Synthesis and characterization of organosoluble copolyimides based on 2,2‐Bis[4‐(4‐aminophenoxy)phenyl]propane, 2,2‐Bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane and a pair of commercial aromatic dianhydrides

Organosoluble homopolyimides (PIs) and copolyimides (CoPIs) were synthesized from 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane (BAPP) or 2,2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane (6FBAPP) and six kinds of commercial aromatic dianhydrides (PMDA, II _a ; BTDA, II _b ; BPDA, II _c ; ODPA, II _d ; DSDA, II _e ; 6FDA, II _f ). Although BAPP and II _d∼f could prepare three kinds of soluble PIs ( III‐A _d∼f ), likewise 6FBAPP and II _c∼f could prepare four PIs ( III‐B _c∼f ), the insoluble PIs were synthesized from these two diamines and other dianhydrides. However, soluble CoPIs could be prepared by alternative copolycondensation from a pair of dianhydrides of soluble PIs and insoluble PIs in certain molar ratios (m₁/m₂). The ratios of m₁/m₂ of BAPP/PMDA series CoPIs ( IV _{m1(d–f)/m2a} ) ranged from 3–5, but ratios of 6FBAPP/PMDA series CoPIs ( V _{m1(c∼f)/m2a} ) decreased to 2–3. The m₁/m₂ of the BAPP/BTDA and 6FBAPP/BTDA series CoPIs were 2, while the BAPP/BPDA series were between 1–2. Composition, solubility, tensile properties and thermal properties of these CoPIs synthesized via a two‐stage thermal cyclodehydration were determined and were compared with their corresponding PIs. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3954–3961, 2000     

Synthesis and characterization of new organosoluble polyamides derived from bis[4‐(4‐carboxyphenoxy) phenyl]diphenylmethane

A new dicarboxylic acid containing a diphenylmethylene linkage, bis[4‐(4‐carboxyphenoxy)phenyl]diphenylmethane (BCAPD), was prepared from bis(4‐hydroxphenyl)diphenylmethane and p‐fluorobenzonitrile via an aromatic nucleophilic substitution reaction followed by hydrolysis. A series of novel polyamides were prepared by the direct polycondensation of BCAPD and various aromatic diamines. The polymers were produced with moderate to high inherent viscosities of 0.80–0.85 dL g^?1. Nearly all the polymers were readily soluble in polar solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide, in less polar solvents such as pyridine and cyclohexanone, and in tetrahydrofuran. All the polymers were amorphous, and the polyamide films had a tensile strength and a tensile modulus greater than 80 MPa and 2.0 GPa, respectively. These polyamides had glass‐transition temperatures between 249 and 274 °C, and their temperatures at a 10% weight loss were 477–538 and 483–540 °C in nitrogen and air atmospheres, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1156–1161, 2001     

Synthesis and characterization of new soluble polyamides from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane and various diamines

A new dicarboxylic acid monomer, 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane, bearing a pendent tert‐butylcyclohexylidene group was prepared in three steps from 4‐tert‐butylcyclohexanone. The monomer was reacted with various diamines to produce a series of new polyamides with triphenyl phosphite and pyridine as condensing agents. These polyamides were produced with inherent viscosities of 0.74 to 1.02 dL g⁻¹. All the polymers were characterized by X‐ray diffraction that revealed this amorphous nature. These polymers exhibited excellent solubility in a variety of solvents. Almost all the polymers could be dissolved in N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide, dimethyl sulfoxide, pyridine, and even in tetrahydrofuran and cyclohexanone. These polymers showed glass‐transition temperatures between 223 and 256 °C and decomposition temperatures at 10% weight loss ranging from 468 to 491 °C and 469 to 498 °C in nitrogen and air atmospheres, respectively. Transparent, tough, and flexible films of these polymers were cast from the DMAc solutions. These polymer films had tensile strengths ranging from 76 to 99 MPa, elongations at break from 7 to 19%, and initial moduli from 2.1 to 2.7 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 797–803, 2000     

Synthesis and characterization of organic–inorganic hybrid block copolymers containing a fully condensed ladder‐like polyphenylsilsesquioxane

