Synthesis of networked polymer based on ring‐opening addition reaction of 1,3‐benzoxazine with resorcinol

A highly efficient ring‐opening addition reaction of benzoxazine at ambient temperature has been developed with 2‐methylresorcinol as a nucleophilic reagent. In this reaction, 2‐methylresorcinol reacted with two equivalent amount of benzoxazine to give the corresponding 1:2 adduct, demonstrating its potential as a bifunctional nucleophile. Based on this reaction, a new crosslinking system consisting of a polymer bearing benzoxazine moieties in the side chains and 2‐methylresorcinol as a crosslinker has been performed to obtain the corresponding networked polymer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Promoting effect of thiophenols on the ring‐opening polymerization of 1,3‐benzoxazine

Thiophenol and p‐nitrothiophenol were evaluated as promoters for the ring opening polymerization of benzoxazine. The ring‐opening polymerization of p‐cresol type monofunctional N‐phenyl benzoxazine 1a with 10 mol % of thiophenols proceeded at 150 °C, leading to the high conversion of 1a more than 95% within 5 h, whereas the polymerization of 1a without thiophenols did not proceed under the same conditions. The promotion effect of the thiophenols on curing of bisphenol‐A type N‐phenyl benzoxazine 1b was also investigated. In the differential scanning calorimetric (DSC) analysis of the polymerization of 1b at 150 °C without using any promoters, an exothermic peak attributable to the ring‐opening reaction of benzoxazine was observed after 8 h. In contrast, in the DSC analysis of the polymerization of 1b with addition 20 mol % of p‐nitrothiophenol, an exothermic peak was observed within 2 h, to clarify the significant promoting effect of p‐nitrothiophenol. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2523–2527     

Controlled ring‐opening polymerization of L‐lactide and 1,5‐dioxepan‐2‐one forming a triblock copolymer

Novel elastomeric A‐B‐A triblock copolymers were successfully synthesized in a new two‐step process: controlled ring‐opening polymerization of the cyclic ether–ester 1,5‐dioxepan‐2‐one as the amorphous middle block (B‐block) followed by addition and polymerization of the two semicrystalline L ‐lactide blocks (A‐block). A 1,1,6,6‐tetra‐n‐butyl‐1,6‐distanna‐2,5,7,10‐tetraoxacyclodecane initiator system was utilized and the reaction was performed in chloroform at 60 °C. A good control of the synthesis was obtained, resulting in well defined triblock copolymers. The molecular weight and chemical composition were easily adjusted by the monomer‐to‐initiator ratio. The triblock copolymers formed exhibited semicrystallinity up to a content of 1,5‐dioxepan‐2‐one as high as 89% as determined by differential scanning calorimetry. WAXS investigation of the triblock copolymers showed a crystal structure similar to that of the pure poly(L ‐lactide). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1774–1784, 2000     

Reaction of o‐Carboryne with Furans: Facile Synthesis of Carborane‐ Fused Oxanorbornenes and Their Derivatives

o‐Carboryne (1,2‐dehydro‐o‐carborane) is a very useful synthon for the synthesis of a variety of carborane‐functionalized molecules. Diels‐Alder reaction of o‐carboryne with furans gave a series of carborane‐fused oxanorbornenes in moderate to high yields using 1‐OTf‐1,2‐C₂B₁₀H₁₁ as carboryne precursor. The resultant cycloadducts can undergo hydrogenation, cyclic oxidation, bromination, [4 + 2]/[2 + 2] cycloaddition and nucleophilic ring opening reaction to afford a variety of highly functionalized carboranes that may find applications as useful basic units in medicine and materials science.     

Copper(I)‐Catalyzed Asymmetric [3+2]‐Cycloaddition of α‐Substituted Iminoesters with α‐Trifluoromethyl α,β‐Unsaturated Esters

Reported herein is an example of highly regio‐, diastereo‐ and enantioselective Cu(I)‐catalyzed intermolecular [3+2] cycloaddition reaction of α‐substituted iminoesters with α‐trifluoromethyl α,β‐unsaturated esters. This novel strategy provided a facile access to pyrrolidines with two skipped (aza)quaternary stereocenters including a CF₃ all‐carbon quaternary stereocenter. A broad substrate scope was observed and high yields (up to 94%) with excellent diastereoselectivity (up to >20 : 1 d.r.) and enantioselectivity (up to 98% ee) were obtained.     

