Compatibility in poly(ethylene oxide)–poly(methyl methacrylate) blends

The compatibility of poly(ethylene oxide)-poly(methyl methacrylate) (PEO-PMMA) blends were examined covering the complete composition range. Up to 20% of PEO content films were transparent and glass transition temperatures were determined by DSC and by refractive index vs. temperature measurements. Only one T_g was obtained for these samples and the relationship between T_g and composition has been evaluated. At higher PEO content crystallization took place and the films were opaque. Melting temperatuures of PEO in blends were determined by DSC. Melting point depression was observed for increasing proportion of PMMA and the binary interaction parameter has been calculated.     

Morphology of poly(ethylene oxide)/poly(vinyl acetate) blends

The morphology of poly(ethylene oxide)/poly(vinyl acetate) (PEO/PVAc) blends was examined using small angle X-ray scattering (SAXS) and optical microscopy. The morphological and structural parameters of the blends are dependent on both composition and crystallization conditions. Optical microscopy revealed that blend samples prepared by solution casting crystallized with volume-filling crystals up to a composition of 30/70 wt% PEO/PVAc; at higher PVAc content there was no evidence of crystallization in the temperature range studied. Pure PEO always crystallized with a spherulite-hedrite morphology. The formation of spherulites was relatively favoured at lower crystallization temperatures and by addition of PVAc to PEO. Small angle X-ray intensity profiles were analyzed using a recently developed methodology and it was found that, for a given crystallization temperature, the amorphous and interphase thicknesses increased with increasing PVAc content but that the average crystalline thickness was independent of composition. The morphological and structural properties of the PEO/PVAc blends were attributed to the presence of non-crystallizable material in both the interlamellar and interfibrillar regions.     

Compatibility of poly(ethylene oxide)/poly(vinyl chloride) blends by differential scanning calorimetry

This article refers to a study of the thermal behaviour of poly(ethylene oxide) and poly(vinyl chloride) blends in the solid state. The compatibility has been examined by differential scanning calorimetry. The influence of molecular masses of the polymers on their compatibility has been shown. The equilibrium melting temperatures decrease in the mixture, such behaviour being progressively greater with the PEO reduction. The melting temperature of blends increases linearly with the crystallization temperature for a wide range of undercooling. Values of the parameters χ₁₂ and B have been obtained.     

Viscoelasticity and tack of poly(vinyl pyrrolidone)–poly(ethylene glycol) blends

The adhesive properties of blends of high molecular weight poly(vinyl pyrrolidone) (PVP) and low molecular weight poly(ethylene glycol) (PEG) were systematically investigated with a probe test and correlated with their viscoelastic properties. The material parameters that were varied were the PEG content (31–41 wt %) and the hydration rate. The 36% PEG showed the best balance of properties for a pressure‐sensitive adhesive. At low debonding rates, the debonding took place through the formation of a fibrillar structure, whereas at high debonding rates, the debonding was brittle. This transition was attributed to the breakage and reformation of hydrogen bonds between PVP units and OH groups on PEG during the large strain of the polymer chains in elongation. This transition was observed, albeit shifted in frequency, for all three compositions, and the characteristic relaxation times of the hydrogen‐bonded network were estimated. A comparison between the tack properties of the adhesives and their linear viscoelastic properties showed a very strong decoupling between the small‐strain and large‐strain properties of the adhesive, which was indicative of a pronounced deviation from rubber elasticity in the behavior of the blends. This deviation, also seen during tensile tests, was attributed to the peculiar phase behavior of the blends. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2395–2409, 2002     

Synthesis and block‐specific complexation of poly(ethylene oxide)–poly(tetrahydrofuran)–poly(ethylene oxide) triblock copolymers

Well‐defined ABA triblock copolymers in which A stands for poly(ethylene oxide) (PEO) and B for poly(tetrahydrofuran) (PTHF) were synthesized by end‐capping bifunctionally living PTHF with different polyethylene glycol–monomethylethers. Differential scanning calorimetry analysis of these copolymers showed two melting points: one around 55 °C due to the PEO blocks, and one around 30 °C due to the PTHF segments, demonstrating that these block copolymers show extensive phase separation. Upon addition of sodium thiocyanate, crystalline complexes with PEO were formed and as a consequence, the melting points of the PEO segments had shifted to approximately 170 °C, whereas the melting points of the PTHF segments decreased slightly. The obtained materials behave as thermoplastic elastomers up to 160–175 °C. The influence of the relative lengths of the PEO and the PTHF segments on the thermal and mechanical properties of the materials have been investigated. Copyright © 1999 John Wiley & Sons, Ltd.     