A series of inorganic–organic hybrid block copolymers were synthesized via atom transfer radical polymerization using a fully condensed, ladder‐like structured polyphenylsilsesquioxane end‐functionalized macroinitiator. The inorganic portion, ladder‐like polyphenylsilsesquioxane, was synthesized in a one‐batch, base‐catalyzed system, whereas organic hard and soft monomers, styrene, and n‐butyl acrylate, were polymerized and copolymerized on the ends of the linear, inorganic backbone. Synthesized hybrid diblock, triblock, and random copolymers were characterized by ¹H NMR, ²⁹Si NMR, gel permeation chromatography, static light scattering, Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. Hybrid block copolymers were well‐defined with low polydispersity (<1.4) and exhibited enhanced thermal properties in the form of increased glass transition and degradation onset temperatures over their organic analogues.© 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of new soluble poly(amide‐imide)s derived from 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane

A series of new soluble poly(amide‐imide)s were prepared from the diimide‐dicarboxylic acid 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane with various diamines by direct polycondensation in N‐methyl‐2‐pyrrolidinone containing CaCl₂ with triphenyl phosphite and pyridine as condensing agents. All the polymers were obtained in quantitative yields with inherent viscosities of 0.52–0.86 dL · g^?1. The poly(amide‐imide)s showed an amorphous nature and were readily soluble in various solvents, such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide, pyridine, and cyclohexanone. Tough and flexible films were obtained through casting from DMAc solutions. These polymer films had tensile strengths of 71–107 MPa and a tensile modulus range of 1.6–2.7 GPa. The glass‐transition temperatures of the polymers were determined by a differential scanning calorimetry method, and they ranged from 242 to 279 °C. These polymers were fairly stable up to a temperature around or above 400 °C, and they lost 10% of their weight from 480 to 536 °C and 486 to 537 °C in nitrogen and air, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3498–3504, 2001     

One‐Pot Synthesis of N,N‐Disubstituted (Z)‐4‐(Halomethylidene)‐4H‐3,1‐benzothiazin‐2‐amines from 2‐(2,2‐Dihaloethenyl)phenyl Isothiocyanates and Secondary Amines

We have developed a one‐pot procedure for the preparation of N,N‐disubstituted (Z)‐4‐(halomethylidene)‐4H‐3,1‐benzothiazin‐2‐amines 3 from 2‐(2,2‐dihaloethenyl)phenyl isothiocyanates 1 , easily accessible from known 2‐(2,2‐dihaloethenyl)benzenamines by a three‐step sequence, and secondary amines. Thus, the isothiocyanates 1 react with secondary amines to afford the corresponding thiourea derivatives, of which the treatment with NaH provides the desired products.     

Synthesis and Cytotoxicity of 6‐Pyrrolidinyl‐2‐(2‐Substituted Phenyl)‐4‐Quinazolinones

In our continuing search for potential anticancer candidates, 2‐(3‐methoxyphenyl)‐6‐pyrrolidinyl‐4‐quinazolinone ( JJC‐1 ) was selected as the lead compound. Starting 5‐pyrrolidinyl‐2‐aminobenzamide was prepared using standard methodology from 5‐chloro‐2‐nitrobenzoic acid by reaction with SOCl₂, NH₃, pyrrolidine, and H₂. The starting benzamide then was reacted with 2‐substituted benzaldehyde or benzoyl chloride in N,N‐dimethylacetamide (DMAC) in the presence of NaHSO₃ at 150 °C. Thermal cyclodehydration/dehydrogenation gave the target 6‐pyrrolidinyl‐2‐(2‐substituted phenyl)‐4‐quinazolinones ( 15–22 ). These target compounds were assayed for their cytotoxicity in vitro against six cancer cell lines, including human monocytic leukemia cells (U937), mouse monocytic leukemia cells (WEHI‐3), human hepatoma cells (HepG2, Hep3B) and human lung carcinoma cells (A549, CH27). Most of them exhibited significant cytotoxic effect toward U937 and WEHI‐3 cells, with EC₅₀ values ranging from 0.30 to 10.10 μM. Compound 19 was investigated further for its action mechanisms. Preliminary findings indicated that compound 19 induced G2/M arrest and apoptosis on U937 cells.     

