Preparation of microcellular polypropylene/polystyrene blend foams with tunable cell structure

By using supercritical carbon dioxide (sc‐CO₂) as the physical foaming agent, microcellular foaming was carried out in a batch process from a wide range of immiscible polypropylene/polystyrene (PP/PS) blends with 10–70 wt% PS. The blends were prepared via melt processing in a twin‐screw extruder. The cell structure, cell size, and cell density of foamed PP/PS blends were investigated and explained by combining the blend phase morphology and morphological parameters with the foaming principle. It was demonstrated that all PP/PS blends exhibit much dramatically improved foamability than the PP, and significantly decreased cell size and obviously increased cell density than the PS. Moreover, the cell structure can be tunable via changing the blend composition. Foamed PP/PS blends with up to 30 wt% PS exhibit a closed‐cell structure. Among them, foamed PP/PS 90:10 and 80:20 blends have very small mean cell diameter (0.4 and 0.7 µm) and high cell density (8.3 × 10¹¹ and 6.4 × 10¹¹ cells/cm³). Both of blends exhibit nonuniform cell structure, in which most of small cells spread as “a string of beads.” Foamed PP/PS 70:30 blend shows the most uniform cell structure. Increase in the PS content to 50 wt% and especially 70 wt% transforms it to an irregular open‐cell structure. The cell structure of foamed PP/PS blends is strongly related to the blend phase morphology and the solubility of CO₂ in PP more than that in PS, which makes the PP serve as a CO₂ reservoir. Copyright © 2009 John Wiley & Sons, Ltd.     

Ion‐beam‐induced morphology on the surface of thin polymer films at low current density and high ion fluence

The effect of Xe⁺ bombardment on the surface morphology of four different polymers, polystyrene (PS), poly(phenylene oxide), polyisobutylene, and polydimethylsiloxane, was investigated in ion energy and fluence ranges of interest for secondary ion mass spectrometry depth‐profiling analysis. Atomic force microscopy (AFM) was applied to analyze the surface topography of pristine and irradiated polymers. AFM analyses of nonirradiated polymer films showed a feature‐free surface with different smoothness. We studied the influence of different Xe⁺ beam parameters, including the incidence angle, ion energy (660–4000 eV), current density (0.5 × 10² to 8.7 × 10² nA/cm²), and ion fluence (4 × 10¹⁴ to 2 × 10¹⁷ ion/cm²). Xe⁺ bombardment of PS with 3–4 keV at a high current density did not induce any change in the surface morphology. Similarly, for ion irradiation with lower energy, no surface morphology change was found with a current density higher than 2.6 × 10² nA/cm² and an ion fluence up to 4 × 10¹⁶ ion/cm². However, Xe⁺ irradiation with a lower current density and a higher ion fluence led to topography development for all of the polymers. The roughness of the polymer surface increased, and well‐defined patterns appeared. The surface roughness increased with ion irradiation fluence and with the decrease of the current density. A pattern orientation along the beam direction was visible for inclined incidence between 15° and 45° with respect to the surface normal. Orientation was not seen at normal incidence. The surface topography development could be explained on the basis of the balance between surface damage and sputtering induced by the primary ion beam and redeposition–adsorption from the gas phase. Time‐of‐flight secondary ion mass spectrometry analyses of irradiated PS showed strong surface modifications of the molecular structure and the presence of new material. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 314–325, 2001     

Evaluation of antithrombogenicity of ion‐implanted silicone rubber

Ion implantations into silicone rods were performed at 150 keV with doses ranging from 1 × 10⁷ to 3 × 10¹⁷ ions/cm². The antithrombogenicity was tested by the superior vena cava (SVC) indwelling method for two days in rats with ¹¹¹In‐tropolone ‐ platelets, and by the inferior vena cava (IVC) indwelling method. Results of the SVC indwelling method showed that platelet accumulation on ion ‐ implanted specimens decreased. Macroscopic views of the ion‐implanted IVC specimens in dogs revealed little thrombus formation. In particular, SVC indwelling method revealed that O₂⁺, K⁺ and Kr⁺ (1 × 10¹⁷ ions/cm²) implantation was most effective in reducing platelet accumulation. Copyright © 1999 John Wiley & Sons, Ltd.     

