ITO导电玻璃表面直接电沉积Au的机理

用循环伏安和电位阶跃法研究Au在氧化铟锡(ITO)透明导电膜玻璃表面的电沉积过程的初期阶段. 发现在ITO表面Au的电沉积经历成核过程以及受[AuCl₄]^-扩散控制的晶核生长过程. 通过改变扫描速率分析循环伏安曲线的变化, 当扫描速率较快时, 发现Au在ITO表面的沉积过程经历[AuCl₄]^-→[AuCl₂]^-→Au两步进行; 当扫描速率较慢时, 受歧化反应作用影响而只表现为一步沉积[AuCl₄]^-→Au. 通过电位阶跃实验, 验证了Au的两步沉积过程, 并求得[AuCl₄]^-的扩散系数为1.3×10^-5 cm²·s^-1. 将成核曲线与理论曲线对照, 得出Au在ITO表面的沉积符合瞬时成核理论. 通过场发射扫描电镜(FE-SEM)对Au核形貌进行分析, 根据扫描电镜图可以得到阶跃时间和阶跃电位对电沉积Au的形貌的影响.     

形貌可控的钯纳米粒子的电化学制备及电催化性质

以NaPdCl4为前驱体, 以柠檬酸钠为包裹剂, 通过两步恒电势法在氧化铟锡(ITO)导电玻璃基底上沉积得到不同形貌的钯纳米粒子(PdNPs). 通过调节晶种沉积电势和粒子生长电势、柠檬酸根和溴离子的浓度及反应温度等因素, 可以控制PdNPs的形貌、尺寸及在ITO基底上的生长密度; 制备出了钯纳米锥阵列及球形、花状和多面体形的PdNPs. 研究结果表明, 钯纳米锥阵列与其它形状的PdNPs相比, 在单位面积ITO基底上具有更大的表面积, 表现出对甲醇更强的电化学氧化能力.     

纯钯电沉积及其成核机理研究

研究在柠檬酸钾和草酸铵镀液体系中纯钯电沉积及电结晶机理。结果表明，采用本实验案研制的添加剂（２）ＸＰ－４和ＸＰ－７，可在电流密度０．５￣３．５Ａ／ｄｍ＾２，温度４０￣６０℃的宽广范围内获得全光亮的钯电沉积积层。采用脉冲电源电镀可有效地改善厚沉积层质量，减少沉积层裂纹和孔洞，循环伏安实验表明，钯电极过程的阴阳峰电位之差达１．０５Ｖ，说明其电极过程明显不可逆；伏安图上同时出现－感抗性电流环，说明钯沉积     

纳米Pd上H2O2的电催化还原反应

利用纳米Pd颗粒修饰的Au旋转圆盘电极, 通过强制对流条件下的线性电势扫描伏安法, 研究了酸性介质中H2O2在纳米Pd催化剂上的电还原反应. 动力学研究结果表明, H2O2在纳米Pd上电还原反应的表观活化能为27.6 kJ·mol-1, 反应为2电子转移过程, 电解质的阴离子类型显著影响纳米Pd对H2O2电化学还原反应的催化性能. 根据动力学电流与H2O2浓度及与H+浓度的关系, 提出了Pd催化H2O2电还原反应可能的速率控制步骤, 并讨论了其可能的反应机理.     

Pd/PEI-GNs复合材料的制备及对对硝基苯酚的电催化还原性能

以聚乙烯亚胺(PEI)功能化的石墨烯(PEI-GNs)为载体, 利用电化学还原法制备了Pd/PEI-GNs复合物. 采用红外光谱仪、 X射线光电子能谱仪、 X射线粉末衍射仪和扫描电子显微镜等对复合物的组成、 结构和形态进行了表征. 结果表明, Pd/PEI-GNs复合物中Pd颗粒均匀分散在PEI-GNs基底上. 采用循环伏安法、 交流阻抗法和计时电流法等电化学方法研究了Pd/PEI-GNs复合物的电化学性能. 结果表明, 制备的复合物催化剂对对硝基苯酚还原具有较好的催化活性和稳定性, 这主要是由于Pd纳米颗粒在PEI-GNs载体上均匀分散以及PEI-GNs优异的电子传递能力.     

