Studies on heat-resistant poly(metal phthalocyanine)-imide copolymers

Several new poly(metal phthalocyanine)imide copolymers have been prepared using 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BPTDA), metal(11) 4,4′,4″,4″′-phthalocyanine tetraamines (MPTA), p-phenylenediamine, 4,4′-methylenedianiline, and 9,9-bis(4-aminophenyl)-fluorene (BAF). The attractive feature of these polymers is their high thermooxidative and thermal stability. The polymer decomposition temperatures of all the imide copolymers are greater than 500°C in air and N atomspheres. Another noteworthy property is their high char yield: 60–78% at 800°C in a N₂ atmosphere. Variation of the metal phthalocyanine concentration has a remarkable effect on the thermal stability and degree of polymerization. The most preferred molar proportion of the reagents MPTA, diamine, and BTDA is 1.25:7.5:10. These polymers may be useful in the preparation of heat-resistant films and fibers.     

Synthesis and Properties of Aromatic Poly(Ether Sulfone)s and Poly(Etherketone)s Containing Naphthalene or Quinoline Units,and Methyl-Substituted Biphenyl-4,4′-Diols

Abstract

A series of poly(ether sulfone)s and poly(ether ketone)s were synthesized from combinations of 1,5- and 2,6-bis(4-fluorosulfonyl)naphthalene, 2,6-bis(4-fluorobenzoyl)naphthalene, and 2,6-bis(4-fluorobenzoyl)quinoline with 3,3′,5,5′-tetramethylbiphenyl-4,4′-diol and 2,2′,3,3′,5,5′-hexamethylbiphenyl-4,4′-diol. The polycondensations proceeded quantitatively in diphenylsulfone in the presence of anhydrous potassium carbonate to afford polymers with inherent viscosities between 0.40 and 1.28 dL/g measured in N-methyl-2-pyrrolidone or concentrated sulfuric acid. The tetramethyl- and hexamethyl-substituted aromatic polyethers exhibited good thermal stability, did not decompose below 330°C in both air and nitrogen atmospheres, and had higher glass transition temperatures than the corresponding unsubstituted polymers. The methylsubstituted poly(ether sulfone)s and poly(ether ketone)s showed good solubility in such common organic solvents as N-methyl-2-pyrrolidone, N,N-dimethylacetamide, tetrahydrofuran, chloroform, and 1,4-dioxane.     

Aromatic polybenzoxazoles containing ether–sulfone linkages

A series of poly(o‐hydroxy amide)s having both ether and sulfone linkages in the main chain were synthesized via the low‐temperature solution polycondensation of 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoyl chloride and 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoyl chloride with three bis(o‐aminophenol)s including 4,4′‐diamino‐3,3′‐dihydroxybiphenyl, 3,3′‐diamino‐4,4′‐dihydroxybiphenyl, and 2,2‐bis(3‐diamino‐4‐hydroxyphenyl)hexafluoropropane. Subsequent thermal cyclodehydration of the poly(o‐hydroxy amide)s afforded polyethersulfone benzoxazoles. Most of the poly(o‐hydroxy amide)s were soluble in polar organic solvents such as N‐methyl‐2‐pyrrolidone; however, the polybenzoxazoles without the hexafluoroisopropylidene group were organic‐insoluble. The polybenzoxazoles exhibited glass‐transition temperatures (T_g) in the range of 219–282 °C by DSC and softening temperatures (T_s) of 242–320 °C by thermomechanical analysis. Thermogravimetric analyses indicated that most polybenzoxazoles were stable up to 450 °C in air or nitrogen. The 10% weight loss temperatures were recorded in the ranges of 474–593 °C in air and 478–643 °C in nitrogen. The methyl‐substituted polybenzoxazoles had higher T_g's but lower T_s's and initial decomposition temperatures compared with the corresponding unsubstituted polybenzoxazoles. For a comparative purpose, the synthesis and characterization of a series of sulfonyl polybenzoxazoles without the ether group that derived from 4,4′‐sulfonyldibenzoyl chloride and bis(o‐aminophenol)s were also reported. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2262–2270, 2001     

