Fracture and crack profile fictitious crack modeling of porous poly(methyl methacrylate)

This article presents the fracture behavior and applicability of the fictitious crack (FC) model to describe the fracture of a porous poly(methyl methacrylate) material. Two test geometries, wedge‐opening load and single‐edge‐notched beam, were employed under two different test conditions (room temperature and in water at 45 °C); all presented quasibrittle fracture behavior. The crack profile of a wedge‐opening load sample was visualized and measured with the digital image correlation technique. The mechanical response of all the samples, including the crack profile, was successfully modeled with the FC model, and this showed the good applicability of this model to the fracture of this granular poly(methyl methacrylate) material. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1112–1122, 2003     

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with poly(butadiene-block-methyl methacrylate)

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with butadiene-methyl methacrylate diblock copolymers has been investigated by transmission electron microscopy. When the diblock copolymers are added to the blends, the size of PB particles decreases and their size distribution gets narrower. In PB/PMMA7.6K blends with P(B-b-MMA)25.2K as a compatibilizer, most of micelles exist in the PMMA phase. However, using P(B-b-MMA)38K as a compatibilizer, the micellar aggregation exists in PB particles besides that existing in the PMMA phase. The core of a micelle in the PMMA phase is about 10 nm. In this article the influences of temperature and homo-PMMA molecular weight on compatibilization were also examined. At a high temperature PB particles in blends tend to agglomerate into bigger particles. When the molecular weight of PMMA is close to that of the corresponding block of the copolymer, the best compatibilization result would be achieved. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 85–93, 1998     

Fracture behavior of amorphous and semicrystalline blends of poly(vinylidene fluoride) and poly(methyl methacrylate)

The fracture behavior of blends of poly(vinylidene fluoride) and poly(methyl methacrylate) was investigated all over the composition range. A detailed analysis of the net stress versus crack opening displacement curves was performed. Fracture surface observations allowed statements on the process zone characteristics ahead of the crack tip. For the amorphous blends, the crack initiation energy is well related to the glass transition temperature. For the semicrystalline blends, the fracture energy is correlated with the degree of crystallinity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Interpenetrating polymer networks of poly(dimethyl siloxane–urethane) and poly(methyl methacrylate)

Simultaneous IPNs of poly(dimethyl siloxane-urethane) (PDMSU)/poly(methyl methacrylate) (PMMA) and related isomers have been prepared by using new oligomers of bis(β-hydroxyethoxymethyl)poly(dimethyl siloxane)s (PDMS diols) and new crosslinkers biuret triisocyanate (BTI) and tris(β-hydroxylethoxymethyl dimethylsiloxy) phenylsilane (Si-triol). Their phase morphology have been characterized by DSC and SEM. The SEM phase domain size is decreased by increasing crosslink density of the PDMSU network. A single phase IPN of PDMSU/PMMA can be made at an M_c = 1000 and 80 wt % of PDMSU. All of the pseudo- or semi-IPNs and blends of PDMSU and PMMA were phase separated with phase domain sizes ranging from 0.2 to several micrometers. The full IPNs of PDMSU/PMMA have better thermal resistance compared to the blends of linear PDMSU and linear PMMA. © 1993 John Wiley & Sons, Inc.     

Property modification of poly(methyl methacrylate) through copolymerization with fluorinated aryl methacrylate monomers

Copolymers of methyl methacrylate (MMA) with 2,3,5,6‐tetrafluorophenyl methacrylate (TFPMA), pentafluorophenyl methacrylate (PFPMA), and 4‐trifluoromethyl‐2,3,5,6‐tetrafluorophenyl methacrylate (TFMPMA) were investigated. All the three systems showed a random copolymerization character. The composition, glass transition temperature (T_g), and refractive index of the copolymers obtained were studied. T_gs of TFPMA/MMA and PFPMA/MMA copolymers were found to deviate positively from the Gordon–Taylor equation. However, T_gs of TFMPMA/MMA copolymers were well fit with the Gordon–Taylor equation. These results indicated the existence of interaction between MMA and either TFPMA or PFPMA units in copolymers. This interaction resulted in the enhancement of the T_g of MMA polymers through the copolymerization with TFPMA and PFPMA. The refractive index and the light transmittance of copolymers were close to those of PMMA. Copyright © 2007 John Wiley & Sons, Ltd.     

