Radical homo- and copolymerizations of methyl α-trifluoroacetoxyacrylate

Radical homo- and copolymerizations of methyl α-trifluoroacetoxyacrylate (MTFAA) are studied by using azo initiators at 40 and 60°C. The rate of the homopolymerization of MTFAA was lower than that of methyl α-acetoxyacrylate. Monomer reactivity ratios (r), and Q and e values were estimated to be r₁ = 0.03, r₂ = 0.27, Q₁ = 0.65, and e₁ = 1.38 from the copolymerization of MTFAA (M₁) and styrene (M₂) at 60°C. Preferential crosspropagation was observed in particular in the copolymerization of MTFAA and α-methylstyrene. The influence of replacing the hydrogens of the acetoxy moiety of the acyloxyacrylate with the fluorines upon the copolymerization reactivity is discussed on the basis of the ¹³C-NMR chemical shift of various acyloxyacrylates. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3537–3541, 1997     

Radical polymerization of butadiene-1-carboxylic acid

The homopolymerization and copolymerization of butadiene-1-carboxylic acid (Bu-1-Acid) (M₁) were studied in tetrahydrofuran at 50°C with azobisisobutyronitrile as an initiator. The initial rate of polymerization was proportional to [AIBN]^1/2 and [Bu-1-Acid]¹. The overall activation energy for the polymerization was 22.87 kcal/mole. For copolymerization with styrene (M₂) and acrylonitrile (M₂), the monomer reactivity ratios r₁, r₂ were determined by the Fineman-Ross method, as follows; r₁ = 5.55, r₂ = 0.08 (M₂ = styrene); r₁ = 11.0, r₂ = 0.03 (M₂ = acrylonitrile). Alfrey-Price Q-e values calculated from these values were 6.0 and +0.11, respectively. The Bu-1-Acid unit in the copolymer as well as the homopolymer was found from infrared and NMR spectral analyses to be composed of a trans-1,4 bond. The hydrogen-transfer polymerization of Bu-1-Acid leading to polyester was attempted with triphenylphosphine as initiator, but did not occur.     

Polymerization of β-cyanopropionaldehyde. X. Anionic copolymerization with methyl isocyanate

Anionic copolymerization of β-cyanopropionaldehyde (M₁) with methyl isocyanate (MeI, M₂) was studied with use of benzophenone–dilithium complex as initiator at ?78°C. The values of monomer reactivity ratio were determined to be r₁ = 8.3 ± 0.3 and r₂ = 0.01 ± 0.01. The structure of resulting copolymer was investigated by means of NMR analysis. The MeI unit is presumed to enter the copolymer chain through its C?N opening.     

Radiation copolymerization of vinylene carbonate with isobutyl vinyl ether

The radiation-induced copolymerization of vinylene carbonate (M₁) with isobutyl vinyl ether (M₂) has been investigated over the temperature range of 40–80°C. The monomer reactivity ratios r₁ and r₂ were determined to be 0.118 and 0.148, respectively, and an activation energy of 7.6 kcal/mole (31.8 kJ/mole) was calculated for the copolymerization process.     

Alternating polyampholytes prepared by hydrolysis of copolymer of maleic anhydride and N-vinylsuccinimide

Alternating polyampholytes (MA-VA) containing two acidic groups and one basic group were prepared by the copolymerization of maleic anhydride (M₁) and N-vinylsuccinimide (M₂) at 60°C with AIBN as the initiator, followed by acid hydrolysis with 1N hydrochloric acid at 140°C for 24 hr. The monomer reactivity ratios r₁ and r₂ are 0.025 and 0.06, respectively. The structure of polymers was discussed on the basis of the data of their elementary, infrared (IR), and thermal analyses and the binding ability of heavy metal ion. Polyampholytes were soluble in strong acidic and basic media but were precipitated in the pH range 3–4. An isoelectric point at pH 3 was determined by potentiometric titration and the turbidimetric method. By thermal treatment above 205°C the polyampholyte turned quantitatively into a cyclized lactam. This suggests that the polyampholyte MA–VA has an intramolecular hydrogen bond between the amino and γ-carboxyl groups. The binding of Cu²⁺ and Hg²⁺ by the polyelectrolyte was evaluated by equilibrium dialysis.     