电沉积二氧化锰成核机理及其充放电性能

采用计时电流法沉积纳米MnO₂电极材料,利用Scharifker-Hills成核理论模型分析时间-电流(i-t)曲线判断了MnO₂成核机理。 对3种不同的成核方式制得的MnO₂材料进行电化学超级电容性能测试、用SEM观察了其微观形貌。 比较了不同沉积方法对沉积材料结构、电容性能的影响。 计时电流测试发现,在0.1 mol/L Mn²⁺溶液中,电势阶跃至0.365 V,初始成核符合瞬时成核机理,在0.01 mol/L Mn²⁺溶液中,电势阶跃至0.418 V,初始成核存在瞬时成核和连续成核两种不同机理,在0.5 mmol/L Mn²⁺溶液中,电势阶跃至0.515 V,初始成核则符合连续成核机理。 超级电容性能测试发现,瞬时成核下制得的MnO₂电极材料相对于另外两种成核方式得到的电极材料具有更好的电容性能,这是因为瞬时成核更易于形成多孔、纳米片(棒)状等高比表面积的沉积物,表明制备方法影响MnO₂电极材料电容性能。     

脉冲电沉积钯镍合金纳米颗粒及其甲酸电催化氧化

采用方波脉冲方法,在钯镍合金电解液中成功地电化学沉积出镍原子含量分别为12.0%、16.4%和22.6%的钯镍合金纳米颗粒.钯镍合金纳米颗粒为球状,粒径50~80 nm.随钯镍合金生长电位负移,合金的镍含量提高,其纳米颗粒大小基本相似但纳米颗粒数目增多,交联度提高和真实活性面积增大.钯镍合金纳米颗粒镍含量提高,在硫酸溶液中其氢弱吸附峰电流增大.钯镍合金纳米颗粒电极的甲酸电催化氧化活性较好,随合金纳米颗粒的镍含量提高和交联度增加,合金纳米颗粒电极的甲酸电催化氧化稳定性更高.     

脉冲电沉积Pd-Ni合金纳米颗粒及其甲酸电催化氧化

采用方波脉冲方法,在钯镍合金电解液中成功地电化学沉积出镍原子含量分别为12.0%、16.4%和22.6%的钯镍合金纳米颗粒. 钯镍合金纳米颗粒为球状,粒径50 ~ 80 nm. 随钯镍合金生长电位负移,合金的镍含量提高,其纳米颗粒大小基本相似但纳米颗粒数目增多,交联度提高和真实活性面积增大. 钯镍合金纳米颗粒镍含量提高,在硫酸溶液中其氢弱吸附峰电流增大. 钯镍合金纳米颗粒电极的甲酸电催化氧化活性较好,随合金纳米颗粒的镍含量提高和交联度增加,合金纳米颗粒电极的甲酸电催化氧化稳定性更高.     