Foaming behavior of polypropylene/polystyrene blends enhanced by improved interfacial compatibility

A series of polypropylene (PP)/polystyrene (PS) blends were prepared by solvent blending with PS‐grafted PP copolymers (PP‐g‐PS) having different PS graft chain length as compatibilizers. The interfacial compatibility was significantly improved with increasing PS graft chain length until the interface was saturated at PS graft chain length being 3.29 × 10³ g/mol. The blends were foamed by using pressure‐quenching process and supercritical CO₂ as the blowing agent. The cell preferentially formed at compatibilized interface because of low energy barrier for nucleation. Combining with the increased interfacial area, the compatibilized interface lead to the foams with increased cell density compared to the uncompatibilized one. The increase in interfacial compatibility also decreased the escape of gas, held more gas for cell growth, and facilitated the increase in expansion ratio of PP/PS blend foams. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1641–1651, 2008     

Patterning of cells on a PVC film surface functionalized by ion irradiation

Micropatterns of cells on a poly(vinyl chloride) (PVC) film surface were created by using ion irradiation. A PVC film was irradiated with H⁺ ions through a pattern mask in order to create patterns of the hydrophilic/hydrophobic regions on the PVC surface. The effect of ion irradiation on the surface properties of the PVC film was characterized by using Fourier transform‐infrared spectroscopy (FT‐IR), water contact angle measurement, and X‐ray photoelectron spectroscopy (XPS). The results revealed that the chemical environment of the PVC film surface was effectively changed by ion irradiation due to dehydrochlorination and oxidation. The in vitro cell culture on the patterned PVC film surface showed selective adhesion and proliferation of the cells on the ion‐irradiated regions. Well‐defined 50 µm patterns of the cells were obtained on the PVC film surface irradiated to 1 × 10¹⁵ ions/cm². Copyright © 2009 John Wiley & Sons, Ltd.     

Poly(2‐oxazoline)‐derived Contact Biocides: Contributions to the Understanding of Antimicrobial Activity

A set of poly(2‐oxazoline)‐derived (co‐)polymers was prepared by microwave‐assisted polymerizations and acid‐mediated hydrolysis and tested for antimicrobial activity in 50 × 50 × 2 mm PP compound plates containing 5 wt% of the polymers. Antimicrobial activity against gram‐negative E. coli and P. aeruginosa as well as C. albicans depended only on the degree of hydrolysis, while antimicrobial activity against gram‐positive S. aureus was only observed for hydrolyzed poly(2‐nonyl‐2‐oxazoline)s. The surface energies of the compound plates compared to pure PP were hardly altered, and the compounds can be considered as alternatives for PP. The presence of the biocide additives at the surface of the PP compound plates could be shown by combined ATR‐IR, zeta potential, and SEM‐EDX measurements. Antimicrobial activity was maintained during double incubation as well as for lowered amounts of the biocide additive of 1% in PP compound plates.

     

Degradation of poly(acrylates) under SF5+ primary ion bombardment studied using time‐of‐flight secondary ion mass spectrometry. 2. Poly(n‐alkyl methacrylates)

Polyatomic primary ions offer low penetration depth and high damage removal rates in some polymers, facilitating their use in the molecular depth profiling of these polymers by secondary ion mass spectrometry (SIMS). This study is the second in a series of systematic characterizations of the effect of polymer chemistry on degradation under polyatomic primary ion bombardment. In this study, time‐of‐flight SIMS (ToF‐SIMS) was used to measure the damage of ～90 nm thick spin‐cast poly(methyl methacrylate), poly(n‐butyl methacrylate), poly(n‐octyl methacrylate) and poly(n‐dodecyl methacrylate) films under extended (～2 × 10¹⁴ ions cm^?2) 5 keV SF₅⁺ bombardment. The degradation of the poly(n‐alkyl methacrylates) were compared to determine the effect of the length of the alkyl pendant group on their degradation under SF₅⁺ bombardment. The sputter rate and stability of the characteristic secondary ion intensities of these polymers decreased linearly with alkyl pendant group length, suggesting that lengthening the n‐alkyl pendant group resulted in increased loss of the alkyl pendant groups and intra‐ or intermolecular cross‐linking under SF₅⁺ bombardment. These results are partially at variance with the literature on the thermal degradation of these polymers, which suggested that these polymers degrade primarily via depolymerization with minimal intra‐ or intermolecular cross‐linking. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis of graft polymers with poly(isoprene) as main chain by living anionic polymerization mechanism