New organosoluble polyimides with low dielectric constants derived from bis[4-(2-trifluoromethyl-4-aminophenoxy)phenyl] diphenylmethylene

A new kink diamine with trifluoromethyl group on either side, bis[4-(2-trifluoromethyl-4-aminophenoxy)phenyl]diphenylmethane (BTFAPDM) , was reacted with various aromatic dianhydrides to prepare polyimides via poly (amic acid) precursors followed by thermal or chemical imidization. Polyimides were prepared using 3,3′, 4,4′-biphenyltetracarboxylic dianhydride(1), 4,4′-oxydiphthalic anhydride(2), 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (3), 4,4′-sulfonyldiphthalic anhydride(4), and 4,4′-hexafluoroisopropylidene-diphathalic anhydride(5). The fluoro-polyimides exhibited low dielectric constants between 2.46 and 2.98, light color, and excellent high solubility. They exhibited glass transition temperatures between 227 and 253°C, and possessed a coefficient of thermal expansion (CTE) of 60-88 ppm/°C. Polymers PI-2, PI-3, PI-4, PI-5 showed excellent solubility in the organic solvents: N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), pyridkie and tetrahydrofuran (THF). Inherent viscosity of the polyimides were found to range between 0.58 and 0.72 dLg-1. Thermogravimetric analysis of the polyimides revealed a high thermal stability decomposition temperature in excess of 500°C in nitrogen. Temperature at 10 % weight loss was found to be in the range 506-563°C and 498-557°C in nitrogen and air, respectively. The polyimide films had a tensile strength in the range 75-87 MPa; tensile modulus, 1.5-2.2 GPa; and elongation at break, 6-7%.     

Polyimide containing internal acetylene units linked para to the aromatic ring

4,4′-Diaminodiphenylacetylene (p-intA) was reacted with 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA), 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) and pyromellitic dianhydride (PMDA) in N-methyl-2-pyrrolidone (NMP) to give poly(amic acid) solution of moderate to high viscosity. Thermal imidization gave polyimide having acetylene units that are linked para to the aromatic connecting unit. Polyimide having acetylene units that are linked meta to the aromatic connecting unit also was prepared utilizing 3,3′-diaminodiphenylacetylene (m-intA) for comparison. The crosslinking behavior of the acetylene units was observed with DSC. Exotherm due to the crosslinking of the para-linked acetylene units appeared at ca. 340 to 380°C depending on the structure of polyimide, whereas meta-linked acetylene units appeared at lower temperature as 340–350°C. After thermal treatment at high temperature such as 350 or 400°C, the amount of the exotherm became smaller and finally disappeared on DSC, confirming the progress of crosslinking. Dynamic mechanical properties of the polyimide films show that glass transition temperature increased with higher heat treatment, also confirming the progress of crosslinking. Tensile properties of the polyimide films showed that rigid polyimide films consisting of p-intA with BPDA or PMDA have considerably higher modulus than those consisting of m-intA. Cold-drawing of the poly(amic acid) followed by imidization gave much higher modulus in the case of rigid polyimide. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2395–2402, 1997     

Novel poly(fluorinated imide)s containing naphthalene pendant group: synthesis and characterization

A new fluorinated diamine monomer containing naphthalene pendant group, bis(4-amino-3,5-difluorophenyl)naphthylmethane (monomer 1), was synthesized from 1-naphthaldehyde and 2,6-difluoroaniline with trifluoromethanesulfonic acid at reflux. The novel poly(fluorinated imide)s (PFIs) were prepared via one-step polycondensation by monomer 1 and three aromatic dianhydrides including 4,4′-oxydiphthalic dianhydride, 3,3′,4,4′-benzophenonetetracarboxylic dianhydride, and 3,3′,4,4′-biphenyltetracarboxylic dianhydride in m-cresol, respectively. The obtained PFIs could be dissolved in a variety of organic solvents such as N-methyl-2-pyrrolidinone, N,N-dimetahylacetamide (DMAC), N,N-dimethylformamide, chloroform, and tetrahydrofuran at room temperature. The highest solubility of PFIs could even reach to 250 mg/mL in chloroform. The PFIs could be easily processed into flexible and tough films by casting onto glass from DMAC solution. The PFI films had a tensile strength, elongation at break, and tensile modulus in the range of 84–102 MPa, 8.7–12.8%, and 2.2–2.8 GPa, respectively. These polymers also showed excellent thermal stability with glass transition temperatures in the range of 326–352 °C, 10% weight loss temperatures in the range of 538–574 °C, and the weight residue more than 57% at 800 °C in nitrogen. Moreover, as for the optical properties, these PFIs exhibited a strong optical absorption in the ultraviolet region (290–370 nm) and photoluminescence in dilute chloroform solution or solid state.     

