Thermal degradation of polystyrene

Molecular weight change studies have shown that the thermal degradation of random copolymers of styrene — namely HIPS, SAN, and ABS-at low temperatures and in air involves random chain scission. The dominant process in the degradation of HIPS is random chain scission due to weak links, whereas in SAN it is intermolecular chain transfer. In ABS, the degradation is initially random scission due to weak links and then mainly intermolecular chain transfer. The infrared spectra show that during degradation the labile weak links are attacked by oxygen and peroxidic free radicals are produced. Via hydrogen abstraction or autoxidation of olefinic links, these free radicals are responsible for the formation of aliphatic ketonic or peroxyester structures, and for isomerization and cyclization. The activation energies of overall degradation of HIPS, SAN, and ABS are 134, 142, and 92 kJ.mol^–1 respectively.Part of the PhD dissertation of Mrs. Jaya Nambiar, University of Gorakhpur, Gorakhpur-273001, 1980.     

Elastic moduli of ultradrawn polyethylene

The five independent elastic moduli C₁₁, C₁₂, C₁₃, C₃₃, and C₄₄ of oriented high-density polyethylene with draw ratio λ from 1 to 27 have been determined from ?60 to 100°C by an ultrasonic method at 10 MHz. At low temperature the sharp rise in the axial extensional modulus C₃₃ with increasing λ and the slight changes in the other moduli result from chain alignment and the increase in the number of intercrystalline bridges connecting the crystalline blocks. At high temperature (say, 100°C) the transverse extensional modulus C₁₁, as well as the axial (C₄₄) and transverse (C₆₆) shear moduli, also show substantial increases, reflecting the prominent reinforcing effect of stiff crystalline bridges in this temperature region where the amorphous matrix is rubbery. If the crystalline bridges are regarded as the fiber phase, the mechanical behavior can be understood in terms of the Halpin–Tsai equation for aligned short-fiber composites.     

Dimensional changes in ultradrawn polyethylene

Samples of ultradrawn high density polyethylene were studied by thermomechanical analysis. The purpose was to study the dimensional changes in polyethylene morphologies of extreme orientation. Dimensional changes were measured from ?140 to +70°C with a precision of better than 1%. A negative thermal expansion coefficient was observed along the length (c axis) of the fibers containing the polyethylene morphologies of extreme orientation. A change in negative coefficient is observed between ?35 and ?45°C. The sign and magnitude of the expansion coefficient confirm, along with other evidence, the existence of extended chain structures in these morphologies. A series-parallel model has been developed for the ultradrawn polyethylenes to describe the dimensional changes with temperature.     

Thermal expansion of polyoxymethylene

The thermal expensivities of polyoxymethylene crystals in the direction parallel (α_|^c) and perpendicular (α_‖^c) to the chain axis have been measured from 160 to 400 K using wide-angle x-ray diffraction. Although polyoxymethylene has a helical chain structure, it exhibits a thermal expansion behavior similar to that of polymer crystals with planar zigzag chains, namely that α_‖^c is negative while α_|^c is positive and larger by an order of magnitude. The negative α_‖^c arises from the shortening along the chain axis caused by the torsional and bending motions of the chain, whereas the large and positive α_|^c reflects the weak interaction across the chains. Combining the crystal data with dilatometric measurements on semicrystalline samples, the thermal expansivity is found to vary linearly with crystallinity, thus allowing the expansivity of the amorphous phase to be derived by extrapolation. With the thermal expansivities of the crystalline and smorphous phases known, the draw ratio dependence can be calculated in terms of existing models and is found to agree reasonably with experimental data.     

Tensile properties of ultradrawn polyethylene

High-density polyethylene filaments prepared by a solid-state deformation in an Instron capillary rheometer show unusually high crystal orientation, chain extension, axial modulus, and ultimate tensile strength. The Young's modulus and ultimate tensile strength have been determined from stress–strain curves. Gripping of this high modulus polyethylene has been a problem heretofore, but the measurement of ultimate tensile strength has now been made feasible by a special gripping procedure. Tensile moduli show an increase with sample preparation temperature and pressure. Values as high as 6.7 × 10¹¹ dyne/cm² are obtained from samples extruded at 134°C and 2400 atm and tested at a strain rate of 3.3 × 10^?4 sec^?1. The effect of strain rate and frequency on modulus has also been evaluated by a combination of stress–strain data and dynamic tension plus sonic measurements over nine decades of time.     

Thermal expansion of irradiated polyoxymethylene

The thermal expansion coefficient of gamma irradiated polyoxymethylene has been measured in the temperature range 80–340 K by using a three terminal capacitance technique. The radiation induced changes are measured by recording the i.r. spectra of the irradiated samples. The change in crystallinity caused by irradiation is measured by an X-ray technique. The thermal expansion coefficient increases with radiation dose below 170 K due to the predominant effect of degradation. Above 170 K, this trend reverses and the expansion coefficient decreases with radiation dose due to the increased crystallinity caused by irradiation.     