Silyl enol ethers as monomer. III. Radical polymerization and copolymerizations of 2-trimethylsilyloxy-1,3-butadiene and desilylation of the resulting polymers

2-Trimethylsilyloxy-1,3-butadiene (TMSBD), the silyl enol ether of methyl vinyl ketone, was homopolymerized with a radical initiator to afford polymers with a molecular weight of ca. 10⁴. Radical copolymerizations of TMSBD with styrene (ST) and acrylonitrile (AN) in bulk or dioxane at 60°C gave the following monomer reactivity ratios: r₁ = 0.64 and r₂ = 1.20 for the ST (M₁)–TMSBD (M₂) system and r₁ = 0.036 and r₂ = 0.065 for the AN (M₁)–TMSBD (M₂) system. The Q and e values of TMSBD determined from the reactivity ratios for the former copolymerization system were 2.34 and ?1.31, respectively. The resulting polymer and copolymers were readily desilylated with hydrochloric acid or tetrabutylammonium fluoride as catalyst to yield analogous polymers having carbonyl groups in the polymer chains.     

Solution copolymerization of styrene and 2-hydroxyethyl mechacrylate.

The rate of solution copolymerization of styrene (M₁) and 2-hydroxyethyl methacrylate (M₂) was investigated by dilatometry. N,N-dimethyl formamide, toluene, isopropyl alcohol, and butyl alcohol were used as solvents. Polymerization was initiated by α,α′-azobisisobutyronitrile at 60°C. The initial copolymerization rate increased nonlinearly with increasing 2-hydroxyethyl methacrylate (HEMA)/styrene ratio. The copolymerization rate was promoted by solvents containing hydroxyl groups. Two different approaches were used for the prediction of copolymerization rates. The relationships proposed for the copolymerization rates calculation involve the effects of the total monomer concentration, mole fraction of HEMA, and of the solvent type. Different reactivity ratios were found in polar and nonpolar solvents: r₁ = 0.53, r₂ = 0.59 in N,N-dimethyl formamide, isopropyl alcohol and n-butyl alcohol; r₁ = 0.50, r₂ = 1.65 in toluene. The usability of these reactivity ratios was confirmed by batch experiments.     

Radical-initiated homo- and copolymerizations of methacryloyl fluoride

The kinetics of methacryloyl fluoride (MAF) homopolymerization was investigated in methyl ethyl ketone (MEK) with azobis(isobutyronitrile) as initiator. The rate of polymerization (R_p) followed the expression R_p = k[AIBN]^0.55[MAF]^1.18. The overall activation energy was calculated as 74.4 kJ/mol. The relative reactivity ratios of MAF(M₂) copolymerization with styrene (r₁ = 0.083, r₂ = 0.14), and methyl methacrylate (r₁ = 0.48, r₂ = 0.81) in methyl ethyl ketone were obtained. Application of the Q–e scheme (in styrene copolymerization) led to Q = 2.22 and e = 1.31. The glass transition temperature (T_g) of poly(MAF) was 90°C by thermomechanical analysis. Thermogravimetry of poly(MAF) showed a 10% weight loss of 228°C in air.     

Radical polymerization behavior of trimethoxyvinylsilane

Trimethoxyvinylsilane (TMVS) was quantitatively polymerized at 130 °C in bulk, using dicumyl peroxide (DCPO) as initiator. The polymerization of TMVS with DCPO was kinetically studied in dioxane by Fourier transform near‐infrared spectroscopy. The overall activation energy of the bulk polymerization was estimated to be 112 kJ/mol. The initial polymerization rate (R_p) was expressed by R_p = k[DCPO]^0.6[TMVS]^1.0 at 120 °C, being closely similar to that of the conventional radical polymerization involving bimolecular termination. The polymerization system involved electron spin resonance (ESR) spectroscopically observable polymer radicals under the actual polymerization conditions. ESR‐determined apparent rate constants of propagation and termination were 13 L/mol s and 3.1 × 10⁴ L/mol s at 120 °C, respectively. The molecular weight of the resulting poly(TMVS)s was low (M_n = 2.0–4.4 × 10³), because of the high chain transfer constant (C_mtr = 4.2 × 10^?2 at 120 °C) to the monomer. The bulk copolymerization of TMVS (M₁) and vinyl acetate (M₂) at 120 °C gave the following copolymerization parameters: r_l = 1.4, r₂ = 0.24, Q₁ = 0.084, and e₁ = +0.80. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5864–5871, 2005     

