Carbon dioxide sorption and transport in polycarbonate

The solubility, permeability, and diffusion time lag for carbon dioxide in polycarbonate are reported at 35°C for pressures ranging from 1 atm to 23 atm. The solubility data are very well described by the dual sorption mechanism model, Henry's law plus Langmuir adsorption, proposed for glassy polymers. Both the permeability and time lag decrease with increased CO₂ pressure. These observations are not consistent with the proposal that CO₂ sorbed by the Langmuir contribution is totally immobilized; however, all of the results are entirely consistent with an extension of this proposal which considers partial immobilization. The data have been quantitatively analyzed in terms of this partial immobilization model, and the results suggest for polycarbonate at 35°C that the CC₂ sorbed by the Langmuir portion of the isotherm behaves as if it has only about 10% of the mobility of the gas sorbed by the Henry's law part of the isotherm. The results have also been interpreted in terms of a concentration-dependent diffusion coefficient which is shown to be mathematically equivalent to the partial immobilization model. The latter model was also formulated in thermodynamic terms, whereby fugacity was used rather than pressure, and diffusion coefficients were defined in terms of chemical potential gradients rather than concentration, but the consequences of these changes proved to be minor and no better. The significance of these observations and their interpretation is discussed.     

Gas sorption and transport in miscible blends of tetramethyl bisphenol-A polycarbonate and polystyrene

The permeability coefficients for He, O₂, N₂, CH₄, and CO₂ in miscible blends of polystyrene (PS) and tetramethyl bisphenol-A polycarbonate (TMPC) at 35°C and 1 atm driving pressure are reported. Sorption isotherms for CO₂ and CH₄ are also presented. The isotherms were fitted to the dual sorption model. The Langmuir capacity factor was found to follow an earlier correlation based on unrelaxed volume. For each gas, the permeability was found to go through a minimum when plotted against blend composition. This behavior is primarily the result of the volume change on mixing observed for this system. The attractive interaction between TMPC and PS is relatively strong as indicated by density and solubility data. The value of the binary interaction parameter was found to be of the same magnitude as that for poly(phenylene oxide) (PPO)-polystyrene (PS) blends. Considering the similarity of structure between PPO and TMPC, it is concluded that similar phenyl-phenyl interactions and conformational changes on blending may prevail in TMPC/PS blends.     

Gas sorption and transport in polysulfone

The sorption and transport of CO₂, CH₄, Ar, and N₂ were measured in a melt-extruded film of polysulfone at 35°C. The results are interpreted in terms of the dual sorption and mobility models and compared to the structurally similar glassy polycarbonate. In addition, sorption measurements were made on specimens with various processing and treatment histories including porous membranes prepared by water coagulation of concentrated polysulfone solutions in DMF and THF. The sorption capacity for CO₂ varied considerably with the history of the specimen.     

Gas sorption and transport in substituted polycarbonates

The effects of molecular structure manipulation of polycarbonates on sorption and transport of various gases were studied using tetramethyl, tetrachloro, and tetrabromo substitutions onto the aromatic rings of bisphenol A polycarbonate. Solubility and permeability measurements were made at 35°C over the pressure range of 1–20 atm for a variety of gases, namely CO₂, CH₄, O₂, N₂, and He. A threefold to fourfold increase in permeability was caused by the tetramethyl substitution, whereas the tetrachloro and tetrabromo substitutions reduced the permeability relative to the tetramethyl substitution. Lower activation energies for transport were found for the tetramethyl polycarbonate relative to the unsubstituted polycarbonate. Permeability coefficients were factored into solubility and diffusion coefficients. Sorption levels increased for all substitutions, but among the substituted polymers the levels remain practically the same. Solubility data were analyzed in terms of the dual sorption model. The Henry's law solubility coefficients obtained from this analysis were found to be consistent with a predictive equation developed for rubbery polymers. The usual correlation for predicting the Langmuir sorption capacity of the model overestimates the values for the substituted polycarbonates, and a proposal for the cause of this is offered. Thermal expansion of these polymers was measured using dilatometry, and the results are used in the interpretation of the sorption data. Diffusion phenomena are explained by segmental mobility and free volume considerations. The effects of CO₂ exposure history on sorption and transport were also investigated.     

Gas sorption and transport in substituted polystyrenes

The effects of pendant groups on gas transport were investigated using a series of substituted polystyrenes. Permeability coefficients were measured at 35°C and 1 atm for He, N₂, O₂, CH₄, and CO₂, and diffusion coefficients were calculated from time lag data. The absolute permeabilities for the polystyrenes are correlated reasonably well using a free volume model. All pendant group substitutions resulted in a reduction of the mobility selectivity for CO₂/CH₄ separation relative to polystyrene, although there was very little effect on the O₂/N₂ selectivity. The effects of the various substituents were individually analyzed in terms of their size, rigidity, and polarity. The addition of a methyl group to the backbone significantly decreases transport, while attachment to the para ring position increases permeation. Bulky rigid groups, such as t-butyl, enhance permeation even more. Methoxy and acetoxy substitutions provided an excellent means of examining plasticization of polymers by CO₂, such as cellulose acetate, which contain these same moieties. The response of these polymers indicates that the degree of plasticization is related to the polarity and flexibility of the pendant group.     

