Prearation of Highly Ordered Mesoporous Silica Materials and Application as Enzeme Supports

An enzyme, horseradish peroxidase (HRP), was adsorbed in the manner of single immersion method on the silica mesoporous materials, FSM-16, MCM-41 and SBA-15 with various pore diameters from 27 to 92 and their enzymatic activity in an organic solvent and the thermal stability were studied. FSM-16 and MCM-41 showed larger amount of adsorption of HRP than SBA-15 or silica gel,when the pore sizes were larger than the spherical molecular diameter of HRP (ca 64×37). The increased enzyme adsorption capacity may be due to the surface characteristics of FSM-16 and MCM-41, which would be consistent with the observed larger adsorption capacity of cationic pigment compared with anionic pigment for these materials. The immobilized HRP on FSM-16 and MCM-41 with pore diameter above 50 showed the highest enzymatic activity in an organic toluene and thermal stability in aqueous solution at the temperature of 70℃. The immobilized enzymes on the other mesoporous materials including large or small pore sized FSM-16 showed lower enzymatic activity in an organic solvent and the thermal stability. Both surface character and size matching between pore sizes and the molecular diameters of HRP were important in achieving high enzymatic activity in organic solvent and high thermal stability.     

Adsorption properties of gases on mesoporous chromium silicate

The properties of nitrogen, carbon dioxide, and nitrogen dioxide adsorption onto mesoporous chromium silicates were studied by measurements of both the adsorption isotherms and the IR spectra. The pore sizes of two types of chromium silicates, Cr-FSM-16 (Si/Cr=170 (Cr-FSM-16 [170]) and 390 (Cr-FSM-16 [390])), which contain different amount of Cr, were 2.75 nm. BET surface areas of Cr-FSM-16 were 590 m2/g and they were smaller than that onto FSM-16. The initial heat of adsorption of nitrogen onto Cr-FSM-16 was higher than that onto FSM-16. But the initial heat of adsorption of carbon dioxide onto Cr-FSM-16 was smaller than that onto FSM-16. These results indicated that Cr in Cr-FSM-16 decreased adsorption interaction with carbon dioxide. When nitrogen dioxide was adsorbed on FSM-16 and Cr-FSM-16 at 303 K under no light, an absorption band of nitrogen monoxide adsorbed was measured by IR spectroscopy. This decomposition of nitrogen dioxide by FSM-16 and Cr-FSM-16 was caused by SiOH and Cr, respectively.     

胆酸和L-苯丙氨酸的固相包合作用

研究了胆酸(CA)和L-苯丙氨酸(PAA)以固相熔融法形成的固相包埋配位. 通过粉末X射线衍射图、红外光谱、粉末荧光光谱及差热分析方法, 测定了固相包埋形成的CA-PAA配合物. 同时, 用溶剂共沉淀法和机械研磨法对比了CA-PAA包埋物的形成. 结果表明, 封管固相熔融时PPA以客体形式被包合进主体CA形成的通道; 研磨法中CA部分包埋PPA; 溶剂共沉淀方法中, PPA不被主体CA包埋, 而使用的相应溶剂被CA包埋.     

Specific inclusion mode of guest compounds in the amylose complex analyzed by solid state NMR spectroscopy

The inclusion compound formation between linear amylose of molecular weight 102500 (AS100) and p-aminobenzoic acid (PA) during the sealed-heating process was investigated by powder X-ray diffractometry, infrared spectroscopy and solid state NMR spectroscopy. Sealed-heating of AS100 and PA at 100 degrees C for 6 h provided an inclusion compound with 6(1)-helix structure, while a 7(1)-helix structure was found when sealed-heating was carried out at 150 degrees C for 1 h. The formation of an inclusion compound was not observed when sealed-heating was performed at 50 degrees C for 6 h. The 7(1)-helix inclusion compound maintained its structure even during storage at high temperature while the 6(1)-helix inclusion compound decomposed and returned to the original V(a)-amylose upon heating to 180 degrees C. Quantitative determination revealed that one PA molecule could be included per one helical turn of AS100 for both 6(1)-helix and 7(1)-helix inclusion compounds. Solid state NMR spectroscopy suggested that PA molecules were included in the amylose helix core in the 7(1)-helix inclusion compound, while in the case of 6(1)-helix inclusion compound, PA molecules were accommodated in the interstices between amylose helices. Moreover, the inclusion compound formation by sealed-heating of AS100 was also observed when using PA analogues as guest compounds. The binding ratio of AS100 and PA analogues varied depending on the size of guest molecules.     

