Crystallization studies of poly(trimethylene terephthalate) using thermal analysis and far‐infrared spectroscopy

Crystallization of poly(trimethylene terephthalate) (PTT) by annealing was examined using density measurement, differential scanning calorimetry, and far‐infrared spectroscopy (FIR). Crystallinity, measured by density, increased slowly up to the T_a of 185 °C and increases rapidly once T_a exceeds 185 °C. It was found that thermally induced crystallization is mainly temperature‐dependent above T_a = 185 °C and temperature‐ and time‐dependent below T_a = 60 °C. Two melting transitions, T and T, were observed for those samples annealed above 120 °C. No significant change in T was observed as a function of T_a while T showed strong dependency on T_a. Digital subtraction of the amorphous contribution from the semicrystalline FIR spectra provided characteristic spectra of amorphous and crystalline PTT. The bands at 373, 282, and 92 cm^?1 were assigned to the crystalline phase, while the bands at 525, 406, and 351 cm^?1 were attributed to the amorphous phase. It was shown that FIR spectroscopy can be used as a means to estimate the degree of crystallinity of PTT. The band ratio of 373 and 501 cm^?1 was plotted against crystallinity measured by density and reasonably good correlation was obtained. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1675–1682, 2007     

Linear versus nonlinear determinations of equilibrium melting temperatures of poly(trimethylene terephthalate) and miscible blend with poly(ether imide) exhibiting multiple melting peaks

Multiple melting peaks in some semicrystalline polymers such as poly(trimethylene terephthalate) (PTT) have caused some difficulty in estimating accurately the equilibrium melting points. PTT forms a miscible blend with amorphous poly(ether imide) (PEI); for comparison purposes, a miscible system of a fixed composition (PTT/PEI of weight ratio = 9/1) was determined. PTT and its miscible blend both exhibited dual melting peaks (labeled as low and high peaks: T_m,L, T_m,H), and the first peaks (T_m,L), not the second peak (T_m,H), should be used for extrapolation. The equilibrium melting temperatures (T) of neat PTT and its blend PTT/PEI (9/1) were 245.2 and 242.4 °C, respectively, by the linear Hoffman–Weeks treatment using the corrected values of T_m,L (i.e., values obtained using a heating rate close to zero). Linear and nonlinear treatments led to a significant difference in estimated T, and the relative validity of these two methods is discussed. The nonlinear estimate yielded a higher value by about 27.3 °C for neat PTT and 23.1 °C for the PTT/PEI (9/1) blend, respectively (also the correction in T_m,L at the same condition mentioned previously). Results showed melting depression in miscible PTT/PEI (9/1). In addition, the T value of neat PTT was higher than that of PTT/PEI (9/1) owing to much thicker and more‐perfect crystals in neat PTT. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1571–1581, 2002     

Depolymerization kinetics of di(4‐tert‐butyl cyclohexyl) itaconate and Mark‐Houwink‐Kuhn‐Sakurada parameters of di(4‐tert‐butyl cyclohexyl) itaconate and di‐n‐butyl itaconate

Multipulse pulsed laser polymerization coupled with size exclusion chromatography (MP‐PLP‐SEC) has been employed to study the depropagation kinetics of the sterically demanding 1,1‐disubstituted monomer di(4‐tert‐butylcyclohexyl) itaconate (DBCHI). The effective rate coefficient of propagation, k, was determined for a solution of monomer in anisole at concentrations, c, 0.72 and 0.88 mol L^?1 in the temperature range 0 ≤ T ≤ 70 °C. The resulting Arrhenius plot (i.e., ln k vs. 1/RT) displayed a subtle curvature in the higher temperature regime and was analyzed in the linear part to yield the activation parameters of the forward reaction. In the temperature region where no depropagation was observed (0 ≤ T ≤ 50 °C), the following Arrhenius parameters for k_p were obtained (DBCHI, E_p = 35.5 ± 1.2 kJ mol^?1, ln A_p = 14.8 ± 0.5 L mol^?1 s^?1). In addition, the k data was analyzed in the depropagatation regime for DBCHI, resulting in estimates for the associated entropy (?ΔS = 150 J mol^?1 K^?1) of polymerization. With decreasing monomer concentration and increasing temperature, it is increasingly more difficult to obtain well structured molecular weight distributions. The Mark Houwink Kuhn Sakurada (MHKS) parameters for di‐n‐butyl itaconate (DBI) and DBCHI were determined using a triple detection GPC system incorporating online viscometry and multi‐angle laser light scattering in THF at 40 °C. The MHKS for poly‐DBI and poly‐DBCHI in the molecular weight range 35–256 kDa and 36.5–250 kDa, respectively, were determined to be K_DBI = 24.9 (10³ mL g^?1), α_DBI = 0.58, K_DBCHI = 12.8 (10³ mL g^?1), and α_DBCHI = 0.63. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1931–1943, 2007     