Gas sorption and transport properties of bisphenol-I-polycarbonate

Gas sorption and transport characterization of a new polymer in the polycarbonate family, based on the bisphenol of 3,3,5-trimethylcyclohexane-1-one (BPI) is reported at 35°C. By comparison with properties of other known polycarbonates, the effects of inhibition of both packing and segmental motion due to the introduction of the bulky substituent in the backbone are elucidated. The T_g of the material was measured with differential scanning calorimeter (DSC) and was found to be unusually high for a polycarbonate (233°C). This indicates a successful inhibition of the large-scale segmental mobility of the polymer. Variable ¹³C NMR analysis indicated that rotation of one phenylene ring has an unusually high (ca. 10 kcal) energy barrier, whereas the other phenylene ring has a more typical rotation profile (barrier < 3 kcal). The density was measured and found to be low (1.107 g/cm³), indicating a high fractional free volume (FFV) for the polymer. Consistent with expectations, the introduction of the bulky-substituted cyclohexane group gave high permeabilities for the various gases tested (N₂, O₂, He, CH₄, CO₂) compared to most standard polycarbonates. On the other hand, the permselectivities were typical for standard polycarbonates. The solubility coefficients of all gases were rather high, as expected for a polymer with such an open structure. © 1994 John Wiley & Sons, Inc.     

Moisture uptake of a polycarbonate blend exposed to hygrothermal aging

As an extension of an earlier study on aging of a polycarbonate/acrylonitrile-butadiene-styrene (PC/ABS) blend, this paper has explored the roles of two competing phenomena, physical aging and moisture diffusion, during hygrothermal aging. Moisture absorption experiments at four different relative humidity conditions were compared with full immersion condition. Uptake curves show two different diffusion behaviour including Fickian moisture absorption and anomalous peak overshoot. The equilibrium moisture uptake in the polymer system, the coefficient of diffusion of moisture and the dual glass transitions were characterized. In general, the uptake behaviour could be explained using free volume expansion and contraction concepts that are associated with diffusion and structural recovery theories, respectively. However, using statistical methods, it was found that the relationship between the effects of aging temperature and relative humidity is both complex and interactive, with either diffusion or relaxation processes dominating depending on the extent of hygrothermal exposure.     

A rheological and morphological study of a copolyester liquid crystal/polypropylene blend system

The effects of composition and shear rate on the rheology and morphology of blends of LC–3000, a thermotropic liquid crystalline polymer consisting of 60/40 of hydroxybenzoic acid and poly(ethylene terephthalate), with polypropylene were studied. It was found that the rheological properties depend in a complex manner on composition and applied shear. Both positive and negative deviations from the log-additivity rule were observed at low shear rates. Significant viscosity reduction was measured when the dispersed phase was a nematic TLCP. The accompanying microstructural transitions were characterized a posteriori, and it was found that the state of dispersion of the TLCP phase also influences the viscosity reduction phenomenon. A nematic, fibrillar TLCP phase shows a viscosity reduction of the order of fourfold with respect to the viscosity of the matrix. Another important finding was that the stability of these fibers would not be expected from work on other non-TLCP-containing immiscible blends. This suggests that the unique rheology of the TLCP minor phase is relevant to the formation of stable fibers. © 1996 John Wiley & Sons, Inc.     

Combined sorption/transport of sodium dodecyl sulfate and hydrochloric acid in a blend of cellulose acetate butyrate with cellulose acetate hydrogen phthalate