电沉积制备的PtNi纳米粒子用于氧还原反应:成核和生长机理

质子交换膜燃料电池(PEMFCs)电堆中阴极Pt基催化剂的高用量造成其成本居高不下,成为阻碍燃料电池汽车商业化推进的重要原因,因此开发低Pt、高活性的Pt基催化剂势在必行.Pt合金催化剂能够有效地降低Pt用量,并通过对合金颗粒的元素比例、晶面、粒径等实行精确调控,显著提升氧还原(ORR)催化活性.然而,目前常用的制备方法由于原料与制备成本高昂、过程复杂大都难以适应规模化生产需求.电化学方法通过控制施加的电流或电位控制晶体生长.在水体系中该方法已得到验证,但由于Pt化合物的热力学标准电极电位与过渡金属元素之间相差较大,且对于过渡金属来说,电负性大多小于铂,因此还原电位通常负于析氢电位,使得二者难以实现共沉积.有机体系中电位窗口比水体系大得多,Pt与电位较负的过渡金属可实现共沉积,采用小分子有机溶剂也可避免溶剂清洗问题,具有应用潜力.本文提出了一种简单的一步电沉积方法,选择易溶于水的N,N-二甲基甲酰胺(DMF)作为溶剂,将碳载体滴涂到玻碳电极上作为工作电极,通过电化学方法直接将Pt-Ni合金沉积到碳载体上,并利用物化表征与密度泛函理论(DFT)理论计算来探究共沉积机理.透射电镜表征结果表明,在不同的沉积电位下均可得到分散均匀、粒径适当的催化剂;且随着电位值降低,催化剂颗粒分散得更均匀,颗粒粒径不断减小.元素分布和晶面结果表明,铂镍元素均匀分布于颗粒中.所有样品均表现出优异的ORR性能,最高的面积比活性达到商业催化剂的6.85倍.将材料表征、电化学表征与DFT计算结合,建立起了铂镍合金生长过程的模型,并发现了有机体系中独特的成核-生长机理.将体系中的DMF换成超纯水,用同样的方法进行沉积,得到的催化剂颗粒团聚严重,说明DMF的使用能够避免颗粒团聚.在单独铂的体系中沉积发现,负载量极小,表明体系中镍前驱体的添加对于催化剂的沉积过程起到重要作用.电化学表征结果表明,在所选用的DMF有机体系中,镍的还原电位与铂的十分接近,但还原动力学更慢,趋向于先形成吸附原子后快速还原.由此可以推测,在二者合金的形成过程中,镍在碳载体表面的缓慢还原而形成的吸附原子能够成为铂还原的活性位点,从而降低了铂还原成核所需的能量,使得载体上的成核位点大大增加,这与DFT模拟结果一致.DFT建立了碳上镍的位点和铂的位点,分别在上面进行铂的还原,发现镍位点上比铂位点上更容易实现铂沉积.本文提出了铂镍共沉积的机理:在过电位(即还原能量)下,铂的还原动力学较镍稍快,于是铂先还原形成晶核,但难以达到生长的临界半径,于是单独铂体系中的沉积负载量很少.载体上还原的镍为铂还原提供了大量的活性位点,促进了铂还原,并与镍共沉积.Pt-Ni表面则进一步促进了铂的沉积和颗粒的生长.综上,本文提出了一种用于制备铂合金催化剂的有机电沉积体系,实现了单分散的碳载铂镍合金催化剂的一步制备.随后,本文将材料表征、电化学表征与DFT计算相结合,建立起了有机体系中铂镍合金成核-生长过程的机理模型.     

