H2-induced CO adsorption and dissociation over Co/Al2O3 catalyst

The activation of adsorbed CO is an important step in CO hydrogenation. The results from TPSR of pre-adsorbed CO with H2 and syngas suggested that the presence of H2 increased the amount of CO adsorption and accelerated CO dissociation. The H2 was adsorbed first, and activated to form H＊ over metal sites, then reacted with carbonaceous species. The oxygen species for CO2 formation in the presence of hydrogen was mostly OH^＊, which reacted with adsorbed CO subsequently via CO^＊＋OH^＊ → CO2^＊＋H^＊; however, the direct CO dissociation was not excluded in CO hydrogenation. The dissociation of C-O bond in the presence of H2 proceeded by a concerted mechanism, which assisted the Boudourd reaction of adsorbed CO on the surface via CO^＊＋2H^＊ → CH^＊＋OH^＊. The formation of the surface species （CH） from adsorbed CO proceeded as indicated with the participation of surface hydrogen, was favored in the initial step of the Fischer-Tropsch synthesis.     

H2-induced CO adsorption and dissociation over Co/Al2O3 catalyst

The activation of adsorbed CO is an important step in CO hydrogenation. The results from TPSR of pre-adsorbed CO with H2 and syngas suggested that the presence of H2 increased the amount of CO adsorption and accelerated CO dissocia-tion. The H2 was adsorbed first, and activated to form H* over metal sites, then reacted with carbonaceous species. The oxygen species for CO2 formation in the presence of hydrogen was mostly OH*, which reacted with adsorbed CO subsequently via CO*+OH* → CO2*+H*; however, the direct CO dissociation was not excluded in CO hydrogenation. The dissociation of C-O bond in the presence of H2 proceeded by a concerted mechanism, which assisted the Boudourd reaction of adsorbed CO onthe surface via CO*+2H* → CH*+OH*. The formation of the surface species (CH) from adsorbed CO proceeded as indicated with the participation of surface hydrogen, was favored in the initial step of the Fischer-Tropsch synthesis.     

IR spectral study of the effect of the reaction medium on the state of cobalt in a 10% Co/Al2O3 catalyst for aliphatic hydrocarbons from CO and H2

Diffuse scattering IR spectroscopy was used to study the 10% Co/Al₂O₃ catalyst for the synthesis of aliphatic hydrocarbons from CO and H₂. Ionic and metallic cobalt forms were identified in the IR spectroscopy. The adsorption of CO on these forms is accompanied by the appearance of linear and bridged complexes. After prolonged treatment of the catalyst by a CO + 2H₂ mixture, the ions and surface of metallic cobalt remain available for the adsorption of CO. Modification of the surface of metallic cobalt occurs upon the action of the reaction medium. This modification is seen in a bathochromic displacement of the IR bands for the adsorbed and linear CO forms. This displacement is accompanied by a reduction in the strength of the metal-carbon bond in the Co^o-CO complex.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 11, pp. 2640–2643, November, 1990.     

Cu/ZnO/Al2O3催化剂的共沉淀-蒸氨法制备及其对二氧化碳加氢制甲醇的研究

分别以碳酸铵为沉淀剂采用共沉淀-蒸氨法(CAE)和以碳酸铵(CCA)、碳酸钠(CCS)为沉淀剂采用常规共沉淀法制备了三种Cu/ZnO/Al2O3催化剂,并运用XRD,BET,TPR和N2O滴定技术对催化剂进行了表征.结果表明:采用共沉淀-蒸氨法制备的催化剂具有较小的颗粒尺寸、较大的Cu(0)比表面积;以碳酸铵为沉淀剂常...     