Synthesis and properties of aromatic poly (ether sulfone)s and poly (ether ketone)s based on methyl-substituted biphenyl-4,4′-diols

Novel methyl-substituted aromatic poly (ether sulfone)s and poly (ether ketone)s were synthesized from combinations of 3,3′,5,5′-tetramethylbipheny-4,4′-diol and 2,2′,3,3′,5,5′-hexamethylbiphenyl-4,4′-diol, and 4,4′-dichlorodiphenyl sulfone and 4,4′-difluorobenzo-phenone by nucleophilic aromatic substitution polycondensation. The polycondensations proceeded quantitatively in a N-methyl-2-pyrrolidone-toluene solvent system in the presence of anhydrous potassium carbonate to afford the polymers with inherent viscosities between 0.86 and 1.55 dL/g. The methyl-substituted poly (ether sulfone)s and poly (ether ketone)s showed good solubility in common organic solvents such as chloroform, tetrahydrofuran, pyridine, m-cresol, and N,N-dimethylacetamide. The tetramethyl- and hexamethyl-substituted aromatic polyethers had higher glass transition temperatures than the corresponding unsubstituted polymers, and did not decompose below 350°C in both air and nitrogen atmospheres. The films of the methyl-substituted poly (ether ketone)s became insoluble in chloroform by the irradiation of ultraviolet light, indicating the occurrence of photochemical crosslinking reactions. © 1994 John Wiley & Sons, Inc.     

Polyimidines. XI. Polyimidines from 3,3′,4,4′-benzophenonetetracarboxylic dianhydride and 4,4′-(hexafluoroisopropylidene) diphthalic anhydride

Two new bis(benzylidenephthalide)monomers were synthesized by melt condensation of phenylacetic acid with 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) and with 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6FDA). A mixture of three isomers for each monomer was obtained and polymerized with diamines to produce new polyimidines. Polymerizations were conducted with m-xylylenediamine (MXDA) or 4,4′-oxydianiline (ODA) in quantitative yields for the undehydrated intermediate. Inherent viscosities ranged from 0.17 to 0.35 dL/g in N,N-dimethylformamide (DMF) or N-methyl-2-pyrrolidone (NMP). These intermediate poly(hydroxylactams) were thermally dehydrated to polyimidines which exhibited a 10% weight loss, as high as 546°C in nitrogen. Inherent viscosities of the dehydrated (cured) polyimidines ranged from 0.14 to 0.20 dL/g in NMP. Brittle films could be cast from NMP solutions.     

Synthesis and comparative study on polyetherimides from isomeric 4,4′-isopropylidenediphenoxy bis(phthalic anhydride)s

Two isomers of commercial 4,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (4,4′-BPADA), that is, 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,4′-BPADA) and 3,3′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,3′-BPADA), were synthesized through aromatic nucleophilic substitution from nitrophthalonitrile and bisphenol A. 3,4′-BPADA was first synthesized from two intermediates, that is, 3-(4-[4-hydroxyphenylisopropylidene] phenoxy) phthalonitrile (3-BPADN) and 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalonitrile) (3,4′-BPATN). The corresponding three series of polyetherimides (PEIs) were prepared with two representative aromatic diamines (4,4′-oxydianiline and m-phenylenediamine (m-PDA)) via two-step procedure and chemical imidization. Isomeric polyimides showed T_gs from 206 to 256°C in nitrogen and T_d5%s from 488 to 511°C in argon, good mechanical properties (tensile moduli of 2.3–3.3 GPa, tensile strengths of 70–96 MPa, and elongations at break of 3.2%–5.1%), and good solubility. With the introduction of 3-substituted phthalimide unit, PEIs displayed higher T_g values, lower strengths and elongations, better solubility and larger d-spacings. The rheological properties of thermoplastic polyimide resins based on the BPADA isomers were investigated, which showed that polyetherimide PEI-3b derived from 3,3′-BPADA and m-PDA had the lowest melt viscosity among the isomers, indicating that the melt processibility had been greatly improved.     