电沉积制备的PtNi纳米粒子用于氧还原反应:成核和生长机理

质子交换膜燃料电池(PEMFCs)电堆中阴极Pt基催化剂的高用量造成其成本居高不下,成为阻碍燃料电池汽车商业化推进的重要原因,因此开发低Pt、高活性的Pt基催化剂势在必行.Pt合金催化剂能够有效地降低Pt用量,并通过对合金颗粒的元素比例、晶面、粒径等实行精确调控,显著提升氧还原(ORR)催化活性.然而,目前常用的制备方法由于原料与制备成本高昂、过程复杂大都难以适应规模化生产需求.电化学方法通过控制施加的电流或电位控制晶体生长.在水体系中该方法已得到验证,但由于Pt化合物的热力学标准电极电位与过渡金属元素之间相差较大,且对于过渡金属来说,电负性大多小于铂,因此还原电位通常负于析氢电位,使得二者难以实现共沉积.有机体系中电位窗口比水体系大得多,Pt与电位较负的过渡金属可实现共沉积,采用小分子有机溶剂也可避免溶剂清洗问题,具有应用潜力.本文提出了一种简单的一步电沉积方法,选择易溶于水的N,N-二甲基甲酰胺(DMF)作为溶剂,将碳载体滴涂到玻碳电极上作为工作电极,通过电化学方法直接将Pt-Ni合金沉积到碳载体上,并利用物化表征与密度泛函理论(DFT)理论计算来探究共沉积机理.透射电镜表征结果表明,在不同的沉积电位下均可得到分散均匀、粒径适当的催化剂;且随着电位值降低,催化剂颗粒分散得更均匀,颗粒粒径不断减小.元素分布和晶面结果表明,铂镍元素均匀分布于颗粒中.所有样品均表现出优异的ORR性能,最高的面积比活性达到商业催化剂的6.85倍.将材料表征、电化学表征与DFT计算结合,建立起了铂镍合金生长过程的模型,并发现了有机体系中独特的成核-生长机理.将体系中的DMF换成超纯水,用同样的方法进行沉积,得到的催化剂颗粒团聚严重,说明DMF的使用能够避免颗粒团聚.在单独铂的体系中沉积发现,负载量极小,表明体系中镍前驱体的添加对于催化剂的沉积过程起到重要作用.电化学表征结果表明,在所选用的DMF有机体系中,镍的还原电位与铂的十分接近,但还原动力学更慢,趋向于先形成吸附原子后快速还原.由此可以推测,在二者合金的形成过程中,镍在碳载体表面的缓慢还原而形成的吸附原子能够成为铂还原的活性位点,从而降低了铂还原成核所需的能量,使得载体上的成核位点大大增加,这与DFT模拟结果一致.DFT建立了碳上镍的位点和铂的位点,分别在上面进行铂的还原,发现镍位点上比铂位点上更容易实现铂沉积.本文提出了铂镍共沉积的机理:在过电位(即还原能量)下,铂的还原动力学较镍稍快,于是铂先还原形成晶核,但难以达到生长的临界半径,于是单独铂体系中的沉积负载量很少.载体上还原的镍为铂还原提供了大量的活性位点,促进了铂还原,并与镍共沉积.Pt-Ni表面则进一步促进了铂的沉积和颗粒的生长.综上,本文提出了一种用于制备铂合金催化剂的有机电沉积体系,实现了单分散的碳载铂镍合金催化剂的一步制备.随后,本文将材料表征、电化学表征与DFT计算相结合,建立起了有机体系中铂镍合金成核-生长过程的机理模型.     

Electrocatalysis of Horseradish Peroxidase Immobilized on Cobalt Nanoparticles Modified ITO Electrode

Abstract

It is the first time that Horseradish peroxidase (HRP) was successively immobilized on the magnetic cobalt nanoparticles modified ITO (indium tin oxide) electrode. Morphologies of electrode surface were featured by the field emission‐scanning electron microscope (FSEM). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to characterize the modified process of electrode. Direct electrochemistry and electrocatalysis of HRP immobilized on nano‐Co/ITO were investigated. The biosensor exhibited high sensitivity, good stability, and excellent electrocatalytic activity to the reduction of H₂O₂. Under the optimized experimental conditions, a calibration curve over 2.0×10^?9～2.0×10^?8 mol l^?1 and 2.0×10^?7～2.0×10^?6 mol l^?1, with a limit of detection of 1.9×10^?9 mol l^?1 was obtained. The apparent Michaelis‐Menten constant (K _M ^app ) for HRP/nano‐Co/ITO electrode was calculated to be 0.79 mmol l^?1, indicating a higher affinity of HRP attached on the modified electrode.     

