磺酸型树脂固定床连续催化二壬基酚烷基转移反应的研究

以壬基酚装置精馏塔釜底液为原料,以磺酸型聚苯乙烯阳离子交换树脂为催化剂,采用常压固定床连续工艺,开展二壬基酚与苯酚的烷基转移反应研究制取壬基酚。分别采用红外光谱、差热热重分析、催化剂颗粒强度测试等表征方法对催化剂的组成、热稳定性及力学性能进行研究。考察了反应温度、原料配比、质量空速和反应时间等因素对催化性能的影响。结果表明,所制备的树脂具有良好的热稳定性和耐压强度,适用于180℃以下的固定床连续反应工艺。在反应温度为160℃、原料质量空速为1h~(-1)、苯酚与二壬基酚质量比为3:1的条件下,二壬基酚转化率达85.9%~90.6%,壬基酚收率达56.8%~67.2%,催化剂稳定性好,连续反应200h催化性能仍保持稳定。     

离子交换树脂催化合成对—1,1,3,3—四甲基丁基苯酚的研究

应用强酸性阳离子交换树脂作为苯酚与２,４,４－三甲基－１－戊烯及２,４,４－三甲基－２－戊烯的混合物（二异丁烯）进行烷基化反应的催化剂,通过间歇化反应,比较了三种树脂的催化活性。考察了反应时间、温度、二异丁烯与苯酚摩尔比及催化剂用量对转化率及目的产物选择性的影响。优化的反应条件为：温度８５℃,时间６ｈ,催化剂用量７％,二异丁烯与苯酚摩尔比０．８：１。在此条件下,二异丁烯转化率高于９５％,选择性可达     

离子交换树脂催化合成氯乙酸甲酯

本文以强酸型阳离子交换树脂为催化剂合成氯乙酸甲酯．研究了催化剂种类、催化剂用量、物料配比、催化剂使用次数及反应时间对反应的影响．实验结果表明，００１×７阳离子交换树脂催化效果较佳．该方法具有催化活性好，催化剂可循环使用和避免波硫酸污染的特点，转化率可达９３～９４％．     

磺酸型阳离子交换树脂催化合成肉桂酸甲酯

以磺酸型阳离子交换树脂为催化剂，由肉桂酸和甲醇合成了肉桂酸甲酯。考察了反应条件对酯化反应的影响和树脂的催化稳定性。结果表明，肉桂酸的转化率可达９５．５％，且催化剂的性能稳定。     

以N2O为氧化剂, Fe-P-O催化剂气相催化氧化苯制苯酚的研究

考察了应用N2O为氧化剂，FePO4、FePO4／SiO2、Fe0．5Al0.5PO4为催化剂气相催化氧化苯制苯酚的反应。在450℃下，FePO4催化剂上苯的转化率为2％，苯酚的选择性为85%；FePO4／SiO2(5％)催化剂上苯的转化率约为7％，苯酚的选择性为89％．Fe0．5Al0.5PO4催化剂可以使反应温度降低约100℃，350℃下反应苯的转化率为3．5％，苯酚的选择性为60％．分析表明，四面体结构的FeO4在该催化反应中具有重要的作用。     