Nanocarbon-poly(methyl methacrylate) composite materials

Nanocarbon-poly(methyl methacrylate) sols were prepared by pulsed laser ablation at the interface of target submerged in flowing liquid (PLA-IT/SFL) method, and the corresponding composite films were prepared by solution-casting. Spectra results indicated that there existed interactions between nanocarbon and the polymethyl methacrylate (PMMA) matrix, which was consistent with the decrease in glass transition temperature of the composites with increase of carbon content. TEM images revealed that a carbon encapsulated core/shell structure was formed in the composites, which could ensure good dispersion of carbon nanoparticles within the PMMA matrix. The decomposition of the composites was less influenced by the introduction of nanocarbon particles. Translated from Acta Polymerica Sinica 2006, 2(2) (in Chinese)     

Thermal oxidation of blends of poly(ethylene oxide) and poly(methyl methacrylate)

Thermal oxidation of poly(ethylene oxide) (PEO) and its blends with poly(methyl methacrylate) (PMMA) were studied using oxygen uptake measurements. The rates of oxidation and maximum oxygen uptake contents were reduced as the content of PMMA was increased in the blends. The results were indicative of a stabilizing effect by PMMA on the oxidation of PEO. The oxidation reaction at 140°C was stopped at various stages and PMMA was separated from PEO and its molecular weights were measured by gel permeation chromatography (GPC). The decrease in the number-average molecular weight of PMMA was larger as the content of PEO increased in the blends. The visual appearance of the films suggested that phase separation did not occur after thermal oxidation. The activation energy for the rates of oxidation in the blends was slightly increased compared to pure PEO. © 1992 John Wiley & Sons, Inc.     

Observations of crystallization and melting in poly(ethylene oxide)/poly(methyl methacrylate) blends by hot-stage atomic-force microscopy

The binary blend of poly(ethylene oxide)/atactic poly(methyl methacrylate) is examined using hot-stage atomic-force microscopy (AFM) in conjunction with differential scanning calorimetry and optical microscopy. It was found possible to follow in real time the melting process, which reveals itself to be nonuniform. This effect is ascribed to the presence of lamellae having different thicknesses. The crystallization process of poly(ethylene oxide) from the miscible melt is also followed in real time by AFM, affording detailed images of the impingement of adjacent spherulites and direct observation of lamellar growth and subsequent polymer solidification in the interlamellar space.© 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2643–2651, 1998     

Stress–strain behavior of low‐density polyethylene/poly(methyl methacrylate) blends with modulated interfaces with a hydrogenated polybutadiene‐block‐poly(methyl methacrylate) diblock copolymer

The stress–strain diagrams and ultimate tensile properties of uncompatibilized and compatibilized hydrogenated polybutadiene‐block‐poly(methyl methacrylate) (HPB‐b‐PMMA) blends with 20 wt % poly(methyl methacrylate) (PMMA) droplets dispersed in a low‐density polyethylene (LDPE) matrix were studied. The HPB‐b‐PMMA pure diblock copolymer was prepared via controlled living anionic polymerization. Four copolymers, in terms of the molecular weights of the hydrogenated polybutadiene (HPB) and PMMA sequences (22,000–12,000, 63,300–31,700, 49,500–53,500, and 27,700–67,800), were used. We demonstrated with the stress–strain diagrams, in combination with scanning electron microscopy observations of deformed specimens, that the interfacial adhesion had a predominant role in determining the mechanism and extent of blend deformation. The debonding of PMMA particles from the LDPE matrix was clearly observed in the compatibilized blends in which the copolymer was not efficiently located at the interface. The best HPB‐b‐PMMA copolymer, resulting in the maximum improvement of the tensile properties of the compatibilized blend, had a PMMA sequence that was approximately half that of the HPB block. Because of the much higher interactions encountered in the PMMA phase in comparison with those in HPB (LDPE), a shorter sequence of PMMA (with respect to HPB but longer than the critical molecular weight for entanglement) was sufficient to favor a quantitative location of the copolymer at the LDPE/PMMA interface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 22–34, 2005     

Thermogravimetric characterisation of poly(methyl methacrylate) photopolymerised by colloidal cadmium sulphide

The thermal stability of poly(methyl methacrylate) (PMMA) photopolymerised using colloidal cadmium sulphide as the photoinitiator was studied by thermogravimetry (TG) and differential TG (DTG).The thermal stability of the CdS initiated PMMA was greater than that of conventional radically polymerised PMMA and approached that of anionically prepared PMMA. The DTG curve of the CdS initiated PMMA was a composite of four peaks, three of which correspond to the three peaks observed in the DTG curve of standard radically prepared PMMA. It is suggested that the additional peak arises from a new mode of depolymerisation initiation, that is, from chain end unsaturation introduced into the polymer chain during polymerisation initiation with the colloidal CdS.     

