降低AWG插入损耗和串扰设计新方法

在AWG器件的设计中引入了抛物线型的楔形波导结构,根据过渡区理论优化了引入的抛物线型楔形结构的形状和尺寸.采用抛物线型楔形结构代替直线型楔形结构,AWG的插入损耗降低了2 dB左右.在优化参数时使输出/输入波导间距与阵列波导间距取不同的值,并使输出/输入波导间距适当增大,而阵列波导间距取较小值,这样使得串扰降至－30 dB以下且插入损耗保持在低水平.运用光束传播方法给出器件的输出光谱并证实了理论上预想的结果.     

A concise design of 16 × 16 polymer AWG with low insertion loss and crosstalk

In this paper, a 16-channel arrayed waveguide grating multiplexer (AWG) has been designed using polymer materials with 1.5% refractive index difference. Certain important parameters are optimized using the coupling mode theory and Beam Propagation Method. The factors that affect the insertion loss and the crosstalk are analyzed in this paper. In our design we introduced the parabolic taper structure and evaluated the suitable number of the arrayed waveguide, obtaining a total insertion loss of 2.19 dB. For obtaining a low crosstalk we evaluate the pitches of adjacent input/output waveguides ΔX and arrayed waveguides d as different values. We chose the value of ΔX about 2.5 times of d by enlarging the pitches of adjacent input/output waveguides. The crosstalk of the designed AWG is lower than −40 dB.     

Bidirectional WDM-PON architecture using a reflective filter and cyclic AWG

We proposed and demonstrated a bidirectional SCM-WDM PON using a reflective filter and cyclic AWG where up/downlink data could be provided using a single optical source. In the proposed scheme, the signal for downstream was modulated by a single CW laser diode and remodulated in the optical network unit as an upstream, the proposed WDM-PON scheme can offer the SCM signal for broadcasting service. In this paper, 1 Gb/s signals both for up- and downstream were demonstrated in 10 km bidirectional optical fiber link.     

小尺寸低折射率差硅基二氧化硅阵列波导光栅

随着阵列波导光栅(Arrayed Waveguide Grating,AWG)型器件在光通信系统中的大规模应用,对低成本AWG芯片的需求越来越多.在各种降成本方案中,减小AWG芯片的尺寸是最有效的方法之一.本文介绍了一种新型小尺寸低折射率差硅基二氧化硅AWG的设计.在该AWG中,输入波导/输出波导与平板波导连接的部分制...     

Performance analysis of metro WDM network based on an optical cross connects and arrayed waveguide grating demultiplexer

In this paper, we have demonstrated the quality-of-service offered by the metropolitan area network which is based on optical cross connect (OXC) and arrayed waveguide grating (AWG) demultiplexer operating at 10 Gb/s with 0.1 nm channel spacing for NRZ signal transmission. The data is successfully transmitted to a distance of 40 km with a reasonably good BER of 2.388 × 10⁻³⁵. The OXC and AWG demultiplexers in the proposed architecture allow incremental expansion in terms of the number of wavelength channels to be transmitted. Dispersion and crosstalk are the main signal-degrading factors arising from the operation of the OXC and the effectiveness of each factor is individually investigated.     

小尺寸低折射率差硅基二氧化硅阵列波导光栅

随着AWG型器件在光通信系统中的大规模应用,对低成本AWG芯片的需求越来越多。在各种降成本方案中,减小AWG芯片的尺寸是最有效的方法之一。本文介绍了一种新型小尺寸低折射率差硅基二氧化硅阵列波导光栅（AWG）的设计。在该AWG中,输入波导/输出波导与平板波导连接的部分制作成两侧为空气槽的高折射率差波导,所以在与输出平板波导连接处的相邻输出波导间距较小,这样可以在设计上缩短平板波导的长度、减少阵列波导的数量,实现较小的AWG芯片尺寸。该AWG的其它部分,如输入/输出波导与光纤耦合的部分、阵列波导光栅等均采用常规的低折射率波导工艺,所以就同时具有与常规的低折射率波导AWG相同的优点：如低耦合损耗、较好的串扰以及光学特性等。根据这个原理,设计了一种40通道100 GHz频率间隔的低折射率差硅基二氧化硅AWG,其芯片尺寸只有23.88 mm?10.5 mm,是传统相同材料制作的AWG尺寸的1/6。     

聚合物/二氧化硅混合型无热化阵列波导光栅参量的优化

研究一种新型无热化聚合物/二氧化硅混合波导组成的硅基二氧化硅阵列波导光栅.阵列波导光栅对温度的依赖性受波导物质的折射率和波导芯的尺寸影响.通过调节这些参量就可以减小温度对阵列波导光栅的影响.优化得到混合型阵列波导光栅在温度20~70℃范围内波谱漂移小于常规型 AWG结构的5%.     

