Efficient 1.8 μm KTiOPO4 optical parametric oscillator pumped within an Nd:YAG/SrWO4 Raman laser

A 1.8?μm optical parametric oscillator (OPO) based on a noncritically phase-matched KTiOPO4 crystal is demonstrated. OPO and stimulated Raman scattering techniques are successfully combined in an acousto-optically Q-switched Nd:YAG/SrWO4 Raman laser. The device efficiently realizes three steps of conversion: from a laser diode wavelength of 808?nm to the fundamental wavelength of 1064?nm; next, to the Stokes wavelength of 1180?nm; and finally to the OPO signal wavelength of 1810?nm. With an incident diode power of 7.2?W and a pulse repetition rate of 15?kHz, an average signal power of 485?mW is obtained with a diode-to-signal conversion efficiency of 6.75%. The beam quality factors (M2) of the signal wave in both horizontal and vertical directions are measured to be 1.7±0.2. The numerical output power results of the system, the thermal lensing, and the stability parameter of the cavity are also discussed.     

Development of injection-seeded, pulsed optical parametric generator/oscillator systems for high-resolution spectroscopy

We report the development and application of pulsed optical parametric generator (OPG) and optical parametric oscillator (OPO) systems that are injection seeded with near-infrared distributed feedback diode lasers. The OPG is injection seeded at the idler wavelength without the use of a resonant cavity. Two counter-rotating, beta-barium-borate (β-BBO) crystals are used in the OPG. These crystals are pumped by the third harmonic, 355-nm output of an injection-seeded Nd:YAG laser. An OPO version of the system has also been developed by placing two flat mirrors around the two β-BBO crystals to form a feedback cavity at the signal wavelength. The OPO cavity length is not actively controlled. The output signal beam from the OPG or OPO is amplified using an optical parametric amplifier (OPA) stage with four β-BBO crystals. The frequency bandwidths of the signal and idler laser radiation from OPG/OPA and OPO/OPA systems have been determined to be slightly greater than 200 MHz. The temporal pulses from each system are smooth and near-Gaussian. High-resolution optical absorption measurements of acetylene (C₂H₂) were performed as another check of the frequency spectrum of the idler beam. The frequency-doubled signal output of the OPO/OPA system was used to perform high-resolution, single-photon, laser-induced fluorescence (LIF) spectroscopic studies of the (0,0) vibrational band of the A ²Σ⁺−X ²Π electronic transition of nitric oxide (NO) at low pressure. Excellent agreement was obtained between the theory and the experiment. The signal output of the OPG/OPA system was also used for sub-Doppler, two-photon LIF spectroscopic studies of the same vibration–rotation manifold of NO.This revised version was published online in August 2005 with a corrected cover date.     

Frequency-stable operation of a diode-pumped continuous-wave RbTiOAsO(4) optical parametric oscillator

Frequency-stable operation of a diode-pumped continuous-wave optical parametric oscillator (OPO) of RbTiOAsO(4) is demonstrated. Piezoelectric and fast electro-optic control of the optical length of the two-mirror OPO cavity (resonant for the pump and the idler waves) compensates for thermal changes in the refractive index of the OPO crystal (induced by absorption of pump light) and acoustic perturbations of the cavity length. Pumped by 405mW of the 810-nm output of a GaAlAs masterf-oscillator-tapered-amplifier diode laser system, the OPO generates a power-stable single-frequency signal wave at 1.24microm with an output of 84mW and a spectral bandwidth of less than 10MHz.     