Photosensitized copolymerization of optically active N-l-menthylmaleimide with styrene and methyl methacrylate

Photosensitized copolymerization of optically active N-l-menthylmaleimide (NMMI) with styrene (Sty) and methyl methacrylate (MMA) was carried out in tetrahydrofuran (THF) at 30°C with benzoyl peroxide (BPO). The monomer reactivity ratios for the copolymerization of NMMI (M₂) with Sty (M₁) and MMA (M₁) were r₁ = 0.08 ± 0.10, r₂ = 0.20 ± 0.05 and r₁ = 2.85 ± 0.06, r₂ = 0.07 ± 0.06, respectively. Copoly-MMA–NMMI and poly-NMMI showed positive circular dichroism(CD) curves of equal intensity and shape over the wavelength region from 230 to 270 nm; copoly-Sty–NMMI also showed a positive CD curve which was similar in shape but was different in intensity from that of poly-NMMI. The correlation between monomer unit ellipticity of the copolymers and their composition would suggest the alternating and stereoregular copolymerization of NMMI with Sty.     

Water-soluble copolymers. XLII. Cationic polyelectrolytes of acrylamide and 2-acrylamido-2-methylpropanetrimethylammonium chloride

The new monomer 2-acrylamido-2-methylpropanetrimethylammonium chloride (AMP-TAC, M₂) has been synthesized. Free radical copolymerization with acrylamide (AM, M₁) in feed ratios varying from 10 to 50 mol % AMPTAC gave the cationic ATAM series. Copolymer compositions were determined from ¹³C-NMR. The reactivity ratio product r₁r₂ was found to be 0.62. Molecular weights varied from 1.4 to 16.5 × 10⁶ g/mol for the copolymers. Turbidimetric studies showed aqueous solutions of the copolymers to be phase stable in the presence of CaCl₂ and Na₂CO₃ up to 100°C. Solution behavior was independent of pH in the range of 3 to 11, and temperature in the range of 25 to 60°C. Intrinsic viscosities of the cationic copolymers decreased with the addition of electrolytes; however, some samples showed curvature in plots of intrinsic viscosity versus the inverse square root of ionic strength. © 1993 John Wiley & Sons, Inc.     

Reactive oligomers. I. Preparation and polymerization of ethylene glycol bis(methyl fumarate)

Ethylene glycol bis(methyl fumarate) (EGBMF) was prepared as a new type of divinyl compound and reactive oligomer: a needle crystal, m.p. 104.5°C. Homopolymerization of EGBMF was carried out in dioxane with 0.1 mol/L AIBN at [M] = 1 mol/L and 60°C; the rate of polymerization was estimated to be 4.44 × 10^?6 mol/L s in a good agreement with diethyl fumarate (DEF). The cyclization constant K_c was obtained as 1.64 mol/L, being rather low compared with diallyl oxalate which is 1,9-diene having two ester groups analogous to EGBMF. Gelatin occurred at about 35% conversion. Finally, the copolymerization of EGBMF (M₁) with diallyl phthalate (DAP) (M₂) is tentatively explored with the intention of the improvement of allyl resins in mechanical properties; remarkable rate enhancement was observed for copolymerization. The monomer reactivity ratios were estimated to be r₁ = 0.96 and r₂ = 0.025, the r₁ value being reduced compared with the DEF-DAP copolymerization system. These results are discussed from the standpoint of steric effect on the polymerization of fumarate as an internal olefin.     

Sulfur-Containing Vinyl Monomers. XIX. Radical Polymerization of 2-Mercaptobenzothiazolyl Methacrylate

2-Mercaptobenzothiazolyl methacrylate (MBTM) was synthesized by the reaction of 2-mercaptobenzothiazole and methacrylyl chloride in tetrahydrofuran at -18°C. MBTM was found to polymerize in the presence of 2,2′-azobisisobutyronitrile (AIBN), n-BuLi, and UV light. From the kinetic studies of radical polymerization of MBTM with AIBN in benzene at 60°C, the overall activation energy was determined to be 18.9 kcal/mole, and the rate of polymerization (R) was expressed as R_p = k[AIBN]^0.5 [MBTM], where k is the overall polymerization rate constant. From these results this polymerization was confirmed to proceed via an ordinary radical mechanism. This monomer (M₂) was also copolymerized radically with styrene (M₁) at 60°C, and the resulting copolymerization parameters were determined as r₁ = 0.042, r₂ = 0.20, Q₂ = 4.09, and e₂ = 1.39. The thermal stability and the photodegradation behavior of the polymers were examined, and they were compared with those of the related polymers.     

