Correlation between supercooled liquid region and crystallization behavior with alloy composition of La-Al-Cu metallic glasses

Bulk metallic glasses (BMGs) with large supercooled liquid region are promising materials for superplastic forming. In this paper, we demonstrate a microstructure-based strategy to pinpoint the composition with the largest supercooled liquid region in La 86 x Al 14 Cu x (x=16 at%-20 at%) metallic glass system. By monitoring the changes in crystallization behavior of the glassy alloys with composition to search for the alloys exhibiting eutectic crystallization, the glassy alloys with the largest supercooled...     

Compressive fracture characteristics of Zr-based bulk metallic glass

The compressive fracture characteristics of Zr-based bulk metallic glass under uniaxial compression tests are studied.The zigzag rheological behavior is observed in the compression stress-strain curves of amorphous alloys.At room temperature the uniaxial compression fracture takes place along the plane which is at a 45-degree angle to the direction of the compressive stress.The microstructure of a typical fracture pattern is the vein network.A unique,finger-like vein pattern is found to exist at the fractur...     

退火态Zr55A110Ni5Cu30块体非晶合金在轧制过程中的自由体积演化

将Zr55All0Ni5Cu30块体非晶合金在715K等温退火30min，引入少量纳米晶，然后于室温以不同的应变速率进行轧制，用差示扫描量热仪考察不同应变量样品的热稳定性和自由体积演化．结果表明：即使轧制到95％的最大应变量，样品的热稳定性也几乎没有发生改变．在各种应变速率下，随着应变量的增加，自由体积含量持续上升．但随着应变速率的增加，相同应变量下自由体积的含量先上升后降低，该规律与单一非晶态结构合金在塑性变形过程中自由体积的变化情况截然不同．     

Deformation behavior of Fe-based bulk metallic glass during nanoindentation

Fe-based bulk metallic glasses (BMGs) normally exhibit super high strength but significant brittleness at ambient temperature. Therefore, it is difficult to investigate the plastic deformation behavior and mechanism in these alloys through conventional tensile and compressive tests due to lack of distinct macroscopic plastic strain. In this work, the deformation behavior of Fe₅₂Cr₁₅Mo₉Er₃C₁₅B₆ BMG was investigated through instrumented nanoindentation and uniaxial compressive tests. The results show that serrated flow, the typical plastic deformation feature of BMGs, could not be found in as-cast and partially crystallized samples during nanoindentation. In addition, the deformation behavior and mechanical properties of the alloy are insensitive to the applied loading rate. The mechanism for the appearance of the peculiar deformation behavior in the Fe-based BMG is discussed in terms of the temporal and spatial characteristics of shear banding during nanoindentation. Supported by the National Natural Science Foundation of China (Grant Nos 50571109, 10572142 and 56771102) and the National Basic Research Program of China (973 Program)(Grant No 2007CB613900)     

Formation and magnetic properties of Co–Fe-based bulk metallic glasses with supercooled liquid region

A new Co–Fe-based ferromagnetic bulk metallic glass (BMG) was synthesized by copper mould casting method. The thermal stability and crystallization processes were investigated by differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The soft magnetic behavior was studied by DC magnetic measurements. The high glass formation ability was interpreted in terms of the effective suppression of nucleation and growth of the intermetallic compounds which appear in the multicomponent system during solidification. The high thermal stability indicates that the new Co–Fe-based BMG could be used as high-temperature magnetic material. The low coercivity which was as low as 8 A/m for the as-cast sample was found in the Co–Fe-based metallic glass cylinder with a diameter of 1.5 mm.     

退火态Zr55Al10Ni5Cu30块体非晶合金在轧制过程中的自由体积演化

将Zr₅₅Al₁₀Ni₅Cu₃₀块体非晶合金在715 K等温退火30 min, 引入少量纳米晶, 然后于室温以不同的应变速率进行轧制, 用差示扫描量热仪考察不同应变量样品的热稳定性和自由体积演化. 结果表明:即使轧制到95%的最大应变量, 样品的热稳定性也几乎没有发生改变. 在各种应变速率下, 随着应变量的增加, 自由体积含量持续上升. 但随着应变速率的增加, 相同应变量下自由体积的含量先上升后降低, 该规律与单一非晶态结构合金在塑性变形过程中自由体积的变化情况截然不同.     