“Smart” poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) copolymers synthesized by nitroxide mediated radical polymerization

A series of poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) (poly(DMAEMA‐ran‐VBK)) random copolymers, with VBK molar feed compositions f_VBK,0 = 0.02–0.09, were synthesized using 10 mol % [tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino] nitroxide (SG1) relative to 2‐([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino]oxy)‐2‐methylpropionic acid (BlocBuilder) at 80 °C and 90 °C. Controlled polymerizations were observed, even with f_VBK,0 = 0.02, as reflected by a linear increase in number average molecular weight (M_n) versus conversion X ≤ 0.6 with final copolymers characterized by relatively narrow, monomodal molecular weight distributions (M_w/M_n ≈ 1.5). Poly(DMAEMA‐ran‐VBK) copolymers were deemed sufficiently pseudo‐“living” to reinitiate a second batch of N,N‐dimethylacrylamide (DMAA), with very few apparent dead chains, as indicated by the monomodal shift in the gel permeation chromatography chromatograms. Poly(DMAEMA‐ran‐VBK) random copolymers exhibited tuneable lower critical solution temperature (LCST), in aqueous solution, by modifying copolymer composition, solution pH and by the addition of the water‐soluble poly(DMAA) segment. ¹H NMR analysis determined that, in water, the VBK units of the poly(DMAEMA‐ran‐VBK) random copolymer were segregated to the interior of the copolymer aggregate regardless of solution temperature and that poly(DMAEMA‐ran‐VBK)‐b‐poly(DMAA) block copolymers formed micelles above the LCST. In addition, the final random copolymer and block copolymer exhibited temperature dependent fluorescence due to the VBK units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Amphiphilic Poly(4‐acryloylmorpholine)/Poly[2‐(N‐carbazolyl)ethyl acrylate] Random and Block Copolymers Synthesized by NMP

A series of random copolymers and block copolymers containing water‐soluble 4AM and fluorescent VAK are synthesized by NMP. The homopolymerizations of 4AM and VAK and 4AM/VAK random copolymerization are performed in 50 wt% DMF using 10 mol% SG1, resulting in a linear increase in versus conversion, and final polymers with narrow molecular weight distributions ( < 1.4). Reactivity ratios r_VAK = 0.64 ± 0.52 and r_4AM = 0.86 ± 0.66 are obtained for the 4AM/VAK random copolymerization. In addition, a poly(4AM) macroinitiator is used to initiate a surfactant‐free suspension polymerization of VAK. After 2.5 h, the resulting amphiphilic block copolymer has = 12.6 kg · mol^?1, = 1.48, molar composition F_VAK = 0.38 with latex particle sizes between 270 and 475 nm.

     

Synthesis and properties of new polyamides derived from 2,2‐bis[4‐[2‐(4‐aminophenoxy)ethoxy]phenyl]sulfone by direct polycondensation

A series of new polyamides containing both sulfone and oxyethylene moieties in the polymer chain was prepared by the direct polycondensation of the diamine monomer 2,2‐bis[4‐[2‐(4‐aminophenoxy)ethoxy]phenyl]sulfone (BAEPS) and various aromatic dicarboxylic acids in N‐methyl‐2‐pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. Polymers were produced with inherent viscosities of 0.30–0.60 dl/g and identified by elemental analysis, and infrared and nuclear magnetic resonance spectra. Most of the polymers were readily dissolved in polar solvents such as NMP, dimethylsulfoxide, N,N‐dimethylacetamide, N,N‐dimethylformamide and m‐cresol at room temperature. Polymers containing rigid and symmetric p‐phenylene, naphthalene and p‐biphenylene moieties revealed a crystalline nature and showed no solubility in organic solvents. These polyamides had 10% weight loss temperatures ranging between 423 and 465 °C in nitrogen atmosphere and glass transition temperatures between 170 and 305 °C. The polymers with crystallinity nature exhibited melting endotherms (T_m) below 386 °C in differential scanning calorimetry trace. Copyright © 1999 John Wiley & Sons, Ltd.     

