Phase formation in the BaCO<Subscript>3</Subscript>–PbO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> system

Features of the formation of lead-ferroniobate compounds in the xBaCO₃–(1 – x)PbO–Fe₂O₃–Nb₂O₅ system by solid-phase synthesis are investigated. For perovskite-type lead-ferroniobate solid solution, a single-phase concentration region is revealed at 1233 K. The crystalline structures of the synthesized compounds are refined using Rietveld analysis and the Pm3?m and R3m space groups. Ceramic samples of lead ferroniobate are studied by scanning electron microscopy.     

Elastic properties of TeO<Subscript>2</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Ag<Subscript>2</Subscript>O glasses

A series of glasses [(TeO₂) _x (B₂O₃)_1−x ]_1−y [Ag₂O] _y with x = 70 and y = 10, 15, 20, 25 and 30 mol% were synthesised by rapid quenching. Longitudinal and shear ultrasonic velocity were measured at room temperature and at 5 MHz frequency. Elastic properties, Poisson's ratio, microhardness, softening temperature and Debye temperature have been calculated from the measured density and ultrasonic velocity at room temperature. The experimental results indicate that the elastic constants depend upon the composition of the glasses and the role of the Ag₂O inside the glass network is discussed. Estimated parameters based on Makishima–Mackenzie theory and bond compression model were calculated in order to analyse the experimental elastic moduli. Comparison between the experimental elastic moduli data obtained in the study and the calculated theoretically by the mentioned above models has been discussed.     

Effect of mixed glass formers on the crystallization kinetics in AgI–Ag<Subscript>2</Subscript>O–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–MoO<Subscript>3</Subscript> glassy superionic system

The crystallization and glass transition kinetics using differential scanning calorimetry (DSC) in 50AgI–33.33Ag₂O–16.67[(V₂O₅)_1−x –(MoO₃) _x ] superionic glassy system is discussed. Thermal stability of glass, studied using various criteria, does not vary significantly with glass former variation. However, the activation energies for structural relaxation (E _s) at glass transition temperature and crystallization (E _c) obtained using Moynihan and Kissinger, Matusita-Sakka formulations found to exhibit interesting trends with MoO₃ substitution in the glass matrix. It is noticed that the electrical conductivity (σ)–temperature (T) cycles obtained at a typical heating rate of 1 °C/min do exhibit significant thermal events. The conductivity after first heating cycle at room temperature is found to be increasing with MoO₃ content and maximum for x = 0.3 (~10⁻³ Ω⁻¹ cm⁻¹ at 30 °C) which is comparable to that of the host 50AgI–33.33Ag₂O–16.67V₂O₅ glassy system. The parameters obtained from σ–T plots and DSC scans do complement each other in a particular range of composition.     

Electrical conductivity and dielectric relaxation studies on microwave synthesized Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>·NaPO<Subscript>3</Subscript>·MoO<Subscript>3</Subscript> glasses

Electrical conductivity and dielectric relaxation studies on SO₄ ^2? doped modified molybdo-phosphate glasses have been carried out over a wide range of composition, temperature and frequency. The d.c. conductivities which have been measured by both digital electrometer (four-probe method) and impedance analyser are comparable. The relaxation phenomenon has been rationalized using electrical modulus formalism. The use of modulus representation in dielectric relaxation studies has inherent advantages viz., experimental errors arising from the contributions of electrode-electrolyte interface capacitances are minimized. The relaxation observed in the present study is non-Debye type. The activation energies for relaxation were determined using imaginary parts of electrical modulus peaks which were close to those of the d.c. conductivity implying the involvement of similar energy barriers in both the processes. The enhanced conductivity in these glasses can be attributed to the migration of Na⁺, in expanded structures due to the introduction of SO₄ ^2? ions.     

Magnetic and magnetoresistive properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sr<Subscript>2</Subscript>FeMoO<Subscript>6–δ</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoheterostructures

A method has been developed for fabricating nanoporous matrices based on anodic aluminum oxide for the deposition of ferromagnetic nanoparticles in them. The modes of deposition of strontium ferromolybdate thin films prepared by the ion-plasma method have been worked out, and the magnetic and magnetoresistive properties, structure, and composition of the films have been investigated. It has been revealed that the microstructure and properties of the strontium ferromolybdate films deposited by ionplasma sputtering depend on the deposition rate and the temperature of the substrate. Based on the measurement of the electrical resistivity of nanoheterostructures in a magnetic field, it has been found that the magnetoresistance reaches 14% at T = 15 K and B = 8 T, which is due to the manifestation of tunneling magnetoresistance.     

