TiCl_4／SiO_2－MgCl_2载体催化剂下的乙烯／己烯－1共聚反应

ＴｉＣｌ_４／ＳｉＯ_２－ＭｇＣｌ_２载体催化剂下的乙烯／己烯－１共聚反应陈辉，张学全，黄葆同王展望，杨永然（中国科学院长春应用化学研究所长春１３００２２）（辽阳化纤公司化工三厂辽阳）关键词乙烯，己烯，共聚，Ｚｉｅｇｌｅｒ－Ｎａｔｔａ催化剂乙烯／α－烯?..     

微波辐射快速合成2-(2′-羟苯基)-5(6)取代苯并咪唑衍生物

苯并咪唑衍生物具有一定的抗病毒能力[1 ] ,一些苯并咪唑衍生物已用作农用抗植物病毒剂[2 ] 。一锅煮合成反应时间较长 ,产率中等[3,4] 。本文用取代邻苯二胺和水杨酸为原料 ,吡啶为溶剂 ,ＰＯＣｌ3为催化剂 ,微波辐射法合成了标题化合物。合成路线如下 :1　实验部分1 1　仪器ＷＣ 1型熔点测定仪 (温度计未校正 ) ;日本岛津ＩＲ 435红外光谱仪 (ＫＢｒ压片 ) ;ＴＥＯＬ ＦＸ90Ｑ核磁共振仪 ,ＤＭＳＯ ｄ6 为溶剂 ;日本柳公Ｃ·Ｈ·Ｎ元素分析仪ＭＴ 3;苏州三星电子有限公司产新天地Ｍ9Ｋ88型微波炉 ,输出功率 85 0Ｗ ,2 4 5 0Ｈｚ。1 2　…     

MgCl_2负载(dbm)_2Ti(OPh)_2催化乙烯聚合

烯烃聚合的新型非茂催化剂由于合成相对简便并具有一些新特点,近年来开始受到人们的关注[1,2].ＩＶＢ族金属的β二酮络合物与烷基铝或烷氧基铝形成的催化体系对烯烃聚合也显现出一定的聚合活性.在一定压力下,β二酮锆/ＭＡＯ均相催化乙烯聚合时具有较高聚合活性[3].β二酮钛催化剂对于丙烯无规聚合和苯乙烯间规聚合均有较好结果[4～6].本文将报道用ＭｇＣｌ2负载的二苯氧基二(二苯甲酰甲烷)钛络合物((ｄｂｍ)2Ｔｉ(ＯＰｈ)2),以甲基铝氧烷(ＭＡＯ)为助催化剂,常压催化乙烯聚合的结果.1　原料ＭｇＣｌ2为抚顺301厂产品.ＭＡＯ(1.4ｍｏｌ/Ｌ甲…     

钛系Ziegler－Natta催化剂下的丙烯／α－烯烃的共聚合

研究了ＴｉＣｌ＿４／ＭｇＣｌ＿２－三乙基铝（ＴＥＡ）高效载体催化体系下的丙烯／癸烯－１共聚及δ－ＴｉＣｌ＿３－－氯二乙基铝（ＤＥＡＣ）催化体系下的丙烯／辛烯－１共聚合的基本反应规律，考察了铝钛比、温度、共聚单体浓度等对共聚合的影响；对比了两种催化体系的不同，利用非均相Ｚｉｅｇｌｅｒ－Ｎａｔｔａ催化体系下共聚合的非稳态扩散动力学的观点，解释了观察到的共聚合催化效率增加，共聚物粒子增大等实验现象．     

MgCl_2晶型对丙烯聚合MgCl_2载体催化剂活性的影响

ＭｇＣｌ_２晶型对丙烯聚合ＭｇＣｌ_２载体催化剂活性的影响张明辉，肖世镜中国科学院化学研究所，北京，１００８０）关键词丙烯聚合、ＭｇＣｌ２、载体催化剂近年来，有关ＭｇＣＩ。载体催化剂的研究报道和综述文章不少，但涉及载体晶型对催化剂结构性能的影响却少见．...     

