激光回馈效应及其传感应用研究的进展

对基于激光回馈效应的传感应用研究进展进行了综述。由于激光回馈引起激光器功率波动一个条纹对应外部反射镜移动半个光波波长,功率波动深度与传统双光束干涉系统相当,基于该现象的激光回馈干涉仪与传统的干涉仪相比具有相同的相位灵敏度。但其结构简单、紧凑、易准直的特点,引起了国内外科研者浓厚的兴趣,开发了很多全新概念、经济实用的精密测量仪器。对激光回馈效应在位移测量、速度测量、振动测量、距离测量、角度测量和形貌测量中的原理进行了介绍,同时对各传感应用系统进行了评述。     

光纤SPR湿敏传感器及其共振光谱特性研究

提出并研制了基于光纤SPR传感探针的新型湿敏传感器。首先研究了光纤SPR传感探针对环境湿度变化的敏感特性,在此基础上提出在光纤SPR传感探针表面增覆不同厚度且具有水分子吸附功能的PVA薄膜来实现环境相对湿度的监测。研究结果表明,增覆双层PVA薄膜的光纤SPR传感探针在高湿区具有较好监测效果,其共振强度对应的相对湿度测量灵敏度达到1.59%/%RH,较光纤SPR探针呈现显著提高。而增覆单层PVA薄膜的光纤SPR传感探针在高湿区共振波长对应的相对湿度监测灵敏度达到2.411nm/%RH。此外所提出的新型光纤SPR湿敏探针在PVA薄膜失效后经过特殊工艺处理仍可重复镀膜使用。     

Phase-shift interferometry combined with surface plasmon resonance effect for two-dimensional bio-surface analysis

The phase-shift interferometry combined with surface plasmon resonance (SPR) effect has been studied as a novel technique used to analyze the bio-surface, which measures the spatial phase variation of SPR reflected light. The spatial sensitivity of the SPR imaging sensor is improved over the conventional SPR imaging systems based on optical intensity.     

反射式光纤表面等离子体波共振传感器特性研究

研究了一种基于表面等离子体波共振(SPR)光谱分析的折射率检测新方法。研究发现,表面等离子体波共振效应光谱特征的折射率灵敏度会随着液体性质变化而发生改变。根据折射率测量范围不同,分别选择共振波长和共振强度作为检测参量,实现理论折射率分辨力达到10~(-5)数量级以上。在理论分析和实验基础上,设计出一种基于共振光强检测的终端反射式光纤表面等离子体波共振效应传感系统,采用将传感信号和基准光信号的比值作为液体折射率变化的度量值。在1．3325～1．3991的折射率测量范围内,度量值与折射率之间呈现单调递减关系,线性相关系数为0．9983。通过定义耦合系数,还可实现对表面等离子体波共振效应效应强弱和变化趋势的评估。     

Controlling light by light with three-level atoms inside an optical cavity

We present our experimental demonstration of controlling the cavity output intensity of one laser beam with the intensity of another laser beam in a composite system consisting of a collection of three-level ?-type rubidium atoms and an optical ring cavity. When the intensity of the controlling beam is modulated with a square waveform, the cavity output power switches on and off (with a distinction ratio better than 20:1) between two steady-state values. This all-optical switching effect is the result of combined absorption and enhanced Kerr nonlinearity near resonance in such three-level atomic systems because of atomic coherence and can find applications in optical communication and optical computation.     

光纤光栅传感器阵列有源时域地址查询技术

报道了一种基于环形腔光纤激光器和1×4模拟电子开关的具备实时监测功能的光纤光栅传感网络查询技术,利用级联的波分复用光栅串充当环形腔光纤激光器端镜,借助可调法布里珀罗滤波器对反射的信号光进行扫描,调整光路结构并增加抽运光强度使信号光得到足够的增益,则可获得各传感元工作波长的激光脉冲,且依时序输出。又引入1×4模拟电子开关,将转换为电信号的激光输出按时序分配至4个输出信道。结合非平衡扫描干涉解调技术,实现了对4光栅传感阵列的查询解调。1555 nm波长时系统传感灵敏度的实验值为1.630°/με,与理论值1.674°/με基本吻合。     

High-Sensitivity Sensor Based on Surface Plasmon Resonance Enhanced Lateral Optical Beam Displacements

We present a new optical sensor based on surface plasmon resonance （SPIt） enhanced lateral optical beam displacements. Compared with the traditional SPIt methods, the new method provides higher sensitivity to the sensor system. Theoretical simulations show that the refractive index （RI） detection sensitivity of the SPR sensor based on the displacement measurement has a strong dependence on the thickness of the metal film. When the optimal thickness of the metal film is selected, the RI resolutlon of the SPIt sensor is predicted to be 2.2 × 10^-7 refractive index units （RIU）. Furthermore, it is found that the incidence angle can be used as a parameter to adjust the operating range of the sensor to different refractive index ranges.     

