Electrochemical Sensor Based on Oxidation of 2,8‐Dihydroxyadenine to Monitor DNA Damage in Calf Thymus DNA

A novel and reliable direct electrochemical method has been established to monitor DNA damage in acid hydrolyzed calf thymus DNA, based on the determination of 2,8‐dihydroxyadenine (2,8‐DHA). A single‐wall carbon nanotubes (SWCNT) modified edge plane pyrolytic graphite electrode (EPPGE) has been used as a sensor to monitor the DNA damage. 2,8‐DHA the main in vivo adenine oxidation product undergoes oxidation at ～395 mV at SWCNT modified EPPGE using square wave voltammetry (SWV). The sensor exhibits potent and persistent electron‐mediating behavior. A well‐defined oxidation peak for the oxidation of 2,8‐DHA was observed at modified electrode with lowering of peak potential and increase in peak current as compared to bare EPPGE. At optimal experimental conditions, the catalytic oxidative peak current was responsive with the 2,8‐DHA concentrations ranging from 0.05 nM to 100 nM. The detection limit was 3.8×10^?11 M and limit of quantification was 1.27×10^?10 M. The modified electrode exhibited high stability and reproducibility.     

Simultaneous voltammetric determination of prednisone and prednisolone in human body fluids

A sensitive, rapid and reliable electrochemical method based on voltammetry at single wall carbon nanotube (SWNT) modified edge plane pyrolytic graphite electrode (EPPGE) is proposed for the simultaneous determination of prednisolone and prednisone in human body fluids and pharmaceutical preparations. The electrochemical response of both the drugs was evaluated by osteryoung square wave voltammetry (OSWV) in phosphate buffer medium of pH 7.2. The modified electrode exhibited good electrocatalytic properties towards prednisone and prednisolone reduction with a peak potential of ∼−1230 and ∼−1332 mV respectively. The concentration versus peak current plots were linear for both the analytes in the range 0.01-100 μM and the detection limit (3σ/slope) observed for prednisone and prednisolone were 0.45 × 10⁻⁸, 0.90 × 10⁻⁸ M, respectively. The results of the quantitative estimation of prednisone and prednisolone in biological fluids were also compared with HPLC and the results were in good agreement.     

Cloud point extraction for the determination of cadmium and lead employing sequential multi-element flame atomic absorption spectrometry

A cloud point extraction procedure for pre-concentration and determination of cadmium and lead in drinking water using sequential multi-element flame atomic absorption spectrometry is described. 4-(2-thiazolylazo)-orcinol (TAO) has been used as complexing agent and the micellar phase was obtained using the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114) and centrifugation. The conditions for reaction and extraction (surfactant concentration, reagent concentration, effect of incubation time, etc) were studied and the analytical characteristics of the method were determined. The method allows the determination of cadmium and lead with quantification limits of 0.30?µg?L^?1 and 2.6?µg?L^?1, respectively. A precision expressed as relative standard deviation (RSD, n?=?10) of 2.3% and 2.6% has been obtained for cadmium concentrations of 10?µg?L^?1 and 30?µg?L^?1, respectively, and RSD of 1.3% and 1.7% for lead concentrations of 10?µg?L^?1 and 30?µg?L^?1, respectively. The accuracy was confirmed by analysis of a natural water certified reference material. The method has been applied for the determination of cadmium and lead in drinking water samples collected in the cities of Ilhéus and Itabuna, Brazil. Recovery tests have also been performed for some samples, and results varied from 96 to 105% for cadmium and 97 to 106% for lead. The cadmium and lead concentrations found in these samples were always lower than the permissible maximum levels stipulated by World Health Organization and the Brazilian Government.     

