Electrical properties of diamond surfaces functionalized with molecular monolayers

Recent studies have shown that semiconductor surfaces such as silicon and diamond can be functionalized with organic monolayers, and that these monolayer films can be used to tether biomolecules such as DNA to the surfaces. Electrical measurements of these interfaces show a change in response to DNA hybridization and other biological binding processes, but the fundamental nature of the electrical signal transduction has remained unclear. We have explored the electrical impedance of polycrystalline and single-crystal diamond surfaces modified with an organic monolayer produced by photochemical reaction of diamond with 1-dodecene. Our results show that, by measuring the impedance as a function of frequency and potential, it is possible to dissect the complex interfacial structure into frequency ranges where the total impedance is controlled by the molecular monolayer, by the diamond space-charge region, and by the electrolyte. The results have implications for understanding the ability to use molecularly modified semiconductor surfaces for applications such as chemical and biological sensing.     

Interfacial electrical properties of DNA-modified diamond thin films: intrinsic response and hybridization-induced field effects

We have investigated the frequency-dependent interfacial electrical properties of nanocrystalline diamond films that were covalently linked to DNA oligonucleotides and how these properties are changed upon exposure to complementary and noncomplementary DNA oligonucleotides. Frequency-dependent electrical measurements at the open-circuit potential show significant changes in impedance at frequencies of >10(4) Hz when DNA-modified diamond films are exposed to complementary DNA, with only minimal changes when exposed to noncomplementary DNA molecules. Measurements as a function of potential show that at 10(5) Hz, the impedance is dominated by the space-charge region of the diamond film. DNA molecules hybridizing at the interface induce a field effect in the diamond space-charge layer, altering the impedance of the diamond film. By identifying a range of impedances where the impedance is dominated by the diamond space-charge layer, we show that it possible to directly observe DNA hybridization, in real time and without additional labels, via simple measurement of the interfacial impedance.     

Frequency-dependent electrical detection of protein binding events

Frequency-dependent electrochemical impedance spectroscopy has been used to characterize the changes in electrical response that accompany specific binding of a protein to its substrate, using the biotin-avidin system as a model. Our results show that avidin, at concentrations in the nanomolar range, can be detected electrically in a completely label-free manner under conditions of zero average current flow and without the use of any auxiliary redox agents. Impedance measurements performed on biotin-modified surfaces of gold, glassy carbon, and silicon were obtained over a wide frequency range, from 5 mHz to 1 MHz. On each biotin-modified surface, binding of avidin is most easily detected at low frequencies, <1 Hz. Electrical circuit modeling of the interface was used to relate the frequency-dependent electrical response to the physical structure of the interface before and after avidin binding. Electrical measurements were correlated with measurements of protein binding using fluorescently labeled avidin.     

Functional monolayers for improved resistance to protein adsorption: oligo(ethylene glycol)-modified silicon and diamond surfaces

The interaction of proteins with semiconductors such as silicon and diamond is of great interest for applications such as electronic biosensing. We have investigated the use of covalently bound oligo(ethylene glycol), EG, monolayers on diamond and silicon to minimize nonspecific protein adsorption. Protein adsorption was monitored by fluorescence scanning as a function of the length of the ethylene glycol chain (EG3 through EG6) and the terminal functional group (methyl- versus hydroxyl-terminated EG3 monolayer). More quantitative measurements were made by eluting adsorbed avidin from the surface and measuring the intensity of fluorescence in the solution. The attachment chemistry of the tri(ethylene glycol) molecules and monolayer orientation was studied by X-ray photoelectron spectroscopy. Improvement in the selectivity of surfaces modified with EG functionality was demonstrated in two model biosensing assays. We find that high-quality EG monolayers are formed on silicon and diamond and that these EG3 monolayers are as effective as EG3 self-assembled monolayers on gold at resisting nonspecific avidin adsorption. These results show promise for use of silicon and diamond materials in many potential applications such as biosensing and medical implants.     