Nanosphere formation in copolymerization of methyl methacrylate with poly(ethylene glycol) macromonomers

Polymeric nanospheres consisting of poly(methyl methacrylate) (PMMA) cores and poly(ethylene glycol) (PEG) branches on their surfaces were prepared by free radical copolymerization of methyl methacrylate (MMA) with PEG macromonomers in ethanol/water mixed solvents. PEG macromonomers having a methacryloyl (MMA‐PEG) and p‐vinylbenzyl (St‐PEG) end group were used. It has become clear that the obtained polymer dispersions form three kinds of states, particle dispersion (milky solution), clear solution, and gel/precipitation. It was found that the reaction parameters such as MMA concentration, molecular weight, and concentration of PEG macromonomers, and water content can affect nanosphere formation in a copolymerization system. The water volume fraction of mixed ethanol/water solvents affected the particle size of the nanospheres. These differences in the formation of nanospheres were due to the solvophilic/solvophobic balance between the copolymers and solvents during the self‐assembling process of the copolymers. The sizes of nanospheres can be controlled by varying concentration of PEG macromonomer and water content in solvents. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1811–1817, 2000     

In situ synthesis of a novel transparent poly (methyl methacrylate) resin with markedly enhanced flame retardancy

A novel phosphorus‐containing monomer, (6‐oxido‐6H‐dibenzo[c,e][1,2]oxaphosphinin‐6‐yl)methyl acrylate (DOPO‐AA), is first synthesized and characterized by Fourier transform infrared spectra (FTIR), ¹H nuclear magnetic resonance (NMR) and ³¹P NMR. The monomer is then introduced into poly (methyl methacrylate) (PMMA) matrix via in situ copolymerization to produce a new PMMA based copolymer (PMMA/DOPO‐AA). From UV–vis spectra, microscale combustion calorimeter (MCC) and thermogravimetric analyses (TGA) results, the as‐fabricated PMMA/DOPO‐AA copolymers not only keep relatively high transparency, but also exhibit remarkable improvements in the flame retardancy and thermal stability, such as increased T_0.5 by 60.2°C and limited oxygen index (LOI) by 4.1, and decreased peak heat released rate (PHRR) by 34.7%. Thermal degradation behaviors investigated by real time Fourier transform infrared spectra (RTIR), char structure analysis studied by scanning electron microscope (SEM) and pyrolysis gaseous products studied by TGA coupled with FTIR (TGA‐FTIR) demonstrate that the catalytic charring function of DOPO‐AA in condensed phase and DOPO flame retardant systems in the gas phase are two key factors for the property enhancements. This work not only provides a promising flame‐retardant monomer for polymers, but also will stimulate more efforts on the development of DOPO‐containing flame‐retardant monomers. Copyright © 2015 John Wiley & Sons, Ltd.     

Structures and thermal properties of chitosan-modified poly(methyl methacrylate)

The emulsion polymerization of methyl methacrylate in the presence of chitosan with potassium persulfate (KPS) as an initiator was examined in a previous article. The free radicals that dissociated from KPS not only initiated the polymerization but also degraded the chitosan molecules. Therefore, in addition to its role as a cationic surfactant, chitosan also participated in the polymerization reaction. When the polymerization was complete, the latex polymer consisted of poly(methyl methacrylate) (PMMA) homopolymer and chitosan–PMMA copolymer. In this article, the structures and thermal properties of latex polymers are examined. Gel permeation chromatography was used to measure the molecular weight of the PMMA homopolymer, with the copolymer composition determined by an elemental analyzer. Scanning and transmission electronic microscopes were used to measure the size of latex particles from different reaction systems. The surface charges of latex particles at several different pH values were determined by the measurement of the ζ potential. All results agreed with the reaction mechanism proposed in the previous article. Finally, the presence of rigid chitosan increased the glass-transition temperature of the final latex polymers. Thermogravimetric analysis showed that the degradation behavior of latex polymers was similar to the unzipping mechanism of PMMA, yet the presence of chitosan units hindered the unzipping of the main chains in chitosan–PMMA copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1646–1655, 2001     

Methanol-induced opacity in poly (methyl methacrylate)

Methanol-induced opacity in poly (methyl methacrylate) (PMMA) is investigated subject to two cooling processes; furnace cooling and air cooling. The glass transition temperature of PMMA decreases with increasing time of exposure to methanol at 40–60°C and then increases during cooling, due to progressive desorption. Voids form during cooling as long as specimen temperature remains above its glass transition temperature. Since furnace cooling affords enough time for holes to expand larger than the light wavelengths, the transmittance of furnace-cooled PMMA is independent of wavelength. The transmittance of PMMA subjected to rapid cooling in the air is wavelength dependent due to scattering by holes smaller than light wavelengths. The transmittance of PMMA bearing a given weight gain of methanol (measured at absorption temperature) prior to cooling for furance cooling is lower than that for the same material subjected to air cooling. A sharp front between outer and inner regions is found in specimens removed quickly from the thermostated water bath to air at ambient temperature.     