FTIR研究聚丙烯负载型催化剂的制备过程

采用红外光谱跟踪分析用于丙烯聚合的ＭｇＣｌ２负载型催化剂的制备过程,阐明了制备过程中的主要化学变化．认为载体ＭｇＣｌ２含水对催化剂负载过程及钛含量有极大的影响;ＭｇＣｌ２的溶解是一经过中间过渡态的醇化过程;邻苯二甲酸酐不仅会与部分醇反应生成酯,而且还与水反应生成酸,起了除水的作用;其中酯在ＴｉＣｌ４负载中作为内酯,酸容易与－Ｍｇ—（ＯＲ）作用生成Ｍｇ（ＯＨ）２或Ｍｇ（ＯＨ）Ｃｌ;在负载过程中,ＴｉＣｌ４倾向于在ＭｇＣｌ２表面的结构缺陷处与ＭｇＣｌ２发生“结构锚定”．用红外光谱跟踪分析的结论,得到了用不同含水量ＭｇＣｌ２制得的催化剂钛含量和催化活性及ＸＰＳ分析的支持     

用高效SiO2载体催化剂进行乙烯气相聚合

使用球形ＳｉＯ２负载ＭｇＣｌ２－ＴｉＣｌ４高活性催化剂进行乙烯气相聚合，考察了催化剂制备条件和添加剂对催化剂的组成、催化活性以及聚合表观动力学的影响．结果表明，ＳｉＯ２热处理温度和所用的醇对Ｍｇ和Ｔｉ的负载量及乙烯聚合活性有明显的影响．催化剂制备中添加Ｌｅｗｉｓ酸ＳｉＣｌ４或ＡｌＥｔ２Ｃｌ能大幅度提高催化剂的活性，其中以ＳｉＣｌ４的效果最为明显．随着ＳｉＣｌ４用量的增加，乙烯气相聚合的活性显著提高，聚合速度随时间变化由渐升平稳型转变为衰减型     

不同金属离子对CO／Al_2O_3中Co的分布和CoMoK／Al_2O_3催化

在γ－Ａｌ２Ｏ３中加入Ｚｎ２＋，Ｍｇ２＋，Ｃｕ２＋或Ｃｒ３＋后用漫反射光谱法研究了它们对随后加人的Ｃｏ分布的影响，同时还研究了这些离子对水煤气变换反应催化剂ＣｏＭｏＫ／Ａｌ２Ｏ３的催化活性的影响．发现Ｚｎ２＋，Ｍｇ２＋具有阻止Ｃｏ进入载体内层的作用，Ｃｕ２＋，Ｃｒ３＋的作用则相反．四面体配位倾向强的金属离子能阻止Ｃｏ进入载体内层，从而促进水煤气变换反应的催化活性，而八面体配位倾向强的金属离子的效果刚好相反．在６５０℃下，１００ｇＡｌ２Ｏ３含７ｇＭｇＯ时，Ｍｇ能最大限度地阻止Ｃｏ向Ａｌ２Ｏ３内层扩散，从而提高了ＣｏＭｏｋ／Ａｌ２Ｏ３的催化活性．     

相转移催化合成对甲氧基肉桂酸-2-乙基己酯的研究

对甲氧基肉桂酸 2 乙基己酯是一种有效的ＵＶＢ防晒剂[1 ,2 ] ,一般采用Ｃｌａｉｓｅｎ Ｓｃｈｍｉｄｔ缩合反应制得[3] ,但由于催化剂ＫＯＨ处于水相 ,对反应物不能充分起到催化作用导致产率较低[4] 。我们利用乙二醇 (ＰＥＧ)为相转移催化剂合成立体专一的反式对甲氧基肉桂酸 2 乙基己酯 ,产率提高到 72 .5 %。合成路线如下 :1　实验部分1 .1　仪器与试剂ＢＩＯ ＲＡＰＦＴ45 0红外光谱仪 ,用液膜法测试 ;Ｂｒｕｒｅｒ ＡＭ 30 0超导核磁共振仪 (溶剂ＤＣ Ｃｌ3) ;ＭＡＴ/44Ｓ ,ＧＣ ＭＳ型色质联用谱仪 ;试剂均为分析纯 ,上海化学试剂…     

原子吸收法测定中草药中钙、镁、铁、锌、铜和锰

钙、镁、铁、锌、铜、锰都是人体必不可少的元素 ,而中草药中这些元素的测定 ,无论是从中医药学还是营养卫生学的角度而言 ,都显得极其重要和必不可少[1 ,2 ] 。本文采用原子吸收分光光度法连续测定中草药中的钙、镁、铁、锌、铜、锰。1　实验部分1 .1　仪器与试剂Ｚ 80 0 0偏振塞曼原子吸收分光光度计 ,配火焰和石墨炉原子化器 (日本日立公司 )。ＬａＣｌ3溶液( 1 0 0ｇ/Ｌ) ;ＳｒＣｌ2 溶液 ( 5 0ｇ/Ｌ) ;钙、镁、铁、锌、铜、锰混合标准储备液 (Ｃａ、Ｍｇ、Ｆｅ 2ｇ/Ｌ ,Ｍｎ 1ｇ/Ｌ ,Ｚｎ、Ｃｕ 0 5ｇ/Ｌ)。1 .2　样品液的制备准确称…     