Effects of pretreatment and reduction on the Co/Al2O3 catalyst for CO hydrogenation

The purpose of this study was to investigate the effect of preadsorbed CO at different temperatures, calcination temperatures, the combined influence of reduction temperature and time, and pretreatment using hydrogen or syngas as reduction agents on the F-T synthesis （FTS） activity and selectivity of Co/Al2O3 catalyst. The reactivity of the carbon species at higher preadsorption temperature with H2 in TPSR decreased, whereas the carbon-containing species showed higher reactivity over Co/Al2O3 catalyst with low calcination temperature. This agreed well with the order of catalytic activity for F-T synthesis on this catalyst. The catalytic activity of the catalyst varied with reduction temperature and time remarkably. CODEX optimization gave an optimum reduction temperature of 756 K and reduction time of 6.2 h and estimated C5＋ yield perfectly. The pretreatment of Co/Al2O3 catalyst with different reduction agents （hydrogen or syngas） showed important influences on the catalytic performance. A high CO conversion and C5＋ yield were obtained on the catalyst reduced by hydrogen, whereas methane selectivity on the catalyst reduced by syngas was much higher than that on the catalyst reduced by hydrogen.     

Rh2CO2/Al2O3上H2吸附及CO和H2共吸附

CO加氢反应机理一直是许多化学工作者感兴趣的课题．Rh催化剂因其优良的性能而被用于 CO加氢机理研     

Coking-resistant Ni-ZrO2/Al2O3 catalyst for CO methanation

Highly coke-resisting Zr O2-decorated Ni/Al2O3 catalysts for CO methanation were prepared by a two-step process. The support was first loaded with Ni O by impregnating method and then modified with Zr O2 by deposition-precipitation method(IM-DP). Nitrogen adsorptiondesorption, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, H2 temperatureprogrammed reduction and desorption, NH3temperature-programmed desorption, and zeta potential analysis were employed to characterize the samples. The results revealed that, compared with the catalysts with the same composition prepared by co-impregnation(CI) and sequential impregnation(SI) methods, the Ni/Al2O3 catalyst prepared by IM-DP showed much enhanced catalytic performance for syngas methanation under the condition of atmospheric pressure and a high weight hourly space velocity of 120000 m L g-1 h-1. In a 80 h life time test under the condition of 300–600°C and 3.0 MPa, this catalyst showed high stability and resistance to coking, and the amount of deposited carbon was only 0.4 wt%. On the contrary, the deposited carbon over the catalyst without Zr O2 reached 1.5 wt% after a 60 h life time test. The improved catalytic performance was attributed to the selective deposition of Zr O2 nanoparticles on the surface of Ni O rather than Al2O3, which could be well controlled via changing the electrostatic interaction in the DP procedure. This unique structure could enhance the dissociation of CO2 and generate surface oxygen intermediates, thus preventing carbon deposition on the Ni particles in syngas methanation.     

CO Hydrogenation by K-Promoted Coprecipitated Co/Al2O3

Effect of K promotion on the CO hydrogenation activity and selectivity of coprecipitated Co/Al₂O₃ has been studied. K addition is found to lower total activity while enhancing C₂-C₄ olefins selectivity; kinetic data indicate that the reaction mechanism is not affected.     

Effect of synthesis solution pH of Co/γ-Al_2O_3 catalyst on its catalytic properties for methane conversion to syngas

The cobalt nanoparticles over γ-Al_2O_3 support were prepared via chemical reduction of CoCl_2·6H_2O using NaBH_4 with various values of pH in the range of 11. 92-13. 80. Synthesized catalysts were studied through X-ray diffraction( XRD),N_2 adsorption/desorption( BET),H_2-temperature programmed reduction( H_2-TPR),H_2-chemisorption,O_2 pulse titration and temperature programmed oxidation( TPO) methods. Obtained results exhibited the synthesis solution pH showed a significant influence on the activity and selectivity in partial oxidation of methane reaction. The methane conversion,CO selectivity and H_2 yield were enhanced by increasing of the synthesis solution pH. Compared to other catalysts,the catalyst that synthesized at pH of 13.80,showed a superior ability in syngas production with a H_2/CO ratio of near 2 and also a proper stability against deactivation during the partial oxidation of methane.     