A comparison of edge- and basal-plane pyrolytic graphite electrodes towards the sensitive determination of hydrocortisone

Electrochemical sensor employing edge-plane pyrolytic graphite electrode (EPPGE) for the sensitive detection of hydrocortisone (HC) is delineated for the first time. The electrochemical properties are investigated exercising the cyclic voltammetry and square-wave voltammetry (SWV). When equating with the bare basal-plane pyrolytic graphite electrode (BPPGE), the EPPGE gave better response towards the detection of HC both in terms of sensitivity and detection limit. The voltammetric results indicated that EPPGE remarkably enhances the reduction of HC which leads to considerable amelioration of peak current with shift of peak potential to less negative values. The difference in the surface morphology of two electrodes has been studied. Also, the EPPGE delivered an analytical performance for HC with a sensitivity of 45 nA nM⁻¹ and limit of detection of 88 nM in the concentration range 100-2000 nM. The method has been utilized for the determination of HC in pharmaceuticals and real samples. The electroanalytical method using EPPGE is the most sensitive method for determination of HC with lowest limit of detection to date. The major metabolites present in blood plasma did not intervene with the present investigation as they did not exhibit reduction peak in the experimental range used. A comparison of results with high performance liquid chromatography (HPLC) signalizes a good agreement.     

Electrochemical investigations of corticosteroid isomers—testosterone and epitestosterone and their simultaneous determination in human urine

Voltammetric investigation of two corticoid isomers—testosterone and epitestosterone has been carried out at bare and single-wall carbon nanotubes (SWNT)-modified edge plane pyrolytic graphite electrode (EPPGE). Square wave voltammetry (OSWV) has been used for the simultaneous determination of isomeric steroids. The reduction of the two isomers occurred in a pH dependent, 2e, 2H⁺ process and well-defined voltammetric peaks were observed. Under the optimum experimental conditions, linear calibration curves are obtained within the concentration range 5-1000 nM for both the steroids with the limit of detection 2.8 × 10⁻⁹ and 4.1 × 10⁻⁹ M for testosterone and epitestosterone respectively. The developed protocol is successfully implemented for the analysis of both the compounds in the urine samples of normal subjects as well as in patients undergoing treatment with testosterone. The results obtained from the proposed voltammetric method were also compared with HPLC analysis and found to be similar.     

Elemental Analysis of Tarhana by Microwave Induced Plasma Atomic Emission Spectrometry

Elemental analysis of tarhana, a traditional Turkish cereal soup, has been conducted. A new method was developed for the determination of calcium, iron, magnesium, manganese, potassium, and sodium, in tarhana by microwave induced plasma atomic emission spectrometry. A sample of 0.1?g were mineralized by microwave digestion in 10?mL of 65% HNO₃. A wheat flour standard reference material (GBW 08503) was used for validation. Linear calibration using standards prepared in acid was conducted for all determinations. The limits of detection were 1.21?µg?g^?1 for Ca at 393.366?nm, 0.43?µg?g^?1 for Fe at 259.940?nm, 11.5?µg?g^?1 for K at 766.491?nm, 0.12?µg?g^?1 for Mg at 285.213?nm, 0.04?µg?g^?1 for Mn at 403.076?nm, and 0.04?µg?g^?1 for Na at 588.995?nm. Ca, K, Fe, Mg, Mn, and Na were determined in tarhana with values from 0.73 to 1.61, 0.016 to 0.061, 2.02 to 4.09, 0.473 to 1.414, 0.019 to 0.043, and 0.26 to 1.83?mg?g^?1, respectively.     

Differential pulse polarographic behaviour of thiazopyr herbicide and application to its determination in fruit juice and soil samples

A differential pulse polarographic method for the determination of the herbicide thiazopyr has been developed. The polarographic study of thiazopyr exhibited two well-defined cathodic peaks within the pH range of 1.0 to 8.0. The variation of pH and polarographic parameters indicated that the optimum conditions under which thiazopyr could be reduced were a pH 7.0 BR buffer solution, a reduction peak potential of ?1270 mV (vs. SCE), scan rate of 5 mV s^?1, pulse amplitude of 50 mV with pulse duration of 50 ms at an ambient temperature of 25 ± 3°C. The main reduction peak was characterised by cyclic voltammetry as being irreversible and diffusion-controlled. A linear relationship between the peak current and the concentration of thiazopyr was obtained in the range of 0.43–38.6 µg mL^?1, with a detection limit of 0.127 µg mL^?1. The proposed method was successfully applied to the determination of thiazopyr in spiked fruit juice and soil samples. The mean recoveries of the 19.8 µg g^?1 and 3.96 µg mL^?1 thiazopyr spiked to soil and orange juice were 20.2 ± 1.0 µg g^?1 and 3.84 ± 0.12 µg mL^?1, at 95% confidence level, respectively. The sufficiently good recoveries and low relative standard deviation (RSD) data confirm the high accuracy and precision of the proposed method. The interferences effects of several commonly used pesticides and inorganic species were also studied. Interfering effects were eliminated either by providing selectivity with pH, or using EDTA as complexing agent.     

