多壁碳纳米管/十六烷基三甲基溴化铵修饰丝印电极的制备及大鼠血中雌二醇水平的测定

制备了多壁碳纳米管-十六烷基三甲基溴化铵(MWCNTs/CTAB)修饰丝印电极(MWCNTs-CTAB/SPE),并将其应用于大鼠血样中雌二醇(E2)的测定。在优化条件下,应用方波伏安法测定E2的氧化峰电流的线性范围为5.0×10~(-10)~1.0×10~(-8) mol/L(R=0.9968),检测限为5.0×10~(-11) mol/L。大鼠注射外源性E2后,MWCNTs-CTAB/SPE能特异性地测定血样中的E2,该方法与放射免疫测定法(RIA)比较,MWCNTsCTAB/SPE测定步骤简单,具有较好的准确度、精密度以及稳定性。     

肾上腺素在多壁碳纳米管修饰金电极上的电化学行为及测定

报道了一种测定肾上腺素的化学修饰电极和电化学分析方法。与裸金电极相比,刚果红改性的多壁碳纳米管修饰金电极可显著提高肾上腺素的氧化峰电流。实验优化了底液、pH值、修饰剂量、富集电位和富集时间等条件,建立了一种直接测定肾上腺素的高灵敏的电化学分析方法。该方法测定肾上腺素的线性范围为4.0×10-7~2.0×10-4mol.L-1;富集30 s后的检出限为8.5×10-8mol.L-1;对2.0×10-5mol.L-1的肾上腺素平行测定10次的相对标准偏差为4.9%。此方法已成功用于盐酸肾上腺素注射液中含量的测定。     

多壁碳纳米管修饰玻碳电极测定乙炔雌二醇

多壁碳纳米管修饰玻碳电极测定乙炔雌二醇;多壁碳纳米管;乙炔雌二醇;化学修饰电极;电化学测定     

多壁碳纳米管修饰电极测定非那西汀

本文研究了非那西汀在羧基化多壁碳纳米管修饰电极上的电化学行为。在0.1 mol·L-1HAc-NaAc(pH5.3)溶液中,非那西汀在羧基化多壁碳纳米管修饰电极上有一对可逆的氧化还原峰和一个氧化峰。对各种实验条件进行了优化,测得峰电流I p与非那西汀浓度在4.0×10-6~1.0×10-4mol·L-1范围内呈良好的线性关系,检测限为1.0×10-6mol·L-1。此修饰电极具有较好的重现性和稳定性。利用优化后的条件对尼美舒利药片进行了测定,测量值与标示值符合,回收率在96.5%~104.2%。     

去甲肾上腺素在多壁碳纳米管修饰玻碳电极上的电化学行为

动物体内的去甲肾上腺素(NE)含量变化反映了肢体神经系统植物交感神经的活动状况,在临床和基础研究中非常重要[1-3]。用化学修饰电极研究儿茶酚胺类神经递质的电化学行为以及对其进行测定是目前分析化学比较活跃的研究领域[4-6]。利用羧基化后的多壁碳纳米管(MWC-NT)对电极表面     

多壁碳纳米管修饰玻碳电极测定多巴酚丁胺的研究

研究了多巴酚丁胺在多壁碳纳米管修饰电极上的电化学行为,建立了一种直接测定多巴酚丁胺的电化学方法。在0.3mol·L-1H2SO4底液中,氧化峰电位为0.57V(vs.Ag/AgCl),峰电流与多巴酚丁胺的浓度在5.0×10-8～1.0×10-5mol·L-1范围内呈良好的线性关系。该法的检出限为3.0×10-8mol·L-1。平均回收率为99.15%。1.0×10-5mol·L-1多巴酚丁胺平行测定8次的标准偏差为4.8%。用拟定的方法测定了多巴酚丁胺注射液中多巴酚丁胺的含量,结果满意。     

多壁碳纳米管修饰电极的制备及其应用

研究了多壁碳纳米管修饰电极的制备方法及其对水飞蓟宾的电催化作用。利用循环伏安法和线性扫描法在乙醇-磷酸盐缓冲溶液中(pH=5.56)研究了水飞蓟宾的电化学特性。水飞蓟宾在多壁碳纳米管修饰电极上,于0.64 V处有一不可逆氧化峰,用线性扫描法建立了其定量方法,线性范围为2.0×10-6~1.0×10-4mol/L,检出限为4.4×10-7mol/L。利用该电极建立了水飞蓟宾的定性、定量方法,该法简便、快速、灵敏。     

纳米金修饰玻碳电极在抗坏血酸共存下选择性测定去甲肾上腺素

利用电沉积的方法制得纳米金修饰玻碳电极 ,该修饰电极对去甲肾上腺素 (NE)氧化反应有催化作用。去甲肾上腺素在纳米金修饰玻碳电极上有很强的吸附作用。研究了磷酸缓冲溶液的pH值和浓度对NE的电化学行为的影响。从去甲肾上腺素和抗坏血酸在纳米金修饰电极的循环伏安图上可观察到两个明显分开的氧化峰 ,峰电位差达到 1 3 1mV ,因此 ,可利用该修饰电极在抗坏血酸存在下选择性测定去甲肾上腺素 ,线性范围为 1× 1 0 - 4 ～5× 1 0 - 6 mol L。     