Filling‐level effect on the physical properties of MgBr2‐ and MgCl2‐filled poly(vinyl acetate) films

The structural properties of poly(vinyl acetate) (PVAc) films filled with different levels of MgBr₂ or MgCl₂ were investigated. Differential scanning calorimetry revealed that, at certain filling levels of MgBr₂ or MgCl₂, two new transitions appeared. The first one was due to the α relaxation (T_α) associated with a crystalline region, and the second was due to the melting temperature (T_m). This implies that a crystalline phase was formed in the polymeric matrix. Changes occurring in T_α, T_m, and the melting peak area as a function of the filling level were examined. The X‐ray diffraction (XRD) pattern revealed that the pure PVAc film was amorphous. However, the addition of MgBr₂ or MgCl₂ led to the formation of a crystalline phase in the polymeric matrix that depended on the filling level. XRD also demonstrated that the structural changes depended not only on the metal ions but also on the halide ions. Scanning electron microscopy images for the studied samples were examined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 112–119, 2003     

Polymerization of n‐hexyl isocyanate with CpTiCl2(OR) (R = functional group or macromolecular chain): A route to ω‐functionalized and block copolymers and terpolymers of n‐hexyl isocyanate

Well‐defined ω‐cholesteryl poly(n‐hexyl isocyanate) (PHIC–Chol), as well as diblock copolymers of n‐hexyl isocyanate (HIC) with styrene, PS‐b‐PHIC [PS = polystyrene; PHIC = poly(n‐hexyl isocyanate)], and triblock terpolymers with styrene and isoprene, PS‐b‐PI‐b‐PHIC and PI‐b‐PS‐b‐PHIC (PI = polyisoprene), were synthesized with CpTiCl₂(OR) (R = cholesteryl group, PS, or PS‐b‐PI) complexes. The synthetic strategy involved the reaction of the precursor complex CpTiCl₃ with cholesterol or the suitable ω‐hydroxy homopolymer or block copolymer, followed by the polymerization of HIC. The ω‐hydroxy polymers were prepared by the anionic polymerization of the corresponding monomers and the reaction of the living chains with ethylene oxide. The reaction sequence was monitored by size exclusion chromatography, and the final products were characterized by size exclusion chromatography (light scattering and refractive‐index detectors), nuclear magnetic resonance spectroscopy, and, in the case of PHIC–Chol, differential scanning calorimetry. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6503–6514, 2005     

Binary versus ternary interactions in a completely miscible three‐polymer blend system: Poly(ϵ‐caprolactone) with two different methacrylic polymers

A truly miscible ternary miscible blend consisting of poly(?‐caprolactone) (PCL), poly(phenyl methacrylate), and poly(benzyl methacrylate) (PBzMA) was discovered. The three‐polymer blend system was completely miscible within the entire composition range at ambient temperature up to about 150 °C, and ternary phase diagrams at increasing temperatures were characterized and interpreted. A ternary‐interaction model based on the modified Flory–Huggins expression was used to describe the phase diagrams with the individual binary interaction strengths. The model fitted well with the experimental‐phase diagram for the ternary blend system at T = 250 °C, where the binary PCL‐PBzMA blend system is on the critical points of phase separation. Interpretation of discrepancy between the model and experimental at other temperatures was handled with an empirical approach. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 747–754, 2002     

Thermal analysis of 1,4‐di[n′‐(quinolyl)]buta‐1,3‐diynes,structure, and topo‐oligomerization: Polymerization of 3‐ethynylquinoline with the triethyl aluminum/vanadium 2,4‐pentanedionate catalyst system