Spectroscopic diagnostics of chemical processes: applications of tunable optical parametric oscillators

Optical parametric oscillator (OPO) and amplifier (OPA) devices are useful for spectroscopic sensing of chemical processes in laboratory, industrial, and environmental settings. This is particularly true of nanosecond-pulsed, continuously tunable OPO/OPA systems, for which we survey a variety of instrumental strategies, together with actual spectroscopic measurements. The relative merits of OPO wavelength control by intracavity gratings and by injection seeding are considered. A major innovation comprises an OPO with a ring cavity based on periodically poled lithium niobate (PPLN) and injection-seeded by a single-mode tunable diode laser (TDL). Active cavity control by an ‘intensity dip’ method yields an optical bandwidth ≤0.005 cm^-1 (150 MHz), which compares favourably with the performance of advanced grating-tuned OPO/OPA systems. A novel adaptation of this TDL-seeded PPLN OPO employs a compact, inexpensive multimode pump laser, with which it is still possible to obtain continuously tunable single-mode signal output. Cavity ringdown (CRD) spectroscopy also figures prominently, with infrared (IR) CRD spectra from both grating-scanned and TDL-seeded OPOs reported. Finally, a tunable ultraviolet (UV) source, combining a TDL-seeded passive-cavity OPO and a sum-frequency generation stage, is developed for measurements of time-resolved IR-UV double resonance spectra of acetylene and UV laser-induced fluorescence spectra of nitric oxide. Received: 28 March 2000 / Published online: 13 September 2000     

2.5-GHz repetition-rate singly resonant optical parametric oscillator synchronously pumped by a mode-locked diode oscillator amplifier system

We report on an optical parametric oscillator (OPO) that is synchronously pumped directly by a diode laser. This laser is an actively mode-locked master-oscillator power-amplifier system that produces 20-ps pulses at 927 nm with a repetition rate of 2.5 GHz and an average power of 0.9 W. The OPO, which is a singly resonant device based on periodically poled lithium niobate, generates 7.8-ps pulses. The OPO threshold is 300 mW of average pump power, and the maximum average idler output power is 78 mW at a wavelength of 2100 nm. By changing the crystal temperature we can wavelength tune the output in the ranges 1530-1737 nm (signal) and 1986-2348 nm (idler). Rapid wavelength tuning of the OPO over 46 nm (signal) and 74 nm (idler) is achieved through tuning the cavity length over 28 microm by use of a piezoelectric transducer.     

Efficient sub-nanosecond intracavity optical parametric oscillator pumped with a passively Q-switched Nd:GdVO<Subscript>4</Subscript> laser

An efficient diode-pumped passively Q-switched Nd:GdVO₄/Cr⁴⁺:YAG laser was employed to generate a high-repetition-rate, high-peak-power eye-safe laser beam with an intracavity optical parametric oscillator (OPO) based on a KTP crystal. The conversion efficiency for the average power is 8.3% from pump diode input to OPO signal output and the slope efficiency is up to 10%. At an incident pump power of 14.5 W, the compact intracavity OPO cavity, operating at 46 kHz, produces average powers at 1571 nm up to 1.2 W with a pulse width as short as 700 ps. PACS 42.60.Gd; 42.65.Yj; 42.55.X     

Low-threshold singly-resonant continuous-wave optical parametric oscillator based on MgO-doped PPLN

We present a 532 nm-pumped singly-resonant cw optical parametric oscillator based on MgO-doped PPLN with a minimum threshold pump power of 0.3 W. The OPO with a two-mirror standing-wave cavity is optimized by using a tunable diode laser on the path of the resonant signal beam. The maximum output power is 200 mW at an idler wavelength near 1330 nm at a pump power of 2 W. We report the degradation of the output power and beam characteristics at high pump power indicating a strong thermal lensing in the crystal. The continuous tuning range of the OPO is measured to be 800 MHz which is close to 90% of the free spectral range of the OPO cavity.     