Isothermal crystallization behavior of poly(L‐lactide) in poly(L‐lactide)‐block‐poly(ethylene glycol) diblock copolymers

The crystal unit‐cell structures and the isothermal crystallization kinetics of poly(L ‐lactide) in biodegradable poly(L ‐lactide)‐block‐methoxy poly(ethylene glycol) (PLLA‐b‐MePEG) diblock copolymers have been analyzed by wide‐angle X‐ray diffraction and differential scanning calorimetry. In particular, the effects due to the presence of MePEG that is chemically connected to PLLA as well as the PLLA crystallization temperature T_C are examined. Though we observe no variation of both the PLLA and MePEG crystal unit‐cell structures with the block ratio between PLLA and MePEG and T_C, the isothermal crystallization kinetics of PLLA is greatly influenced by the presence of MePEG that is connected to it. In particular, the equilibrium melting temperature of PLLA, T, significantly decreases in the diblock copolymers. When the T_C is high so that the crystallization is controlled by nucleation, because of the decreasing T and thereafter the nucleation density with decreasing PLLA molecular weight, the crystallinity of PLLA also decreases with a decrease in the PLLA molecular weight. While, for the lower crystallization temperature regime controlled by the growth mechanism, the crystallizability of PLLA in copolymers is greater than that of pure PLLA. This suggests that the activation energy for the PLLA segment diffusing to the crystallization site decreases in the diblocks. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2438–2448, 2006     

Viscosity of poly(vinyl acetate) and its concentrated solutions

Data on the viscosity of poly(vinyl acetate) (PVOAc) and its concentrated solutions in diethyl phthalate (DEP) and cetyl alcohol (CeOH) are examined over the molecular weight range 8 × 10³ < M < 1.3 × 10⁶, the range 0.15 < φ < 1.0 of the volume fraction φ of polymer, the temperature range 308 to 430°K for PVOAc and its solutions in DEP, and at 396°K in CeOH. The latter is the θ temperature for dilute solutions of PVOAc in CeOH. The data are analyzed with the relation η = KX_c(αφM/M_c)^a exp[1/β(T – T₀)], where a is 1 or 3.4 for αφM less than or greater than a constant M_c, respectively, and X_C, is a constant. The expansion factor α_φ of the chain dimension is found to be essentially unity for φ > ca. 0.25, increasing with decreasing φ for smaller φ. Both β and T₀ depend on φ, and T₀ also depends on M at low M.     

Novel thermoplastic elastomers. III. Synthesis,characterization, and properties of star‐block copolymers of poly(indene‐b‐isobutylene) arms emanating from cyclosiloxane cores