The graft polymers [poly(isoprene)‐graft‐poly(styrene)] (PI‐g‐PS), [poly(isoprene)‐graft‐poly(isoprene)] (PI‐g‐PI), [poly(isoprene)‐graft‐(poly(isoprene)‐block‐poly(styrene))] PI‐g‐(PI‐b‐PS), and [poly(isoprene)‐graft‐(poly(styrene)‐block‐poly(isoprene))] PI‐g‐(PS‐b‐PI) with PI as main chain were synthesized through living anionic polymerization (LAP) mechanism and the efficient coupling reaction. First, the PI was synthesized by LAP mechanism and epoxidized in H₂O₂/HCOOH system for epoxidized PI (EPI). Then, the graft polymers with controlled molecular weight of main chain and side chains, and grafting ratios were obtained by coupling reaction between PI^?Li⁺, PS^?Li⁺, PS‐b‐PI^?Li⁺, or PI‐b‐PS^?Li⁺ macroanions and the epoxide on EPI. The target polymers and all intermediates were well characterized by SEC,¹H NMR, as well as their thermal properties were also evaluated by DSC. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Surface properties of polymers treated with F2 laser

Selected polymers (polyethylene‐PE, polypropylene‐PP, polytetrafluoroethylene‐PTFE, polystyrene‐PS and polyethylenterephthalate‐PET) were irradiated with the linearly polarized light of a pulsed 157 nm F₂ laser. The irradiation results in degradation of polymers and ablation of polymer surfaces. Contact angle, measured by goniometry, was studied as a function of the number of laser pulses. The volume of the ablated polymer layer was determined by gravimetry. Changes in surface morphology and roughness were observed using atomic force microscopy. Surface chemistry of the samples was investigated by electrokinetic analysis and by XPS. While PET and PE exhibit small ablation, the ablation of PS and PTFE is more significant, and the most pronounced ablation is observed on PP. Contact angle of all polymers, with the only exception of PP, is a decreasing function of the number of laser pulses up to 2000 pulses. Laser irradiation leads to a refinement of the polymer surface morphology and a decrease of their surface roughness. Electrokinetic analysis and PS show changes in the surface chemistry of polymers after the laser treatment. Copyright © 2011 John Wiley & Sons, Ltd.     

Degradation of poly(acrylates) under SF5+ primary ion bombardment studied using time‐of‐flight secondary ion mass spectrometry. 3. Poly(hydroxyethyl methacrylate) with chemical derivatization

Molecular depth profiling of polymers by secondary ion mass spectrometry (SIMS) has focused on the use of polyatomic primary ions due to their low penetration depth and high damage removal rates in some polymers. This study is the third in a series of systematic characterizations of the effect of polymer chemistry on degradation under polyatomic primary ion bombardment. In this study, time‐of‐flight SIMS (ToF‐SIMS) was used to assess 5 keV SF₅⁺‐induced damage of ～90 nm thick spin‐cast poly(2‐hydroxyethyl methacrylate) (PHEMA) and ～130 nm thick trifluoroacetic anhydride‐derivatized PHEMA (TFAA‐PHEMA) films. The degradation of these polymers under extended SF₅⁺ bombardment (～2 × 10¹⁴ ions cm^?2) was compared to determine the effect of the pendant group chemistry on their degradation. The sputter rate and ion‐induced damage accumulation rate of PHEMA were similar to a poly(n‐alkyl methacrylate) of similar pendant group length, suggesting that the addition of a terminal hydroxyl group to the alkyl pendant group does not markedly change the stability of poly(n‐alkyl methacrylates) under SF₅⁺ bombardment. The sputter rate and ion‐induced damage accumulation rate of TFAA‐PHEMA were much higher than a poly(n‐alkyl methacrylate) of similar pendant group length, suggesting that derivatization of the terminal hydroxyl group can significantly reduce degradation of the polymer under SF₅⁺ bombardment. This result is in good agreement with the literature on the thermal and radiation‐induced degradation of fluorinated poly(alkyl methacrylates), which suggests that the electron‐withdrawing fluorinated pendant group increases the probability of depolymerization. Copyright © 2004 John Wiley & Sons, Ltd.     