Continuous wave optical parametric oscillator for quartz-enhanced photoacoustic trace gas sensing

A continuous wave optical parametric oscillator, generating up to 300 mW idler output in the 3–4 μm wavelength region, and pumped by a fiber-amplified DBR diode laser is used for trace gas detection by means of quartz-enhanced photoacoustic spectroscopy (QEPAS). Mode-hop-free tuning of the OPO output over 5.2 cm^-1 and continuous spectral coverage exceeding 16.5 cm^-1 were achieved via electronic pump source tuning alone. Online monitoring of the idler wavelength, with feedback to the DBR diode laser, provided an automated closed-loop control allowing arbitrary idler wavelength selection within the pump tuning range and locking of the idler wavelength with a stability of 1.7×10^-3 cm^-1 over at least 30 min. Using this approach, we locked the idler wavelength at an ethane absorption peak and obtained QEPAS data to verify the linear response of the QEPAS signal at different ethane concentrations (100 ppbv-20 ppmv) and different power levels. The detection limit for ethane was determined to be 13 ppbv (20 s averaging), corresponding to a normalized noise equivalent absorption coefficient of 4.4×10^-7 cm^-1  W/Hz^1/2. PACS 42.55.Wd; 42.65.Yj; 42.62.Fi     

Compact eye-safe intracavity optical parametric oscillator with efficient pulse shortening

We report a compact eye-safe intracavity optical parametric oscillator (IOPO), driven by a diode end-pumped passively Q-switched Nd:YVO₄/Cr: YAG laser. At the incident diode pump power of 6.2 W and signal pulse repetition rate of 13 kHz, we obtain a minimum signal pulse duration as short as 1.3 ns, holding a pulse compressing factor of 17 with respect to that of the pump, and exhibiting an efficient pulse shortening mechanism. At the same time, the maximum average power of 110 mW and pulse energy of 8.5 μJ for the signal wave are also achieved. In addition, cavity dumping characteristics and the correlation dynamics between the laser and the OPO are qualitatively analyzed.     

Rapidly tunable continuous-wave optical parametric oscillator pumped by a fiber laser

We report on rapid, all-electronically controlled wavelength tuning of a continuous-wave (cw) optical parametric oscillator (OPO) pumped by an ytterbium fiber laser. The OPO is singly resonant for the signal wave and consists of a 40-mm-long periodically poled lithium niobate crystal in a four-mirror ring cavity. By tuning of the fiber-laser wavelength over 33 nm through an intracavity acousto-optic tunable filter, the OPO idler wavelength is tuned from 3160 to 3500 nm in 330 micros, corresponding to an idler frequency-tuning speed of 28 THz/ms. At a fiber-laser power of 6.6 W at 1074 nm, the singly resonant OPO generates 1.13-W cw idler radiation at 3200 nm.     

8.30 μm singly resonant ZnGeP2 optical parametric oscillators pumped by a Tm,Ho:GdVO4 laser

A single resonator 8.30 μm ZnGeP₂ (ZGP) optical parametric oscillators (OPO) was reported in the paper. The OPO was pumped by a 10.2-W Tm,Ho:GdVO₄ laser at 8 kHz in a Q-switch mode, a 170-mW idler was obtained at 8.30 μm, and the output power of the idler and signal wave was 1.0 W, corresponding to an optical-optical conversion efficiency of 10.3% and a slope efficiency of 20.9%. Tm,Ho:GdVO₄ laser was pumped by a 30-W fiber-coupled laser diode (LD) at the center wavelength of 801 nm. The output wavelength of Tm,Ho:GdVO₄ laser was at 2.05 μm, and the energy per pulse of 1.28 mJ in 18 ns was achieved at 8 kHz with the peak power of 71.1 kW.     

Fiber-laser-pumped continuous-wave singly resonant optical parametric oscillator

We report on what is to our knowledge the first continuous-wave (cw) optical parametric oscillator (OPO) that is pumped by a tunable fiber laser. The OPO is singly resonant for the signal wave and consists of a 40-mm-long periodically poled LiNbO(3) crystal in a four-mirror ring cavity. At a pump power of 8.3 W provided by the wavelength-tunable Yb-doped fiber laser, the singly resonant OPO generates 1.9 W of 3200-nm cw idler radiation. The singly resonant OPO was tuned from 1515 to 1633 nm (signal) and from 3057 to 3574 nm (idler) by means of the crystal temperature and poling period. We obtained a wide idler tuning range, from 2980 to 3700 mn, by tuning the wavelength of the fiber laser from 1032 to 1095 nm.     