Novel thermoplastic elastomers (TPEs) consisting of poly(isobutylene‐b‐indene) (PIB‐b‐PInd) arms radiating from hexamethylcyclohexasiloxane (D) cores were prepared, characterized, and their properties investigated. The syntheses of these star‐blocks involved the linking by hydrosilation of PInd‐b‐PIB CH₂ CHCH₂ prearms to D. The prearms were obtained by initiating the living polymerization of Ind by the cumyl chloride (CumCl)/TiCl₄ or cumyl methoxide (CumOMe)/TiCl₄ systems, continuing by the sequential block copolymerization of IB, and concluding the synthesis by end quenching with allyltrimethylsilane (ATMS). Dedicated experiments were carried out to develop conditions for the various synthesis steps. Select mechanical, thermal, and rheological properties of TPE star‐blocks having 5–18 PInd‐b‐PIB arms have been investigated. Because of the high T_g of the glassy PInd segment (T_g,PInd = 170–220°C), these TPEs maintained their strength at higher temperatures than those of similar polystyrene‐based star blocks. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 279–290, 2000     

Melting studies of poly(vinylidene fluoride) and its blends with poly(methyl methacrylate)

Blends of poly(vinylidene fluoride) (PVF₂) and poly(methyl methacrylate) exhibit complex melting behavior when crystallized at low undercoolings. Three crystals comprised of two different PVF₂ forms grow. Hoffman-Weeks plots of the observed melting points T_m of these crystals versus crystallization temperatures are constructed. The lowest-melting-point species, the α form, shows a change in slope which is attributed to fewer head-to-head PVF₂ units trapped in the crystal at higher temperatures. Defect energies in the crystal due to these units are calculated to be from 6.3 to 10.3 kJ/mol. Estimating lamellar thicknesses from the slopes of the two regions gives much more reasonable values when the high-temperature data are used. Removal of kinetic effects that lower the observed T_m by extrapolating the data to obtain T permits the thermodynamic interaction energy density B between the two polymers to be obtained. The low-temperature α-form data give B = ?8.83 × 10⁶ J/m³. The high-temperature α-form data and the T of the γ-form crystals both show B to vary from ?5.40 × 10⁶ to ?2.96 × 10⁷ J/m³ as the blend composition goes from 40.1 vol % to pure PVF₂.     

Synthesis and characterizations of well‐defined branched polymers with AB2 branches by combination of RAFT polymerization and ROP as well as ATRP

A well‐defined branched copolymer with PLLA‐b‐PS₂ branches was prepared by combination of reversible addition‐fragmentation transfer (RAFT) polymerization, ring‐opening polymerization (ROP), and atom transfer radical polymerization (ATRP). The RAFT copolymerization of methyl acrylate (MA) and hydroxyethyl acrylate (HEA) yielded poly(MA‐co‐HEA), which was used as macro initiator in the successive ROP polymerization of LLA. After divergent reaction of poly(MA‐co‐HEA)‐g‐PLLAOH with divergent agent, the macro initiator, poly(MA‐co‐HEA)‐g‐PLLABr₂ was formed in high conversion. The following ATRP of styrene (St) produced the target polymer, poly(MA‐co‐HEA)‐g‐(PLLA‐b‐PS₂). The structures, molecular weight, and molecular weight distribution of the intermediates and the target polymers obtained from every step were confirmed by their ¹H NMR and GPC measurements. DSC results show one T = 3 °C for the poly(MA‐co‐HEA), T = ?5 °C, T= 122 °C, and T = 157 °C for the branched copolymers (poly(MA‐co‐HEA)‐g‐PLLA), and T = 51 °C, T = 116 °C, and T = 162 °C for poly(MA‐co‐HEA)‐g‐(PLLA‐b‐PS₂). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 549–560, 2006     

Effects of lithium salt and poly(4‐vinyl phenol) on crystalline and amorphous phases in poly(ethylene oxide)