Preparation of a Novel NH2 + Ion Implantation Modified Electrode and Its Study of the Electrochemical Behavior of Hemoglobin

Abstract

A novel functional electrode was obtained by implanting NH₂ ⁺ into ITO film (NH₂/ITO) for the first time. The NH₂/ITO surface showed a better affinity to gold nanoparticles than bare ITO. Gold nanoparticles were deposited on the surface of NH₂/ITO electrode (Au/NH₂/ITO). The Au/NH₂/ITO and NH₂/ITO electrodes were used to observe the electrochemical behavior of Hemoglobin (Hb) immobilized on the electrodes surfaces. The peak current value of Hb immobilized on NH₂/ITO increased compared with on bare ITO while peak current value of Hb immobilized on Au/NH₂/ITO increased compared with on Au/ITO. Linkage between the ‐NH₂ implanted into the ITO film and the ‐COOH of Hb was thought to be the reason for the increase of active Hb coverage on NH₂/ITO compared with bare ITO. Increase of active Hb coverage on Au/NH₂/ITO compare with Au/ITO was attributed to the different amount of gold nanoparticles deposited. Results showed the novel NH₂/ITO and Au/NH₂/ITO electrodes exhibited good stability, reproducibility besides selectivity and sensitivity. The electrode process of Hb immobilized on Au/NH₂/ITO was quasi‐reversible with adsorption. The electrode reaction rate constant k_s and other related constants were determined. X‐ray photoelectron spectroscopy (XPS), field‐emission scanning electron microscopy (FE‐SEM), and impedance spectra were used to characterize the different surfaces.     

Determination of hemoglobin at a novel NH2/ITO ion implantation modified electrode

A novel electrode was prepared by implanting NH₂ ⁺ into an ITO film (NH₂/ITO). Gold nanoparticles were deposited on the surface of NH₂/ITO electrode. The NH₂/ITO and Au/NH₂/ITO electrodes were used to determine hemoglobin (Hb) immobilized on the electrodes surfaces. The relationship of the reductive peak current value of Hb among different electrodes was: Hb/ITO:Hb/Au/ITO:Hb/NH₂/ITO:Hb/Au/NH₂/ITO=1:1.5:2:4. The linkage between the –NH₂ implanted into ITO film and the –COOH of Hb was recognized to be the reason for the increase of active Hb coverage on NH₂/ITO electrode compared with the ITO electrode. Increase of active Hb coverage on Au/NH₂/ITO compared with Au/ITO was attributed to the different amount of gold nanoparticles deposited. The determination of Hb at an Au/NH₂/ITO electrode was optimized. Calibration curve was obtained over the range of 1.0 × 10⁻⁸ – 1.0 × 10⁻⁶ mol · L⁻¹ with a detection limit of 1.0 × 10⁻⁸ mol · L⁻¹. Results showed that the novel NH₂/ITO and Au/NH₂/ITO electrodes exhibited good stability, reproducibility besides better electrochemical performance. Correspondence: Jing Bo Hu, Department of Chemistry, Beijing Normal University, Beijing 100875, China     

钯纳米粒子在电极表面的制备及其对氧的催化还原

纳米微粒的体积效应使其成为表面纳米工程及功能化纳米结构材料制备的理想研究对象 [1～ 3] .纳米粒子具有独特的电子、催化及光学特性[4 ] ,近年来关于纳米粒子的制备及其在材料科学领域中的应用受到研究者的极大关注 .而贵金属纳米粒子由于其在催化领域中的广泛应用而成为最重要的研究对象之一[5,6 ] .电催化氧还原是一直为化学家瞩目的研究领域[7～ 9] .研究主要目的之一是寻找合适的氧电极反应催化剂 ,并使之能够应用于燃料电池中 .其中催化氧电极材料研究得最多的是贵金属 Pt[10 ,11] .贵金属 Pd对氧催化还原的研究工作很少 .我们首次…     

芦丁在铂纳米/碳纳米管修饰电极上电化学行为研究

通过电沉积的方式在多壁碳纳米管(MWCNTs)修饰玻碳电极表面上沉积铂(pt)纳米粒子,并运用循环伏安法(CV)、示差脉冲伏安法(DPV)探讨了芦丁在铂纳米/碳纳米管/玻碳电极上的电化学行为.实验结果表明,芦丁在该修饰电极上呈现一对良好氧化还原峰,其氧化峰电流与浓度在3.2×10(-8)～1.2×10(-5)mol/L...     