Highly sensitive inhibitory kinetics fluorescence method for determination of arsenic

A new and highly sensitive inhibitory kinetic fluorescence method for the determination of arsenic (III) has been established based on its inhibitory effect on the oxidation reaction of Acridine red (ADR) by KBrO₃ in sulphuric acid medium. The reaction has been followed by measuring the enhancement of fluorescence at 550?nm. It relies on the linear relationship where the change in the fluorescence (ΔF) versus added As(III) amounts in the range of 0–0.450?µg?mL^?1 is plotted, under the optimum conditions. The sensitivity of the proposed method, i.e. the limit of detection, is 2.1?×?10^?2?ng?mL^?1. The method is featured with good accuracy and reproducibility for arsenic (III) determination. This method was successfully applied for the quantitative determination of arsenic (III) in food products samples, and the relative standard deviations and the recoveries were in ranges of 2.31–2.83% and 90.0–107.2%, respectively. A review of recently published catalytic or inhibiting kinetic methods for the determination of arsenic (III) has also been presented for comparison. The mechanism of reaction was studied.     

A single-wall carbon nanotubes modified edge plane pyrolytic graphite sensor for determination of methylprednisolone in biological fluids

An electrochemical protocol based on reduction is developed to determine methylprednisolone using single-wall carbon nanotubes (SWNTs) modified edge plane pyrolytic graphite electrode (EPPGE). To obtain a good sensitivity, instrumental variables were studied using Square Wave Voltammetry (SWV). The voltammetric results indicate that SWNTs modified EPPGE remarkably enhances the reduction of methylprednisolone which leads to considerable improvement of peak current with shift of peak potential to less negative values. The voltammetric current showed a linear response for methylprednisolone concentration in the range 5-500 nM with a sensitivity of 98 nA nM⁻¹. The limit of detection was estimated to be 4.5 × 10⁻⁹ M. The developed method is used for the determination of methylprednisolone in pharmaceutical dosages and human blood plasma samples of patients undergoing treatment with methylprednisolone. The major metabolites present in blood plasma did not interfere with the present investigation as they did not exhibit reduction peak in the experimental range used. A comparison of results with high performance liquid chromatography (HPLC) indicates a good agreement.     

Enhanced Specificity and Sensitivity for the Determination of Nickel(II) by Square-wave Adsorptive Cathodic Stripping Voltammetry at Disposable Graphene-modified Pencil Graphite Electrodes

Chemical sensors relying on graphene-based materials have been widely used for electrochemical determination of metal ions and have demonstrated excellent signal amplification. This study reports an electrochemically reduced graphene oxide (ERGO)/mercury film (HgF) nanocomposite-modified pencil graphite electrode (PGE) prepared through successive electrochemical reduction of graphene oxide (GO) sheets and an in situ plated HgF. The ERGO-PG-HgFE, in combination with dimethylglyoxime (DMG) and square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV), was evaluated for the determination of Ni²⁺ in tap and natural river water samples. A single-step electrode pre-concentration approach was employed for the in situ Hg-film electroplating, metal-chelate complex formation, and non-electrolytic adsorption at –0.7 V. The current response due to nickel-dimethylglyoxime [Ni(II)-DMG₂] complex reduction was studied as a function of experimental paratmeters including the accumulation potential, accumulation time, rotation speed, frequency and amplitude, and carefully optimized for the determination of Ni²⁺ at low concentration levels (μg?L^?1) in pH 9.4 of 0.1 M NH₃–NH₄Cl buffer. The reduction peak currents were linear with the Ni²⁺ concentration between 2 and 16?μg?L^?1. The limits of detection and quantitation were 0.120?±?0.002?µg?L^?1 and 0.401?±?0.007?µg?L^?1 respectively, for the determination of Ni²⁺ at an accumulation time of 120?s. The ERGO-PG-HgFE further demonstrated a highly selective stripping response toward Ni²⁺ determination compared to Co²⁺. The electrode was found to be sufficiently sensitive to determine metal ions in water samples at 0.1?µg?L^?1, well below the World Health Organization standards.     