Pd-Si binary bulk metallic glass

Pd_80+x Si_20−x (x = 0, 1, and 2) binary metallic glasses with the diameter ranging from 7 to 8 mm were prepared by a combination of fluxing and water quenching or air cooling. Thermal analysis results show that with increasing Si content, the glass transition temperature T _g, the initial crystallization temperature T _x and the onset crystallization temperature T _p of Pd-Si binary glassy alloys increase. Moreover, the supercooled liquid region reaches 61 K. It indicates that Pd-Si binary alloys possess large glass forming ability, which can be greatly improved by fluxing treatment. Supported by the National Basic Research Program of China (Grant No. 2007CB613905) and the National Natural Science Foundation of China (Grant Nos. 50671050 and 50431030)     

Thermodynamical properties of Zr-based bulk metallic glasses

The temperature dependence of Gibb's free energy difference (ΔG), entropy difference (ΔS) and enthalpy difference (ΔH) between the undercooled melt and the corresponding equilibrium solid phases of bulk metallic glass (BMG) forming melts has been proved to be very useful in the study of their thermodynamical behavior. The present study is made by calculating ΔG, ΔS and ΔH in the entire temperature range T_m (melting temperature) to T_g (glass transition temperature) for three Zr-based samples of BMGs: Zr₅₇Cu_15.4Ni_12.6Al₁₀Nb₅, Zr_41.2Ti_13.8Ni₁₀Cu_12.5Be_22.5 and Zr_58.5Cu_15.6Ni_12.8Al_10.3Nb_2.8. The study is made on the basis of Taylor's series expansion and a comparative study is also performed between the present result and the result obtained in the framework of expansions proposed by earlier workers, and also with the experimental results. An attempt has also been made to study the glass forming ability for BMGs.     

Zr-based bulk metallic glass as a cylinder material for high pressure apparatuses

Zirconium-based bulk metallic glass (Zr-based BMG) has outstanding properties as a cylinder material for piston-cylinder high pressure apparatuses and is especially useful for neutron scattering. The piston-cylinder consisting of a Zr-based BMG cylinder with outer/inner diameters of 8.8/2.5?mm sustains pressures up to 1.81?GPa and ruptured at 2.0?GPa, with pressure values determined by the superconducting temperature of lead. The neutron attenuation of Zr-based BMG is similar to that of TiZr null-scattering alloy and more transparent than that of CuBe alloy. No contamination of sharp Bragg reflections is observed in the neutron diffraction pattern for Zr-based BMG. The magnetic susceptibility of Zr-based BMG is similar to that of CuBe alloy; this leads to a potential application for measurements of magnetic properties under pressure.     

Energy model for the Zr-based metallic glass alloy melt with clusters

An energy model for the melt of bulk metallic glass (BMG) with clusters was established, the Gibbs free energy and interfacial energy for the Zr-Al-Ni ternary alloy melt with Zr2Ni clusters were calculated, and the effects of the clusters on the Gibbs free energy, interfacial energy and nucleation rate were analyzed. The results showed that the existence of the clusters in the Zr-Al-Ni ternary alloy melt enables the Gibbs free energy to decrease in the composition range where bulk metallic glass forms easily, makes the interfacial energy increase and changes the distribution of the interfacial energy with the alloy composition. Because of the clusters in the melt, the Gibbs free energy of the Zr66Al8Ni26 alloy melt decreases about 0.3-1 kJ/mol and the interfacial energy between the melt and crystal nucleus increases about 0.016 J/m2. The nucleation rate of the undercooled Zr66Al8Ni26 alloy melt decreases evidently under the influence of the clusters on Gibbs free energy and the interfacial energy, and the maximum of the nucleation rate in the melt with the Zr2Ni clusters is only about 107 mol-1·s-1.     