Ionic conductivity and compatibility studies of blends of poly(methyl methacrylate) and poly(propylene glycol) complexed with LICF3SO3

Stable to atmospheric moisture, adhesive and transparent polymer electrolytes have been prepared by blending poly(methyl methacrylate) (PMMA) with poly(propylene glycol)-425/LiCF₃SO₃ complexes. The blending of the polymers has been achieved by a method developed in our laboratory: free radical polymerization of methylmethacrylate in the polyether/salt matrix. A series of polymer blend complexes varying in PMMA content (up to 20% by weight) and oxygen/metal ratios (25, 16, and 8) have been synthesized and their properties studied. All the samples prepared in this study were found to be optically clear unlike the higher molecular weight poly(propylene glycol)-2000 (PPG-2000) system which required a minimum salt concentration to compatibilize a specific amount of PMMA with PPG. The mechanisms by which the salt holds the otherwise incompatible polymers together in a single phase have been investigated by FT-IR. Our studies show a weak coupling of the ether oxygens in the PPG with the ester groups of the PMMA through the lithium cations. Discrete changes has been observed in the FT-IR spectrum of PMMA when doped with the lithium salt hitherto unnoticed with other dopants. Gel permeation chromatography results of the PMMA samples isolated from the solid electrolytes indicate the molecular weight to vary between 43000 and 121000 with relatively narrow distributions, 1.6?2.0. The ionic conductivities of the polymer blend electrolytes were fairly high (10^?5 S/cm) at room temperature. The PMMA neither significantly influenced the T_g of the blend complexes nor effected the ionic conductivities drastically. The ionic conductivity as a function of temperature followed the empirical Vogel-Tammann-Fulcher equation. The blending of PMMA with PPG/LiCF₃SO₃ complexes was found to impart good adhesiveness to the solid electrolytes while making them stable to atmospheric moisture. © 1992 John Wiley & Sons, Inc.     

Block copolymers of thiophene-capped poly(methyl methacrylate) with pyrrole

Poly(methyl methacrylate) with a thiophene end group having narrow polydispersity was prepared by the Atom Transfer Radical Polymerization (ATRP) technique. Subsequently, electrically conducting block copolymers of thiophene-capped poly(methyl methacrylate) with pyrrole were synthesized by using p-toluene sulfonic acid and sodium dodecyl sulfate as the supporting electrolytes via constant potential electrolysis. Characterization of the block copolymers were performed by CV, FTIR, SEM, TGA, and DSC analyses. Electrical conductivities were evaluated by the four-probe technique. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4218–4225, 1999     

Thermal crosslinking of poly(methyl methacrylate) by reaction of methyl ester and quaternary ammonium salt and application to (meth)acrylate-based TPEs

Copolymers of N-vinylbenzyl N-methyl pyrrolidinium chloride (VBMPC) and methyl methacrylate, PVBMPC-co-poly(methyl methacrylate) (PMMA), were synthesized by free-radical copolymerization and proved to be prone to crosslinking as a result of the reaction of methyl ester groups with benzyl methyl pyrrolidinium chloride (BMPC) moieties at temperatures higher than 110 °C. When the VBMPC content was lower than 20 wt %, these copolymers were miscible with homo-PMMA. Blends of homo-PMMA and PVBMPC-co-PMMA fully could be cured above 150 °C, when the molecular weight of PMMA exceeded 10,000 and the VBMPC content of the copolymer was higher than 5 wt %. This reaction was carried out to crosslink selectively the PMMA microdomains of PMMA-b-poly(isooctyl acrylate) (PIOA)-b-PMMA (MIM) triblock copolymers to explain the mechanism for the mechanical failure of fully (meth)acrylic thermoplastic elastomers. Comparison of the ultimate tensile properties of MIM block copolymers, when the dispersed PMMA phases and PIOA matrix were crosslinked, led to the conclusion that the ductile failure of the hard PMMA microdomains rather than the elastic failure of the PIOA matrix was the reason for the mechanical failure of MIM triblocks. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4402–4411, 1999     

Dynamic behavior of ultrahigh molecular weight poly(methyl methacrylate) in semidilute solutions

The paper presents some rheological investigations on ultrahigh molecular weight (u.h.m.w.) (M_w > 10⁷) poly(methyl methacrylate) in semidilute solutions. The main interest was to study the viscoelastic behavior of the semidilute solutions at different concentrations and temperatures. In the 60‐600 rad/s frequency range, the experimental data show a predominantly elastic response (G′ > G″) for the long poly(methyl methacrylate) chains in toluene.