Electropolymerized Diphenylamine on Functionalized Multiwalled Carbon Nanotube Composite Film and Its Application to Develop a Multifunctional Biosensor

Diphenylamine (DPA) monomers have been electropolymerized on the amino‐functionalized multiwalled carbon nanotube (AFCNT) composite film modified glassy carbon electrode (GCE) by cyclic voltammetry (CV). The surface morphology of PDPA‐AFCNT was studied using field‐emission scanning electron microscopy (FE‐SEM). The interfacial electron transfer phenomenon at the modified electrode was studied using electrochemical impedance spectroscopy (EIS). The PDPA‐AFCNT/GCE represented a multifunctional sensor and showed good electrocatalytic behavior towards the oxidation of catechol and the reduction of hydrogen peroxide. Rotating‐disk electrode technique was applied to detect catechol with a sensitivity of 1360 µA mM^?1 cm^?2 and a detection limit of 0.01 mM. Amperometric determination of hydrogen peroxide at the PDPA‐AFCNT film modified electrode results in a linear range from 10 to 800 µM, a sensitivity of 487.1 µA mM^?1 cm^?2 and detection limit of 1 µM. These results show that the nano‐composite film modified electrode can be utilized to develop a multifunctional sensor.     

Determination of carbendazim and thiabendazole in apple juice by hollow fibre-based liquid phase microextraction-high performance liquid chromatography with fluorescence detection

A hollow fibre-based liquid phase microextraction (HF-LPME) coupled with high performance liquid chromatography with fluorescence detection (HPLC-FD) method was developed for the determination of carbendazim (MBC) and thiabendazole (TBZ) in apple juice. Some important extraction parameters, such as the pH of the sample solution, extraction time, stirring rate and salt concentration, were optimised. As a result, the optimal HF-LPME conditions were selected as follows: A 4?mL of sample solution (donor phase) at pH of 7.5 was used for the extraction. The pores of the hollow fibre were impregnated by 1-octanol, and 5?mM HCl (pH?=?2.5) was used as the extraction solvent. The extractions were conducted at a stirring rate of 800?rpm for 40?min. After extraction, 10?µL of the extraction solvent was injected into the HPLC system for analysis. The average enrichment factors were 106 and 114 for MBC and TBZ, respectively. A good linear relationship existed in the range of 2.5?～?500?µg?L^?1 and 5?～?500?µg?L^?1for MBC and TBZ in apple juice with the correlation coefficients (r) of 0.9995 and 0.9991, respectively. The limits of detection were 0.8?µg?L^?1 for MBC and 1.5?µg?L^?1 for TBZ (S/N?=?3?:?1). The recoveries of the method were between 86.3% and 106.0% with the relative standard deviations (RSDs) ranging from 3.3% to 8.5%. The HF-LPME-HPLC method has been successfully applied to the analysis of MBC and TBZ in apple juice, indicating that LPME-HPLC may be a promising combination for the analysis of pesticide residues for some food samples.     

Electrocatalytic Oxidation of Diethylaminoethanethiol and Hydrazine at Single‐walled Carbon Nanotubes Modified with Prussian Blue Nanoparticles

In this work, edged plane pyrolytic graphite electrode EPPGE was modified with functionalised single‐walled carbon nanotubes and Prussian blue nanoparticles (PB). The modified electrode was characterised by techniques such as TEM, FTIR, XPS, EDX and cyclic voltammetry. The EPPGE‐SWCNT‐PB platform exhibited enhanced electron transport and catalytic efficiency towards the oxidation of Diethylaminoethanethiol (DEAET) and hydrazine compared with the other electrodes studied. The EPPGE‐SWCNT‐PB showed good electrochemical stability in the analytical solution, showing limit of detection in the micromolar range and catalytic rate constant of 3.71×10⁶ and 7.56×10⁶ cm³ mol^?1 s^?1 for DEAET and hydrazine respectively. The adsorption properties of these analytes that impact on their detection at the SWCNT‐PB film modified electrode were evaluated and discussed.     