Effect of the cooling rate on plastic deformability of a Zr-based bulk metallic glass

The present work found the plastic deformability of Zr65Cu17.5Ni10Al7.5 BMG dependent on the cooling rate during the formation from the molten state alloy. The deformation behavior in the compression test of φ 2 mm Zr65Cu17.5Ni10Al7.5 BMGs as-cast or lathed from different sizes as-cast samples was characterized, and they exhibited different plastic strains. The compressive plastic strain increases with the decreasing diameter of the as-cast specimens, i.e. with increasing the cooling rate. It is suggested that free volume content in the BMGs, which is related to the cooling rate during the rapid solidification, could play an important role in the deformation process of the BMGs.     

Influence of free volume and medium-range order on the deformation response of rapidly solidified and bulk Zr-based (Zr52Ti6Al10Cu18Ni14) metallic glass

Free volume and medium-range order (MRO) present in rapidly solidified ribbons (RSRs) and bulk metallic glasses (BMGs) of Zr₅₂Ti₆Al₁₀Cu₁₈Ni₁₄ have been probed by high resolution electron microscopy, fluctuation microscopy, positron annihilation and differential scanning calorimetry. In the as-solidified condition, RSRs showed higher free volume and lower MRO in comparison to BMGs. Within BMGs, the central regions showed higher MRO and lower free volume than the peripheral regions. Uniform deformation of BMGs and RSRs modified their structures, where in, free volume increased in the former and reduced in the latter. These changes in structures led to work hardening in RSRs and work softening in BMGs. Such behaviour could be explained by invoking a concept of critical free volume in the glass phase. For samples (in as-solidified condition) having free volume higher than the critical value, free volume decreased with deformation and showed work-hardening behaviour. In contrast, the work softening behaviour was noticed in samples having free volume lower than the critical free volume.     

金属玻璃的热塑性成型

金属玻璃在其过冷液相区内表现出随着温度升高黏度逐渐降低的特性,因此可以对其进行热塑性加工.该性质颠覆了传统金属的加工成型方式,使得其在远低于传统金属材料加工的温度和应力作用下可以按照人们的要求进行成型.因此,一些具有低玻璃转变温度的金属玻璃又被称作金属塑料.另外,由于金属玻璃是一种无序结构材料,不存在位错、晶界等晶体缺陷,且热膨胀系数小,在热塑性成型中具有优异的尺寸精度,因此被认为是理想的微成型材料,有广阔的应用前景.本文系统介绍了金属玻璃的热塑性成型性质及其应用,从热塑性成型的基本概念出发,阐述了金属玻璃热塑性成型能力的评估指标、热塑性成型技术、热塑性微成型及其理论、热塑性微成型的应用等,对认识金属玻璃的热塑性及扩展其应用有重要的意义.     

大块金属玻璃Zr41Ti14Cu12.5Ni10Be22.5的流变行为研究

采用静态拉伸方法在连续升温条件下动态地测量了大块金属玻璃Zr41Ti14Cu12.5Ni10Be22.5（Vit1）的黏度随温度的变化关系.在应变速率与温度的关系曲线中，观测到了与玻璃转变和晶化过程相联系的多个应变速率峰.在玻璃转变温度Tg以上，大块金属玻璃Zr41Ti14Cu12.5Ni10Be22.5的过冷液体呈现Newton流体特征，其黏度与温度的关系符合Vogel Fulcher-Tammann (VFT)关系式，拟合得到脆度D*＝36，VFT温度T0＝319K，脆度参数m＝30，这说明Zr41T 关键词： 大块金属玻璃 应变速率 剪切黏度 自由体积     

Tribological characterisation of Zr-based bulk metallic glass in simulated physiological media