Conjugated 1,4‐bis(n′‐quinolyl)‐1,3‐butadiynes were obtained through the oxidative dimerization of the corresponding n′‐ethynylquinolines catalyzed by cuprous chloride. Differential scanning calorimetry analysis of the 1,4‐bis[n′‐(quinolyl)]buta‐1,3‐diyne molecules produced evidence of a syn–anti rotational equilibrium around the 1,3‐diyne axis and an irreversible transformation into a thermopolymer. The topo‐oligomerization of 1,4‐bis[3′‐(quinolyl)]buta‐1,3‐diyne, which took place by irradiation with sunlight, was investigated with matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. Accurate X‐ray molecular structure and refinement analysis of 1,4‐bis[3′‐(quinolyl)]buta‐1,3‐diyne was conducted. The molecular crystalline packing consisted of parallel arrays of two groups of centrosymmetric molecules (antirotamer) in a herringbone assemblage in the solid state. The polymerization of 3‐ethynylquinoline was carried out with the AlEt₃/V(acac)₃ system to produce a mixture of 1,2,4‐ and 1,3,5‐tris(3′‐quinolyl)benzene cyclotrimers and a trans–cisoid polyene structure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6031–6040, 2004     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. I. Samples crystallized from the glassy state

The melting behavior of poly(L ‐lactic acid) film crystallized from the glassy state, either isothermally or nonisothermally, was studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), differential scanning calorimetry (DSC), and temperature‐modulated differential scanning calorimetry (TMDSC). Up to three crystallization and two melting peaks were observed. It was concluded that these effects could largely be accounted for on the basis of a “melt‐recrystallization” mechanism. When molecular weight is low, two melting endotherms are readily observed. But, without TMDSC, the double melting phenomena of high molecular weight PLLA is often masked by an exotherm just prior to the final melting, as metastable crystals undergo melt‐recrystallization during heating in the DSC. The appearance of a double cold‐crystallization peak during the DSC heating scan of amorphous PLLA film is the net effect of cold crystallization and melt‐recrystallization of metastable crystals formed during the initial cold crystallization. Samples cold‐crystallized at 80 and 90 °C did not exhibit a long period, although substantial crystallinity developed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3200–3214, 2006     

Synthesis and morphological characterization of miktoarm star copolymers (PCL)2(PS)2 of poly(ε‐caprolactone) and polystyrene

An heterofunctional initiator combining two reactive sites for ring opening polymerization and two for atom transfer radical polymerization was used to prepare three A₂B₂ miktoarm star copolymers of poly(ε‐caprolactone) (PCL) and polystyrene (PS). The morphology and thermal properties were studied by transmission electron microscopy, polarized light optical microscopy, and differential scanning calorimetry. The (PCL)₂(PS)₂ 72/28 (72 wt % PCL) sample was crystallized from a disordered melt. In this case, crystallization drove the structure formation and a lamellar morphology was obtained at the microdomain level, while spherulites were observed at a superstructural level. The other two samples, 39/61 and 27/73, with lower PCL content and higher total molecular weight, were not able to form spherulites. Surprisingly, these miktoarm star copolymers exhibited hexagonally packed cylinders and spheres morphologies, respectively, instead of lamellar and cylindrical morphology. Such unexpected and novel behavior was explained in terms of the higher resistance of the arms to be stretched in a miktoarm star copolymer when compared with the corresponding linear diblocks. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5387–5397, 2007     

Statistical copolymers of norbornene and 5‐vinyl‐2‐norbornene by a ditungsten complex mediated ring‐opening metathesis Polymerization: Synthesis,thermal properties,and kinetics of thermal decomposition