Thermotropic liquid crystalline polymer. III. Synthesis and properties of poly(amide-azomethine-ester)

A series of novel dialdehydes as new monomers, 4,4′-diformyl-α,ω-diphencarbonylalkane, 4,4′-diformyl-3,3′-methoxy-α,ω-diphencarbonylalkane, and 4,4′-diformyl-3,3′-ethoxy-α,ω-diphencarbonylalkane, was prepared from aliphatic diacid chloride with p-hydroxybenzaldehyde, vanillin, and 3-ethoxy-4-hydroxybenzaldehyde, respectively. A series of poly(amide-azomethine-ester)s was prepared by condensation of 4,4′-diaminoanilide with 4,4′-diformyl-α,ω-α,ω-diphencarbonylalkane, 4,4′-diformyl-3,3′-methoxy-α,ω-diphencarbonylalkane, and 4,4′-diformyl-3,3′-ethoxy-α,ω-diphencarbonylalkane, respectively. Their thermotropic liquid crystalline properties were examined by DSC microscope observations. In most cases, the mesophase extends up to ca. 288–380°C, where thermal decomposition prevents further observation.     

Synthesis,liquid crystallinity,and mechanical properties of thermotropic polyquinolines

Thermotropic liquid-crystalline polyquinolines with high molecular weights, i.e., poly[2,2′-(α,ω-dioxyphenylene (or -dioxybiphenylene) alkane)-6,6′-(4,4′-dioxybiphenyl)-bis(4-phenylquinoline)]s (P-H-B1Mns or P-H-B2Mns), were synthesized by polycondensation of 4,4′-bis(4-amino-3-benzoylphenoxy)biphenyl and α,ω-bis(4-acetophenoxy (or -acetobiphenoxy))alkanes. For P-H-B1Mn series, the T_m and T_i were in the range of 129–230°C and 156–254°C, respectively, while for the P-H-B2Mn series, those were 182–275°C and 217–309°C, respectively. The introduction of both the dioxybiphenylene group and an alkylene spacer induced thermotropic liquid crystallinity in the polyquinoline, although the introduction of the alkylene spacer alone did not induce it. In addition, polyquinolines substituted with methyl, methoxy, and chloro groups exhibited larger mesophase temperature ranges as well as higher T_ms and T_is than the unsubstituted ones. Tensile strengths of these thermotropic polyquinolines were considerably high in the range of 770 to 1170 kgf/cm². © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 749–759, 1998     

Synthesis and characterization of optically active poly(amide-imide)s based on [N,N′-(4,4′-carbonyldiphtaloyl)-bis-lamino diacid]s and 1,5-bis(4-aminophenyl)penta-1,4-dien-3-one

Six dicarboxylic acids 3a-3f were synthesized by the reaction of 3,3’,4,4’-benzophenonetetracarboxylic dianhydride 1 with L-aminoacids 2a-2f in a solution of glacial acetic acid/pyridine(Py) at refluxing temperature.Then six new poly(amide-imide)s PAIs were synthesized from the direct polycondensation reaction of[N,N’-(4,4’- carbonyldiphtaloyl)-bis-L-amino diacid]s with 1,5-bis(4-aminophenyl)penta-1,4-dien-3-one(APPD).The polymerization reactions produced a series of new optically active PAIs with high yield and good inherent viscosity.Also these PAIs are optically active and soluble in various organic solvents.These resulting new polymers can be used in column chromatography for the separation of enantiomeric mixtures.The resulted polymers were fully characterized by means of FTIR and ~1H-NMR spectroscopy,elemental analyses,inherent viscosity measurements,solubility tests and thermogravimetric analysis(TGA).     