Conductive and optical properties of PPV modified by N+ ion implantation

In this article, a soluble poly[2‐methoxy‐5‐(3′‐methyl)butoxy]‐p‐phenylene vinylene (MMB‐PPV) was synthesized by dehydrochlorination reaction and the MMB‐PPV film was implanted by nitrogen ions (N⁺) with the ion dose and energy in the range of 3.8 × 10¹⁵ to 9.6 × 10¹⁶ ions/cm² and 15–35 keV, respectively. The surface conductivity, optical absorption, optical band gap (E_g) of modified MMB‐PPV film were studied, and the third‐order nonlinear optical susceptibility (χ⁽³⁾) as well as its environmental stability of modified MMB‐PPV film were also measured by degenerate four‐wave mixing system. The results showed that the surface conductivity of MMB‐PPV film was up to 3.2 × 10^?2 S when ion implantation was performed with the energy of 35 keV at an ion dose of 9.6 × 10¹⁶ ions/cm², which was seven order of magnitude higher than that of the pristine film. UV‐Vis absorption spectra demonstrated that the optical absorption of MMB‐PPV film was enhanced gradually in the visible region followed by a red shift of optical absorption threshold and the E_g value was reduced from 2.12 eV to 1.59 eV with the increase of ion dose and energy. The maximum χ⁽³⁾ value of 2.45 × 10^?8 esu for modified MMB‐PPV film was obtained with the ion energy of 20 keV at an ion dose of 3.8 × 10¹⁶ ions/cm², which was almost 33 times larger than that for pristine film. In comparison to the reduction of 17% in the χ⁽³⁾ value of pristine MMB‐PPV film, the maximum χ⁽³⁾ value of 2.45 × 10^?8 esu for modified MMB‐PPV film decreased by over 5.3% when they had been exposed under the same ambient conditions for 90 days. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 2072–2077, 2010     

Modifications of polypropylene surface properties by He+ ion implantation

A polypropylene (PP) modified by ethylene–propylene rubber (EPR) was treated in vacuo by α particles (with an energy of 400 keV) with fluences that varied from 10¹¹ to 10¹⁶ He⁺ cm^?2. Samples were investigated with attenuated total reflection Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, contact‐angle measurements, differential scanning calorimetry, swelling, nanoindentation, and friction techniques. After treatment, new chemical groups (carbonyl and vinyl bonds) appeared at the PP/EPR surface. These chemical modifications led to changes in the surface free energy of PP/EPR. Irradiation also modified the PP/EPR structure because crosslinking occurred after treatment for fluences above or equal to 5 × 10¹⁴ He⁺ cm^?2. Moreover, the PP melting temperature and enthalpy were greatly decreased for fluences above or equal to 10¹⁴ He⁺ cm^?2. The surface mechanical properties were also changed after treatment. Indeed, the friction coefficient decreased, whereas the hardness and Young's modulus drastically increased, after irradiation at higher fluences. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1183–1191, 2003     

Focused ion beam implantation of Ga in Si and Ge: fluence‐dependent retention and surface morphology

Focused ion beam implantation of 30‐keV Ga⁺ ions in single‐crystalline Si and Ge was investigated by SIMS, using Cs⁺ primary ions for sputtering. Nine different implantation fluences ranging from 1 × 10¹³ to 1 × 10¹⁷ Ga⁺‐ions/cm² were used, with implanted areas of 40 × 40 µm². The Ga concentration distributions of these implants were determined by SIMS depth profiling. Such 30‐keV Ga implantations were also simulated by a dynamic Monte‐Carlo code that takes into account the gradual change of the near‐surface composition due to the Ga incorporation. In both approaches, an essentially linear increase of the Ga peak concentrations with fluence is found up to ～1 × 10¹⁶cm^?2; for higher fluences, the Ga content approaches a saturation level which is reached at about (1–2) × 10¹⁷cm^?2. The measured and simulated peak concentrations of the Ga distributions are in good agreement. The most probable ranges obtained from the experiments correspond closely with the respective values from the simulations. The surface morphology caused by Ga⁺ implantation was investigated by atomic force microscopy (AFM). The AFM data indicate that for low fluences (<3 × 10¹⁵cm^?2) the surface within the implanted areas is growing outward (i.e. is swelling). For increasingly higher fluences, sputter‐induced erosion of the surface becomes dominant and distinct craters are formed for fluences above ～1 × 10¹⁶cm^?2. At the boundary of the implanted region a wall‐like structure is found to form upon Ga implantation; its height is growing with increasing fluence, reaching a value of ～15 nm at 1 × 10¹⁷ Ga⁺‐ions/cm². Copyright © 2008 John Wiley & Sons, Ltd.     