Pd-Cu-Clx/Al2O3催化剂对CO氧化的稳定性

CO催化氧化广泛应用于空气净化、机动车尾气治理和CO气体传感器中.在CO氧化催化剂设计与制备过程中,催化剂与使用环境密切相关.例如工业和机动车尾气净化需要在高温(200–600°C)下进行,而对于半密闭空间(隧道或者地下停车场)空气净化需要在室温和高相对湿度下进行.频繁冷启动导致半密闭空间CO浓度累积而超过排放控制标准,因此制备室温、高相对湿度下CO氧化催化剂是面临的重要问题之一.负载型Wacker催化剂对于CO低温催化氧化的研究一直受到广泛关注.环境中少量水的存在会促进负载型Wacker催化剂对CO的低温氧化性能,但随着水沉积量的增加,活性位点将被覆盖,并且Pd和Cu活性组分之间的紧密结构被破坏,从而导致催化剂的失活,即催化剂的稳定性变差.因此,为了提高催化剂在高相对湿度下的稳定性,利用二乙氧基二甲基硅烷对Al2O3载体进行硅烷化处理,以增加载体的疏水性,考察载体疏水改性对CO低温氧化过程中催化剂稳定性的影响.催化剂的稳定性测试结果表明,在0°C,100%相对湿度条件下,未改性催化剂在约20 h内CO转化率由81%下降到50%;载体硅烷化后制备的催化剂在反应进行150 h后,CO转化率仍保持在78%,即反应活性未见降低.由此表明催化剂载体经有机硅烷改性后,可显著增强催化剂在低温、高相对湿度下的稳定性.N2吸附/脱附和水吸附实验结果表明,载体硅烷化改性并未对催化剂的比表面积产生影响,但显著降低了催化剂上水沉积速度和沉积量,未改性催化剂的初始吸水速度是改性后催化剂的4倍,但改性后催化剂的饱和吸水率仅占未改性催化剂的1/3.X射线衍射结果表明,载体预处理后活性物种Cu2(OH)3Cl晶粒尺寸有所增加.氢气程序升温还原、X射线光电子能谱结果表明,载体硅烷化预处理改善了催化剂中Cu和Pd物种的化学分布及接触状态,增加了与Pd物种紧密接触的Cu物种的量,从而促进了Cu物种的还原.与此同时,载体硅烷化显著降低了催化剂表面Cl离子的浓度,从而影响到对CO吸附.为了进一步研究水与催化剂稳定性之间的关系,采用原位红外漫反射(In situ DRIFT)对催化剂进行表征.负载型Wacker催化剂对CO氧化反应机理为:Pd是CO氧化反应的活性中心,通过Pd和Cu物种之间的氧化还原循环来实现CO氧化,且Pd+比Pd2+具有更高的CO氧化性能.反应气氛中水的存在,有利于CO在Pd+上氧化、以及金属态Pd被Cu2+物种再氧化的过程,同时水也显著促进了催化剂表面碳酸盐的生成以及抑制了活性物种Pd+生成.与表面碳酸盐累积相比,水对于活性物种Pd+生成的抑制作用是导致催化剂活性降低的主要原因.     

La2O3对Ni-Mo/γ-Al2O3催化剂CO和CO2甲烷化的影响

采用浸渍法制备了一系列Ｎｉ－Ｍｏ－Ｌａ／γ－Ａｌ２Ｏ３催化剂并测定了催化剂的ＣＯ和ＣＯ２甲 化活性采用ＴＥＭ,ＸＰＳ和ＣＯ化学吸附等手段研究了表面性质。结果表明,Ｌａ２Ｏ３的咖入提高了Ｎｉ－Ｍｏ／γ／Ａｌ２Ｏ３催化剂的ＣＯ和ＣＯ２甲烷化活性,增加了催化剂中Ｎｉ的分散度,活性表面积及催化剂表面Ｎｉ原子的浓度,降低了电子结合能。     

Influence of preliminary treatment on activity and selectivity of Co-alumosilicate catalyst in hydrocarbon synthesis from CO and H2

The temperature and medium of preliminary treatment of 10% Co/SiO ₂·Al₂O₃ influence the activity and selectivity in hydrocarbon synthesis from CO and H₂. Treatment with NH₃ reduces the yield. Increasing the treatment temperature leads to a loss of activity and a change in the composition of hydrocarbons formed. The reason for deactivation is a change in the catalyst surface texture, its adsorptive properties, and the ability to be reduced.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 8, pp. 1709–1713, August, 1990.     