Synthesis of mesoporous zeolite a by resorcinol-formaldehyde aerogel templating

Mesoporous zeolite A has been synthesized by using a template method with resorcinol-formaldehyde aerogels having three-dimensional mesopores. It was characterized with X-ray powder diffraction, Fourier transform infrared spectroscopy, Raman spectroscopy, field emission scanning electron microscopy, thermogravimetric analysis, and nitrogen adsorption/desorption. The pore size distribution calculated from the nitrogen adsorption isotherm is a bimodal distribution with micropores and mesopores. Field emission scanning electron micrograph observations confirm the presence of mesopores.     

Developments and structures of mesopores in alkaline-treated ZSM-5 zeolites

ZSM-5 zeolites with SiO₂/Al₂O₃ molar ratio of 24 were treated in 0.05 M aqueous sodium hydroxide solution at 325 K in different periods. The samples were characterized by means of nitrogen adsorption at 77 K, field emission scanning electron microscopy, X-ray diffractometry, and Fourier transform infrared spectroscopy. Analysis of the experimental results showed that the alkaline treatment periods have influence on the developments and structures of mesopores in the alkaline-treated ZSM-5 zeolites. Alkaline treatment initially develops mesopores mainly from the boundary portion of MFI zeolites to the bulk, while prolonged treatment destroys the mesopores, and an optimum mesoporosity is obtained by the treatment for 1.5 h. On the other hand, crystallinities and short-range order in alkaline treated zeolites have remained virtually unchanged according to the examination from X-ray diffractometry and Fourier transform infrared spectroscopy.     

Rapid adsorption and entrapment of benzoic acid molecules onto mesoporous silica (FSM-16)

Changes in the molecular state of benzoic acid (BA) in the presence of folded sheet mesoporous material (FSM-16), which has uniformly sized cylindrical mesopores and a large surface area, were assessed with several analyses. When BA was blended with FSM-16 for 5 min (BA content=30%), the X-ray diffraction peaks of BA crystals disappeared, suggesting an amorphous state. Fluorescence analysis of the mixture showed a new fluorescence emission peak for BA at 386 nm after mixing with FSM-16. Fluorescence lifetime analysis of the BA component in the mixture at 386 nm showed a longer lifetime in comparison with that of BA crystals. The solid-state (13)C CP/MAS and PST/MAS NMR spectra of the mixture with FSM-16 showed a significantly different spectral pattern from the mixture with nonporous glass, whose NMR spectra were identical to those of BA crystals. These results indicate that BA molecules disperse quickly into the hexagonal channels of FSM-16 by a simple blending procedure and adsorbed BA molecules had clearly different physicochemical properties to BA crystals.     

Adsorption hysteresis of nitrogen and argon in pore networks and characterization of novel micro- and mesoporous silicas

We report results of nitrogen and argon adsorption experiments performed at 77.4 and 87.3 K on novel micro/mesoporous silica materials with morphologically different networks of mesopores embedded into microporous matrixes: SE3030 silica with worm-like cylindrical channels of mode diameter of approximately 95 angstroms, KLE silica with cage-like spheroidal pores of ca. 140 angstroms, KLE/IL silica with spheroidal pores of approximately 140 angstroms connected by cylindrical channels of approximately 26 angstroms, and, also for a comparison, on Vycor glass with a disordered network of pores of mode diameter of approximately 70 angstroms. We show that the type of hysteresis loop formed by adsorption/desorption isotherms is determined by different mechanisms of condensation and evaporation and depends upon the shape and size of pores. We demonstrate that adsorption experiments performed with different adsorptives allow for detecting and separating the effects of pore blocking/percolation and cavitation in the course of evaporation. The results confirm that cavitation-controlled evaporation occurs in ink-bottle pores with the neck size smaller than a certain critical value. In this case, the pressure of evaporation does not depend upon the neck size. In pores with larger necks, percolation-controlled evaporation occurs, as observed for nitrogen (at 77.4 K) and argon (at 87.3 K) on porous Vycor glass. We elaborate a novel hybrid nonlocal density functional theory (NLDFT) method for calculations of pore size distributions from adsorption isotherms in the entire range of micro- and mesopores. The NLDFT method, applied to the adsorption branch of the isotherm, takes into account the effect of delayed capillary condensation in pores of different geometries. The pore size data obtained by the NLDFT method for SE3030, KLE, and KLE/IL silicas agree with the data of SANS/SAXS techniques.     