Design of flat-field arrayed waveguide grating with three stigmatic points

A new-type flat-field arrayed waveguide grating (AWG), with the focal signals of all wavelengths of operation focusing along a straight line, has been designed. The work bases on the aberration theory of AWG, in which the restraints imposed on the conventional Rowland-type AWG have been released. In the design of flat-field AWG, three stigmatic points restrain three dominant geometry parameters: geometry of star couplers, ports distribution of phased-array, and length increment between adjacent paths. An eight-channel 200-GHz spacing flat-field AWG has been designed and simulated. As stigmatic points introduced, the aberration of this device is much lower than that of the Rowland-type AWG.     

A novel asymmetric arrayed waveguide grating with different lengths of input/output slabs

A novel arrayed waveguide grating (AWG) with asymmetric configuration is proposed. In this configuration, the length of the output slab region, the width and the spacing of the output waveguides are unequal to the corresponding parts of the input ones. Compared to a conventional symmetric AWG, the asymmetric AWG proposed in this paper has a smaller size without degrading its performance The analytic method used in a conventional symmetric AWG is extended to the asymmetric AWG. A design example of an asymmetric AWG with low insertion loss, low channel crosstalk and wide bandwidth is presented.     

Calculation of the spectral response of an arrayed-waveguide gating demultiplexer with a wide-angle beam propagation method in a cylindrical coordinate system

The spectral response of an arrayed-waveguide grating (AWG) demultiplexer is calculated by simulating the field propagation in the output section of an AWG with a wide-angle beam propagation method (BPM) in a cylindrical coordinate system. As in a practical design of an AWG demultiplexer, each output waveguide consists of two straight sections connected by a bending section. The spectral response obtained by the present algorithm is more accurate than those obtained with two popular approximate methods, namely, the conventional overlapped integral method and the standard BPM for radially straight and infinitely long output waveguides. With the present algorithm, the dependence of the spectral response on the parameters of the output section is analyzed. The channel crosstalk and the 3 dB passband width of the spectral response depend mainly on the length of the first straight section, the end separation and the angular separation of the output waveguides. The bending section results in an asymmetrical spectral response with remarkable sidelobes which can be reduced by increasing the bending radius.     

Design and analysis of nano-deep corrugated waveguide grating-based dual-resonant filters in visible and infra-red regions

A theoretical analysis of nano-deep corrugated long-period waveguide gratings on a SU-8 polymer-based channel waveguide with NOA61 optical epoxy coated upper- and lower cladding is presented. The transmission spectra of the gratings show strong rejection bands both at visible (at wavelength region of 450?460 nm) and infra-red (at wavelength region of 1530?1540 nm) regions when a grating period of ?68 μm with optimized grating tooth height is considered. Phase-matching graphs are studied to find the relationship between resonance wavelength and grating period. These results show that the grating parameters significantly affect the characteristics of transmission spectra as well as the resonance wavelength of the grating. Long-period waveguide grating-based band pass filter made by use of same polymer materials are also designed and analyzed. These types of waveguide grating-based filters can widely be used for visible and infra-red wavelength sensing applications.     

Design of wavelength adjustable lasers with photonic crystal based Fabry-Perot etalon for applications in optical network units of wavelength-division-multiplexed passive optical network systems

We propose a novel wavelength adjustable laser (WAL) with a photonic crystal based Fabry-Perot (FP) etalon. This laser will be a promising light source for optical network units (ONUs) of conventional wavelength-division-multiplexed passive optical network (WDM-PON) systems for up-stream transmission. It has the merits of a relatively simple fabrication and operation, wide process tolerance, low-cost, high side-mode suppression ratio, and wavelength-tunable characteristics. The optimization of the device structure and the implementation methods for this type of laser are discussed. Although the WALs in WDM-PON systems are not colorless, each laser can cover several wavelengths. Thus, the required number of different ONUs can be reduced. This approach may be necessary for 10 Gbps upstream transmission in next-generation optical access networks because the 10 Gbps data rate is difficult to achieve by using current colorless schemes.