Intensity measurement based temperature-independent strain sensor using a highly birefringent photonic crystal fiber loop mirror

A fiber-optic strain sensor is demonstrated by using a short length of highly birefringent photonic crystal fiber (HiBi-PCF) as the sensing element inserted in a fiber loop mirror (FLM). Due to the ultralow thermal sensitivity of the HiBi-PCF, the proposed strain sensor is inherently insensitive to temperature. When a distributed-feedback (DFB) laser passes through the FLM, the output power is only affected by the transmission spectral change of the FLM caused by the strain applied on the HiBi-PCF. Based on intensity measurement, an optical power meter is adequate to deduce the strain information and an expensive optical spectrum analyzer (OSA) would not be needed.     

Experimental investigations on the external cavity time signature in chaotic output of an incoherent optical feedback external cavity semiconductor laser

Chaotic dynamics of a semiconductor laser subject to incoherent optical feedback (IOF) are experimentally investigated, and the external cavity time are retrieved and measured from intensity time series of the laser output by using self-correlation function and the mutual information. Through moderating feedback strength and injection current of the laser, the external cavity time signature of the laser chaotic output is effectively attenuated, and then the security of such chaos encryption system can be assured to a certain degree.     

Optical feedback characteristics in a dual-frequency laser during laser cavity tuning

The optical feedback characteristics in a Zeeman-birefringence dual-frequency laser are studied during the laser cavity tuning in three different kinds of optical feedback conditions: (i) only // -light is fed back; (ii) only ⊥-light is fed back; (iii) both lights are fed back.A compact displacement sensor is designed using the experimental result that there is a nearly 90 degrees phase delay between the two lights' cosine optical feedback signals when both lights are fed back into the laser cavity.The priority order that the two lights' intensity curves appear can be used for direction discrimination. The resolution of the displacement sensor is at least 79 nm, and the sensor can discriminate the target's moving direction easily.     

Optical feedback in a Zeeman-birefringence HeNe laser and its application in ranging

The optical feedback characteristics in a Zeeman-birefringence HeNe laser have been studied systematically when the external cavity varies in a large range. The intensity variations of the two orthogonally polarized lights are observed during the laser cavity tuning in the dual frequency laser. When the external cavity length is an integral multiple of the laser cavity length, either polarized light's intensity modulation depth varies not obviously when the laser works in dual modes conditions or single mode condition. But when the external cavity length is far away from an integral multiple of the laser cavity length and the laser works in different dual modes conditions, polarized light's intensity modulation depth varies obviously. This characteristic can guide us to tune the laser to work in single mode condition to improve the sensitivity of the optical system when the system is used for a large displacement measurement. It can also be used for measuring the position of the target mirror. The theoretical analysis is in good agreement with experimental results.     

基于FFP-TF2滤波器的可调谐激光器

可调谐激光器在光纤传感和光纤通信中有着广泛的应用,引起了人们的广泛重视。设计并搭建了基于FFP-TF2滤波器的可调谐激光器系统。通过FPGA设计的基于DDS (direct digital frequency synthesis)函数信号发生器与模拟放大电路结合产生的驱动电压,调节FFP-TF2腔长的变化,进而改变激光器的输出波长。该系统可以实现对FFP-TF2单点电压和扫描电压的驱动,从而激光器可以输出单波长激光和多波长扫描激光,在激光器输出波长1 532 nm~1 568 nm范围内,可以调节单波长输出,也可以调节多波长扫描范围,且两种模式可以切换使用。实验结果表明,激光器输出3 dB线宽基本保持在0.01 nm左右,激光器输出中心波长与驱动电压线性拟合度为99.934%,灵敏度为3.915 nm/V,而FFP-TF2输出中心波长与驱动电压线性拟合度为99.986%,灵敏度为4.021 nm/V,激光器输出中心波长相对FFP-TF2的误差为2.6%,说明该激光器系统输出波长具有线宽窄、稳定性好、灵活性高等优点。     

半导体激光器混沌输出的延时特征和带宽

外腔延时特征和带宽是影响混沌激光应用的两个重要参量.本文将一个单路光反馈的半导体激光器输出的激光部分地注入到另一个双路滤波光反馈的半导体激光器中,从而构成一个具有外光注入的双路滤波光反馈半导体激光器系统,即主从激光器系统,用于抑制混沌激光的延时特征并研究其带宽.数值研究了外光注入系数、反馈强度、抽运因子和滤波器带宽对系统输出混沌激光的延时特征的影响,然后将该系统对延时特征的抑制效果和具有外光注入的单路光反馈半导体激光器系统、具有外光注入的双路光反馈半导体激光器系统、具有外光注入的单路滤波光反馈半导体激光器系统以及无光注入双路滤波光反馈半导体激光器系统进行对比和分析,结果表明本文提出的方案对延时特征的抑制效果最好.然后在本文提出的具有外光注入的双路滤波光反馈半导体激光器系统中,延时特征被有效抑制的参数条件下研究系统输出混沌激光的带宽,结果表明,通过适当选择参数的取值,本文提出的方案可以提高系统输出混沌激光的带宽.     