Fabrication and characterization of bimetallic Pt-Au nanowires supported on FSM-16 and their catalytic activities toward water-gas shift reaction

A facile, previously unexplored, method to synthesize bimetallic Pt-Au nanowires (20nm diameter×120-170nm long) on mesoporous FSM-16 (2.7nm) was fabricated by co-impregnation of H(2)PtCl(6) with HAuCl(4) followed by evacuation at 300K and finally exposure to the CO/H(2)O gas mixture (60:5Torr) at 323K for 1.0h. On the other hand, spherical monometallic nanoparticles of pure Pt (7.0nm diameter) and Au (7-26nm diameter) were synthesized as well, by impregnation, at the same reaction conditions. The catalysts were characterized by in situ FTIR spectroscopy, UV-vis absorption spectroscopy, TEM, TPR and TPCOR. The catalytic activities toward the water-gas shift reaction (WGSR) were also examined under atmospheric pressure and at the margin of 323-373K. The optical absorption spectra showed a remarkable shift and broadening of Pt-Au surface Plasmon resonance band at 515nm apart from those of individual analogue emphasizing bimetallic formation. Results from in situ FTIR spectroscopy indicated that incorporation of Au assisted and stabilized the formation of carbonyl clusters of Pt-Au-CO (2084cm(-1)) and Pt-CO (1888cm(-1)) inside the host FSM-16. The Pt-Au carbonyl clusters built up at the moment of vanishing the linear carbonyl band of the charged Au (Au(+)-CO, 2186cm(-1)) along with a concomitant increase in the reduced gold (Au(0)-CO, 2124cm(-1)) species. TPR profiles showed that the H(2) consumed was higher for Pt/FSM-16 than for Pt-Au/FSM-16 verifying the facile reduction of Pt moieties after addition of Au. The CO adsorption peak maximum, in TPCOR, for Pt/FSM-16 occurred at higher temperature than that of Pt-Au/FSM-16, which exhibited higher amounts of CO(2) produced. The relative decrease in CO bindings on bimetallic surface was responsible for increasing the CO oxidation activity mainly through an association mechanism. Accordingly, the activity of Pt-Au/FSM-16 towards WGS showed a marked increase (8-23 times) compared with those of monometallics emphasizing the dependence of this reaction on the electronic defects of the nanowires. A straightforward reduction mechanism was deduced for Pt-Au alloy formation in view of the results obtained.     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6, 同时通过改变水热温度制备了不同孔径大小的SBA-15, 并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段, 对其介孔结构进行了表征. 以正丁醛为探针分子, 考察了其对有机醛的吸附, 并与Y-沸石的吸附性能做了对比. 结果表明, 材料的介孔比表面积与其对正丁醛的吸附量成正比, 吸附等温线符合Langmuir 模型, 属于单层吸附, 具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g^-1). 最后将SBA-15添加到卷烟滤嘴中, 实验结果表明, SBA-15能显著降低卷烟烟气中巴豆醛的释放量.     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6,同时通过改变水热温度制备了不同孔径大小的SBA-15,并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段,对其介孔结构进行了表征.以正丁醛为探针分子,考察了其对有机醛的吸附,并与Y-沸石的吸附性能做了对比.结果表明,材料的介孔比表面积与其对正丁醛的吸附量成正比,吸附等温线符合Langmuir模型,属于单层吸附,具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g-1).最后将SBA-15添加到卷烟滤嘴中,实验结果表明,SBA-15能显著降低卷烟烟气中巴豆醛的释放量.     