Chemically modified porous silicon for laser desorption/ionization mass spectrometry of ionic dyes

Desorption/ionization on silicon (DIOS) mass spectra of model ionic dyes methylene blue (MB⁺Cl^?) and methyl orange (Na⁺MO^?) were studied using p⁺ type‐derived porous silicon (PS) free layers. As‐prepared PS (PS‐H), the PS thermally oxidized at 300 °C (PS‐OX), PS with chemically grafted cation‐exchanging alkylsulfonic acid (PS‐SO₃H) and anion‐exchanging propyl‐octadecyldimethylammonium chloride (PS‐ODMA⁺Cl^?) groups was tested as ionization platforms. Two mechanisms of the methylene blue desorption/ionization were found: (1) the formation of [MB + H]^+? ion due to the reduction/protonation of MB⁺, which is predominant for PS‐H and PS‐OX platforms and (2) direct thermal desorption of the MB⁺ cation, prevailing for PS‐SO₃H. The fragmentation of the cation is significantly suppressed in the latter case. The samples of PS‐SO₃H and PS‐ODMA⁺ Cl^? efficiently adsorb the dyes of the opposite charge from their solutions via the ion‐exchange. Consequent DIOS MS studies allow to detect only low fragmented ions (MB⁺ and MO^?, respectively), demonstrating the potential of the ion‐exchange adsorption combined with DIOS MS for the analysis of ionic organic compounds in solutions. Copyright © 2009 John Wiley & Sons, Ltd.     

Transition and relaxation processes of polyethylene,polypropylene, and polystyrene studied by positron annihilation

Transition and relaxation processes of polyethylene (PE), polypropylene (PP), and polystyrene (PS) were studied by the positron annihilation technique. From measurements of lifetime spectra of positrons as a function of temperature, the lifetime of ortho-positronium, τ₃, and its intensity, I₃, were found to increase above 260 K for PP. This fact was attributed to a cooperative motion of large segments of molecules above the glass transition temperature, T_g. For PE, above T_g (140 K), the value of τ₃ increased, but the temperature coefficient of I₃ was negative below 230 K. From this fact, for PE, the molecular motions that cause the glass transition were associated with a rearrangement of molecules by local motions such as kink motions. The discrepancy between the results for PE and PP was attributed to the presence of methyl groups in PP and the resultant suppression of the local motions. For PS (T_g = 340 K), the molecular motions were found to start above 260 K, but those were suppressed by an interphenyl correlation. Detailed annihilation characteristics of positrons in polymers were also discussed. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1601–1609, 1997     

A novel poly(p‐phenylene) containing alternating poly(perfluorooctylethyl acrylate‐co‐methyl methacrylate) and polystyrene grafts by combination of atom transfer radical polymerization and Suzuki coupling processes

A poly(p‐phenylene) (PP), carrying perfectly alternating, well‐defined poly(perfluorooctylethyl acrylate‐co‐methyl methacrylate) [P(FEA‐co‐MMA)] and polystyrene (PS) side chain grafts, was synthesized by the combination of atom transfer radical polymerization (ATRP) and Suzuki cross‐coupling processes. First, dibromobenzene and diboronic ester functional macromonomers of P(FEA‐co‐MMA) and PS, respectively, were prepared by ATRP. In the second step, PP with lateral alternating P(FEA‐co‐MMA) and PS chains was synthesized by a Suzuki coupling reaction in the presence of Pd(PPh₃)₄ catalyst. The wetting behavior of the polymers was studied by measurements of the static contact angle θ of thin films (200?400 nm thickness) using water and n‐hexadecane as wetting liquids. The obtained fluorinated PP showed high static contact angles with both interrogating liquids, exhibiting simultaneously hydrophobic (θ_w = 111°) and lipophobic (θ_h = 67°) properties. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Surface modification of polymers. IV. UV initiated degradation of polymers with stabilizers grafted onto the surface

Polypropylene (PP), Polyethylene (PE), and polystyrene (PS) films were grafted with glycidylmethacrylate in thin surface layers. To the oxiran groups thus grafted onto the surface three UV stabilizers were attached, 4-amino-2,2,6,6-tetramethylpiperidine (AP), 2,4-dihydroxybenzophenone (DHBP), and phenyl 4-aminosalicylate (PAS). The amount of stabilizer grafted onto the surface varied between 25 and 40 nmol/cm² depending on the polymer substrate. The samples were exposed to UV radiation in air, and the degradation and oxidation of the polymers were studied with IR, UV, and ESCA spectroscopy and by stress–strain measurements. PP grafted with AP exhibited a near 20-fold increase in lifetime compared with the unprotected PP, AP did not stabilize the PE or PS samples. DHBP was an efficient stabilizer of PE, the oxidation rate of the grafted sample being 1/2 to 1/3 of the ungrafted. A similar effect was observed when DHBP was grafted onto PP and PS. PAS underwent a rearrangement reaction when irradiated with UV light, and had only a slight stabilizing effect.     