Cu/Zn/Al/Mn催化剂上CO/CO2加氢合成甲醇特性研究

利用共沉淀法制备了四组分的Cu-Zn-Al-Mn和Cu-Zn-Al-Ce催化剂以及三组分的Cu-Zn-Al催化剂。利用组成H2/CO/CO2/N2=66/27/3/4(体积比)的富CO原料气对催化剂进行了活性评价，并研究了温度、压力和空速等反应条件对催化剂活性的影响。结果发现添加适量的锰助剂能显著提高催化剂的活性和热稳定性。利用SEM和XRD方法进行了催化剂的结构和形貌表征，同样表明锰助剂可以起到阻止CuO晶粒长大和促进CuO分散作用。利用富CO2的生物质原料气体积比为H2/CO/CO2/N2=50/25/20/5对Cu-Zn-Al-Mn催化剂进行的评价表明：Cu-Zn-Al-Mn催化剂上CO/CO2加氢合成甲醇的甲醇产率和选择性均有下降，在试验范围内，甲醇产率下降11％～25％，选择性为93％～95％。     

光照对Pt/Al2O3光热CO2加氢反应的增强作用（英文）

在传统热催化材料的研究领域中,光照技术已经得到了广泛的应用,从而使传统热催化剂的催化反应活性和选择性得到优化.然而,在光热协同催化反应过程中,光照因素对催化反应过程的影响尚未得到很好地研究和理解.本文通过浸渍法制得Pt/Al2O3催化剂,并应用于光热协同催化CO2加氢反应.结果证明,在光热协同CO2加氢催化反应中, Pt/Al2O3催化剂表现出光热协同效应.本文结合原位漫反射红外光谱(operandoDRIFTS)和密度泛函理论计算(DFT)对光照因素对该催化反应过程的作用机制进行了进一步深入研究.结果表明, CO气体分子从Pt纳米颗粒上的脱附过程为CO2加氢反应的重要步骤;CO气体分子在Pt纳米颗粒上脱附的位置包含台阶位置(Ptstep)和平台位置(Ptterrace).结果表明,反应过程中CO气体分子从Pt表面的脱附有利于催化剂暴露出Pt反应活性位点.值得注意的是,在光热协同催化CO2加氢反应过程中,光照和温度因素对CO气体分子的脱附过程具有不同影响.吸附能的计算结果证明, CO气体分子吸附在Ptstep和Ptterrace上的吸附能分别为-1.24和-1.43eV.由此可见, CO气体分子与Pt纳米颗粒上的Ptstep吸附位点之间相互作用更强.在无光照作用的条件下对催化剂进行加热, CO气体分子更容易从Ptterrace吸附位点发生脱附;但是在对应的温度下加入光照作用后,吸附在Ptstep位点上的CO气体分子会先转移到Ptterrace吸附位点上,随后脱附,从而促进CO2加氢反应的进行.     