NMR Study of Pore Surface and Size in a Mesoporous Material FSM-16

Surface structure, pore size distribution and pore wall thickness of a mesoporous material FSM-16 have been studied by X-ray powder diffraction (XRD), ^lH and ²⁹Si MAS NMR and ¹H liquid-state NMR, and by applying surface silylation as a probe. Concentrations of surface hydroxyl groups for FSM-16 are estimated from ²⁹Si and ¹H MAS NMR, which are about 3×l0²¹ g^-1, corresponding to approximately 3 nm^-2. O₂ molecules contribute to ²⁹Si spin-lattice relaxation of Q² and Q³ as well as Q⁴, suggesting thin wall thickness. ¹H MAS NMR spectra indicate the presence of isolated and hydrogen-bonded hydroxyl groups. Both hydroxyl groups are silylated, where the silylated fraction is about 50%. The spatial distribution of surface hydroxyl groups is estimated from the line width in ¹H static spectra. A rather homogeneous distribution is demonstrated in one of the samples. The sample with less homogeneous distribution has a larger affinity for moisture. Pore size and pore wall thickness were determined by ¹H NMR measurements on water saturated FSM-16 samples, which are in good agreement with literature values obtained by N₂ adsorption isotherms and transmission electron micrographs on a similar sample. In benzene saturated samples, a non-freezing surface layer of benzene is much thicker than that of water, which indicates a stronger interaction between benzene and the FSM-16 surface.     

联合载体用于改善白藜芦醇固体分散体性能

通过载体聚乙烯吡咯烷酮(PVPk29/32)和羟丙基甲基纤维素(HPMC),采用溶剂法制备白藜芦醇(Res)二元及三元固体分散体。 用傅里叶变换红外光谱(FTIR)、调制式差示扫描量热(MDSC)和X射线粉末衍射(XRD)等技术手段来表征Res二元和三元固体分散体并考察其溶出度。 FTIR结果显示,Res与PVPk29/32及HPMC均存在氢键相互作用;溶出结果表明,二元和三元固体分散体均能提高药物的溶出度。 而XRD和MDSC结果表明,三元固体分散体的相容性优于二元固体分散体;3个月的加速实验(40 ℃,75%RH(relative humidity))中,XRD、MDSC及体外溶出结果表明,Res三元固体分散体的稳定性优于Res二元固体分散体。 HPMC的加入可以改善Res三元固体分散体的溶出及稳定性。     

Estimation of physical stability of amorphous solid dispersion using differential scanning calorimetry

The physical stability of amorphous drug in solid dispersion was estimated using differential scanning calorimetry (DSC). Tolbutamide (TB) and flurbiprofen (FBP) were selected as insoluble drugs in water. Polyvinylpyrrolidone (PVP) was selected as a polymer for solid dispersion. Solid dispersions of various ratios of TB or FBP and PVP-K25 were prepared by solvent evaporation method and the induction period of crystallization from amorphous drug in solid dispersion was measured by DSC. Compared with FBP, the induction period of crystallization from TB was delayed by an addition of PVP. The improvement of the physical stability by the addition of PVP-K25 was estimated from the activation energy of diffusion of drug molecules and the interfacial free energy between drug crystal and supercooled liquid of drug in solid dispersion. From thses results, the hindrance of the diffusivity of the drug molecule might be mainly affected the delay of the induction period of crystallization of TB and FBP.     

Quantification of nanoparticles in aqueous food matrices using Particle-Induced X-ray Emission

Nanoparticles (NPs) of SiO(2) (15 nm) or Ag (20 - 40 nm) were dispersed in water, coffee and milk at several aqueous dilutions. The NPs dispersions concentrations were quantified with an ion beam technique: Particle-Induced X-ray Emission. Additional measurements in relation to the state of the NPs dispersions were done: particle size distribution by centrifuge liquid sedimentation and the extreme surface composition by X-ray photoelectron spectroscopy. The particle size distribution of SiO(2) and Ag NPs dispersions in water and Ag NPs in coffee remained mostly as primary particles with hydrodynamic diameters close to the reported pristine NPs diameter. SiO(2) NPs agglomerated in coffee. In milk, both NPs presented an adsorption with milk lipids. Extreme surface composition corroborated adsorption in milk and showed that SiO(2) agglomerates adsorb some coffee components. A linear tendency in the measurement of the concentration dilutions of all dispersions was measured, and a lack of media influence in the slope of each curve was found. Limits of detection with the current setup were estimated at 0.5 and 0.3 mg/ml for SiO(2) and Ag NPs, respectively.     