N-vinylpyrrolidone and 4-vinyl Benzylchloride Copolymers: Synthesis,Characterization and Reactivity Ratios

The copolymers prepared in this study by free radical copolymerization of N-vinylpyrrolidone (M ₂) with 4-vinylbenzylchloride (M ₁) using 2,2′-azobisisobutyronotrile (AIBN) initiator in 1,4-dioxane solvent at 70°C were characterized by FTIR, ¹H-NMR and ¹³C-NMR techniques. Polymer solubility was tested in both polar and nonpolar solvents. The thermal properties were studied by thermogravimetric analysis (TGA) and differential scanning calorimeter (DSC). Copolymer compositions were established by H¹-NMR spectra, while reactivity ratios of the monomers were computed using the linearization methods viz., Fineman-Ross (FR) (r ₁ = 1.67 and r ₂ = 0.67), Kelen-Tudos (KT) (r ₁ = 1.77 and r ₂ = 0.65) and extended Kelen-Tudos (EK-T) (r ₁ = 1.72 and r ₂ = 0.63) methods at lower conversion. Furthermore, reactivity ratios in nonlinear error-in-variables method (RREVM) also compute the reactivity ratios (r ₁ = 1.76 and r ₂ = 0.66); these are found to be in good agreement with each other. The distribution of monomer sequence along the copolymer chain was calculated using a statistical method based on the calculated reactivity ratios.     

Olefin copolymerization with metallocene catalysts. II. Kinetics,cocatalyst, and additives

The kinetics of ethylene/propylene copolymerization catalyzed by (ethylene bis (indeyl)-ZrCI₂/methylaluminoxane) has been investigated. Radiolabeling found about 80% of the Zr to be catalytically active. The estimates for rate constants at 50°C are k₁₁ = 1104 (M_s)^?1, k₁₂ = 430 (M_s)^?1, k₂₂ = 396 (M_s)^?1,k₂₁ = 1020 (M_s)^?1, and k^A_tr,1 + k^A_tr.2 = 1.9 × 10^?3 s^?1. Substitution of trimethylaluminum for methylaluminoxane resulted in proportionate decrease in polymerization rate. The molecular weight of the copolymer is slightly increased by loweing the [Al]/[Zr] ratio, or addition of Lewis base modifier but at the expense of lowered catalytic activity and increase in ethylene content in the copolymer. Lowering of the polymerization temperature to 0°C resulted in a doubling of molecular weight but suffered 10-fold reduction in polymerization activity and increase of ethylene in copolymer.     

Radical polymerization of ortho-(1,3-dioxolan-2-yl)phenyl ethyl fumarate involving intramolecular hydrogen abstraction and ring opening of cyclic acetal

The polymerization of o-(1,3-dioxolan-2-yl)phenyl ethyl fumarate (DOPEF) initiated with dimethyl 2,2′-azobisiso-butyrate (MAIB) was studied kinetically in benzene. The polymerization rate (R_p) at 60°C was given by R_p = k [MAIB]^0.76 [DOPEF]^0.71. The overall activation energy of polymerization was calculated to be 98.3 kJ/mol. The number-average molecular weight of resulting poly(DOPEF) was in the range of 1000–3100. ¹H- and ¹³C-NMR spectra of resulting polymers revealed that the radical polymerization of DOPEF proceeds in a complicated manner involving vinyl addition, intramolecular hydrogen abstraction, and further ring opening of the cyclic acetal at higher temperatures. From the copolymerization of DOPEF (M₁) and styrene (St) (M₂) at 60°C, the monomer reactivity ratios were obtained to be r₁ = 0.02 and r₂ = 0.20, the values of which are similar to those of the copolymerization of ethyl o-formylphenyl fumarate and St. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 563–572, 1998     

Aminobutadienes. X. Polymerization and copolymerization of 2-phthalimidomethyl-1,3-butadiene

The polymerization and copolymerization of 2-phthalimidomethyl-1,3-butadiene were investigated. This monomer was easily polymerized by benzoyl peroxide catalyst in bulk or in solvent, and by γ-radiation in the solid state to give polymers having a softening point of 135–145°C. Although these resulting polymers did not give x-ray diffraction patterns, they showed crystalline patterns by electron diffraction. On the other hand, cationic polymerization with the use of boron trifluoride diethyl etherate in chloroform was attempted, but no formation of the polymer was observed. Also, this monomer was easily copolymerized with styrene in N,N-dimethylformamide. The monomer reactivity ratios and Alfrey-Price Q and e values calculated from the copolymerization data of this monomer (M₁) with styrene (M₂) were r₁ = 2.0 ± 0.13, r₂ = 0.15 ± 0.02, and Q₁ = 2.78, e₁ = 0.30.     