Microhydration of the magnesium(II) acetate cation in the gas phase

Electrospray ionization of aqueous solutions of magnesium(II) acetate leads to microhydrated magnesium acetate cations of the type [(CH(3)COO)(2m-1)Mg(m)(H(2)O)(n)](+) with m = 1-4 and n = 0-4, which are characterized by mass spectrometry and, for the cluster with three water molecules, also by infrared multiphoton dissociation spectroscopy. Density functional theory is used to determine the energies of microhydration for the mononuclear species [(CH(3)COO)Mg(H(2)O)(n)](+) with n = 0-6 and the associated changes in molecular structure. While bidentate coordination of the acetato ligand is generally preferred, at higher values of n, a switch to a monodentate coordination becomes energetically competitive.     

Ignition and combustion characteristics of compound of magnesium and boron

Compound of magnesium and boron (MB) is promising to be the ideal substitute of amorphous boron which is usually used as the raw material of boron-based fuel-rich propellants. In this study, the physical characteristics of MB and amorphous boron were studied by the scanning electron microscope, X-ray diffraction and X-ray photoelectron spectroscopy. The thermal reaction characteristics and the ignition and combustion characteristics were investigated through TG/DSC experiments and laser ignition experiments. The experimental results show that the MB particle is much more regular than amorphous boron, which favors for the preparation of boron-based fuel-rich propellants. Magnesium exists in the form of elementary substance, and boron oxide is produced during the preparation of MB which results in the longer ignition delay time of MB. The content of magnesium and the pressure have effects on the MB combustion performance. Although the combustion of magnesium can provide much heat for the combustion of boron, MB with moderate content of magnesium shows the best combustion performance. On the contrast, the ignition delay time of MB is independent on the content of magnesium and the pressure.     

Magnesium optical one-shot sensor based on a coumarin chromoionophore

The characterization of a new irreversible optical absorption-based one-shot sensor for magnesium is described. The magnesium photoactive probe is 7-diethylamino-3-(3,4-ethylendioxybenzoyl)coumarin immobilized in a plasticized polymeric membrane. The magnesium selectivity can be explained in terms of size and charge density of magnesium and charge-separated resonance forms contribution in the excited state of coumarin. The selectivity obtained for magnesium over a variety of naturally occurring species in natural waters meets the requirements for the determination of this ion in water. The one-shot sensor responds between 0.14 and 14mgL(-1) with a sensor-to-sensor reproducibility of 1.3% as [Formula: see text] , at the medium level of the range. The performance of the optical one-shot sensor was tested in the analysis of magnesium in different types of natural waters and soft drinks validating results against a reference procedure.     

镁铝复合氧化物载体的制备与性质研究

以硝酸镁和硝酸铝为原料,用氨水溶液作为pH调节剂,采用共沉淀法制备了镁铝复合氧化物载体,研究了制备过程中镁铝比、pH调节剂种类、水解过程pH值的大小、反应温度、焙烧温度及回流晶化温度对复合氧化物载体理化性质的影响。并以RFCC汽油加氢脱硫为探针反应,考察了以镁铝复合氧化物为载体的催化剂选择性加氢脱硫性能。实验结果表明,在镁铝分子比为10、反应温度为80℃、pH值为9.5条件下制备的镁铝复合氧化物载体具有适宜的比表面积和均匀的孔分布,且晶型较完整,结晶度高。以该复合氧化物为载体制备的催化剂具有良好的RFCC汽油选择性加氢脱硫反应性能。     

The aromatic character of magnesium porphyrins

The aromaticity of magnesium porphyrins have been studied by calculating the nuclear magnetic shieldings in selected points outside the molecules. The strength of the induced ring currents for a given magnetic field have been obtained by using the aromatic-ring-current-shielding (ARCS) method. Nucleus-independent chemical shift (NICS) calculations provide additional information about the current routes in the multiple-ring systems. The total aromatic pathway of magnesium porphyrins must be considered as a superposition of several (4n + 2) pi-electron Huckel pathways. We found that all beta-unsaturated pyrrolic rings have local ring currents the strength of which is 70-90% of the current strength for the pyrrole molecule. The present study also shows that the 18pi-[16]annulene aromatic pathway does not exist in magnesium porphyrins until all four pyrrolic units are saturated in the beta-position.     