TiO2/H2O2/超声波协同降解壬基酚聚氧乙烯醚溶液

采用经过处理的锐钛矿型TiO2作为催化剂,在H2O2存在下,以TiO2/H2O2/超声波协同降解壬基酚聚氧乙烯醚反应为模型,探讨了TiO2催化剂用量、H2O2用量、超声波功率、壬基酚聚氧乙烯醚溶液初始浓度、初始pH值对壬基酚聚氧乙烯醚降解率的影响。结果表明,在一定的超声波功率和一定的TiO2用量范围内,壬基酚聚氧乙烯醚降解率随超声波功率和TiO2用量的增大而增大,达到一定值后保持平稳;当H2O2浓度介于一定范围内,增大H2O2用量可提高壬基酚聚氧乙烯醚的降解率,但H2O2用量过多时,反而会使壬基酚聚氧乙烯醚的降解率下降;pH<5时,壬基酚聚氧乙烯醚降解效果较好,且pH值越小,降解率越高;pH>5时,降解率越来越低。TiO2/H2O2/超声波体系降解壬基酚聚氧乙烯醚产生了较强烈的协同效应,在同一时刻三者协同体系的降解率比其3种单独体系的降解率之和高出约60%;在TiO2催化剂用量0.4g/L、H2O2用量0.2g/L、超声波功率600W、降解时间120min的条件下,对初始质量浓度为80mg/L,pH=1的壬基酚聚氧乙烯醚溶液进行降解,其降解率达98%以上。     

壬基酚甜菜碱两性表面活性剂的合成和抗温耐盐性能

以壬基酚、环氧氯丙烷、二甲胺和3-氯-2-羟基丙磺酸钠为原料, 在催化剂的作用下经醚化、叔胺化、季铵化, 合成了壬基酚甜菜碱两性表面活性剂(NSZ), 并确定了最佳的反应条件。 壬基酚氯醇醚的最佳合成条件:物料比n(壬基酚):n(环氧氯丙烷)=1:4, 催化剂四丁基溴化铵用量为壬基酚用量的4%(摩尔比), 反应时间为4 h, 反应温度为95 ℃。 壬基酚叔胺的最佳合成条件:物料比为n(壬基酚氯醇醚):n(二甲胺):n(氢氧化钠)=1:2.5:1.1, 反应时间为4 h, 反应温度为60 ℃。 NSZ的最佳合成条件:以异丙醇/水为溶剂且其体积比为2:1, 反应温度为85 ℃, 反应时间24 h, n(3-氯-2羟基丙磺酸钠):n(壬基酚叔胺)=1.2:1, 反应体系的pH值为8~9。 通过测定NSZ在高温高矿化度条件下的界面性能、乳化性能和热稳定性, 证明了NSZ具有良好的耐温抗盐性能。     

超高交联树脂对壬基酚聚氧乙烯醚的吸附机理(英文)

研究了壬基酚聚氧乙烯醚(NPEO-10)在3种具有不同比表面积和孔径大小的超高交联树脂上的吸附行为与机理.3种超高交联树脂对壬基酚聚氧乙烯醚的吸附量受它们的比表面积和孔径大小以及溶液温度的影响.壬基酚聚氧乙烯醚在3种超高交联树脂上的吸附等温线可以用Langmuir和双Langmuir模型很好地拟合,而用Freundlich模型拟合则效果不好,但这些拟合曲线都具有相似的形状.热力学分析表明吸附过程主要表现为吸附质分子的疏水部分和吸附剂表面的作用以及吸附质分子在其表面形成胶束状的聚集体,即分散的、单层及双层聚集体的混合分布.吸附动力学曲线中的两个平台也证明了吸附过程存在单层和双层聚集体.脱附研究为实现超高交联树脂吸附分离水溶液中的壬基酚聚氧乙烯醚提供了合适的操作条件.     

用核磁共振研究壬基酚乙酸酯和壬基酚乙酮间的转位

采用核磁共振氢谱和碳谱研究了壬基酚乙酸酯和壬基酚乙酮转位的影响因素。     

壬基酚聚氧乙烯醚聚合度对水煤浆浆体性质的影响

研究了壬基酚聚氧乙烯醚型添加剂的聚合度对变质程度不同的8种煤所制得的水煤浆浆体性质的影响规律。结果表明,壬基酚聚氧乙烯醚添加剂的聚合度对于8种煤所制得的水煤浆的成浆性、流变性以及静态稳定性均有一定的影响,存在一最佳范围。研究还发现,用壬基酚聚氧乙烯醚型添加剂制备水煤浆时,该添加剂的作用与煤的分析基水分质量分数、丝质组分质量分数以及孔体积之间存在着相关性。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.