Synthesis and characterization of near‐monodisperse electron acceptor homopolymers of 2‐[(3,5‐dinitrobenzoyl)oxy]ethyl methacrylate

Homopolymers of 2‐(trimethylsiloxy)ethyl methacrylate of degrees of polymerization from 5 to 50 were synthesized by group transfer polymerization in tetrahydrofuran (THF) using 1‐methoxy‐1‐(trimethylsiloxy)‐2‐methyl propene as the initiator and tetrabutylammonium bibenzoate as the catalyst. These polymers were first converted to poly[2‐(hydroxy)ethyl methacrylate]s by removal of the trimethylsilyl‐protecting groups by acidic hydrolysis, and subsequently transformed to poly{2‐[(3,5‐dinitrobenzoyl)oxy]ethyl methacrylate}s by reaction with 3,5‐dinitrobenzoyl chloride in the presence of triethylamine. Gel permeation chromatography in THF and proton nuclear magnetic resonance (¹H NMR) spectroscopy in CDCl₃ and d₆ dimethyl sulfoxide were used to characterize the polymers in terms of their molecular weight and composition. The molecular weights were found to be close to the values expected from the polymerization stoichiometry and the molecular weight distributions were narrow, with polydispersity indices around 1.1. The hydrolysis and reesterification steps were found to be almost quantitative for all polymers. Differential scanning calorimetry and thermal gravimetric analysis were also employed to measure the glass transition temperatures (T_g 's) and decomposition temperatures, which were determined to be approximately 80 and 320 °C, respectively. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1457–1465, 2000     

Facile Synthesis of Substituted Ethyl 2‐(Chloromethyl)‐2‐hydroxy‐2H‐1‐benzopyran‐3‐carboxylates

Ethyl 2‐(chloromethyl)‐2‐hydroxy‐2H‐chromene‐3‐carboxylates 2a – 2j have been synthesized by reaction of substituted salicylaldehydes with ethyl 4‐chloro‐3‐oxobutanoate, in the presence of piperidine in CH₂Cl₂ at room temperature, in good yields.     

Synthesis,characterization, and curing kinetics of novel ladder‐like polysilsesquioxanes containing side‐chain maleimide groups

Two ladder‐like polysilsesquioxanes (LPS) containing side‐chain maleimide groups have been synthesized successfully by reacting N‐(4‐hydroxyphenyl)maleimide (HPM) with LPS containing 100 mol % of chloropropyl groups (Ladder A ) and 50 mol % of each methyl and chloropropyl group (Ladder B ). HPM was synthesized by reacting maleic anhydride with 4‐aminophenol, and the resulting amic acid was imidized using p‐toluenesulfonic acid as a catalyst (Scheme 1 ). The LPSs were characterized by Fourier transform infrared (FTIR), ¹H nuclear magnetic resonance (NMR), proton‐decoupled ¹³C NMR, ²⁹Si NMR, wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Characterization indicated that these polymers had ordered ladder‐like structures with possible defects. These polymers were soluble in common solvents at ambient temperature, which suggested that they were not crosslinked. Both the polymers and the HPM were cured, and their kinetics were followed by dynamic DSC. The Ozawa and Kissinger methods were used to calculate activation energies for curing. Curing increased the temperature at which both 5% weight loss and maximum rate of weight loss were observed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4036–4046, 2004     

Efficient One‐Pot Synthesis of Alkyl 2‐(Dialkylamino)‐4‐phenylthiazole‐5‐carboxylates and Single‐Crystal X‐Ray Structure of Methyl 2‐(Diisopropylamino)‐4‐phenylthiazole‐5‐carboxylate

The reaction between secondary amines, benzoyl isothiocyanate, and dialkyl acetylenedicarboxylates (=dialkyl but‐2‐ynedioates) in the presence of silica gel (SiO₂) led to alkyl 2‐(dialkylamino)‐4‐phenylthiazole‐5‐carboxylates in fairly high yields. The structures of the products were confirmed by their IR, ¹H‐ and ¹³C‐NMR, and mass spectra, and by a single‐crystal X‐ray structure determination.     

Synthesis of a new monomer N′‐(β‐methacryloyloxyethyl)‐2‐pyrimidyl‐(p‐benzyloxycarbonyl)aminobenzenesulfonamide and its copolymerization with N‐phenyl maleimide

The new monomer N′‐(β‐methacryloyloxyethyl)‐2‐pyrimidyl‐(p‐benzyloxy‐ carbonyl)aminobenzenesulfonamide (MPBAS) (M₁) is synthesized using sulfadiazine as parent compound. It could be homopolymerized and copolymerized with N‐phenyl maleimide (NPMI) (M₂) by radical mechanism using AIBN as initiator at 60 °C in dimethylformamide. The new monomer MPBAS and polymers were identified by IR, element analysis and ¹H NMR in detail. The monomer reactivity ratios in copolymerization were determined by YBR method, and r₁ (MPBAS) = 2.39 ± 0.05, r₂ (NPMI) = 0.33 ± 0.02. In the presence of ammonium formate, benzyloxycarbonyl groups could be broken fluently from MPBAS segments of copolymer by catalytic transfer hydrogenation, and the copolymer with sulfadiazine side groups are recovered. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2548–2554, 2000     

