constituents, hyaluronic acid and proteins, have been successfully separated from the pooled sample of synovial fluid. The rheological properties of the hyaluronic acid and the recombined hyaluronic acid-protein solutions of both equal and half the concentration of the constituents found in the original synovial fluid have been measured. These properties, when compared to those of the original synovial fluid, show an undeniable contribution of proteins to the flow behaviour of synovial fluid in joints. The effect of protein was found to be more prominent in hyaluronic acid of half the normal concentration found in synovial fluid, thus providing a possible explanation for the differences in flow behaviour observed between synovial fluid from certain diseased joints compared to normal joint fluid.Nomenclature A Ratio of angular amplitude of torsion head to oscillation input signal - G Storage modulus - G Loss modulus - I Moment of inertia of upper platen — torsion head assembly - K Restoring constant of torsion bar - N ₁ First normal-stress difference - R Platen radius - S ⁽ⁱ⁾ Geometric factor in the dynamic property analysis - t ₁ Characteristic time parameter of the Carreau model - X, Y Carreau model parameters - Z () Reimann Zeta function of - Carreau model parameter - Shear rate - Apparent steady-shear viscosity - ^* Complex dynamic viscosity - Dynamic viscosity - Imaginary part of the complex dynamic viscosity - ₀ Zero-shear viscosity - ₀ Cone angle - Carreau model characteristic time - Density of fluid - Shear stress - Phase difference between torsion head and oscillation input signals - ₀ Zero-shear rate first normal-stress coefficient - Oscillatory frequency     

Supersonic nonequilibrium flow past segmental bodies of a mixture simulating the atmosphere of venus

Calculations of the flow of the mixture 0.94 CO₂+0.05 N₂+0.01 Ar past the forward portion of segmentai bodies are presented. The temperature, pressure, and concentration distributions are given as a function of the pressure ahead of the shock wave and the body velocity. Analysis of the concentration distribution makes it possible to formulate a simplified model for the chemical reaction kinetics in the shock layer that reflects the primary flow characteristics. The density distributions are used to verify the validity of the binary similarity law throughout the shock layer region calculated.The flow of a CO₂+N₂+Ar gas mixture of varying composition past a spherical nose was examined in [1]. The basic flow properties in the shock layer were studied, particularly flow dependence on the free-stream CO₂ and N₂ concentration.New revised data on the properties of the Venusian atmosphere have appeared in the literature [2, 3] One is the dominant CO₂ concentration. This finding permits more rigorous formulation of the problem of blunt body motion in the Venus atmosphere, and attention can be concentrated on revising the CO₂ thermodynamic and kinetic properties that must be used in the calculation.The problem of supersonic nonequilibrium flow past a blunt body is solved within the framework of the problem formulation of [4].Notation V body velocity - shock wave standoff - universal gas constant - ratio of frozen specific heats - hRt/m enthalpy per unit mass undisturbed stream P pressure - density - T temperature - m molecular weight - c_p specific heat at constant pressure - (X) concentration of component X (number of particles in unit mass) - R body radius of curvature at the stagnation point - _j rate of j-th chemical reaction shock layer P V ² pressure - density - TT temperature - mm molecular weight Translated from Izv. AN SSSR. Mekhanika Zhidkosti i Gaza, Vol. 5, No. 2, pp. 67–72, March–April, 1970.The author thanks V. P. Stulov for guidance in this study.     

Evaluation of the dynamic-mechanical properties of solids from a cooperative model for stress relaxation

For many solid materials the stress relaxation process obeys the universal relationF = – (d/d lnt)_max = (0.1 ± 0.01) ( ₀ — _i ), regardless of the structure of the material. Here denotes the stress,t the time, ₀ the initial stress of the experiment and _i the internal stress. A cooperative model accounting for the similarity in relaxation behaviour between different materials was developed earlier. Since this model has a spectral character, the concepts of linear viscoelasticity are used here to evaluate the corresponding prediction of the dynamic mechanical properties, i.e. the frequency dependence of the storageE () and lossE () moduli. Useful numerical approximations ofE () andE () are also evaluated. It is noted that the universal relation in stress relaxation had a counterpart in the frequency dependence ofE (). The theoretical prediction of the loss factor for high-density polyethylene is compared with experimental results. The agreement is good.     

Laminar natural convection over a slender vertical frustum of a cone

The problem of laminar, natural convection flow over a slender frustum of a cone is treated in this paper. The governing differential equations are solved by a combination of quasi-linearization and finite-difference methods. Numerical solutions are obtained for Pr=0.7 and for a range of values of the transverse curvature parameter. It is shown that the effect of transverse curvature is of great significance in such flows.

---

Laminare natürliche Konvektion an einem dünnen, senkrechten Kegelstumpf

Zusammenfassung In diesem Bericht ist das Problem der laminaren natürlichen Konvektionsströmung an einem dünnen Kegelstumpf behandelt. Die maßgebliche Differentialgleichung ist durch eine Verbindung von Quasilinearisation und Differenzenverfahren gelöst. Eine numerische Lösung für Pr=0.7 wird für verschiedene Werte eines Krümmungsparameters angegeben. Es ist gezeigt, daß in solchen Strömungen dieser Krümmungsparameter eine große Bedeutung besitzt.