Effects of a strong‐interacting amorphous polymer, poly(4‐vinyl phenol) (PVPh), and an alkali metal salt, lithium perchlorate (LiClO₄), on the amorphous and crystalline domains in poly(ethylene oxide) (PEO) were probed by differential scanning calorimetry (DSC), optical microscopy (OM), and Fourier transform infrared spectroscopy (FTIR). Addition of lithium perchlorate (LiClO₄, up to 10% of the total mass) led to enhanced T_g's, but did not disturb the miscibility state in the amorphous phase of PEO/PVPh blends, where the salt in the form of lithium cation and ClO anion was well dispersed in the matrix. Competitive interactions between PEO, PVPh, and Li⁺ and ClO ions were evidenced by the elevation of glass transition temperatures and shifting of IR peaks observed for LiClO₄‐doped PEO/PVPh blend system. However, the doping distinctly influenced the crystalline domains of LiClO₄‐doped PEO or LiClO₄‐doped PEO/PVPh blend system. LiClO₄ doping in PEO exerted significant retardation on PEO crystal growth. The growth rates for LiClO₄‐doped PEO were order‐of‐magnitude slower than those for the salt‐free neat PEO. Dramatic changes in spherulitic patterns were also seen, in that feather‐like dendritic spherulites are resulted, indicating strong interactions. Introduction of both miscible amorphous PVPh polymer and LiClO₄ salt in PEO can potentially be a new approach of designing PEO as matrix materials for electrolytes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3357–3368, 2006     

Fluoropolyethers end‐capped by polar functional groups. IV. A novel approach to the evaluation of reactivities of hydroxy‐terminated ethoxylated fluoropolyethers in the tin(IV)‐catalyzed reactions with isophorone diisocyanate

The effect of catalyst dibutyltin dilaurate (DBTDL) on the kinetics of urethane formation reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers Fomblin® Z‐DOL TXs (FPEs) of various molecular weights and poly(oxyethylene) glycol PEG‐400 with isophorone diisocyanate (IPDI) in hexafluoroxylene (HFX) and tetrahydrofuran (THF) at 40 °C and NCO:OH = 2:1 have been studied in a broad range of catalyst (0.10–9.00) ×10^?4 M and total reagents (10.0–60.1 wt %) concentrations. The rate of tin‐catalyzed second‐order reactions (with respect to diol and diisocyanate) was found to be proportional to the square root of catalyst concentration [DBTDL]^0.5 both in low polar (HFX) and polar (THF) solvents. Effect of catalyst saturation was revealed for all the reaction systems at higher DBTDL concentrations as well as the appearance of the limiting catalyst concentrations C_lim below which the rates of reaction were close to zero. Based on these findings new effective rate coefficients have been derived k = k_cat/(C ? C) that are independent of the total reagent concentration in the range of 10.0–60.1 wt % ([OH] = 0.10–0.91 equiv/L). This new approach highlights that the rate of the tin‐catalyzed urethane formation reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers Z‐DOL TXs with IPDI in HFX at 40 °C and NCO:OH = 2:1 increases significantly with increasing MW of FPE from 776 up to 3405. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5354–5371, 2004     

Effects of carbon nanotubes on dynamic mechanical property,thermal property,and crystal structure of poly(L‐lactic acid)

Effects of carbon nanotubes (CNT) on the dynamic mechanical property, thermal property, and crystal structure of poly(L ‐lactic acid) (PLLA) were investigated. Dynamic mechanical analysis (DMA) found that CNT via grafting modification with PLLA (CNT‐g‐PLLA) could result in effective reinforcing effects. Tan δ of DMA found that CNT‐g‐PLLA was compatible with the PLLA matrix, giving a single T_g of the composite with a higher CNT‐g‐PLLA loading giving a higher T_g of the composite. Wide angle X‐ray diffraction (WAXD) data demonstrated that CNT could assist the disorder‐to‐order (α′‐to‐α) transition in PLLA crystals but did not lead to a more compact chain packing of the crystal lattice in PLLA composites than in pure PLLA. The equilibrium melting temperature (T) obtained from Hoffman‐Weeks plots were found to increase with increasing CNT‐g‐PLLA content. Small angle X‐ray scattering data revealed that thicknesses of crystal layer and amorphous layer of PLLA both decreased with increasing CNT contents. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 145–152, 2010     

Thermodynamic and kinetic thermal analyses on dual crystal forms in polymorphic poly(heptamethylene terephthalate)