Tandem "click" reactions at acetylene-terminated Si(100) monolayers

We demonstrate a simple method for coupling alkynes to alkynes. The method involves tandem azide-alkyne cycloaddition reactions ("click" chemistry) for the immobilization of 1-alkyne species onto an alkyne modified surface in a one-pot procedure. In the case presented, these reactions take place on a nonoxidized Si(100) surface although the approach is general for linking alkynes to alkynes. The applicability of the method in the preparation of electrically well-behaved functionalized surfaces is demonstrated by coupling an alkyne-tagged ferrocene species onto alkyne-terminated Si(100) surfaces. The utility of the approach in biotechnology is shown by constructing a DNA sensing interface by derivatization of the acetylenyl surface with commercially available alkyne-tagged oligonucleotides. Cyclic voltametry, electrochemical impedance spectroscopy, X-ray photoelectron spectroscopy, and X-ray reflectometry are used to characterize the coupling reactions and performance of the final modified surfaces. These data show that this synthetic protocol gives chemically well-defined, electronically well-behaved, and robust (bio)functionalized monolayers on silicon semiconducting surfaces.     

Diamond Based Biosensors: Surface-Fluid Interaction Issues

The interaction of nanocrystalline (NCD) and microcrystalline (MCD) p-type semiconducting diamond surfaces with phosphate buffer saline (PBS), simulated body fluid (SBF) and bovine serum albumin (BSA) solutions under applied electric potentials is the main subject of this work. The effect of these fluids on the electrical resistivity of the diamond surface is evaluated. Furthermore, the interaction effects of these surfaces with BSA containing SBF solution during 30 days, is addressed.The electrical measurements have shown that the electrical current passing through the NCD samples is influenced by the fluid's ionic composition, whereas no variation was detected for the MCD samples. Both NCD and MCD surfaces favor the formation of a deposit layer after 30 days in contact with SBF+BSA solution. This deposit is mainly composed of Ca, P, Mg and O, containing also a significant concentration of BSA proteins.     

Electrical bias dependent photochemical functionalization of diamond surfaces

Diamond is an excellent substrate for many sensing and electronic applications because of its outstanding stability in biological and aqueous environments. When the diamond surface is H-terminated, it can be covalently modified with organic alkenes using wet photochemical methods that are surface-mediated and initiated by the ejection of electrons from the diamond. To develop a better understanding of the photochemical reaction mechanism, we examine the effect of applying an electrical bias to the diamond samples during the photochemical reaction. Applying a 1 V potential between two diamond electrodes significantly increases the rate of functionalization of the negative electrode. Cyclic voltammetry and electrochemical impedance measurements show that the 1 V potential induces strong downward band-bending within the diamond film of the negative electrode. At higher voltages a Faradaic current is observed, with no further acceleration of the functionalization rate. We attribute the bias-dependent changes in rate to a field effect, in which the applied potential induces a strong downward band-bending on the negative electrode and facilitates the ejection of electrons into the adjacent fluid of reactant organic alkenes. We also demonstrate the ability to directly photopattern the surface with reactant molecules on length scales of <25 microm, the smallest we have measured, using simple photomasking techniques.     

Potential driven deposition of poly(diallyldimethylammonium chloride) onto the surface of 3-mercaptopropionic acid monolayers assembled on gold

Electrochemical impedance spectroscopy (EIS) and quartz crystal microbalance (QCM) measurements are used to examine the ability of applied potential to drive the ionic self-assembly of poly(diallyldimethylammonium) chloride (PDDA) onto a substrate modified with a monolayer of 3-mercaptopropionic acid (3-MPA). The potential of zero charge (PZC) of the gold electrode modified with a monolayer of 3-MPA was found by differential capacitance measurements to be -0.12 (+/-0.01) V versus Ag-AgCl. Changing the substrate potential to values positive (-0.01 V vs Ag-AgCl) of the PZC induces interfacial conditions that are favorable for the electrostatic deposition of cationic polymers onto the surface of 3-MPA monolayers. This result is also consistent with experimental observations obtained when the 3-MPA-modified substrate is exposed to 0.10 mol L (-1) NaOH solutions. When potentials equal or negative to the PZC are applied to the substrate, no significant accumulation of the PDDA is found by either QCM or EIS measurement. This result is consistent with results obtained when the 3-MPA modified substrate is exposed to 0.10 mol L (-1) HCl solutions where no PDDA adsorption is expected because the monolayer is neutral under these conditions. Changes in the impedance and quartz crystal frequency obtained after potential is applied to the substrate are interpreted in terms of the applied potential creating interfacial conditions that are favorable for the deprotonation of the terminal carboxylic acid groups and the subsequent electrostatic assembly of the polycation onto the negatively charged monolayer.     