Supramolecular Architectures of Four New Transition Metal Complexes with 3‐[4‐(Carboxymethoxy)phenyl]propanoic Acid and N‐[4‐(Carboxymethoxy)phenyl]iminodiacetic Acid

Four new transition metal complexes: [Cu(Hcppa)₂(H₂O)₂] ( 1 ), [Co₂(cppa)₂(H₂O)₁₀] ( 2 ), [Co₃(cpia)₂(H₂O)₈] · 2H₂O ( 3 ) and [Ni₃(cpia)₂(H₂O)₁₂] · 6H₂O ( 4 ) {H₂cppa = 3‐(4‐(carboxymethoxy)phenyl]propanoic acid; H₃cpia = N‐[4‐(carboxymethoxy)phenyl]iminodiacetic acid} were synthesized and characterized. Complexes 1 and 2 show mononuclear structures, complexes 3 and 4 exhibit dinuclear structures. All complexes extend to 3D supramolecular networks through hydrogen bonds, of which complexes 3 and 4 display microporous structures. In complexes 2 – 4 the water clusters are trapped by the cooperative association of coordinate interactions as well as hydrogen bonds, forming different 1D metal‐water chain structures. Thermal stabilities of complexes 1 – 4 were discussed.     

Effects of diamines and their fluorinated groups on the color lightness and preparation of organosoluble aromatic polyimides from 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]‐hexafluoropropane

To investigate the position and amount of the CF₃ group affecting the coloration of polyimides (PIs), we prepared 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]hexafluoropropane ( 2 ) with four CF₃ groups with 2‐chloro‐5‐nitrobenzotrifluoride and 2,2‐bis(4‐hydroxyphenol)hexafluoropropane. A series of soluble and light‐colored fluorinated PIs ( 5 ) were synthesized from 2 and various aromatic dianhydrides ( 3a – 3f ). 5a – 5f had inherent viscosities ranging from 0.80 to 1.19 dL/g and were soluble in amide polar solvents and even in less polar solvents. The glass‐transition temperatures of 5 were 221–265 °C, and the 10% weight‐loss temperatures were above 493 °C. Their films had cutoff wavelengths between 343 and 390 nm, b* values (a yellowness index) ranging from 5 to 41, dielectric constants of 2.68–3.01 (1 MHz), and moisture absorptions of 0.03–0.29 wt %. In a comparison of the PI series 6 – 8 based on 2,2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane, 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]propane, and 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane, we found that the CF₃ group close to the imide group was more effective in lowering the color; this means that CF₃ of 5 , 7 , and 8f was more effective than that of 6c . The color intensity of the four PI series was lowered in the following order: 5 > 7 > 6 > 8 . The PI 5f , synthesized from diamine 2 and 4,4′‐hexafluoroisopropylidenediphthalic anhydride, had six CF₃ groups in a repeated segment, so it exhibited the lightest color among the four series. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 922–938, 2003     

5，10，15，20-四 [4-(4''-乙基哌嗪基)苯基]卟啉的合成及其与DNA的相互作用

基于卟啉对癌细胞的特殊亲和作用和哌嗪化合物的抗肿瘤、抗病毒作用，设计并合成了具有哌嗪结构的新型卟啉化合物5，10，15，20-四[4-(4'-乙基哌嗪基)苯基]卟啉（TEPPPH₂），其结构经UV-Vis, 元素分析，¹H NMR等手段证明。采用UV-Vis光谱和荧光光谱研究了TEPPPH₂和小牛胸腺DNA 的相互作用模式和结合机理。实验发现，TEPPPH₂能嵌入到DNA的碱基对中，1个小牛胸腺DNA分子对TEPPPH₂分子的最大结合数n约为88，结合常数为8.4×10⁶mol•L^-1 。TEPPPH₂与DNA的结合数和结合常数大于已知的四（4-N-甲基吡啶基）卟啉和Ca/sal-his、Ni/sal–aln型席夫碱抗癌药物。