Thermal expansion of irradiated polytetrafluoroethylene

The thermal expansion coefficient of gamma-irradiated Polytetrafluoroethylene (PTFE) has been measured in the temperature range 80–340 K by using a three-terminal capacitance technique. The samples are irradiated in air at room temperature with gamma rays from a Co⁶⁰ source at a dose rate of 0.26 Mrad/h. The change in crystallinity is measured by an x-ray technique. The expansion coefficient is found to increase with radiation dose below 140 K owing to the predominant effect of degradation. Above 140 K, the expansion coefficient is found to decrease with radiation dose because of the enhanced crystallinity. The temperatures of the two first-order phase transitions are also found to shift to lower temperatures owing to degradation of PTFE.     

Pulsed NMR observation of ultradrawn polypropylene

Proton spin-spin relaxation times have been measured as a function of temperature for ultradrawn polypropylene with draw ratios λ up to 24. The three relaxation times T_2a (the longest), T_2i (intermediate), and T_2c (the shortest), observed for all the samples, have been ascribed to the relaxations of the amorphous, constrained amorphous, and crystalline components, respectively. T_2i and T_2a, which reflect the changes in structure and mobility in the noncrystalline regions, decrease with increasing λ; T_2i becomes saturated at λ > 9, whereas T_2a shows a substantial decrease up to λ = 24. The continued decrease in T_2a indicates that the constraint on the amorphous segments keeps increasing up to the highest λ. The associated mass fractions F_a, F_i, and F_c also change with λ. At λ < 9, the increasc in F_i with increasing λ is accompanied by a decrease in F_a, with F_c remaining unchanged. At higher λ, however, F_a is almost constant, and stepwise rises in F_c at about λ = 12 and 24 are accompanied by corresponding drops in F_i. It seems that, in this high draw ratio range, some of the taut molecules are fully extended and are in sufficiently good lateral register to transform into crystalline bridges. This conjecture is supported by the similarity in the λ dependence of F_c and the mass-fraction crystallinity obtained from the heat of fusion.     

Thermal expansion of structure-H clathrate hydrates

The temperature dependence of the unit cell parameters of two newly identified hexagonal structure clathrate hydrates of hexamethylethane (HME) and 2,2-dimethylbutane (DMB) have been measured by X-ray powder diffraction. The thermal expansion of the two distinct crystallographic axes was found to be inequivalent. However, the coefficients of cubic expansion are comparable to that in the cubic structure I and II hydrates. The larger thermal expansivity in the clathrate hydrates relative to ice is attributed to the weakening of the host lattice due to the internal pressure generated by the rattling motions of the encaged guests.Dedicated to Dr D. W. Davidson in honor of his great contributions to the sciences of inclusion phenomena.     

Thermal studies of fly ashes expansion

Journal of Thermal Analysis and Calorimetry - The object of this study is to investigate the thermal properties of fly ashes from the last, farthest dedusting zone in terms of their use as ceramic...     

Thermal expansion of a viscoelastic gel

It was previously shown [J. Non-Cryst. Solids, 130, 157 (1991)] that the permeability of a saturated gel can be determined from a measurement of its rate of expansion during a change in temperature. The existing analysis assumes that the solid network of the gel behaves elastically, but in many cases the gel is likely to be viscoelastic, especially when the gel exhibits syneresis. In this paper, the expansion kinetics are determined for a gel with a viscoelastic (VE) network. Sample calculations for a silica gel containing ethanol indicate that a naive application of the elastic analysis could result in errors exceeding a factor of two in the estimate of the permeability of a VE gel. However, in such cases, there are qualitative features in the experimental data that alert the experimenter to the existence of significant VE relaxation. Therefore, it is possible to avoid errors by careful examination of the data.     

Relaxation processes and structure of ultradrawn polyethylene

Solid-state extruded polyethylene fibers have been prepared, with a wide range of draw ratios and constant processing temperature. The draw ratios vary from 4 up to 30, and the processing temperature was always 398 K. The extruded material behaves anisotropically, owing to the high degree of chain orientation in the drawing direction. The modulus and linear expansion coefficients in the fiber axis direction have been measured, over a wide temperature range, from 140 K up to 320 K. These two properties are closely related to the degree of structural continuity of the fibers. A fibrous structure model is proposed to explain the temperature effects and the values obtained for the modulus and expansion coefficients, in terms of crystallinity and volumetric fraction of extended-chains structure. At least three relaxation processes can be identified which cause the structural continuity of the fibers to change with temperature.     

Thermal expansion effects in a silo

We consider a vertical container filled with granular material and exposed to temperature cycles which induce changes in the pressure distribution. Our starting point is an elastic model for the grains leading to classical Janssen behaviour in isothermal conditions. We assume complete mobilisation of the wall frictions. The dynamics superposes static friction plus a viscous friction. After a T jump favouring an expansion, we predict that the resulting overpressures are relaxed only in a region (of size comparable to the Janssen screening length λ) near the top. When T returns to the initial value, we expect decohesion in a certain layer near the top (for rapid cooling). For slow cooling, we expect a smooth return to the original Janssen state. We also discuss a different, but related, effect: instead of changing the temperature, we switch off the gravity effects (on a small column) by suddenly rotating the column from vertical to horizontal. Here, a rarefaction wave should invade the whole column.