多壁碳纳米管-Nafion修饰电极测定左旋氧氟沙星

本文报道了用多壁碳纳米管-Nafion修饰玻碳电极测定痕量左旋氧氟沙星的方法。详细研究了左旋氧氟沙星在修饰电极上的电化学行为。实验表明,该电极对左旋氧氟沙星具有良好的电催化作用。在伏安图中,+1.73V处出现一灵敏氧化峰,利用该峰可进行左旋氧氟沙星的测定。在优化条件下,氧化峰电流与左旋氧氟沙星的浓度在0.001~0.5 mg.mL-1范围内成良好的线性关系。信噪比等于3时,检出限为1×10-4mg.mL-1。用于实际样品中左旋氧氟沙星的测定,加标回收率为97.32~102.82。     

多壁碳纳米管修饰金电极测定维生素B12

抗贫血药物维生素B12(VB12)俗称(氰)钴胺素,维生素B12是DNA合成的必需物质,若体内缺乏它,就会引起巨幼细胞贫血,高同型半胱氨酸血症和神经系统损害。因此,检测维生素B12可为血液系统和神经系统一些疾病的诊治提供依据[1],建立快捷简便的检测方法,在药物分析和医学检验中有应用价值。测定VB12的方法有高效液相色谱法[2]、荧光法[3]、毛细管电泳法[4]、伏安法[5]等。作者研究了VB12在碳纳米管修饰金电极上的电化学行为,并用以测定了VB12样品的含量,结果令人满意。1实验部分1.1仪器与试剂CHI618B电化学工作站(上海辰华仪器公司);KQ?400…     

基于对氨基苯硼酸修饰磁性纳米粒子及丝网印刷技术测定糖化血红蛋白

制备了对氨基苯硼酸修饰的磁性纳米粒子,其与血液中的糖化血红蛋白(Hb A1c)结合,通过网状玻璃态碳(RVC)电极的磁性区域后,可实现与未糖基化的血红蛋白分离。通过壳聚糖(CS)、正硅酸乙酯(TEOS)和碳纳米管构成的溶胶-凝胶膜修饰丝网印刷电极对血红蛋白进行电化学检测,从而建立了一种用于检测糖化血红蛋白的新方法。在0.10 V电位下,丝网印刷电极的电量与Hb A1c和Hb的浓度有较好的线性关系,检出限分别为6 mg/m L和0.05 mg/m L。该方法电极制作简单,有较好的重现性和稳定性,且能有效排除抗坏血酸(AA)、尿酸(UA)等的干扰,已成功应用于实际样品中Hb A1c的检测。     

丝印电极法体外筛选黄嘌呤氧化酶抑制剂方法研究

建立丝印电极快速筛选黄嘌呤氧化酶(XO)抑制剂的新方法. 利用丝网印刷技术制作一次性使用的丝印碳糊电极, 采用吸附法将羧基化的多壁碳纳米管(MWNTs)修饰在电极表面, 建立测定尿酸(UA)的简单快捷的计时电流分析方法, 将该法应用于XO抑制剂的体外筛选. 在0.3 V (vs. Ag/AgCl)的工作电位下, UA在MWNTs修饰的丝印电极上产生灵敏的响应电流, 响应时间30 s, 测定UA的线性范围为2～300 μmol•L^－1, 线性方程为Y (μmol•L^－1)＝43.8240X (μA)－0.1592, r＝0.9998, 最低检出限为1 μmol•L^－1. 用该法对4种中药水提物进行了筛选, 相对空白对照组, 桑寄生500 μg•mL^－1浓度组有显著性差异. 该法简单、快速, 电极制作成本低, 所需仪器简单, 适用于体外大量筛选XO抑制剂.     

丝网印刷修饰电极测量植物油的氧化诱导时间

制备了还原氧化石墨烯(rGO)、六氟磷酸1-丁基-3-甲基咪唑鎓(BMIMPF_6)和石墨相氮化碳(g-C3N4)修饰丝网印刷电极(SPME)。对SPME的修饰条件进行了优化,并采用循环伏安法和交流阻抗法对其电化学性能进行了表征。以1.0×10~(-3)mol/L LiCl-乙醇和三氯甲烷的混合液(体积比20∶3)为支持电解质溶液,利用电化学交流阻抗法测量红花籽油、杏仁油、小麦胚芽油和橄榄油的氧化诱导时间。F值和t值检验结果表明,SPME测得的植物油氧化诱导时间与国标法所测结果无系统性误差。该方法较国标法更简便、快速和灵敏。     

Fabrication of Silver Nanoparticles Decorated on Activated Screen Printed Carbon Electrode and Its Application for Ultrasensitive Detection of Dopamine

In the present study, we report the fabrication of silver nanoparticles (AgNPs) decorated on activated screen printed carbon electrode (ASPCE). The AgNPs were prepared by using Justicia glauca leaf extract as a reducing and stabilizing agent and the ASPCE was prepared by a simple electrochemical activation of screen printed carbon electrode (SPCE). The ASPCE/AgNPs shows a reversible electrochemical behaviour with enhanced response for DA than that of other modified SPCEs. Under optimum conditions, the electrochemical oxidation current response of DA is linear over the concentration range from 0.05 to 45.35 µM. The limit of detection is found as 0.017 µM with a high sensitivity of 7.85 µA µM^?1 cm^?2.     