Synthesis and characterization of aromatic polyimide and polyamide-imide from 2,5-bis(4-isocyanatophenyl)-3,4-diphenylthiophene and aromatic tetra- and tricarboxylic acids

Soluble polyimide having an inherent viscosity up to 1.4 dL/g was synthesized by the high-temperature solution polycondensation of 2,5-bis(4-isocyanatophenyl)-3,4-diphenylthiophene with 3,3′,4,4′-benzophenonetetracarboxylic dianhydride. The polycondensation of the tetraphenylthiophene diisocyanate with trimellitic anhydride afforded polyamide-imide with an inherent viscosity up to 0.9 dL/g. These polymers showed limited solubility in organic solvents and had glass transition temperatures around 320°C.     

Polyimides containing carbonyl and ether connecting groups. II

In a continuation of our effort on polyimides containing carbonyl and ether connecting groups between aromatic rings, several new polyimides were prepared and characterized. A few of these polymers were semi-crystalline. Glass transition temperatures ranged from 164 to 258°C and crystalline melt temperatures were observed between 350 and 424°C. The semi-crystalline polyimide from the reaction of 3,3′,4,4′-benzophenonetetracarboxylic dianhydride and 1,3-bis(4-aminophenoxy-4′-benzoyl)benzene provided transparent orange films with excellent tensile properties, exceptional resistance to solvents and strong base, and high thermooxidative stability. In addition, this polyimide provided excellent adhesive strength for joining titanium (6A1–4V) to titanium.     

New poly(amide-imide)s syntheses. XVII. Preparation and properties of poly(amide-imide)s derived from 3,3-Bis[4-(4-aminophenoxy)phenyl]phthalimidine and various bis(trimellitimide)s

A series of novel bis(phenoxy)phthalimidine-containing poly(amide-imide)s III were synthesized by the direct polycondensation of 3,3-bis[4-(4-aminophenoxy)phenyl]phthalimidine (BAPP) with various aromatic bis(trimellitimide)s in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. Poly(amide-imide)s III , having inherent viscosities up to 1.36 dL/g, were obtained in quantitative yields. All resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. All the soluble poly(amide-imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range of 267–322°C and the 10% weight loss temperatures were above 490°C in nitrogen. Some properties of poly(amide-imide)s III were compared with those of the corresponding isomeric poly(amide-imide)s III′ prepared from 3,3-[4-(4-trimellitimidophenoxy)phenyl]-phthalimidine and various aromatic diamines. © 1996 John Wiley & Sons, Inc.     

Poly(ethylene terephthalate) reinforced by N,N′‐diphenyl biphenyl‐3,3′,4,4′‐tetracarboxydiimide moieties

Starting with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and methyl aminobenzoate, we synthesized a novel rodlike imide‐containing monomer, N,N′‐bis[p‐(methoxy carbonyl) phenyl]‐biphenyl‐3,3′,4,4′‐tetracarboxydiimide (BMBI). The polycondensation of BMBI with dimethyl terephthalate and ethylene glycol yielded a series of copoly(ester imide)s based on the BMBI‐modified poly(ethylene terephthalate) (PET) backbone. Compared with PET, these BMBI‐modified polyesters had higher glass‐transition temperatures and higher stiffness and strength. In particular, the poly(ethylene terephthalate imide) PETI‐5, which contained 5 mol % of the imide moieties, had a glass‐transition temperature of 89.9 °C (11 °C higher than the glass‐transition temperature of PET), a tensile modulus of 869.4 MPa (20.2 % higher than that of PET), and a tensile strength of 80.8 MPa (38.8 % higher than that of PET). Therefore, a significant reinforcing effect was observed in these imide‐modified polyesters, and a new approach to higher property polyesters was suggested. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 852–863, 2002; DOI 10.1002/pola.10169     

Aromatic polyamides and polyimides derived from 3,3′-diaminobiphenyl: Synthesis,characterization, and molecular simulation study