Thermal analyses were performed for determining the equilibrium melting temperatures T of the respective α‐ and β‐crystal in melt‐crystallized polymorphic poly(heptamethylene terephthalate) (PHepT) using both linear and nonlinear Hoffman‐Weeks (H‐W) methods for comparison of validity. These two crystals in PHepT do not differ much in their melting temperatures. The equilibrium melting temperatures of the α‐ and β‐crystal as determined by the linear H‐W method are 98 °C and 100.1 °C, respectively; but the nonlinear H‐W method yielded higher values for both crystals. The equilibrium melting temperatures of the α‐ and β‐crystal according to the nonlinear H‐W method are 121 °C and 122.5 °C, respectively. Both methods consistently indicate that T of the β‐crystal is only slightly higher than that of the α‐crystal. Such small difference in T between the α‐ and the β‐crystal causes difficulties in judging the relative thermodynamic stability of these two crystals. Thus, kinetics of these two crystals was compared using the Avrami and Ozawa theory. The crystallization produced by quenching from T_max = 110 °C and 150 °C shows a heterogeneous and homogeneous nucleation mechanism, respectively. The lower T_max = 110 °C leads to heterogeneous nucleation and only α‐crystal in PHepT, whose crystallization rates at same T_c are much higher than crystallization rates by quenching from T_max = 150 °C leading to either α‐ or β‐crystal with homogeneous nucleation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1839–1851, 2009     

Darstellung und Kristallstruktur von trans-(Ph4As)2[OsCl2(NCS)(SCN)], Schwingungsspektren und Normalkoordinatenanalyse

Preparation and Crystal Structure of trans-(Ph₄As)₂[OsCl₂(NCS) (SCN) ], Vibrational Spectra and Normal Coordinate Analysis By treatment of trans-[OsCl₂I₄]^2? with (SCN)₂ in dichloromethane a mixture of different linkage isomers is formed, from which trans-[OsCl₂(NCS)(SCN)]^2? has been isolated by ion exchange chromatography on diethylaminoethyl cellulose. The X-Ray structure determination on a single crystal of trans-(Ph₄As)₂[OsCl₂(NCS)(SCN)] (triclinic, space group P 1 , a = 12.505(5), b = 12.056(5), c = 19.833(5) Å, α = 108.047(5)°, β = 91.964(5)°, γ = 117.048(5)°, Z = 2) reveals that two cis-positioned Thiocyanate(N) groups are coordinated with Os? N? C angles of 172.1° and 173.0° and two cis-positioned Thiocyanate(S) groups are coordinated with Os? S? C angles of 106.9° and 108.7°. Using the molecular parameters of the X-Ray determination the low temperature (10 K) IR and Raman spectra of the (n-Bu₄N) salt of the linkage isomer are assigned by a normal coordinate analysis based on a modified valence force field. The valence force constants are f_d(OsN) = 1.63 and f_d(OsS) = 1.30 mdyn/Å. Taking into account the trans influence a good agreement between observed and calculated frequencies is achieved.     

Spin probe mobility in relation to free volume and relaxation dynamics of glass‐formers: A series of spin probes in poly(isobutylene)

We present the dynamics of a series of three paramagnetic molecules of different volume, mass, and shape in amorphous glass‐forming polymer poly(isobutylene) (PIB) as investigated by means of electron spin resonance (ESR) technique. The reorientation behavior of spin probes is related to the ortho‐positronium (o‐Ps) annihilation in PIB from positron annihilation lifetime spectroscopy (PALS) and the extracted free volume information. It is also related to the dynamic data of PIB from broadband dielectric spectroscopy (BDS), neutron scattering (NS), and nuclear magnetic resonance (NMR) spectroscopy from literature. In the case of the smallest spin probe, 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO), a discontinuous course of the spectral parameter 2A_zz′ versus T dependence was observed and the subsequent phenomenological model‐free analyses of the spectral parameter, 2A_zz′ versus T, as well as of the correlation time, τ_c, versus 1/T plots provided the characteristic ESR temperatures ( , T_50G, ) and (T, T, T). These characteristic ESR temperatures were found to be consistent with the characteristic PALS temperatures: T, T = T from temperature dependences of the mean o‐Ps lifetime, τ₃, or the width of o‐Ps lifetime distribution, σ₃, respectively. In addition, the relationships between the spin probe size, V, and the free volume hole size distributions g_n(V_h) at the characteristic ESR temperatures indicate the significant influence of the free volume fluctuation at the crossover from slow to rapid regime as well as within the rapid motional regime. On the other hand, the two larger spin probes exhibit a rather continuous 2A_zz′–T plots with the respective T_50G's lying in the vicinity of T independently of their volume, mass and shape, suggesting the common origin of underlying process controlling this T_50G transition. Finally, these mutual PALS and ESR findings were compared with the known dynamic behavior of PIB which suggest that the dynamics of the TEMPO and the larger spin probes are related to free volume fluctuation associated with primary α ‐ and secondary β processes, respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1058–1068, 2009     