On the Coexistence of Chemically Similar Stable and Metastable Phases in the BeO–MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> System

The joint crystallization of the stable phase (a number of solid solutions of chromium-containing beryllian indialite) and metastable phases (crystalline modifications) of the compound with β-quartz structure (Si_0.64Al_0.28Mg_0.21Be_0.09)^IVO₂ ~ Mg_1.89Be_0.81Al_2.52Si_5.76O₁₈ admixed with Cr₂O₃ phases of khmaralite Mg_1.21Cr_0.01Be_0.46Al_1.78Si_3.38O₂₀ and spinel {(Mg_0.95Be_0.045Si_0.005)^IV(Al_1.31Cr_0.67Mg_0.02)^VI}O₄ is performed using melted chromium–beryllian indialite preliminarily obtained by solid-phase synthesis as a precursor. Simultaneously, the residual X-ray amorphous melt of composition Mg_1.83Cr_0.01Be_1.04Al_2.64Si_5.57O₁₈ is hardened. Thus, a reconstructive transition from the beryllian indialite melt to a phase with the β-quartz structure is implemented, and the chemical similarity of these compounds is demonstrated. The rate of change in the crystallization isotherm of 2°С/h and increased heat outflow through the highly heat-conducting walls of the Pt–Rh crucible (taper) contribute to this process.     

Deep metastable eutectic nanometer-scale particles in the MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> system

Laboratory vapor phase condensation experiments systematically yield amorphous, homogeneous, nanoparticles with unique deep metastable eutectic compositions. They formed during the nucleation stage in rapidly cooling vapor systems. These nanoparticles evidence the complexity of the nucleation stage. Similar complex behavior may occur during the nucleation stage in quenched-melt laboratory experiments. Because of the bulk size of the quenched system many of such deep metastable eutectic nanodomains will anneal and adjust to local equilibrium but some will persist metastably depending on the time–temperature regime and melt/glass transformation.     

KF-doped BaTi<Subscript>2</Subscript>O<Subscript>5</Subscript> ferroelectric ceramics by solid-state reaction of KF and sol–gel-derived BaTi<Subscript>2</Subscript>O<Subscript>5</Subscript> powders

We report KF-doping work on the recently found ferroelectric material BaTi₂O₅. The ceramic samples, Ba_1-xK_xTi₂O_5-xF_x, were synthesized by solid-state reaction of mixed KF and sol–gel-derived BaTi₂O₅ powders at 1150 °C. An almost pure phase was obtained for nominal composition x≤0.097, while electron probe microanalysis indicated that the real incorporated K and F contents were less than half of the nominal values. It was observed that KF-doping is beneficial in enhancing the ceramic density to some extent, which is a key issue in sol–gel-derived BaTi₂O₅ ceramics, due to a possible liquid-phase sintering mechanism through the presence of melted KF at the sintering temperature. Scanning electron microscopy images showed that these porous ceramic samples are composed of sub-micron-sized powder aggregates which, with increasing KF-doping, undergo further agglomeration. Dielectric measurement from room temperature to ∼ 560 °C showed a broad ferroelectric phase transition, with T_C ∼ 430 °C for the undoped sample. As KF-doping increases, T_C decreases, and the magnitude of the dielectric constant maximum also displays a decreasing trend. The strongly reduced dielectric response can be partly understood by regarding the porous ceramic sample as a composite material composed of bulk BaTi₂O₅ and air, where the porosity has a significant influence on the effective dielectric constant. PACS 77.84.-s; 77.84.Dy; 81.20.Fw     

Sol–gel synthesis and characterization of Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite solid electrolytes

Composite solid electrolytes in the system (1???x)Li₂CO₃–xAl₂O₃, with x?=?0.0–0.5 (mole), were synthesized by a sol–gel method. The synthesis carried out at low temperature resulted in voluminous and fluffy products. The obtained materials were characterized by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy/energy-dispersive X-ray, Fourier transform infrared spectroscopy and AC impedance spectroscopy. Structural analysis of the samples showed an amorphous feature of Li₂CO₃ and traces of α-LiAlO₂, γ-LiAlO₂ and LiAl₅O₈. The prepared composite samples possess high ionic conductivities at 130–180 °C on account of the presence of lithium aluminates as well as the formation of a high concentration of an amorphous phase of Li₂CO₃ via this sol–gel preparative technique.     

Microwave dielectric properties of the 5.5Li<Subscript>2</Subscript>O–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>–7TiO<Subscript>2</Subscript> ceramics

A new Li₂O–Nb₂O₅–TiO₂ (LNT) ceramic with the Li₂O:Nb₂O₅:TiO₂ mole ratio of 5.5:1:7 was prepared by solid state reaction route. The phase and structure of the ceramic were characterized by X-ray diffraction and scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The microwave dielectric ceramic has low sintering temperature (∼1075°C) and good microwave dielectric properties of ε _r=42, Q×f=16900 GHz (5.75 GHz), and τ _f =63.7 ppm/°C. The addition of B₂O₃ can effectively lower the sintering temperature from 1075 to 875°C and does not induce degradation of the microwave dielectric properties. Obviously, the LNT ceramics can be applied to microwave low temperature-cofired ceramics (LTCC) devices.     