Morphology and properties of poly(vinyl chloride)–poly(butadiene-co-acrylonitrile) blends

The objective of this research was to study the structure-property relationships of two poly(vinyl chloride) (PVC)–poly(butadiene-co-acrylonitrile) (BAN) blends which exhibit differences in blend compatibility. Studies were carried out utilizing differential scanning calorimetry, dynamic mechanical testing, stress–strain, transmission electron microscopy (TEM), and infrared dichroism experiments at different temperatures. The BAN 31/PVC (BAN containing 31% acrylonitrile) system is considered to be nearly compatible as evidenced by T_g shifts, stress–strain results, orientation characteristics, and TEM micrographs. Similar experiments indicate that the BAN 44/PVC system is incompatible, and contains a mixed phase of BAN 44-PVC and a pure BAN 44 phase. The extent of heterogeneity in the compatible BAN 31/PVC system, however, plays an important role in the orientation characteristics of the blends.     

Studies of photooxidative degradation of poly(vinyl chloride)/poly(ethylene oxide) blends

The photooxidative degradation of blends (in a full range of compositions) of amorphous poly(vinyl chloride) (PVC) with semicrystalline poly(ethylene oxide) (PEO) in the form of thin films is investigated using absorption spectroscopy (UV–visible and Fourier transform infrared) and atomic force microscopy (AFM). The amount of insoluble gel formed as a result of photocrosslinking is estimated gravimetrically. It is found that the PVC/PEO blendsí susceptibility to photooxidative degradation differs from that pure of the components and depends on the blend composition and morphology. Photoreactions such as degradation and oxidation are accelerated whereas dehydrochlorination is retarded in blends. The photocrosslinking efficiency in PVC/PEO blends is higher than in PVC; moreover, PEO is also involved in this process. AFM images showing the lamellar structure of semicrystalline PEO in the blend lead to the conclusion that the presence of PVC does not disturb the crystallization process of PEO. The changes induced by UV irradiation allow the observation of more of the distinct PEO crystallites. This is probably caused by recrystallization of short, more mobile chains in degraded PEO or by partial removal of the less stable amorphous phase from the film surface. These results confirm previous information on the miscibility of PVC with PEO. The mechanism of the interactions between the components and the blend photodegradation are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 585–602, 2004     

Compatibility studies of polystyrene and poly(vinyl acetate) blends using electrostatic force microscopy

The effect of thermal treatment on the phase separation process of the components of a polymer blend was investigated using electrostatic force microscopy (EFM). EFM technique is an advance on conventional atomic force microscopy, which enables us to measure locally the dielectric properties of the samples under investigation providing compositional information. In this work, we studied the phase separation process of the polymer blend thin films made of polystyrene and poly(vinyl acetate) (PS/PVAc) (75/25 weight fraction). The samples were subjected to different thermal treatments. It was found that at low annealing temperature, PVAc forms many small islands within PS matrix. As the annealing temperature increases, the number of PVAc islands decreases with an increase in the size of the islands. These islands take spherical‐like shape when annealed at a temperature well above the glass transition temperatures of both the component polymers. Despite these morphological/topographical changes, EFM images evidence that there is no interdiffusion which was further confirmed by quantitatively measuring the value of the dielectric permittivity across the interphase. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1332–1338, 2011     

Poly(vinyl chloride)–poly(ethylene oxide) block copolymers: Synthesis and characterization

Poly(vinyl chloride)-poly(ethylene oxide) block copolymers have been synthesized in solution and emulsion. The polymers were made by first synthesizing macroazonitriles through the reaction of 4,4′-azobis-4-cyanovleryl chloride with hydroxy-terminated poly(ethylene oxide) of varying molecular weights. These macroazonitriles had molecular weights in the range of 3000–88,000 and degrees of polymerization from 5 to 24. Thermal decomposition of the azolinkages in the presence of vinyl chloride monomer yielded block copolymers containing form 2 to 20 wt % poly(ethylene oxide). The structures of the block copolymers were characterized by spectrometric, elemental and molecular weight analyses. The possibility of some graft polymerization occurring via free-radical extraction of a methylene hydrogen from the poly(ethylene oxide) was considered. Polymerization of vinyl chloride with an azonitrile initiator in the presence of a poly(ethylene oxide) yielded predominately homopolymer with some grafted poly(vinyl chloride).     