Sensitive determination of Fenamiphos in water samples by flow injection photoinduced chemiluminescence

In this work, a sensitive flow injection chemiluminescence (FI-CL) method for the determination of nematicide Fenamiphos in a rapid and simple way is proposed. Fenamiphos is first photodegraded in basic medium. These photofragments react with Ce(IV) providing the chemiluminescence signal. To the authors’ knowledge, no chemiluminescence method has been described in the literature for the determination of the nematicide Fenamiphos. All physical and chemical parameters in the flow injection chemiluminescence system were optimized in order to obtain the best sensitivity, selectivity and sample throughput. Before the injection of the sample in the FI-CL system, a preconcentration step with solid phase extraction C18 cartridges was performed. By applying solid phase extraction (SPE) to 250?mL of standard (final volume 10?mL), the linear dynamic range was between 3.4 and 60?µg?L^?1, and the detection limit was 1?µg?L^?1. When SPE was applied to 500?mL of standard (final volume 10?mL), the detection limit was 0.5?µg?L^?1. These detection limits are below the emission limit value established by the Spanish Regulations of the Hydraulic Public Domain for pesticides (50?µg?L^?1) and of the same order as the limit established for total pesticides (0.5?µg?L^?1) at European Directive on the quality of water for human consumption. The sample throughput was 126 hour^?1. Intraday and interday coefficients of variation were below 10% in all cases. No interference was registered in presence of usual concentrations of anions, cations and other organophosphorus pesticides. The method was successfully applied to the analysis of environmental water samples, obtaining recoveries between 96 and 107.5%.     

Square wave voltammetric determination of diafenthiuron and its application to water,soil and insecticide formulation

A square wave cathodic stripping voltammetric (SWCSV) method has been developed for the determination of insecticide diafenthiuron. The procedure is based on controlled accumulation of the insecticide on a static hanging mercury drop electrode (SHMDE) at 0.00?mV (vs. Ag/AgCl) in Britton-Robinson buffer solution (pH 7.0). The insoluble mercury compound was reduced at ?510?mV during the cathodic potential scan. The peak currents were linearly related to insecticide concentration between 30.4 and 3200?µg?L^?1 . The detection and quantification limit were 9.1?µg?L^?1 and 30.4?µg?L^?1, respectively. The proposed analytical procedure was applied to natural water and soil samples. The method was extended to direct determination of diafenthiuron in insecticide formulation Polo® 50 WP and average content of 50.3?±?1.7 (m/m) at 90% confidence level, in close agreement with the 50.0% quoted by the manufacturer. HPLC comparison method indicated that accuracy was in agreement with that obtained by the proposed method.     

Sensitive Simultaneous Determination of o-Nitrophenol and p-Nitrophenol in Water by Surfactant-Mediated Differential Pulse Voltammetry

A simple, low-cost and sensitive electroanalytical method was developed for the simultaneous determination of p-nitrophenol and o-nitrophenol isomers in water samples at a glassy carbon electrode (CGE) in the presence of cationic surfactant. The electrochemical behavior of p-nitrophenol and o-nitrophenol was studied by cyclic voltammetry (CV) in 0.1?mol L^?1 acetate/acetic acid buffer (pH 3.70) in the presence and absence of cetylpyridinium bromide. The resolution of overlapped cathodic peaks potentials (E_pc) of isomers was successfully improved in the presence of 100.0?µmol L^?1 cetylpyridinium bromide, thus making this approach ideal for the simultaneous determination of isomers. Under the optimized conditions in 0.05?mol L^?1 HEPES buffer at pH 7.0 using differential pulse voltammetry (DPV) at a scan rate of 45?mV s^?1, pulse amplitude of 220?mV and modulation time of 10?ms, limits of detection 0.59?µmol L^?1 for p-nitrophenol and 1.14?µmol L^?1 for o-nitrophenol were obtained with linear ranges from 2.0 to 60.0?µmol L^?1 and 3.0 to 60.0?µmol L^?1, respectively. The intraday precision was assessed as relative standard deviation (%) for 20.0 and 40.0?µmol L^?1 concentrations were 4.30% and 2.41% for p-nitrophenol and 4.87% and 2.20% for o-nitrophenol, respectively. The developed method was applied for the determination of the isomers in lake water samples. The accuracy was attested by comparison with high-performance liquid chromatography with diode array detection (HPLC-DAD) as a reference analytical technique. Recovery values ranging from 90.3% to 111.8% also attested to the accuracy of method for analysis of real samples.     