Silyl enol ethers as monomer. I. Radical copolymerizability of α-trimethylsilyloxystyrene

α-Trimethylsilyloxystyrene (TMSST), the silyl enol ether of acetophenone, was not homopolymerized either by a radical or a cationic initiator. Radical copolymerization of TMSST with styrene (ST) and acrylonitrile (AN) in bulk and the terpolymerization of TMSST, ST, and maleic anhydride (MA) in dioxane were studied at 60°C and the polymerization parameters of TMSST were estimated. The rate of copolymerization decreased with increased amounts of TMSST for both systems. Monomer reactivity ratios were found as follows: r₁ = 1.48 and r₂ = 0 for the ST (M₁)–TMSST (M₂) system and r₁ = 0.050 and r₂ = 0 for the AN (M₁)–TMSST (M₂) system. The terpolymerization of ST (M₁), TMSST (M₂), and MA (M₃) gave a terpolymer containing ca. 50 mol % of MA units with a varying ratio of TMSST to ST units and the ratio of rate constants of propagation, k₃₂/k₃₁, was found to be 0.39. Q and e values of TMSST were determined using the values shown above to be 0.88 and ?1.13, respectively. Attempted desilylation by an acid catalyst for the copolymer of TMSST with ST afforded polystyrene partially substituted with hydroxyl groups at the α-position.     

Radical Copolymerization of Vinylidene Chloride with 3(2-Methyl)-6-methylpyridazinone in Several Solvents

The radical copolymerization of vinylidene chloride (Vc, M₁) with 3(2-methyl)-6-methylpyridazinone (I, M₂) was carried out in benzene, ethanol, phenol, and acetic acid at 60 and 80°C. The monomer reactivity ratios were found to vary with the reaction conditions. The linear correlationships were obtained by plotting the values of log r₁ against those of ^V C[dbnd]O and ^V C[dbnd]C of monomers determined in the solvents.     

Monomer-isomerization polymerization. XVIII. Monomer-isomerization copolymerizations of 4-phenyl-2-butene with 4-methyl-2-pentene and 3-heptene with Ziegler-Natta catalyst

4-Phenyl-2-butene (4Ph2B) undergoes monomer-isomerization copolymerization with 4-methyl-2-pentene (4M2P) and 2-and 3-heptene (2H and 3H) with TiCl₃–(C₂H₅)₃Al catalyst at 80°C to produce copolymer consisting exclusively of 1-olefin units. For comparison the copolymerization of 4-phenyl-1-butene (4Ph1B) with 4-methyl-1-pentene (4M1P) and 1-heptene (1H) was carried out under similar conditions. The composition of the copolymers obtained from these copolymerizations was determined from the ratios of optical densities D₁₃₈₀ and D₁₆₀₀ of infrared (IR) spectra of their thin films. The apparent monomer reactivity ratios for the monomer-isomerization copolymerization of 4Ph2B with 4M2P, 2H, and 3H in which the concentration of olefin monomer in the feed was used as internal olefin and those for the copolymerization of 4Ph1B with 4M1P and 1H were determined as follows: 4Ph2B(M₁)-4M2P(M₂); r₁ = 0.90, r₂ = 0.20, 4Ph1B(M₁)-4M1P (M₂); r₁ = 0.40, r₂ = 0.70, 4Ph2B(M₁)-2H(M₂); r₁, = 0.45, r₂ = 1.85, 4Ph2B(M₁)-3H(M₂); r₁ = 0.50, r₂ = 1.20, 4Ph1B(M₁)-1H(M₂); r₁ = 0.55, r₂ = 0.75. The difference in monomer reactivity ratios seemed to originate from the rate of isomerization from 2- or 3-olefins to 1-oletins in these monomer-isomerization copolymerizations.