Influence of Matrix Nature on the Structural Characteristics of In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CeO<Subscript>2</Subscript> and SnO<Subscript>2</Subscript>–CeO<Subscript>2</Subscript> Composites Fabricated by the Impregnation Method

The structural characteristics, valence states, and distribution of cerium ions between the components in In₂O₃–CeO₂ and SnO₂–CeO₂ nanocomposites fabricated using the impregnation method were studied. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) were used to show that, during impregnation, cerium ions are not included into In₂O₃ crystals and are disposed only on their surface in the form of nano-sized crystallites or amorphous clusters. On the other side, under the contact of CeO₂ clusters with a surface of SnO₂ matrix crystals, cerium ions penetrate into the surface layer of these crystals. In contrast to an In₂O₃–CeO₂ system, where the addition of CeO₂ does not affect the conduction activation energy, where cerium oxide is added to SnO₂, the observed increase in the resistance of a SnO₂–CeO₂ composite is accompanied by a sufficient increase in activation energy. These data and the XPS spectra confirm the modification of the surface layers of conductive SnO₂ crystals as, a result of the penetration of cerium ions into these layers.     

Electrical conductivity and dielectric properties of β-BaB<Subscript>2</Subscript>O<Subscript>4</Subscript> crystal in the temperature range 90–300 K

The electrical conductivity σ and dielectric properties (?, tanδ) of β-BaB₂O₄ were studied in the temperature range 90–300 K. The quantities σ, ?, and tanδ were measured at frequencies of 0.1, 1, and 10 kHz and 1 MHz. The dielectric permittivity and electrical conductivity were found to grow with increasing temperature at all frequencies. The permittivity decreases and the electrical conductivity increases (by several orders of magnitude) with increasing frequency. Maxima were observed in the σ=f(T) and tanδ=f(T) curves for all frequencies; the maxima shift toward higher temperatures with increasing frequency.     

Production of ultrafine particles of high-temperature tetragonal WO<Subscript>3</Subscript> by dc arc discharge in Ar–O<Subscript>2</Subscript> gases

Ultrafine particles of WO₃ are successfully produced by dc arc discharge in Ar-O₂ gases. Particle sizes are distributed from 10 nm to 1 m depending on production conditions: gas pressure, collection position and discharge current. Observations of the cooled particles by electron microscopy indicate that the WO₃ particles are tetragonal, a phase that is usually only stable above 725 °C. The octahedral crystals are bounded by eight {1 0 1} faces and occasionally truncated by {1 0 0} and/or {0 0 1} faces. This method of producing WO₃ by dc arc discharge therefore affords a high-temperature phase that is preserved upon cooling to room temperature.     

μSR study of Eu<Subscript>0.8</Subscript>Ce<Subscript>0.2</Subscript>Mn<Subscript>2</Subscript>O<Subscript>5</Subscript> and EuMn<Subscript>2</Subscript>O<Subscript>5</Subscript> multiferroics

A comparative μSR study of ceramic samples of the EuMn₂O₅ and Eu_0.8Ce_0.2Mn₂O₅ multiferroics is performed in the temperature range from 15 to 300 K. It is found that the Ce doping of the EuMn₂O₅ sample slightly reduces the temperature of the magnetic phase transition from T _N = 45 K for the EuMn₂O₅ sample to T _N = 42.5 K for the Eu_0.8Ce_0.2Mn₂O₅ sample. Below the temperature T _N for both samples, there are two types of localization of a thermalized muon with different temperature dependences of the precession frequency of the magnetic moment of the muon in an internal magnetic field. The higher frequency in both samples refers to the initial antiferromagnetic matrix. The behavior of this frequency in Eu_0.8Ce_0.2Mn₂O₅ follows the Curie–Weiss law with the exponent β = 0.29 ± 0.02, which differs from the value β = 0.39 standard for 3D Heisenberg magnetics and is observed in EuMn₂O₅, because of the strong frustration of the doped sample. The temperature-independent low frequency is due to the presence of Mn³⁺–Mn⁴⁺ ferromagnetic pairs located along the b axis of the antiferromagnetic matrix and in the regions of phase separation, which contain such ion pairs and e _g electrons recharging them. In both samples, polarization losses are the same (about 20%) and are associated with the formation of Mn⁴⁺–Mn⁴⁺ + Mu complexes near Mn³⁺–Mn⁴⁺ ferromagnetic pairs. In the temperature interval from 25 to 45 K, the separation of the Eu_0.8Ce_0.2Mn₂O₅ structure into two fractions where the relaxation rates of polarization of muons differ by an order of magnitude is revealed. This effect is due to a change in the state of regions of phase separation (1D superlattices) at the indicated temperatures. Such effect in EuMn₂O₅ is significantly weaker.     