Electrochemical Behavior and Its Electrocatalytic Activity of A P—Mo Heteropolyanion Modified ITO Electrode

ITO is a versatile material in the electronic industry because of its special transparent and conductive properties. However, there are a few reports regarding the adsorption of organic or organometallic compounds on the ITO surface1-4. The heteropolyanions are interested in the field of material science, catalytics, biology, and medicine owing to their chemical, structural, and electronic versatility5-7. One of the most important properties of polyoxometalate anions is their ability to a…     

Disposable Amperometric A-fetoprotein Immunosensor Based on the Biocompatible Silk Protein Membranes-Modified Indium Tin Oxide Electrodes

A simple and disposable electrochemical immunosensor for detection of 68 kDa alpha-fetoprotein (AFP) was fabricated based on films of silk fibroin protein membrane (SFPM)/Prussian blue (PB)/deposition of gold nanoparticles (DpAu). First, DpAu and PB were electrochemically deposited successively on the surface of indium tin oxide (ITO) electrode. Then, SFPM with excellent biocompatibility was modified on the surface of PB/DpAu/ITO. The SFPM could form a stable matrix on the electrode surface for the deposition of immunoactive agents. More importantly, the SFPM could prevent the possible leakage of electron mediator and enhance the stability of immunosensor. Scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were used to characterize the assembly process of the modified electrode. The linear range of the proposed immunosensor extended from 1.0 to 200.0 ng/mL for detection of AFP with a detection limit of 0.6 ng/mL. Moreover, the CV test demonstrated the immunosensor exhibited acceptable reproducibility and stability. This composite membrane could be applied for the detection of different biomarkers, diagnosis, and monitoring of carcinoma.

[Supplementary materials are available for this article. Go to the publisher's online edition of Analytical Letters for the following free supplemental resources: additional figures.]     

Immobilization of Hemoglobin on Cobalt Nanoparticles-modified Indium Tin Oxide Electrode:Direct Electrochemistry and Electrocatalytic Activity

A cobalt nanoparticles-attached indium tin oxide(CoNPs/ITO) electrode was applied to the immobilization of hemoglobin(Hb) and an Hb modified CoNPs/ITO electrode(Hb/CoNPs/ITO) was prepared. The direct electron transfer of Hb was shown by the well-behaved voltammetric responses for Hb/CoNPs/ITO electrode and the effects of scan rate and pH value were observed. Based on the catalytic activity of Hb immobilized on the CoNPs/ITO electrode toward the reduction of H₂O₂, a mediator-free H₂O₂ sensor was developed. A linear relationship existed between the catalytic current and the H₂O₂ concentration in a range of 1.0―100.0 μmol/L with a detection limit (S/N=3) of 0.2 μmol/L.     

钛基二氧化铅电极电沉积制备过程中的立体生长机理

采用恒电位的方法在涂有SnO2＋Sb2O5中间层的Ti基体上电沉积制备了不同颗粒尺度的Ti/PbO2电极, 利用XPS, XRD和SEM等方法对Ti/PbO2电极电沉积制备过程中电极的结构、表面形貌等物理化学性能进行了研究. 结果表明, Ti/PbO2电极涂层中Pb元素在138.2～138.4 eV之间有明显的Pb4f7/2峰, 表明电极表面上主要得到的是PbO, XRD和XPS分析结果证明电极涂层体相生成的是PbO2. 基于Ti/PbO2涂层的形成是不同晶面生长过程的事实, 提出Ti/PbO2电极的立体生长机理.