---

Nomenclature f dependent variable, defined in Eq. (7) - g dependent variable, defined in Eq. (7) - g_e gravitational acceleration - h heat transfer coefficient, or -grid - k heat conductivity, or -grid - L characteristic length - Nu Nusselt number - Pr Prandtl number - r radial distance from the axis of the cone - R transverse curvature effect ratio, defined in Eq. (23) - Re Reynold number - T temperature - u, v velocity components in the x- and y-directions, respectively - x, y rectangular coordinates Greek letters dimensionless temperature, definedinEq. (4) - bulk modulus - cone angle - dynamic viscosity - stream function - , independent variable, defined in (7) - transverse curvature parameter     

Effect of Dynamic Prehistory on Aerodynamics of a Laminar Separated Flow in a Channel Behind a Rectangular Backward‐Facing Step

The effect of dynamic prehistory of the flow and the channelexpansion ratio on aerodynamics of a steady separated laminar flow behind a rectangular backwardfacing step located in a planeparallel channel is numerically studied. It is shown that the boundary layer upstream of the flow separation exerts a strong effect on flow characteristics behind the step. A decrease in the boundarylayer thickness in the cross section of the step leads to a decrease in the separationregion length, and an increase in the channelexpansion ratio with a fixed initial boundarylayer thickness and Reynolds number leads to an increase in the separationregion length.     

New concepts in relative permeabilities at high capillary numbers for surfactant flooding

Flooding oil reservoirs with surfactant solutions can increase the amount of oil that can be recovered. Macroscopic modelling of the process requires relative permeabilities to be functions of saturation and capillary number. With only limited experimental data, relative permeabilities have usually been assumed to be linear functions of saturation at high capillary numbers. The experimental data is reviewed, some of which suggest that this assumption is not necessarily correct. The basis for the assumption is therefore reviewed and it is concluded that the linear model corresponds to microscopically segregated flow in the porous medium. Based on new but equally plausible complementary assumptions about the flow pattern, a mixed flow model is derived. These models are then shown to be limiting cases of a droplet model which represents the mixing scale within the porous medium and gives a physical basis for interpolating between the models. The models are based on physical concepts of flow in a porous medium and so the approach described here represents a significant improvement in the understanding of high capillary number flow. This is shown by the fact that fewer parameters are needed to describe experimental data.Notation A total cross-sectional area assigned to capillary bundle - A ⁽ⁱ⁾ physical cross-sectional area of tube i - c ⁽ⁱ⁾ ordered configurational label for droplets in tube i - c configuration label for tube i (order not considered) - D defined by Equation (26) - E(...) expectation value with respect to the trinomial distribution - S _r ⁽⁾ fractional flow of phase - k absolute permeability - k _r relative permeability of phase - k _r ⁰ endpoint relative permeability of phase - L capillary tube length in bundle model - m ⁽ⁱ⁾ number of droplets of phase a occupying tube i - n exponent for phase a in Equation (2) - N number of droplets in bundle model - N _c capillary number - p pressure - p(c') probability of configuration c - Q ⁽ⁱ⁾ total volume flow rate in tube i - S saturation of phase - S flowing saturation of phase - S _r residual saturation of phase - S _r ⁽⁾ saturations when fractional flow of phase is 1 in the case of varying residual saturations for three-phase flow ( ) - t _c residence time for droplet configuration c - v ⁽ⁱ⁾ total fluid velocity in bundle tube i - , phase label - p pressure differential across capillary bundle - ⁽ⁱ⁾ tube conductivity defined by Equation (7) - viscosity of phase - interfacial tension - gradient operator - ... average over tube droplet configurations     

Effect of Streamwise Streaky Structures on Turbulization of a Circular Jet

Experimental investigations of the influence of streamwise streaky structures on turbulization of a circular laminar jet are described. The qualitative characteristics of jet evolution are studied by smoke visualization of the flow pattern in the jet and by filming the transverse and longitudinal sections of the jet illuminated by the laser sheet with image stroboscopy. It is shown that the streaky structures can be generated directly at the nozzle exit, and their interaction with the Kelvin–Helmholtz ring vortices leads to emergence of azimuthal beams ( structures) by a mechanism similar to threedimensional distortion of the twodimensional Tollmien–Schlichting wave at the nonlinear stage of the classical transition in nearwall flows. The effect of the jetexhaustion velocity and acoustic action on jet turbulization is considered.     

Finite difference analysis of plane Poiseuille and Couette flow developments

Summary The problem of flow development from an initially flat velocity profile in the plane Poiseuille and Couette flow geometry is investigated for a viscous fluid. The basic governing momentum and continuity equations are expressed in finite difference form and solved numerically on a high speed digital computer for a mesh network superimposed on the flow field. Results are obtained for the variations of velocity, pressure and resistance coefficient throughout the development region. A characteristic development length is defined and evaluated for both types of flow.Nomenclature h width of channel - L ratio of development length to channel width - p fluid pressure - p ₀ pressure at channel mouth - P dimensionless pressure, p/ ² - P ₀ dimensionless pressure at channel mouth - P pressure defect, P ₀–P - (P)₀ pressure defect neglecting inertia - Re Reynolds number, uh/ - u fluid velocity in x-direction - mean u velocity across channel - u ₀ wall velocity - U dimensionles u velocity u/ - U _c dimensionless centreline velocity - U ₀ dimensionless wall velocity - v fluid velocity in y-direction - V dimensionless v velocity, hv/ - x coordinate along channel - X dimensionless x-coordinate, x/h ² - y coordinate across channel - Y dimensionless y-coordinate, y/h - resistance coefficient, - ₀ resistance coefficient neglecting inertia - fluid density - fluid viscosity