Synthese und Kristallstruktur von [N(Hex)4][Cu2(CN)3]

Synthesis and Crystal Structure of [N(Hex)₄] [Cu₂(CN)₃] [N(Hex)₄][Cu₂(CN)₃] has been prepared by solvothermal reaction of CuCN with Tetra‐n‐hexylammoniumiodide in acetone. The crystal structure is built up by condensed (CuCN)₆ and (CuCN)₇ rings, forming a zeolith type cyanocuprate(I) framework [Cu₂(CN)₃^—]. Space group R3; α = 44.482(6), c = 21.283(4) Å, V = 36471(9) ų; Z = 9.     

Crystallization kinetics of poly(trimethylene terephthalate)

The isothermal crystallization kinetics of poly(trimethylene terephthalate) (PTT) have been investigated using differential scanning calorimetry (DSC) and polarized light microscopy (PLM). Enthalpy data of exotherm from isothermal crystallization were analyzed using the Avrami theory. The average value of the Avrami exponent, n, is about 2.8. From the melt, PTT crystallizes according to a spherulite morphology. The spherulite growth rate and the overall crystallization rate depend on crystallization temperature. The increase in the spherulitic radius was examined by polarized light microscopy. Using values of transport parameters common to many polymers (U* = 1500 cal/mol, T_∞= T_g − 30 °C) together with experimentally determined values of T (248 °C) and T_g (44 °C), the nucleation parameter, k_g, for PTT was determined. On the basis of secondary nucleation analyses, a transition between regimes III and II was found in the vicinity of 194 °C (ΔT ≅ 54 K). The ratio of k_g of these two regimes is 2.1, which is very close to 2.0 as predicted by the Lauritzen–Hoffman theory. The lateral surface‐free energy, σ = 10.89 erg/cm² and the fold surface‐free energy, σ_e = 56.64 erg/cm² were determined. The latter leads to a work of chain‐folding, q = 4.80 kcal/mol folds, which is comparable to PET and PBT previously reported. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 934–941, 2000     

Rheological properties of poly(lactides). Effect of molecular weight and temperature on the viscoelasticity of poly(l‐lactic acid)

The dynamic viscoelastic behavior of Poly(l‐lactic acid) (PLLA), with molecular weights ranging from 2,000 to 360,000, have been studied over a broad range of reduced frequencies (approximately 1 × 10⁻³ s⁻¹ to 1 × 10³ s⁻¹), using time–temperature superposition principle. Melts are shown to have a critical molecular weight, M_c, of approximately 16,000 g/mol, and an entanglement density of 0.16 mmol/cm³ (at 25°C). PLLA polymers are noted to require substantially larger molecular weights in order to display similar melt viscoelastic behavior, at a given temperature, as that for conventional non‐biodegradable polymers such as polystyrene. The reason for this deviation is suspected to be due to steric hindrance, resulting from excessive coil expansion or other tertiary chain interactions. PLLA melts show a dependence of η₀ on chain length to the 4.0 power (M), whilst J is independent of M_W in the terminal region. Low molecular weight PLLA (∼ 40,000) shows Newtonian‐like behavior at shear rates typical of those achieved during film extrusion. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1803–1814, 1999     