Bulk electrical properties of single-walled carbon nanotubes immobilized by dielectrophoresis: evidence of metallic or semiconductor behavior

We report the electrical characterization of single-walled carbon nanotubes (SWCNTs) trapped between two electrodes by dielectrophoresis (DEP). At high frequency, SWCNTs collected by DEP are expected to be of metallic type. Indeed current-voltage (I-V) measurements for devices made at 10 MHz show high values of conductivity and exhibit metallic behavior with linear and symmetric electrical features attributed to ohmic conduction. At low frequency, SWCNTs attracted by DEP are expected to be of semiconducting nature. Devices made at 10 kHz behave as semiconductors and demonstrate nonlinear and rectifying electrical characteristics with conductivities many orders of magnitude below the sample resulting from high-frequency immobilization of SWCNTs. Conducting atomic force microscopy (C-AFM) and current density calculation results are presented to reinforce results obtained by I-V measurements which clearly show type separation of SWCNTs after DEP experiments.     

Disubstituted polyacetylene brushes grown via surface-directed tungsten-catalyzed polymerization

Disubstituted polyacetylene brushes were grown from modified silicon and quartz surfaces using a transition metal-catalyzed polymerization technique employing tungsten hexachloride/tetraphenyl tin (WCl6/Ph4Sn). The substrate surfaces were initially functionalized with terminal alkyne functional groups by using an alkyne-functionalized silane, O-(propagyloxy)-N-(triethoxysilylpropyl) urethane, as a surface coupling agent. Surface polymerization of 5-decyne under microwave irradiation at 150 degrees C for 30 min was performed on the functional surfaces to produce surfaces consisting of grafted poly(1,2-dibutylacetylene) brushes. The alkyne-functionalized and polymer-coated surfaces were characterized using surface contact angle measurements, film thickness measurements, atomic force microscopy, and X-ray photoelectron spectroscopy, and fluorescence spectrometer measurements were performed to analyze the surfaces at each step of the modification process. This simple technique demonstrates a novel way of synthesizing a poly(1,2-dibutylacetylene) brush layer on silicon substrate, and it has future potential in the fabrication of selectively functionalized surfaces on the nanoscale via this new synthetic approach.     

Surface transfer doping of diamond: A review

Ultra-wide bandgap materials show great promise as a solution to some of the limitations of current state of the art semiconductor technology. Among these, diamond has exhibited great potential for use in high-power, high-temperature electronics, as well as sensing and quantum applications. Yet, significant challenges associated with impurity doping of the constrained diamond lattice remain a primary impediment towards the development of diamond-based electronic devices. An alternative approach, used with continued success to unlock the use of diamond for semiconductor applications, has been that of ‘surface transfer doping’ - a process by which intrinsically insulating diamond surfaces can be made semiconducting without the need for traditional impurity doping. Here, we present a review of progress in surface transfer doping of diamond, both a history and current outlook of this highly exploitable attribute.     

Static electrification of solid oxide in liquid metal and electrical double layer at the interface

Static electrification of a solid oxide, say a semiconducting oxide in liquid metal, is mainly due to electron transfer between two phases. Excess electrons in the liquid metal phase provided by the oxide give rise to an electrical double layer at the interface. The electrical double layer may be divided into three parts, an immobile inner layer, a compressed diffuse layer, and a flat layer extending into the bulk liquid metal. Differential potential analysis and the induced emf method were used to measure the potential of the compressed diffuse layer and the excess electron density of the flat layer, respectively. Results show that most oxides in liquid metals carry positive charges on their surfaces and the potentials of the compressed diffuse layer are in the range of 3 to 42 microV. Such a low potential implies that the diffuse layer is considerably compressed. The excess electron densities of the flat layer are on the order of 10(22) electrons/m(3) of Hg and their contributions to surface charges of oxide are in the range of 10(17) to 10(18) charges/m(2) for the oxide/mercury systems with a solid density of 0.3 wt% at room temperature.     