Biomaterial immobilization in nanoporous carbon molecular sieves: influence of solution pH, pore volume, and pore diameter

The adsorption of lysozyme (Lz) onto nanoporous carbon molecular sieves with various pore diameters has been studied at different solution pH values. All the adsorption isotherms have successfully been correlated by the Langmuir equation. The amount of adsorbed Lz depends on the solution pH as well as on the specific pore volume and pore diameter of the adsorbents. The maximum adsorption was observed near the isoelectric point of the Lz (pI approximately 11), suggesting that suppression of electric repulsion between the enzymes plays an important role in the adsorption process. Moreover, the amount adsorbed depends on the pore size and pore volume of the nanoporous carbon adsorbents, indicating that the Lz molecules are adsorbed inside the mesopores. CMK-3-150 shows a larger amount of Lz adsorption as compared to CMK-3. The increased Lz adsorption capacity of CMK-3-150 may be due to the larger pore volume and pore diameter as compared to that of CMK-3. The unaltered structural order of the nanoporous adsorbents after the adsorption has been confirmed by the physicochemical characterization techniques such as XRD and N(2) adsorption. In addition, FT-IR spectroscopic studies confirm that the Lz used in this study is stable even after the adsorption on the nanoporous carbon. These results indicate that nanoporous carbon has superior water stability and thus is a more appropriate adsorbent for biomaterials than nanoporous silica.     

ZSM-5 monolith of uniform mesoporous channels

A ZSM-5 monolith of uniform mesopores(meso-ZSM-5) was synthesized with the template method using carbon aerogel of uniform mesopores of great pore volume. The pore size distribution determined by N2 adsorption showed the presence of mesopores with an average pore width of 11 nm and micropores with an average pore width of 0.51 nm. Field emission scanning electron micrograph observation revealed the presence of uniform mesopores. X-ray diffraction and FT-IR provided evidence that the synthesized meso-ZSM-5 monolith has a highly crystalline ZSM-5 structure.     

Studies on mesoporous niobosilicates synthesized using F127 triblock copolymer

A detailed characterization of cage-like mesoporous SBA-16 niobosilicate with tailored features of the structure is reported. The materials were synthesized in a EO₁₀₆PO₇₀EO₁₀₆(F127)-water system under acidic conditions and the pore diameters were tuned by varying the hydrothermal treatment temperature and time. The effects of the synthesis parameters on the structural/textural properties of the cubic Im3m niobosilicates have been investigated systematically. We show that the total pore volume, pore diameter, and micro-/mesopores ratio can be controlled very efficiently by changing the synthesis parameters.     

利用X射线小角度散射法研究大孔吸附树脂的孔结构——平均孔径的测定

利用小角X射线散射技术研究了吸附剂的孔结构。选择含6％二乙烯基苯和100％汽油作致孔剂制备的干燥及水和甲苯溶胀的聚合物小球为样品,测定了干态及溶胀态样品的平均孔径及孔径分布。得到了随溶剂吸附量增加平均孔径变化的关系。对吸附和溶胀机理作了初步探讨。     

Low-temperature CO oxidation over CuO-CeO_2/SiO_2 catalysts:Effect of CeO_2 content and carrier porosity

The effects of CeO2 contents and silica carrier porosity with their pore diameters ranging from 5.2 nm to 12.5 nm of CuO-CeO2/SiO2 cata-lysts in CO oxidation were investigated.The catalysts were characterized by N2 adsorption/desorption at low temperature,X-ray diffraction (XRD),temperature-programmed reduction by H2 (H2-TPR),oxygen temperature programmed desorption (O2-TPD) and X-ray photoelectron spectroscopy (XPS).The results suggested that,the ceria content and the porosity of SiO2 carrier possessed great impacts on the structures and catalytic performances of CuO-CeO2/SiO2 catalysts.When appropriate content of CeO2 (Ce content 8 wt%) was added,the catalytic activity was greatly enhanced.In the catalyst supported on silica carrier with larger pore diameter,higher dispersion of CuO was observed,better agglomeration-resistant capacity was displayed and more lattice oxygen could be found,thus the CuO-CeO2 supported on Si-1 showed higher catalytic activity for low-temperature CO oxidation.