High-power,high-quality ZGP OPO pumped by a Tm,Ho:GdVO<Subscript>4</Subscript> laser

We report a ZGP OPO system capable of producing >6 W at a signal wavelength of 3.80 μm and an idler wavelength of 4.45 μm. The pumping source is the Tm,Ho:GdVO₄ laser operated at 2.049 μm with an M ² of 1.07. The ZGP OPO generated a total combined output power of 6.1 W at signal wavelength and idler wavelength under pumping power of 18.3 W, and an M ² of 1.7 for OPO output was obtained.     

Grating-Stabilized External Cavity Diode Lasers for Raman Spectroscopy—A Review

Abstract: Conventional Raman techniques require a continuous-wave laser with stabilized wavelength, narrow line width, and sufficient output power. Due to their miniature size and low cost, diode lasers are good choice as light sources for Raman spectroscopy, especially when compact and portable instruments are needed. However, a solitary multimode diode laser has certain drawbacks that limit its use for Raman application. To circumvent these drawbacks, an external cavity can be coupled to the active gain medium of the diode to enhance the laser performance. A grating-based external cavity allows the laser to operate in a single longitudinal mode with greatly reduced line width and stabilized wavelength. This article examines the fundamentals of semiconductor lasers to show the necessity of operating diode lasers in an external cavity for Raman applications. Two feedback grating-based external cavity diode laser (ECDL) designs, viz. Littrow and Littman-Metcalf configurations, are explained. Historic and recent progress in the development of ECDL devices is reported. An updated summary of ECDL-equipped Raman systems applied to fields such as in vivo biomedical studies and in situ process/quality control is provided. Topics on mode-hop-free continuous scanning, wavelength stabilization, and dealing with ambient conditions are discussed.     

Highly stable and efficient KTP-based intracavity optical parametric oscillator with a diode-pumped passively Q-switched laser

We present in this paper a highly stable and efficient KTP-based intracavity optical parametric oscillator with a diode-end-pumped Nd:YVO₄/Cr:YAG passively Q-switched laser. At the incident diode pump power of 4 W, the signal (1.57 μm) and idler (3.29 μm) average output powers up to 580 and 100 mW, respectively, have been achieved. The corresponding conversion efficiency from the input diode pump power to the output signal power is 14.5%, while that to the total OPO output (signal+idler) reaches 17%. To the best of our knowledge, these are the highest conversion efficiencies reported to date. After more than four hours of investigation, the OPO power stability better than 2% has been obtained. In addition, efficient cavity dumping of the IOPO has inevitably led to the short pulse duration (1.6 ns) and high peak power output (8.3 kW) at the signal wave. Additionally, the amplitude and repetition rate fluctuations of the signal pulses are well within 5%. PACS 42.55.Xi; 42.60.Gd; 42.60.Lh; 42.65.Yj     

An efficient intracavity-pumped KTP optical parametric oscillator at 1572 nm

We demonstrate an efficient and eye-safe wavelength intracavity optical parametric oscillator (OPO),based on a KTP crystal inside a Q-switched Nd:YVO4 laser end pumped by a fiber-coupled diode laser. Inthe acousto-optic Q-switched operation with the pulse repetition rate of 10 kHz, a 1572-nm eye-safe laser with the average power of 237 mW at the incident pump power of 5.64 W is obtained. Under the pulse repetition rate of 5 kHz, the signal light with pulse width of 2 ns and peak power of 18.5 kW is achieved.The conversion efficiency of the average power is 4.2% from pump diode to OPO signal output and thesignal pulse duration is about 13 times shorter than that of the depleted pump light.     