Rapid quantitative analysis of fayalite and silica formed during decarburization of electrical steel

Subscales on surfaces are affected by the temperature and oxidation potential during decarburization annealing of electrical steel containing 3 wt% silicon. Knowledge of the structural and chemical properties of the surface oxide layer subscales permits the control of high‐temperature oxidation processes in the electrical steel. In the present work, the oxide layers were characterized by transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectrometry, and glow discharge optical emission spectrometry (GD‐OES). The main oxide compounds formed within the subscales during decarburization annealing of the electrical steel were fayalite (Fe₂SiO₄) and silica (SiO₂). The fayalite and silica contents were quantitatively determined by wet analysis via the galvanostatic electrolysis method, and these oxide content measurements were compared with the fayalite content determined by FTIR spectrometry and the silica determined by GD‐OES. The results determined by rapid methods and wet analysis showed good agreement. The present findings show that FTIR spectrometry and GD‐OES measurements may be used for the rapid quantitative analysis of fayalite and silica in surface oxide layers during the manufacture of electrical steel. Copyright © 2011 John Wiley & Sons, Ltd.     

The diamond/aqueous electrolyte interface: an impedance investigation

We have investigated the electrochemical interface between diamond electrodes and aqueous electrolytes using electrochemical techniques such as cyclic voltammetry and ac impedance spectroscopy. High-quality CVD-grown boron-doped polycrystalline diamond electrodes and IIa single crystalline natural diamond electrodes have been used in this study. In the case of hydrogen-terminated diamond electrodes, the electrochemical interface is dominated by the electrochemical double layer. Frequency-dependent impedance spectroscopy reveals a potential regime in which the contribution of ion adsorption becomes relevant. We have conducted experiments to evaluate the effect of pH and ionic strength on the double layer. Our results suggest that only ions resulting from water auto-dissociation, i.e., hydroxide and hydronium ions, are responsible for ion adsorption and, thus, able to modify the charge at the double layer. In contrast, no effect of the adsorption of several dissolved ions (such as Na+, K+, Cl-) has been observed On the basis of the electrochemical characterization of H-terminated diamond surfaces, we also discuss the phenomenon of the surface conductivity in diamond, as well as the pH sensitivity of the diamond surface. The influence of the O2/OH- and H2/H3O+ redox couples on the origin of the surface conductivity is discussed.     

Approximate analytical expressions for the electrical potential between two planar, cylindrical, and spherical surfaces

Approximate analytical expressions for the electrical potential of planar, cylindrical, and spherical surfaces are derived for the case in which the dispersion medium contains counterions only. On the basis of the results for single surfaces, those for two identical surfaces can be derived. The curvature effect of a surface on the electrical potential distribution can be neglected when the order of its radius exceeds approximately 100 times the thickness of the corresponding double layer. If this effect needs to be considered, it can be taken into account by multiplying a correction function by the electrical potential of a planar surface. The electrical potential at the center between two derived surfaces is readily applicable to the evaluation of the electrostatic force per unit area between two surfaces, or the osmotic pressure. For the same set of parameters, the magnitudes of the osmotic pressure for various types of surfaces rank as follows: planar surface > cylindrical surfaces > spherical surfaces.     

Self-assembly to monolayer graphene film with high electrical conductivity

Monolayer chemically converted graphene (CCG) nanosheets can be homogeneously self-assembled onto silicon wafer modified by 3-aminopropyl triethoxysilane (APTES) to form very thin graphene film. The CCG film was characterized by FT-IR, XRD, SEM, TEM and AFM. Results show that CCG sheets formed monolayer film after assembled onto silicon wafer and there is a very tight chemical bond between sheets and wafer. Furthermore, the electrical measurements revealed that the monolayer graphene film has an excellent electrical conductivity.     