Determination of ultratrace lead with bismuth film electrodes based on magneto-voltammetry

A novel method for the determination of Pb²⁺ with bismuth film electrodes (BFEs) based on magneto-voltammetry was investigated. In the presence of a 0.6?T external magnetic field, square wave voltammetry of Pb²⁺ was performed with BFEs. A high concentration of Fe³⁺ was added to the analytes to generate a large cathodic current during the preconcentration step. A Lorentz force from the flux of net current through the magnetic field resulted in convection. Then, more Pb²⁺ deposited onto the electrode and larger stripping peak currents were observed. BFEs that were prepared by simultaneously depositing the bismuth and Pb²⁺ on an electrode offered a mercury-free environment for this determination. This method exhibits a high sensitivity of 4.61?µA?µM^?1 for Pb²⁺ over the 1?×?10^?8 to 1?×?10^?6?M range. A detection limit as low as 8.5?×?10^?10?M was obtained with only 1-min preconcentration. The method was successfully applied to determine Pb²⁺ in real water samples.     

A Novel Method for the Determination of Streptomycin Using Sodium Nitroprusside as a Chromogenic Reagent by Spectrophotometry

Abstract

A rapid and simple spectrophotometric method for the determination of streptomycin has been developed and validated. The method was based on the reaction of streptomycin with sodium nitroprusside in the alkaline medium forming a red product measured at the maximum absorption of 495 nm. The stoichiometric ratio of the product is 1:1. Beer's law is obeyed in a range of 1.87 µg mL^?1 ～ 279.8 µg mL^?1 of streptomycin and ?₄₉₅ is 6.0 × 10³ L·mol^?1 cm^?1.Under the optimum condition, the equation of linear regression is A = 0.00742 + 0.05683 C (× 10⁵ mol·L^?1), with a linear correlation coefficient of 0.9990. The detection limit (3σ/k) is 0.96 µg mL^?1, the relative standard deviation (RSD) is 2.40%, and the average recovery rate is 98.3%–102.7%. Every parameter has been optimized, and the reaction mechanism has been studied. The proposed method has been successfully applied to the determination of streptomycin for injections and tablets of pharmaceutical preparation. Analytical results obtained by this new method were very gratifying.     

Spectrophotometric Determination of Hydrazine

Abstract

A simple sensitive and selective method is described for the determination of trace amounts of hydrazine. The method is based on the reduction of nitrate to nitrite. Hydrazine in ammoniacal condition is used as reducing agent with copper(II) as catalyst. The nitrite prepared is determined based on the diazo coupling reaction between p‐nitroaniline and N‐(1‐naphthyl)ethylenediammine dihydrochloride(NEDA). The method obeys Beer's law in the concentration range of 0–15 µg of hydrazine in a sample volume of 10 ml at 545 nm and the colour is stable for 3 h. The molar absorptivity is calculated to be 3.83×10⁴ l/mol/cm with a correlation coefficient of 0.999. The relative standard deviation is 1.8% (n=10) at 12 µg of hydrazine. Interferences due to foreign ions have been studied and the method has been applied for the determination of hydrazine in boiler feed water.     

Electrochemical Determination of Uric Acid Using a Multiwalled Carbon Nanotube Platinum–Nickel Alloy Glassy Carbon Electrode

Platinum–nickel nanoparticles were synthesized by a reduction procedure. The Pt–Ni/C composite was characterized by X-ray diffraction, infrared spectroscopy, transmission electron microscopy, and electrochemical analysis. The measurements show that the Pt–Ni/multiwalled carbon nanotubes provided higher electrocatalytic activity for the oxidation of uric acid than Pt–Ni/carbon black. The sensor prepared from the characterized material provided a long linear dynamic range from 0.1 to 240.4?µM with a detection limit of 0.03?µM and a sensitivity of 41.21?µA?mM^?1?cm^?2. The reported modified electrode also provided excellent selectivity, good stability, and satisfactory reproducibility for the determination of uric acid.