Synthesis and Structure of a One‐Dimensional Aluminum Phosphate, [NH3(CH2)2NH2(CH2)3NH3]3+ [Al(PO4)2]3—

A one‐dimensional aluminum phosphate, [NH₃(CH₂)₂NH₂(CH₂)₃NH₃]³⁺ [Al(PO₄)₂]^3—, has been synthesized hydrothermally in the presence of N‐(2‐Aminoethyl‐)1, 3‐diaminopropane (AEDAP) and its structure determined by single crystal X‐ray diffraction. Crystal data: space group = Pbca (no. 61), a = 16.850(2), b = 8.832(1), c = 17.688(4)Å, V = 2632.4(2)ų, Z = 8, R₁ = 0.0389 [5663 observed reflections with I > 2σ(I)]. The structure consists of anionic [Al(PO₄)₂]^3— chains built up from AlO₄ and PO₄ tetrahedra, in which all the AlO₄ vertices are shared and each PO₄ tetrahedron possesses two terminal P=O linkages. The cations, which balances the negative charge of the chains, are located in between the chains and interact with the oxygen atoms through strong N—H···O hydrogen bonds. Additional characterization of the compound by powder XRD and MAS‐NMR has also been performed and described.     

Arrhenius parameters for the gas‐phase reactions of O3 with two butenes and two methyl‐substituted butenes over the temperature range of 295–351 K

Gas‐phase reactions of ozone with two butenes (1‐butene and isobutene) and two methyl‐substituted butenes (2‐methyl‐1‐butene and 3‐methyl‐1‐butene) have been studied in an indoor chamber at 295–351 K. The O₃ concentrations were monitored by Model 49C‐Ozone analyzer. The butene concentrations were measured by gas chromatography–flame ionization detector. The Arrhenius expressions of k=3.50×10^?15e^{(?1756±84)/T} cm³ molecule^?1 s^?1, k=3.39×10^?15e^{(?1697±52)/T} cm³ molecule^?1 s^?1, k=6.18×10^?15e^{?(1822±80)/T} cm³ molecule^?1 s^?1, and k=7.24×10^?14e^{?(2741±139)/T} cm³ molecule^?1 s^?1 were obtained for the ozonolysis reactions of 1‐butene, isobutene, 2‐methyl‐1‐butene, and 3‐methyl‐1‐butene, respectively. Both the reaction rate constant and activation energy obtained in this work are in good agreement with those reported by using different techniques in the literature. © 2011 Wiley Peiodicals, Inc. Int J Chem Kinet 43: 238–246, 2011     

Thermal,morphology, and NMR characterizations on phase behavior and miscibility in blends of isotactic polystyrene with poly(cyclohexyl methacrylate)

The miscibility and phase behavior in a binary blend of isotactic polystyrene (iPS) and poly(cyclohexyl methacrylate) (PCHMA) were investigated by differential scanning calorimetry, optical microscopy (OM), and solid‐state ¹³C cross‐polarity/magic‐angle spinning NMR. The iPS/PCHMA blend was miscible when all compositions showed a single composition‐dependent glass‐transition temperature (T_g) and when the blend went through a thermodynamic phase transition upon heating to above the lower critical solution temperature as determined by OM measurements. The ¹H NMR spin‐relaxation times in the laboratory frame (T) and in the rotating frame (T) for iPS/PCHMA blends with various compositions and neat components were directly measured through solid‐state¹³C NMR. The results of T indicated that the blends are homogeneous, at least on a scale of 75–85 nm, confirming the miscibility of the system. The single decay and composition‐dependent T values for each blend further demonstrated the blends are homogeneous on a scale of 2.5–3.5 nm. The results suggested that iPS and PCHMA are intimately mixed at the molecular level within the blends at all compositions. The tacticity of polystyrene does not seem to adversely influence the miscibility in blends of iPS/PCHMA. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 772–784, 2003