The transport of hydrochloric acid (0.001-0.1 M) and sodium dodecyl sulfate (0.001-0.1 M) has been measured through a membrane consisting of a blend of cellulose acetate butyrate and cellulose acetate hydrogen phthalate. The cellulose derivative blend is suggested to suffer an alteration in the degree of hydrophobicity when in equilibrium with sodium dodecyl sulfate (SDS) through hemimicelle formation. An increase in surface hydrophobicity of the blend when in equilibrium with SDS solution was observed by fluorescence measurements using the vibronic bands of the probe pyrene, as well as by water desorption kinetics; a decrease of the effective diffusion coefficients from 1.2 × 10⁻¹¹ m² s⁻¹ in the absence of SDS to approximately 2 × 10⁻¹³ m² s⁻¹ in its presence was found. The value obtained for the mutual diffusion coefficient of HCl in the concentration range 0.001-0.1 M (D=4.2×10⁻¹⁴ m² s⁻¹) shows also that the membrane presents hydrophobic features. The flux of SDS in the blend membrane at different pH values shows two distinct permeation rates depending on the cmc. However, from the calculation of permeability coefficients at SDS concentrations below the cmc a clear decrease in P is found, whilst, at concentrations above the cmc the permeability coefficients are nearly constant, only showing a slightly increase. The diffusion coefficients of SDS in the blend increase over the whole SDS concentration range analysed and show an effective diffusion coefficient 2-3 orders of magnitude below the diffusion coefficients of SDS in aqueous solutions. This fact suggests that the only diffusing species are SDS unimers. The presence of HCl in the SDS bulk solution has the effect of increasing the permeability and diffusion coefficients. Mutual analysis of permeation and diffusion coefficients and sorption isotherms shows that, on decreasing the pH, the interactions between SDS and the polymer network decrease. This is also reflected in a clear decrease of the hydrophobic interactions between the diffusing and polymeric species, provoked by a decrease in the unimer-unimer association.     

Electron transport of holes in molecularly doped polycarbonate and its radiation-induced conductivity

The salient features of charge transport in a typical molecularly doped polymer (polycarbonate + 30 wt % DEH hydrazone) were studied by time-of-flight and nonsteady-state radiation-induced conductivity measurements. It was shows that the mobility of holes (major carriers) is due to dispersive transport in the temperature range 296–353 K covering the glass transition temperature at an observation time of up to a few seconds. The appearance of a plateau on the current transient, presumably manifesting the establishing of quasiequilibrium (Gaussian) transport, is the artifact of the time-of-flight technique when the charge carrier generation takes place at the sample surface. All of the obtained results can be satisfactorily rationalized in terms of the Rose-Fowler-Weisberg model with a uniform set of parameters of the model. Such an approach is compatible with the basic concepts of the radiation chemistry of condensed phase (the Onsager theory and the Langevin recombination mechanism), structural features of a disordered medium (transport zone, structural traps), and rotational diffusion of small molecules or their molecular groups in vitrified polymers.     

Gas transport properties of hyperbranched polyimide/hydroxy polyimide blend membranes

Gas transport properties of novel hyperbranched polyimide/hydroxy polyimide blends and their silica hybrid membranes were investigated. Gas permeability coefficients of the blend membranes showed positive deviation from a semilogarithmic additive rule. The enhanced gas permeability were resulted from the increase in free volume elements caused by the intermolecular interaction between terminal amine groups of the hyperbranched polyimide and hydroxyl groups of the hydroxy polyimide backbone. Additionally, CO₂/CH₄ separation ability of the blend membranes was markedly promoted by hybridization with silica. The remarkable CO₂/CH₄ separation behavior was considered to be due to characteristic distribution and interconnectivity of free volume elements created by the incorporation of silica. For the hyperbranched polyimide/hydroxy polyimide blend system, polymer blending and hybridization techniques synergistically provided the excellent CO₂/CH₄ separation ability.     

Hole transport in polystyrene and polycarbonate doped with polar dopants

Hole transport in PS and PC doped with low-molecular-mass dopants with dipole moments larger than 3D is investigated. Both near-surface and bulk charge-carrier generation techniques are used. There is good agreement between the experimentally measured values of hole mobility and the published data. It is shown that, for the investigated systems, the hole transport is nonequilibrium and is well described by the multiple-trapping model with the Gaussian trap distribution over energy. The presence of a flat plateau on the time-of-flight curves does not necessarily mean establishment of the quasi-equilibrium hole transport in the system.     

Gas sorption and transport in UV-irradiated polyarylate copolymers based on tetramethyl bisphenol-A and dihydroxybenzophenone

Gas sorption and transport properties at 35°C are reported for a series of ultraviolet irradiated polyarylates prepared from tetramethyl bisphenol-A (TMBPA), 4,4′-dihydroxybenzophenone (DHB), and 5-tertiary-butyl isophthalic acid dichloride (tBIA). UV irradiation induces crosslinking and photo-Fries rearrangements in these polymers. The gas permeability of the polyarylates decreases with UV irradiation due to reductions in the diffusion coefficient; however, the ideal selectivity for all gas pairs increases with UV irradiation. The effect of UV irradiation on the gas transport properties of the polyarylates is compared with that reported in the literature for similar polyimide materials. The polyimides show much greater improvement in selectivity than do the current polyarylate materials. The photo-Fries rearrangements limit the amount of crosslinking achievable in these polyarylate materials in spite of the fact that additional benzophenone units are formed.     