Statistical copolymers of norbornene (NBE) with 5‐vinyl‐2‐norbornene (VNBE) were prepared by ring‐opening metathesis polymerization, employing the triply bonded ditungsten complex Na[W₂(μ‐Cl)₃Cl₄(THF)₂].(THF)₃. NMR measurements revealed that the side vinyl groups of the VNBE monomer remain intact during the copolymerization reaction. The reactivity ratios were estimated using the Finemann–Ross (FR), the inverted FR, and the Kelen–Tüdos graphical methods. Structural parameters of the copolymers were obtained by calculating the dyad sequence fractions, which were derived using the monomer reactivity ratios. The glass transition temperatures, T_g, of the copolymers were measured by differential scanning calorimetry measurements and were examined in the frame of several theoretical equations allowing the prediction of these T_g values. The best fit was obtained using methods that take into account the monomer sequence distribution of the copolymers. Finally, the kinetics of the thermal decomposition of the copolymers was studied by thermogravimetric analysis in the frame of the Ozawa–Flynn–Wall and Kissinger methods. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4835–4844     

Cationic ring‐opening polymerization of novel 1,3‐dehydroadamantanes with various alkyl substituents: Synthesis of thermally stable poly(1,3‐adamantane)s

Cationic ring‐opening polymerizations of 5‐alkyl‐ or 5,7‐dialkyl‐1,3‐dehydroadamantanes, such as 5‐hexyl‐ ( 4 ), 5‐octyl‐ ( 5 ), 5‐butyl‐7‐isobutyl‐ ( 6 ), 5‐ethyl‐7‐hexyl‐ ( 7 ), and 5‐butyl‐7‐hexyl‐1,3‐dehydroadamantane ( 8 ), were carried out with super Brønsted acids, such as trifluoromethanesulfonic acid or trifluoromethanesulfonimide in CH₂Cl₂ or n‐heptane. The ring‐opening polymerizations of inverted carbon–carbon bonds in 4–8 proceeded to afford corresponding poly(1,3‐adamantane)s in good to quantitative yields. Poly( 4–8 )s possessing alkyl substituents were soluble in 1,2‐dichlorobenzene, although a nonsubstituted poly(1,3‐adamantane) was not soluble in any organic solvent. In particular, poly( 8 ) exhibited the highest molecular weight at around 7500 g mol^?1 and showed excellent solubility in common organic solvents, such as THF, CHCl₃, benzene, and hexane. The resulting poly( 4–8 )s containing adamantane‐1,3‐diyl linkages showed good thermal stability, and 10% weight loss temperatures (T₁₀) were observed over 400 °C. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4111–4124     

Copolymerization of ethylene with cyclopentene or 2‐butene with half titanocenes‐based catalysts

Half titanocenes (CpCH₂CH₂O)TiCl₂ (1), (CpCH₂CH₂OCH₃)TiCl₃ (2), and CpTiCl₃ (3), activated by methylaluminoxane (MAO) were tested in copolymerization of ethylene with internal olefins such as cyclopentene. All the catalysts were able to give incorporation of cyclopentene in polyethylene matrix. ¹³C NMR analysis of obtained copolymers showed that the catalytic systems have low regiospecificity. In fact, in ethylene–cyclopentene copolymers, cyclic olefin inserts with both 1,2 and 1,3‐enchainment. X‐ray powder diffraction analysis of these copolymers confirmed that 1,2 inserted cyclopentene units are excluded from crystalline phase, whereas 1,3‐cyclopentene units are included, giving rise to expansion of unit cell of crystalline polyethylene. Titanium‐based catalysts were investigated also in the copolymerization of ethylene with E and Z‐2‐butene. Only complex (1) was able to give copolymers and ¹³C NMR analysis of products showed 2‐3, 1‐3, and 1‐2 insertion of 2‐butene. Differential scanning calorimetry analysis displayed that ethylene–cyclopentene, as well as ethylene‐2‐butene, copolymers are crystalline and their melting point decreases by increasing the comonomer content. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4725–4733, 2008     

Main‐chain chiral poly(2‐oxazoline)s: Influence of alkyl side‐chain on secondary structure formation in solution