Effect of zinc added to the Co/Al2O3 catalyst on the formation of carbon nanofilaments from methane and butadiene-1,3

The dynamics of carbon nanofilament growth from methane and butadiene-1,3 on Co-Zn/Al₂O₃ catalysts have been studied in the temperature range 500–750°C. The rate-limiting step in the growth of nanofilaments from butadiene is carbon atom diffusion through the bulk of the metal particle. In the case of methane, the process is controlled by one of the stages of hydrocarbon decomposition on the metal particle. The structure and morphology of the nanofilaments (composites) forming by the carbide cycle mechanism on fine zinc-promoted cobalt particles have been studied by electron microscopy and X-ray diffraction. The morphology and crystallographic properties of the nanofilaments depend on the ratio of the hydrocarbon decomposition rate (which is determined by the nature of the hydrocarbon) to the rate at which carbon atoms diffuse from their formation sites to the nanofilament formation sites (which is determined by the nature of the metal particle and by the carbon diffusion coefficient in the particle bulk). The properties of the resulting carbon nanofilaments can be controlled by varying the nature of the hydrocarbon to be decomposed and the reaction temperature and by introducing another metal into the cobalt particles.     

还原温度对Ni／Al2O3催化剂上H2,CO吸附的影响

采用程序升温还原与程序升温逐步活化、Ｈ２、ＣＯ室温吸附、Ｈ２程序升温脱附相结合的方法，研究了Ｎｉ／Ａｌ２Ｏ３催化剂上还原活化温度对其吸脱附性能的影响．实验发现，Ｎｉ／Ａｌ２Ｏ３催化剂上，在不同温度还原的不同Ｎｉ氧化物物种，经相应温度活化后可形成不同性质的Ｈ２、ＣＯ吸附中心．催化剂经５２３Ｋ及５７３Ｋ活化后可形成极细的与Ａｌ２Ｏ３有一定相互作用的吸附中心，在这类中心上，Ｈ２的室温吸附量极小，但有一定的高温Ｈ２吸附量，且高温吸附的Ｈ２要在较高温度下才能脱附，ＣＯ在其上则可能是按单金属中心多ＣＯ方式吸附的．催化剂经６７３Ｋ和７２３Ｋ活化后均形成较强的Ｈ２、ＣＯ吸附中心，ＣＯ在这些中心上可能是按线式和桥式两种方式吸附的．催化剂经６７３Ｋ活化后，形成的中心上吸附的Ｈ２可在相对较低的温度下脱附．Ｎｉ／Ａｌ２Ｏ３经７７３Ｋ处理会发生烧结，因而丧失室温Ｈ２、ＣＯ吸附能力．     

Simultaneous synthesis and consolidation of nanocrystalline 3Co–Al2O3 composite by pulsed-current-activated heating,and the mechanical properties of the material

Nanopowders of CoO and Al were fabricated by high-energy ball milling. Highly dense nanostructured 3Co–AlO₃ composite was then synthesized and consolidated, within 2 min, from mechanically activated powder (3CoO and Al) under 80 MPa pressure, by a pulsed-current-activated sintering method. The advantage of this process is that it enables very rapid densification to near theoretical density and prevents grain growth in nanostructured materials. The grain sizes of Co and Al₂O₃ in the composite were calculated. The average hardness and fracture toughness of nanostructured 3Co–AlO₃ composite were also investigated.     

Optimization and statistical analysis of Au-ZnO/Al2O3 catalyst for CO oxidation

In our former work [Catal. Today 174 (2011) 127], 12 heterogeneous catalysts were screened for CO oxidation, and Au-ZnO/Al₂O₃ was chosen and optimized in terms of weight loadings of Au and ZnO. The present study follows on to consider the impact of process parameters (catalyst preparation and reaction conditions), in conjunction with catalyst composition (weight loadings of Au and ZnO, and the total weight of the catalyst), as the optimization of the process parameters simultaneously optimized the catalyst composition. The optimization target is the reactivity of this important reaction. These factors were first optimized using response surface methodology (RSM) with 25 experiments, to obtain the optimum: 100 mg of 1.0%Au-4.1%ZnO/Al₂O₃ catalyst with 220 °C calcination and 100 °C reduction. After optimization, the main effects and interactions of these five factors were studied using statistical sensitivity analysis (SA). Certain observations from SA were verified by reaction mechanism, reactivity test and/or characterization techniques, while others need further investigation.