Due to their excellent wear resistant properties and high strength, as well as a low Young's modulus, Zr-based bulk metallic glasses (BMGs) are potentially suitable biomaterials for low-friction arthroplasty. The wear characteristics of the Zr_60.14Cu_22.31Fe_4.85Al_9.7Ag₃ bulk amorphous alloy against ultra-high-molecular-weight polyethylene (UHMWPE) compared to a CoCrMo/UHMWPE combination were investigated in two different wear screening test devices, reciprocating and unidirectional. Hank's solution and sterile calf bovine serum were selected as the lubricant fluid media. It was found that different fluid media had insignificant effect on polyethylene wear against BMG counterfaces. The wear behaviour obtained on both test devices demonstrated that Zr-based BMG achieved UHMWPE counterface wear rates superior to conventional cast CoCrMo alloy, where the wear rate of UHMWPE is decreased by over 20 times. The tribological performance of these joints is superior to that of conventional metal-on-polymer designs. Contact angle measurements suggested that the advantage of BMG over a CoCrMo alloy counterface is attributed to its highly hydrophilic surfaces.     

新型Pr基大块非晶及其特性研究

用铜模吸铸法获得了直径为5mm的一种新的Pr基大块非晶.与以往其他稀土-过渡金属(RE-TM)大块非晶不同的是，这种新的Pr基大块非晶具有明显的玻璃转变和稳定的过冷液相区，且其玻璃转变温度在目前已知的大块非晶中是最低的，T_g=409K.研究了该大块非晶的玻璃转变动力学，并给出了Kauzmann温度T_k、Vogel-Fulcher温度T⁰_g及脆性参数m等重要参数. 关键词： 大块非晶 玻璃转变 脆性参数m     

Atomic-scale structural evolution and stability of supercooled liquid of a Zr-based bulk metallic glass

In this Letter, direct experimental evidence is provided for understanding the thermal stability with respect to crystallization in the Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) glass-forming liquid. Through high-resolution transmission electron microscopy, the atomic-structure evolution in the glass-forming liquid during the isothermal annealing process is clearly revealed. In contrast with the existing theoretical models, our results reveal that, prior to nanocrystallization, there exists a metastable state prone to forming icosahedralike atomic clusters, which impede the subsequent crystallization and hence stabilize the supercooled liquid. The outcome of the current research underpins the topological origin for the excellent thermal stability displayed by the Zr-based bulk metallic glass.     

高压下Co在Zr46．75Ti8．25Cu7．5Ni10Be27．5大块金属玻璃过冷液相区中的扩散

通过离子注入结合二次离子质谱分析方法 ,研究了高压下Co在Zr4 6 .75Ti8.2 5Cu7.5Ni1 0 Be2 7.5大块金属玻璃过冷液相区中的扩散行为 .在 6 0 3K时 ,Co在Zr4 6 .75Ti8.2 5Cu7.5Ni1 0 Be2 7.5大块金属玻璃中的扩散系数随压力的增大而增大 ,其扩散激活体积ΔV =- 1.2 36Ω ,Ω是合金的平均原子体积 .结果表明 ,在热平衡状态下Co在Zr4 6 .75Ti8.2 5Cu7.5Ni1 0Be2 7.5大块金属玻璃中的扩散是通过间隙机理进行的     

Fracture characteristics of bulk metallic glass under high speed impact

High speed impact experiments of rectangular plate-shaped Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG) were performed using a two-stage light gas gun. Under spherical shock waves with impact velocities ranging from 0.503 km/s to 4.917 km/s, obvious traces of laminated spallation at the back (free) surface and melting (liquid droplets) at the impact point were observed. The angles about 0?, 17?, 36?, and 90? to the shocking direction were shown in the internal samples because of the interaction between the compressive shock waves and the rarefaction waves. The compressive normal stress was found to induce the consequent temperature rise in the core of the shear band.     

Corrosion behavior of bulk metallic glasses in different aqueous solutions

The corrosion behavior of as-cast fully amorphous, structural relaxed amorphous and crystallized Fe65.5Cr4Mo4Ga4P12C5B5.5 bulk metallic glasses (BMGs) in NaCl, HCl and NaOH solutions was investigated by electrochemical polarization and immersion methods. X-ray photoelectron spectroscopy measurements was used to analyze the changes of the elements on the alloy surface before and after immersion in various solutions. The corrosion resistance of the Fe65.5Cr4Mo4Ga4P12C5B5.5 BMG was better than its structural r...