Photochemical functionalization of hydrogen-terminated diamond surfaces: a structural and mechanistic study

Hydrogen-terminated diamond surfaces can be covalently modified with molecules bearing a terminal vinyl (C=C) group via a photochemical process using sub-band-gap light at 254 nm. We have investigated the photochemical modification of hydrogen-terminated surfaces of nanocrystalline and single-crystal diamond (111) to help understand the structure of the films and the underlying mechanism of photochemical functionalization. A comparison of the rates of photochemical modification of single-crystal diamond and nanocrystalline diamond films shows no significant difference in reactivity, demonstrating that the modification process is not controlled by grain boundaries or other structures unique to polycrystalline films. We find that both single-crystal and polycrystalline hydrogen-terminated diamond samples exhibit negative electron affinity and are functionalized at comparable rates, while oxidized surfaces with positive electron affinity undergo no detectable reaction. Gas chromatography-mass spectrometry (GC-MS) analysis shows the formation of new chemical products in the liquid phase that are formed only when the alkenes are illuminated in direct contact with H-terminated diamond, while control experiments with other surfaces and in the dark show no reaction. Our results show that the functionalization is a surface-mediated photochemical reaction and suggest that modification is initiated by the photoejection of electrons from the diamond surfaces into the liquid phase.     

Covalently modified silicon and diamond surfaces: resistance to nonspecific protein adsorption and optimization for biosensing

We report the direct covalent functionalization of silicon and diamond surfaces with short ethylene glycol (EG) oligomers via photochemical reaction of the hydrogen-terminated surfaces with terminal vinyl groups of the oligomers, and the use of these monolayers to control protein binding at surfaces. Photochemical modification of Si(111) and polycrystalline diamond surfaces produces EG monolayers linked via Si-C bond formation (silicon) or C-C bond formation (diamond). X-ray photoelectron spectroscopy was used to characterize the monolayer composition. Measurements using fluorescently labeled proteins show that the EG-functionalized surfaces effectively resist nonspecific adsorption of proteins. Additionally, we demonstrate the use of mixed monolayers on silicon and diamond and apply these surfaces to control specific versus nonspecific binding to optimize a model protein sensing assay.     

Electrochemical properties of two dimensional assemblies of insulating diamond particles

The electrochemical properties of two-dimensional assemblies of 500 nm type Ib diamond particles are investigated as a function of their surface oxidation state. High Pressure High Temperature particles are sequentially exposed to a hot strong acid bath and to H(2) plasma in order to generate oxygen (ODP) and hydrogen surface terminations (HDP). Changes in the surface composition following the chemical treatments are confirmed by FTIR. Electrophoretic mobility measurements show that the diamond particles exhibit a negative surface charge at pH above 7 independently of the surface termination. Oxidation in the acid bath and subsequent reduction in the H(2) plasma only affects about 30% of the particle surface charge. The intrinsic negative charge allows the formation of 2D assemblies by electrostatic adsorption on poly(diallyldimethylammonium chloride) (PDADMAC) modified In-doped SnO(2) electrodes (ITO). The particle number density in the assembly was controlled by the adsorption time up to a maximum coverage of ca. 40%. Cyclic voltammetry in the absence of redox species in solution show that the acid treatment effectively removes responses associated with sp(2) carbon impurities, resulting in a potential independent capacitive signal. On the other hand, HDP assemblies are characterized by a charging process at a potential above 0.1 V vs Ag/AgCl. These responses are associated with hole-injection into the valence band edge which is shifted to approximately -4.75 eV vs vacuum upon hydrogenation. Information concerning the position of the valence band edge as well as hole number density at the HDP surface as a function of the applied potential are extracted from the electrochemical analysis.     

Covalent adlayer growth on a diamond thin film surface

The surface of boron-doped diamond thin films can be modified by exposure to a strong oxidizing agent, resulting in the formation of -OH and =O terminated diamond. The -OH groups are reacted with an acid chloride to produce a covalently bound, modified diamond thin film surface. The demonstration of these reactions allows for the facile modification of diamond surfaces using techniques well established for oxide surfaces. Characterization of the covalently bound species shows submonolayer coverage, and time-resolved fluorescence measurements are reflective of the highly featured nature of the diamond film.