Study of the KNO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system by differential scanning calorimetry

The structural and the thermodynamic properties of potassium nitrate KNO₃ and its composites with nanosized aluminum oxide Al₂O₃ have been studied by differential scanning calorimetry. It has been found that an amorphous phase forms in composites (1–x)KNO_3–xAl₂O₃. The thermal effect corresponding to this phase has been observed at 316°C. It has been found that the phase transition heats of potassium nitrate decreased as the aluminum oxide fraction increased.     

Dielectric response of SrTiO<Subscript>3</Subscript>–SrMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript> solid solutions in the terahertz–infrared range

The reflection and transmission spectra of ceramic samples of SrTiO₃–SrMg_1/3Nb_2/3O₃ solid solutions have been measured in the frequency range of 5–5000 cm^–1 and in the temperature range of 5–370 K. Based on these spectra, the spectra of the real ε'(ν) and imaginary ε''(ν) parts of the complex permittivity ε*(ν) have been simulated by the method of dispersion analysis. It has been found that the temperature evolution of the dielectric constant is entirely determined by the behavior of the soft mode.     

Luminescence centers in α-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramics

Luminescence photoexcitation spectra of α-Bi₂O₃ ceramics are investigated. Luminescence spectra were deconvoluted into fundamental components using the Alentsev-Fok method. It is established that the luminescence spectra of α-Bi₂O₃ ceramics consist of three fundamental bands with maxima at 2.75, 2.40, and 1.97 eV. A comparison of the results with those from an investigation of luminescence of various modifications of bismuth oxide and bismuth germanates suggests that luminescence of these compounds is caused by radiation processes that occur in structural complexes that contain the bismuth ion in a nearest oxygen environment. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 5, pp. 672–676, September–October, 2008.     

Electrical conductivity and electric polarization in In<Subscript>2</Subscript>O<Subscript>3 − δ</Subscript>: Sr at different oxygen contents

The electrical characteristics of strontium-doped indium oxide have been experimentally investigated in the case of deviations from the stoichiometric composition with respect to oxygen. Doping considerably decreases the electrical conductivity of In₂O₃ and makes it extremely highly sensitive to variations in the oxygen content. A small oxygen deficiency of the samples corresponds to the high-resistance state, which is formed as a result of the decrease in the concentration of charge carriers and the transparency of potential barriers at the grain boundaries. It has been found that the oxygen deficiency in In₂O_{3 − δ}: Sr restores a high n-type electrical conductivity, which is consistent with the concepts of oxygen vacancies as shallow donors. For a sufficient oxygen deficiency, the potential barriers do not manifest themselves; however, as the oxygen content increases, there arises a potential relief that leads to a set of remarkable effects: the specific nonlinearity and hysteresis of the current-voltage characteristic, which are caused by the tunneling transparent potential barriers; an increase in the permittivity to 13.3 at a frequency of 10⁵ Hz and at a temperature T = 77 K; and the temperature anomalies of the measured parameters, which are associated with the topological phase transition to a spatially inhomogeneous conductance of the samples. It has been revealed that, for small deviations from the stoichiometric composition with respect to oxygen, not only the active component but also the capacitive component of the conductance of In₂O_{3 − δ}: Sr exhibit a sensitivity to the pressure and composition of the gas medium.     

Size-controllable synthesis of functional heterostructured TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> core–shell nanoparticles

Mono and bicomponent TiO₂ and WO₃ nanoparticles were synthesized inside Vycor^® glass pores, by cycles of impregnation of the glass with the respective oxide precursor followed by its thermal decomposition. The impregnation-decomposition cycle (IDC) methodology promoted a linear mass increase of the glass matrix, and allowed tuning the nanoparticle size. X-ray diffraction and Raman spectroscopy data allowed identifying the formation of TiO₂ as anatase phase, while WO₃ is a mixture of the γ-WO₃ (monoclinic) and δ-WO₃ (triclinic) phases. High resolution transmission electron microscopy images revealed that for 3, 5, and 7 IDC, the TiO₂ nanoparticles obtained presented average diameters of 3.4, 4.3, and 5.1 nm, and the WO₃ nanoparticles have 2.9, 4.6, and 5.7 nm sizes. These TiO₂ and WO₃ monocomponent nanoparticles were submitted to IDC with the other oxide precursor, resulting in bicomponent nanoparticles. The broadening and shift of the Raman bands related to titanium and tungsten oxides suggest the formation of hetero-structure core–shell nanoparticles with tunable core sizes and shell thicknesses.