Orientation and mechanical properties of PBT and its blends with a liquid-crystalline copolyester

Blends of poly (butylene terephthalate) (PBT) and a liquid-crystalline copolyester (60 mol % poly(p-hydroxy benzoic acid)/40 mol % polyethylene terephthalate) (LCP) were prepared in the melt state. The investigation of mechanical properties indicated that, for the processing conditions used, neither the addition of up to 30 wt % LCP to PBT nor the cooling history affected significantly the tensile modulus E. For oriented specimens, a marked improvement of E was obtained for all the blends, and increased with the LCP content. This improvement was more marked for slowly cooled samples. X-ray diffraction was used to quantify the orientation of the crystalline PBT and liquid-crystalline LCP phases. It was shown that neither the thermal history nor the presence of up to 30 wt % LCP affected the orientation behavior of the PBT crystalline phase. For the LCP phase, measurements were not possible for concentrations lower than 10 wt %, and were more difficult and less precise than for PBT. Nevertheless, it was possible to show that a better orientation was obtained for the slowly cooled samples and for higher concentrations of LCP in the blends. This correlated with the enhancement of mechanical properties observed for the oriented samples.     

Water sorption and transport in a series of polysulfones

Water sorption and transport properties for a series of polysulfones are presented and interpreted in terms of the changes in the structure of the repeat unit compared to that of bisphenol A polysulfone. The differences between the sorption and diffusion of water and of permanent gases in these materials are also discussed. Water has the ability to interact with the polymer and with itself through hydrogen bonding in a way that permanent gases cannot. The equilibrium solubility of water in the polymer, unlike permanent gases, does not have a simple dependence on free volume but correlates more strongly with the frequency of hydrogen bonding sites on the polymer. Analysis of the sorption isotherms using the method of Zimm and Lundberg suggests that water molecules cluster in these polysulfones to various extents. For each polysulfone except polyethersulfone, the water diffusion coefficient decreases with increasing activity, which also suggests water clustering. For most of these materials, the water diffusion coefficient is larger than that of bisphenol A polysulfone and is directly related to the polymer free volume. Water permeability in these materials broadly correlates with the polymer free volume, but a favorable water-polymer interaction can be an overriding factor. © 1996 John Wiley & Sons, Inc.     

Sorption and transport mechanism of gases in polycarbonate membranes

The transport phenomena of oxygen and nitrogen across a pure polycarbonate (PC) and a cobalt(III) acetylactonate (Co(acac)₃) containing PC membrane was studied. Co(acac)₃ was added into a polycarbonate membrane to enhance its oxygen solubility. The oxygen sorption isotherms was measured. It was found that the oxygen solubility decreased sharply as pressure increased, especially at low pressure region. On the contrary, the oxygen permeability increased slightly with respect to pressure. Both the solution-diffusion model and traditional dual mobility model were unable to explain the inconsistent pressure dependency between solubility and permeability. Instead of adopting Langmuir-Henry sorption model, a modified dual mobility model which incorporates BET-type isotherm to describe oxygen sorption. The diffusivity of molecules moving at the first adsorbed layer was assumed to be different from those moving at higher layers. This modified dual mobility model satisfactorily described both the pressure dependency of oxygen solubility and permeability. It was also found that the increase of oxygen/nitrogen selectivity was not due to the elevation of oxygen to nitrogen solubility ratio but due to the mobility ratio of oxygen to nitrogen at the higher adsorption layers.     

Compatibility and fungal degradation of poly[(R)-3-hydroxybutyrate]/aliphatic copolyester blend

Poly[(R)-3-hydroxybutyrate] (PHB) was blended with an aliphatic copolyester, which was synthesized by the esterification of adipic acid, ethylene glycol, and lactic acid. The blend showed a single T_g, which varied systematically but convexly upwards with the composition. The growth rate of PHB spherulites, the crystallization temperature, and the equilibrium melting temperature of the blend were decreased as the amount of the copolyester was increased. Therefore, the blend system was determined to be compatible. However, the degree of crystallinity, and the enthalpies of crystallization and fusion of PHB in the blend remained almost constant, regardless of the compositional change, although the crystallization rate was decreased upon blending. No chemical change such as transesterification was observed as a result of the blending, yet there was a slight change in the crystalline morphology of PHB. The rate of fungal degradation was lowered with an increase in the copolyester content of the blend. © 1996 John Wiley & Sons, Inc.     

Crystallizing crazes: The probable source of solvent stress cracking resistance in a polyester/polycarbonate blend

The addition of a miscible phthalate polyester to BPA polycarbonate results in a remarkable improvement in stress cracking resistance in strong swelling agents. Comparative measurements of solvent craze initiation resistance, craze strengths, degrees of swelling, and crystallization behavior have been made. The results indicate that the improvement in cracking resistance probably results from stabilization of the craze fibrils by crystallization of the polyester before and/or during fibril formation.