Determination of the precise composition of the triple sodium uranyl acetates of magnesium, zinc and nickel, and some observations on the use of the first two compounds for the determination of sodium

Three triple sodium uranyl acetates NaM(UO(2))(3)(CH(3) COO)(9) . nH(2)O in which the bivalent metals M were magnesium, zinc and nickel, have been precipitated and the air-dried compounds analysed for uranium by a highly precise method. Despite contrary claims it has been established that the compounds are precise hexahydrates the maximum deviation of n from 6 in any one analysis being 0.1. The precipitation of sodium as the magnesium or zinc compound gives results which depend on the excess of the reagents, and positive errors can be obtained. It is also concluded that, contrary to the usual belief, the magnesium compound is rather less soluble than the zinc one and is therefore somewhat more sensitive for sodium determination.     

DTA and FT-IR analysis of the rehydration of basic magnesium carbonate

The rehydration characteristics of a commercially produced hydromagnesite and two basic magnesium carbonates synthetically produced from Mg(OH)₂, are presented. The products were dehydrated and dehydroxylated at 325°C before rehydration was attempted. DTA and FT-IR were used to follow the structural changes that occurred during the rehydration processes. The results obtained for the commercially and synthetically produced hydromagnesite products indicated that the original symmetry of the groups was reclaimed during rehydration. This was not observed for the synthetically produced unidentified basic magnesium carbonate product. This investigation provides insight into the rehydration characteristics of a select group of basic magnesium carbonates. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis and Characterization of Carbon-Stabilized Magnesium Nanoparticles

Magnesium nanopowder has attracted many interests in the recent years, which has a very difficult and costly synthesis process because of its high activity. In this work, magnesium nanoparticles stabilized with amorphous carbon (Mg–C nanoparticles) were synthesized by submerged arc discharge technique in kerosene. The arc discharge was generated between two electrodes of magnesium at the arc current of 1 A and arc voltage of 50 V. Mg–C nanoparticles were characterized by various techniques. Dynamic light scattering result indicated that size of magnesium nanoparticles is about 35 nm. X-ray diffraction showed that the produced sample consisted of hexagonal magnesium and amorphous carbon and there was no presence of magnesium oxides in the pattern. Field emission scanning electron microscopy and transmission electron microscopy results illustrated that the sample has morphology of agglomerated nanospheres. Energy dispersive X-ray spectroscopy demonstrated formation of 57 percent magnesium and 43 percent carbon. Differential scanning calorimetry analysis showed that the amorphous carbon increased ignition temperature of nanoparticles by 180 °C compared to pure magnesium micron-sized powder. Therefore, Mg–C nanoparticles can have many applications in different fields similar to magnesium nanopowders. However, by producing Mg–C nanoparticles, there is no need for vacuum chamber or inert gases during production and after that, since amorphous carbon protects magnesium nanoparticles from oxidation.     

Physical characterization of the polymorphic variations of magnesium stearate and magnesium palmitate hydrate species

The anhydrate, dihydrate, and trihydrate phases of chemically pure magnesium stearate and magnesium palmitate have been prepared and characterized as to their structural characteristics. The magnesium palmitate materials were obtained as significantly larger crystals than were the magnesium stearate materials, and the crystals of the dihydrate phase of either material were found to be the most fully developed. The crystal structures of all materials were judged to be very similar to each other, differing primarily in the magnitude of the long (001) crystal spacing. Thermal analysis studies revealed that the water of hydration contained within the dihydrate phases of either magnesium stearate or magnesium palmitate was more tightly bound than was the water of hydration within the corresponding trihydrate phases. These findings provide further support for the structural picture where the water contained in these lattice structures is present between the intermolecular planes.     

Contribution à l'étude du mécanisme de mûrissement de résines polyesters insaturées en présence de MgO

The thickening process for unsaturated polyester resin in styrene monomer and with magnesium oxide (MgO) has been evaluated by gel permeation chromatography (GPC). The GPC analysis n tetrahydrofuran (THF) shows that with time the distribution shifts towards higher molecular weight. This effect disappears when the products are analysed in a polar solvent. The process of thickening is attributed to the formation of reversible ionic association. The existence of strong ionic bonds in the final products is confirmed by the presence of a rubber-like plateau in dynamic mechanical properties. The effects of water and magnesium oxide concentrations are given.