The synthesis and microwave‐assisted polymerization of a series of chiral 2‐oxazolines with varying alkyl pendant groups, namely R‐2‐ethyl‐4‐ethyl‐2‐oxazoline (R‐EtEtOx), R‐2‐butyl‐4‐ethyl‐2‐oxazoline (R‐BuEtOx), R‐2‐octyl‐4‐ethyl‐2‐oxazoline, 2‐nonyl‐4‐ethyl‐2‐oxazoline, and R‐2‐undecyl‐4‐ethyl‐2‐oxazoline (R‐UndeEtOx), are reported. A kinetic investigation of the polymerization of R‐EtEtOx revealed a living polymerization mechanism. The poly(2‐oxazoline)s containing an ethyl, butyl, and octyl pendant group form similar chiral structures according to circular dichroism measurements. When the pendant group is further elongated, the chiral structure becomes more flexible in trifluoroethanol and the thermal response in hexafluoroisopropanol (HFIP) significantly changes. The short‐range structure of poly‐R‐BuEtOx dissolved in HFIP is thermoresponsive in a complex way, due to HFIP hydrogen bonding to the polymeric amide groups, whereas the long‐range structure determined from small angle neutron scattering is insensitive to temperature demonstrating that only the local secondary structure changes with temperature. In addition, the chiral structure of poly‐R‐UndeEtOx depends on the polarity of the solvent. The short‐range structure becomes more flexible in polar solvents, most likely due to interactions with the amide groups disturbing the secondary structure. In contrast, the long‐range structural transition from an ellipsoid in the apolar n‐hexane to a rod structure in the polar n‐butanol is ascribed to better solvation of the long aliphatic side chains. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Microphase segregation and selective chain scission of poly(2‐methyl‐2‐oxazoline)‐block‐polystyrene

Herein, we report the design and synthesis of a block copolymer (BCP) with a high Flory–Huggins interaction parameter to access 10 nm feature sizes for potential lithographic applications. The investigated BCP is poly[(2‐methyl‐2‐oxazoline)‐block‐styrene] (PMeOx‐b‐PS), where the PMeOx segment functions as a hydrophilic segment. Two BCPs with different molecular weights were prepared using PMeOx as macroinitiator for copper(0) mediated controlled radical polymerization. The thin film self‐assembly of the obtained PMeOx‐b‐PS was performed by solvent annealing and investigated by atomic force microscopy. Both polymers formed PMeOx cylinders in a PS matrix with an average cylinder diameter of 10.5 nm. Additionally, the ability of the PMeOx domains to selectively degrade under ultraviolet irradiation was explored. It was shown that scission of the PMeOx block does occur selectively, and furthermore that the degraded domains can be removed while leaving the PS matrix intact. By combining synthetic accessibility, small feature sizes, and a selectively cleavable domain, this new BCP system holds significant promise as a lithographic mask for patterning surfaces with high precision. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1349–1357     

Determination of the crystallinity of polyethylene/α‐olefin copolymers by thermal analysis: Relationship of the heat of fusion of 100% polyethylene crystal and the density

The heat of fusion measured with differential scanning calorimetry (DSC) is typically divided by a constant value of the heat of fusion of 100% polyethylene (PE) crystal (ΔH) for the estimation of the fraction crystallinity of PE copolymers, regardless of the density [i.e., the short‐chain branching (SCB) concentration]. In this work, values of ΔH of about 288 J/g were determined with a combined DSC and X‐ray diffraction (XRD) method for a series of PE copolymers containing SCB from 0 to 50 Br/1000 C (density = 0.965–0.865 g/cc). There was no systematic change in ΔH observed across this density range. This result supports the suitability of determining the fraction crystallinity of PE of any density by the simple division of the observed heat of fusion determined by DSC by a constant value of ΔH. This DSC method yielded values of PE crystallinity in good agreement with corresponding values determined by XRD for a series of PE copolymers. The determination of ΔH involved a small precision error for higher density (lower SCB) PEs, but the precision error increased for lower density (i.e., higher SCB) PEs. This was due to the difficulty in measuring the heat of fusion for lower density PEs, which exhibited low values of the heat of fusion and melted only slightly above room temperature, and due to the difficulty of measuring lower values of crystallinity by XRD. The crystal thickness measured by small‐angle X‐ray scattering for this series of PE copolymers decreased exponentially from about 280 to 6 Å. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1637–1643, 2002