In this article a new synthesis of 3,3′-diaminobiphenyl (3,3′-DABP) is described, along with the preparation and characterization of polyamides and polyimides based on it. Reactivity of this monomer was calculated by a molecular simulation study, using ab initio quantum-mechanical methods. Terephthaloyl and isophthaloyl chloride were used for the synthesis of polyamides, while 3,3′,4,4′-biphenylenetetracarboxylic acid dianhydride and 4,4′-(hexafluoroisopropylidene) diphthalic anhydride were used for the synthesis of polyimides. Medium to high molecular weight polymers were attained, with inherent viscosities near or higher than 1.0 dL/g, the solubility of the 3,3′-DABP polymers was much better than that of the homologous polymers from benzidine (4,4′-DABP), the glass-transition temperatures were lower, by about 40°C, and the thermal resistance, as measured by thermogravimetry, was virtually the same. Amorphous films, made from cast polymer solutions, showed excellent mechanical properties, comparable to conventional aromatic polyamides and polyimides. Theoretical calculations demonstrated that the radius of giration, end-to-end distance and density of poly(3,3′-DABP-isophthalamide) were lower than those of poly(4,4′-DABP-isophthalamide), as a consequence of the chain folding induced in the backbone by the m-substitution in 3,3′-DABP. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4646–4655, 1999     

Polyaddition reactions of bisethyleneureas and 1,1,3,3-diethyleneurea with polymethylene dimercaptans in LiCl-dimethylformamide

Polyaddition reactions of 1,1′-tetramethylenebis(3,3-ethyleneurea) (IIa), 1,1′-octamethylenebis(3,3-ethyleneurea) (IIb), 1,1′-p-phenylenebis(3,3-ethyleneurea) (IIc), 1,1′-(4,4′-diphenylmethane)bis(3,3-ethyleneurea) (IId) and 1,1,3,3-diethyleneurea (III) with polymethylene dimercaptans were investigated. 1,1′-Polymethylenebis(3,3-ethyleneureas) and polymethylene dimercaptans successfully reacted at 80–95°C. in the presence of triethylamine to give poly(urea sulfides) with intrinsic viscosities up to 1.1 in about 90% yield when dimethylformamide, dimethylacetamide, or N-methyl-2-pyrrolidone containing lithium chloride as a solvent were used. The other ethyleneureas, however, failed to give high molecular weight polymers.     

Preparation of Poly(amic acid) and Polyimide via Microwave-Assisted Polycondensation of Aromatic Dianhydrides and Diamines

Summary: A copolycondesation-type poly (amic acid) (PAA) was synthesized using pyromellitic dianhydride (PMDA) and 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) as dianhydride monomers, and 4,4′-oxydianiline (ODA) as a diamine monomer under microwave irradiation in dimethylformamide (DMF). PAA was then converted into a polyimide (PI) by an imidization. The structure and performance of the polymer were characterized by Fourier-transform infrared (FT-IR) spectroscopy, Proton nuclear magnetic resonance (¹H NMR) spectrometry, viscosity, X-ray diffraction (XRD), and thermogravimetric (TG) analyses. The results showed that under microwave irradiation, the intrinsic viscosity and the yield of PAA were increases, and the reaction time was shortened. The FT-IR spectra of the polymer revealed characteristic peaks for PI around 1778^– and 1723 cm^–1. TG curves indicated that the obtained PI began to lose weight at 535 °C, and its 10% thermal decomposition temperature under N₂ was 587 °C.     

Reactive lyotropic polyimide oligomers

Amine-terminated and maleimide-terminated oligomers of molecular weight 1200–1800 based on 2,2′-bis(trifluoromethyl)-4,4′-diaminobiphenyl and 3,3′,4,4′-biphenylenetetracarboxylic dianhydride were synthesized and characterized for lyotropic liquid crystalline behavior. Several different synthetic procedures were evaluated and a one-step procedure in m-cresol was found to be the most effective for producing fully imidized materials. Lyotropic behavior was observed only for the as-prepared solutions in m-cresol and in dilutions of this solution. Oligomer thermal stability was excellent, onsets of decomposition were in excess of 550°C. © 1996 John Wiley & Sons, Inc.