基于Ring-down光学谐振腔的新型瓦斯传感器

提出将光谱吸收型传感技术和Ring-down光学谐振腔理论相结合的设计思路,将吸收光强与气体含量之间的定量关系与Ring-down光学谐振腔理论有机结合起来,设计了基于Ring-down光学谐振腔理论的光学瓦斯(甲烷)气体传感器气体吸收腔,以解决传统瓦斯传感器因为气体的谱宽很窄而难以提高微弱信号检测精度和灵敏度的问题....     

内置调制层型光纤表面等离子体波共振传感器研究

研究了一种基于内置调制层结构的光纤表面等离子体波共振(SPR)传感器。通过在金膜与纤芯的内侧增覆具有不同厚度和属性的光学透明薄膜作为内调制层,构成了性能独特的光电复合薄膜,起到调节倏逝波矢量和金膜表面等离子体振荡波矢量的双重作用,进而控制共振效应,为调节灵敏度提供依据。采用时域有限差分方法对内置调制层结构光纤SPR共振激励模型属性进行数值仿真。在此基础上,研制了用于液体折射率测量的内置调制层型光纤SPR传感探针。实验结果表明,该传感器在1.335～1.392折射率范围内,随着待测液体折射率的增大,SPR共振光谱向长波方向偏移,且灵敏度达到2263.1nm/RIU,与基于纤芯-金膜-环境介质三层结构的常规光纤SPR传感器相比提高一倍,能够更好地满足环境折射率检测的需求。     

表面等离子共振效应中传统近似理论与薄膜光学理论

指出Kretschmann模型的传统表面等离子共振公式在求解金属薄膜的参量时存在近似性,采用更为严密的薄膜光学理论,通过薄膜膜系的特征矩阵,得出表面等离子体共振衰减曲线.结果表明,表面等离子体共振近似理论与薄膜光学理论得到的共振角及反射率幅度存在差别;采用等高线图,给出了共振角差随着金属介电常量的变化规律.进一步的实验表明,薄膜光学理论所得模拟结果较表面等离子体共振近似理论与实验值吻合地更好,证明薄膜光学理论应用在表面等离子体共振效应要优于常用的近似理论.最后,采用两种理论对表面等离子体共振传感器进行优化设计,结果表明,两种理论所获得的高灵敏度分布区域差异较大,必须采用薄膜光学理论提供更精确的薄膜参量,来优化设计高灵敏度表面等离子体共振传感器.     

非本征敏感法布里-珀罗腔高精度光纤液位传感器输出特性

依据光学法布里珀罗(F-P)腔基本原理,分析了非本征敏感法布里珀罗腔光纤液位传感器工作原理及设计方案。实验结果表明,传感器具有良好的多周期输出特性和局部的线性特性,但法布里珀罗腔输出光强幅度随腔长增大逐渐衰减,传感器输出特性曲线中不同部分相同长度的线性工作区间却对应不同的测量量程和灵敏度。改变传感头中敏感组件的尺寸可满足对不同液位测量的需要。本传感器最大量程为20 m,精度为±0.5 mm,最小分辨力为0.3 mm。传感器特别适用于对易燃易爆液位精确测量,具有很强的实用性。     

Stabilization of a fiber Fabry–Perot interferometric acoustic wave sensor

Control of the operating point of an interferometric optical sensor to produce the highest sensitivity is crucial in the demodulation of interferometric optical sensors to compensate for Q point mismatching. A new method for operating point control of FFPI was discussed and demonstrated, the relationship of the F–P cavity length, the visibility and the interferometric fringe was analyzed. MCU was introduced to tracing the Q point by changing the laser wavelength through adjusting the light source temperature. It is proved that the dynamic range of the sensor system is surely extended; the NSR could be greatly improved because the wavelength change induced noises is greatly limited in this sensor system.     

Intensity modulation in single-mode microchip Nd：YAG lasers with asymmetric external cavity

Intensity modulation induced by the asymmetric external cavity in single-mode microchip Nd:YAG lasers is presented. Two kinds of experimental results are discussed based on multiple feedback effects. In one case, the intensity modulation curve is a normal sine wave, whose fringe frequency is four times higher than that of a conventional optical feedback system, caused by multiple feedback effects. In the other case, the intensity modulation curve is the overlapping of the above quadruple-frequency signal and conventional optical feedback signal, which is determined by the additional phase difference induced by the asymmetric external cavity. The theoretical analyses are in good agreement with the experimental results. The quadruple-frequency modulation of the laser output intensity can greatly increase the resolution of displacement measurement of an optical feedback system.     

Simulations of refractive index variation in a multimode interference coupler: Application to gas sensing

An optical sensor based on multimode interference couplers structures has been studied. We have introduced the optical parameters of materials used in existing optical integrated circuits and a sensitive material characterised in previous studies. The variation of optical properties such as the refractive index of the covering sensitive material leads to a modification of waveguiding conditions in the multimode interference coupler. A gas sensor can be developed by measuring the variation of light intensity at the output of the multimode interference coupler structure under gas exposure. Simulations have been performed in order to optimise the output light intensity variations to increase sensitivity. We have shown that these structures are more sensitive than Mach-Zehnder interferometers, and that the relation between dimensions and sensitivity of the multimode interference coupler is not trivial.