Miscible blends of poly(ethylene oxide) with brush copolymers of poly(vinyl alcohol)‐graft‐poly(l‐lactide)

Even though poly(ethylene oxide) (PEO) is immiscible with both poly(l ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA), this article shows a working route to obtain miscible blends based on these polymers. The miscibility of these polymers has been analyzed using the solubility parameter approach to choose the proper ratios of the constituents of the blend. Then, PVA has been grafted with l ‐lactide (LLA) through ring‐opening polymerization to obtain a poly(vinyl alcohol)‐graft‐poly(l ‐lactide) (PVA‐g‐PLLA) brush copolymer with 82 mol % LLA according to ¹H and ¹³C NMR spectroscopies. PEO has been blended with the PVA‐g‐PLLA brush copolymer and the miscibility of the system has been analyzed by DSC, FTIR, OM, and SEM. The particular architecture of the blends results in DSC traces lacking clearly distinguishable glass transitions that have been explained considering self‐concentration effects (Lodge and McLeish) and the associated concentration fluctuations. Fortunately, the FTIR analysis is conclusive regarding the miscibility and the specific interactions in these systems. Melting point depression analysis suggests that interactions of intermediate strength and PLOM and SEM reveal homogeneous morphologies for the PEO/PVA‐g‐PLLA blends. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1217–1226     

Thermal degradation of poly(vinyl chloride)/poly(ethylene oxide) blends: Thermogravimetric analysis

Thermal stability of poly(vinyl chloride)/poly(ethylene oxide) (PVC/PEO) blends has been investigated by thermogravimetric analysis (TGA) in dynamic and isothermal heating regime. PVC/PEO blends were prepared by hot-melt extrusion (HME). According to TG analysis, PEO decomposes in one stage, while PVC and PVC/PEO blends in two degradation stages. In order to evaluate the effect of PEO content on the thermal stability of PVC/PEO blends, different criteria were used. It was found that thermal stability of PVC/PEO blends depends on the blend composition. The interactions of blends components with their degradation products were confirmed. By using multiple heating rate kinetics the activation energies of the PVC/PEO blends thermal degradation were calculated by isoconversional integral Flynn–Wall–Ozawa and differential Friedman method. According to dependence of activation energy on degree of conversion the complexity of degradation processes was determined.     

Polyacrylamide–graft–poly(ethylene oxide)

Water-soluble graft copolymers were synthesized by copolymerization of acrylamide with mono-methoxy-poly(ethylene oxide)-methacrylates (Me-PEO-MA). The Me-PEO-MA macromers were synthesized by a catalytic esterification of methacrylic acid with mono-methoxy-poly(ethylene glycol)s with different molecular weights. The graft copolymers obtained were characterized by ¹H-NMR spectroscopy, gel permeation chromatography (GPC) and Ubbelohde viscosimetry. The rheological behaviour of aqueous polymer solutions, which are expected to show hydrophobic association at elevated temperatures, was studied with a cone and plate-rheometer.     

Effect of aging on fractional crystallization of poly(ethylene oxide) component in poly(ethylene oxide)/poly(3‐hydroxybutyrate) blends