Ion induced controlled modifications in structural and optical properties of indium oxide thin films – studies with 25‐keV Co− and N+ beam implantations

Two sets of indium oxide thin films (~150 nm) grown on quartz substrates using thermal evaporation technique were processed separately with 25‐keV Co^? and N⁺ ions with several fluences ranging from 1.0 × 10¹⁵ to 1.0 × 10¹⁶ ions/cm². The pristine and the ion implanted films were characterized by Rutherford backscattering spectroscopy (RBS), X‐ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV–Vis spectrometry. The RBS spectra reveal signature of only cobalt and nitrogen in accordance to their fluences confirming absence of any contamination arising due to ion implantation. An increase in the average crystallite size (from 13.7 to 15.3 nm) of Co^? ions implanted films was confirmed by XRD. On the other hand, the films implanted with N⁺ ions showed a decrease in the average crystallite size from 20.1 to 13.7 nm. The XRD results were further verified by SEM micrographs. As seen in AFM images, the RMS surface roughness of the samples processed by both ion beams was found to decrease a bit (29.4 to 22.2 nm in Co^? implanted samples and 24.2 to 23.3 nm in N⁺ implanted samples) with increasing fluence. The Tauc's plot deduced from UV–visible spectroscopy showed that the band gap decreases from 3.54 to 3.27 eV in Co^? implanted films and increases from 3.38 to 3.58 eV for films implanted with N⁺ ions. The experimental results suggest that the modifications in structural and optical properties of indium oxide films can be controlled by optimizing the implantation conditions. Copyright © 2017 John Wiley & Sons, Ltd.     

Brush‐First ROMP of poly(ethylene oxide) macromonomers of varied length: impact of polymer architecture on thermal behavior and Li+ conductivity

The properties of polymeric materials are dictated not only by their composition but also by their molecular architecture. Here, by employing brush‐first ring‐opening metathesis polymerization (ROMP), norbornene‐terminated poly(ethylene oxide) (PEO) macromonomers ( MM‐n , linear architecture), bottlebrush polymers ( Brush‐n , comb architecture), and brush‐arm star polymers ( BASP‐n , star architecture), where n indicates the average degree of polymerization (DP) of PEO, are synthesized. The impact of architecture on the thermal properties and Li⁺ conductivities for this series of PEO architectures is investigated. Notably, in polymers bearing PEO with the highest degree of polymerization, irrespective of differences in architecture and molecular weight (~100‐fold differences), electrolytes with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as an Li⁺ source exhibit normalized ionic conductivities (σ_n) within only 4.9 times difference (σ_n = 29.8 × 10^?5 S cm^?1 for MM‐45 and σ_n = 6.07 × 10^?5 S cm^?1 for BASP‐45 ) at a concentration of Li⁺ r = [Li⁺]/[EO] = 1/12 at 50 °C. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 448–455     

Surface characterization of ion-implanted polyethylene

Polyethylene (PE) film was implanted with 1000-keV Ar⁺ ions to a fluence of 5 × 10¹⁴ ions/cm² under high vacuum conditions (2.5 × 10⁻⁶ torr) and the film surface was investigated by means of microhardness and microwear measurements, and FTIR/ATR, Raman, and XPS techniques. Ion implantation significantly increased the subsurface hardness and also significantly improved the microwear resistance of the polymer. The implanted surface region of the film was found to consist of two distinct layers. One was the outermost carbon layer with a thickness of the order of 10 nm. In this layer, ca. 75% of carbon atoms were combined by graphitic sp² and diamond-like sp³ bonds, and the remaining 25% had chemical links with oxygen atoms. Spectroscopic data suggested that the sp²-bonded carbons segregated in graphite-like clusters containing imbedded oxygen atoms, interconnected by the sp³-bonded carbons. The other was the subsurface layer resulting from PE oxidation after ion-beam treatment. This layer was characterized by high contents of O H and CO groups as well as ester and double bonds. The chemical composition of the layer was uniform and did not vary over the layer thickness of about 1.4 μm. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 715–725, 1998