High-power mid-infrared tunable optical parametric oscillator based on 3-mm-thick PPMgCLN

The experimental results of a high-power tunable mid-IR laser are presented. The optical parametric oscillator (OPO) with a 3-mm-thick PPMgCLN crystal was pumped by a 1.064 μm pulse laser. When the pump power of the 1.064 μm laser was 151 W at 10 kHz, and the operating temperature of the PPMgCLN with 5% MgO doping was 100°C, average output power of 23.7 W at 3.91 μm was obtained with a slope efficiency of 18.2% for the idler resonant OPO. The variation of the 3.91 μm output power was about ±4% in 10 min continuous operation. The beam quality factor M ² was less than 2.6. The average output power of 27.4 W at 3.91 μm was also obtained with 151 W pump power and the slope efficiency of 20.9% for the signal resonant OPO by changing the coating parameters of the OPO cavity mirrors. The mid-IR wavelength tunability of 3.7–4.0 μm can be achieved by adjusting the temperature of a 29 μm period PPMgCLN crystal from 200 to 30°C.     

Stable, continuously tunable operation of a diode-pumped doubly resonant optical parametric oscillator

We demonstrate, for what is the first time to our knowledge, long-term stable, continuously tunable operation of a doubly resonant optical parametric oscillator (OPO) pumped by a single-stripe diode laser without the use of an external semiconductor amplifier. The OPO is based on periodically poled lithium niobate and is pumped by a 150-mW distributed Bragg grating diode laser. 18-mW total output power is generated at 1.3- and 2.3-mum wavelengths. A cavity-length servo system allows continuous signal tuning of 17 GHz and idler tuning of 10 GHz, limited only by the range of a piezoelectric cavity mirror mount. OPO tuning is demonstrated from 1.1 to 1.4 mum and from 2.2 to 3.7 mum.     

Dye laser pumped, continuous-wave KTP optical parametric oscillators

4 (KTP) optical parametric oscillators (OPOs) with pump and idler resonant cavities. With a linear two-mirror cavity the pump power at threshold was 70 mW. The single-frequency signal and idler output wavelengths were tuned in the range of 1025 to 1040 nm and 1250 to 1380 nm by tuning the dye laser in the range of 565 to 588 nm. With a dual three-mirror cavity the threshold was 135 mW. Pumped by 500 mW of 578 nm radiation the 1040 nm single-frequency signal wave output power was 84 mW. Power and frequency stable operation with a spectral bandwidth of less than 9 MHz was obtained by piezo-electrically locking the length of the pump resonant cavity to the dye laser wavelength. Similar performance was achieved by placing the idler resonant OPO inside the resonator of the dye laser. With this system power stable and single-frequency operation was achieved with a spectral bandwidth of less than 11 MHz for the idler wave. Received: 3 February 1998/Revised version: 9 March 1998     

Rapid and sensitive trace gas detection with continuous wave Optical Parametric Oscillator-based Wavelength Modulation Spectroscopy

A fiber-amplified Distributed Bragg Reflector diode laser is used to pump a continuous wave, singly resonant Optical Parametric Oscillator (OPO). The output radiation covers the 3–4 μm with ability of rapid (100 THz/s) and broad mode-hop-free tuning (5 cm⁻¹). Wavelength Modulation Spectroscopy is combined with the OPO to take optimal advantage of the spectral scan speed. The sensitivity of the system was determined as 0.8 ppbv (parts-per-billion by volume) for ethane (C₂H₆) for the absorption peak at 2996.9 cm⁻¹ recorded in 1.3 seconds, corresponding to a noise equivalent absorption sensitivity (NEAS) of 1.2×10⁻⁹ cm⁻¹/Hz^1/2. A comparison between results using the 1^st, 2^nd and 4^th harmonic derivative signal from wavelength modulation was performed. The broad continuous tunability was demonstrated by covering 35 cm⁻¹ while recording absorption features of ethane, methane and water.