The effect of aging on the fractional crystallization of the poly(ethylene oxide) (PEO) component in the PEO/poly(3‐hydroxybutyrate) (PHB) blend has been investigated. The partial miscibility of the PEO/PHB blends with high PEO molecular weight (M_v = 2.0 × 10⁵ g/mol) was confirmed by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis. The fractional crystallization behavior of the PEO component in the PEO/PHB blends with low PEO content (not more than 30 wt% of PEO), before and after aging under vacuum at 25 °C for 6 months, were compared by DSC, fourier transform infrared microscopic spectroscopy, small angle X‐ray diffraction, and scanning electron microscopy. It was confirmed that nearly all the PEO components remain trapped within interlamellar regions of PHB for the PEO/PHB blends before aging. Under this condition, the crystallization of PEO is basically induced by much less active heterogeneities or homogeneous nucleation at high supercoolings. While, after the same PEO/PHB samples were stored at 25 °C in vacuum for 6 months, a part of the PEO component was expelled from the interlamellar region of PHB. Under this condition, the expelled PEO forms many separate domains with bigger size and crystallizes at low supercoolings by active heterogeneous nucleation, whereas the crystallization of PEO in the interlamellar region is still mainly induced by less active heterogeneities or homogeneous nucleation at extreme supercoolings. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2665–2676, 2005     

Electrical conductivity of thermally degraded poly(vinyl chloride)–polyacrylonitrile blends

Finely powdered blends of poly(vinyl chloride) (PVC) and polyacrylonitrile (PAN) have been thermally degraded at 275°C for 24 h in an inert atmosphere to effect complete de-hydrochlorination of PVC to a conjugated polyene structure and simultaneous internal polymerization of nitrile groups in PAN to a conjugated polyimine sequence. The room temperature d.c. conductivity of the degraded blends showed clear synergistic behavior. A maximum conductivity has been observed with a blend of 60 PAN/40 PVC which is about 4 orders of magnitude over the linearly weighted average conductivity of the individual degraded homopolymers. The results have been interpreted in terms of a possible donor-acceptor interaction between the degraded homopolymers leading to mutual doping and, hence, an enhanced electrical conductivity. © 1995 John Wiley & Sons, Inc.     

Carbon-13 NMR of poly(vinyl acetate) and ethylene–vinyl acetate copolymer

Carbon-13 nuclear magnetic resonance spectra of atactic poly(vinyl acetate) and ethylene–vinyl acetate copolymers are reported and analyzed. Carbon spectra at 22.6 and 62.9 MHz together with use of shift reagents have permitted a more complete assignment than previously reported; in some cases the published assignments are found to be in error.     

Compatibility of binary systems of poly(methyl methacrylate), poly(vinyl chloride) and poly(vinyl acetate)

The influence of the thermal treatment on the stability in time of the dispersion degree of films containing binary polymer mixtures, poly(vinyl chloride)/poly(methyl methacrylate), poly(vinyl chloride)/poly(vinyl acetate) and poly(vinyl acetate)/poly(methyl methacrylate), was studied by thermogravimetry and optical microscopy with phase contrast. The dispersion degree depends particularly on the composition of the polymer mixture and can be improved by thermal treatment at temperatures above the glass temperatures of both homopolymers. It seems that this thermal treatment yields exclusively metastable structures with a general tendency to phase separation in a short time after thermal treatment, the heterogeneity mixtures (as film) being more pronounced.     

A dielectric study of poly(ethylene-co-vinyl acetate)–poly(vinyl chloride) blends. II. Loss curve broadening and correlation parameters

Normalized dielectric loss curves for blends of PVC with an EVA copolymer containing 70% vinyl acetate showed significant broadening with increasing PVC content. In conjunction with phase separation studies it was concluded that increasing loss curve broadness correlated with increasing tendency toward phase separation. Calculation of correlation parameters for the blends revealed differences in intermolecular correlations with blend composition.     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

Miscible blends of poly(vinyl phenyl ketone) and poly(4‐vinyl phenol)

An analysis by differential scanning calorimetry, modulated differential scanning calorimetry, and Fourier transform infrared spectroscopy (FTIR) indicates that blends of poly(vinyl phenyl ketone) (PVPhK) and poly(4‐vinyl phenol) (P4VPh) are miscible at ambient temperature. Miscibility, ascertained, is supported by the existence of a single glass transition for each composition of the PVPhK/P4VPh blends. The FTIR spectroscopy analysis demonstrates the formation of hydrogen bonds between carbonyl groups of PVPhK and hydroxyl groups of P4VPh. This specific interaction has a crucial role on the miscibility behavior of PVPhK/P4VPh blends. The evolution of the glass transition of the PVPhK, P4VPh, and its blends as a function of mixture composition shows negative deviations with to respect to the ideal mixing rule, and both Fox and Gordon–Taylor equations predict this behavior successfully. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2404–2411, 2006