Application of a Tetraamino Cobalt(II) Phthalocyanine Modified Screen Printed Carbon Electrode for the Sensitive Electrochemical Determination of L-Dopa in Pharmaceutical and Biological Samples

A novel synthesized tetraamino cobalt(II) phthalocyanine monomer was used for the fabrication of a sensor by electrochemical polymerization. A disposable electrochemical sensor based on the use of a screen printed carbon electrode covered with an electropolymerized film of tetraamino cobalt(II) phthalocyanine for the determination of L-dopa in pharmaceutical tablets and biological samples was described. Cyclic voltammetry and electrochemical impedance spectroscopy were performed for the characterization of the bare and modified electrode. For the electrochemical detection of L-dopa differential pulse voltammetry was used. The proposed method exhibits a good response towards electrooxidation of L-dopa in the linear concentration range: from 0.1 to 1000.0 μmol L⁻¹ in BRB pH=2.0, with a detection limit of 0.03 μmol L⁻¹ and from 1 to 1000 μmol L⁻¹ in PBS pH=7.4, with a detection limit of 0.33 μmol L⁻¹. Due to the fact that the developed sensor was applied in two different types of real samples, two buffer media were used, BRB pH=2.0 for pharmaceutical and urine samples and PBS pH=7.4 for whole blood samples. The proposed pCoTAPc/SPCE was successfully applied for the determination of L-dopa in pharmaceutical tablets, urine and in whole blood samples with satisfactory results.     

Voltammetric Detection of Captopril on Graphite Screen Printed Electrodes

We report the electrochemical detection of captopril on commercially available screen printed electrodes (GSPE); it exploits the silver residue left behind on a GSPE during its manufacturing process and involves the catalytic formation of the silver thiol complex (Ag⁺+RSH→AgSR+H⁺) at potentials corresponding to the oxidation of silver. The oxidation of the silver thiol complex was found to vary linearly with the captopril concentration up to 0.8 mM. A sensitivity of 13.34±0.58 μA mM^?1 is reported with a limit of detection of 4.27±0.18 μM.     

Voltammetric Determination of Cocaine Using Carbon Screen Printed Electrodes Chemically Modified with Uranyl Schiff Base Films

Chemically modified screen printed electrodes (CM‐SPE) using [UO₂(4‐MeOSalen)(H₂O)] ? H₂O films were employed in the voltammetric determination of cocaine. The chemical modification was performed by dip coating electrode surfaces (carbon, gold, and platinum) with methanolic solution containing the Schiff base complex with subsequent drying step at room temperature. The optimized amount of the chemical modifier over the working electrode was found to be 2.39 µg mm^?2 (geometric area). The voltammetric measurements were carried out in 50 : 50 v/v methanol:water solution containing 0.05 mol L^?1 KCl and 0.1 mol L^?1 LiCl as a supporting electrolyte without oxygen elimination by inert gas flow. The best results were obtained with carbon electrodes. Cocaine exhibits a well defined irreversible anodic peak current (i_pa) at a potential (E_pa) of 0.85 V vs Ag/AgCl. The current is directly proportional to the drug concentration. An optimal accumulation potential (E_prec), and time (t_prec) of ?0.80 V (vs Ag/AgCl), and 120 s, respectively, were determined. The linear dependence of i_pa with square root of scan rate (υ) indicates that the mass transport at the electrode surface is controlled by diffusion. An optimized scan rate of 100 mV s^?1 was obtained for analytical purposes. A limit of detection (LOD) and limit of quantification (LOQ) in 110 and 390 µmol L^?1, respectively, with intra and inter‐day repeatability of 2.61 % and 3.77 %, respectively, were obtained. In interference studies the proposed method demonstrated high specificity for cocaine in the presence of morphine and 3,4‐methylenedioxymethanphetamine. The above results demonstrate that this method provides a fast and low cost procedure for determination of cocaine in trace levels.     

Determination of Total PSA Using Magnetic Beads and a Re‐usable Screen Printed Carbon Electrode Array

A total PSA (tPSA) assay using magnetic beads (1 µm) and a re‐usable 8‐channel screen printed electrochemical array is here reported. The reaction scheme is based on a one step sandwich assay. The linear range obtained is comprised between 5 and 100 ng/mL of tPSA and have a limit of detection of 1.86 ng/mL. This methodology was validated, performing determination of tPSA in serum and the results were compared with a commercial ELISA kit.     

修饰丝网印刷电极的制备及抑郁小鼠大脑和血液样品中5-羟色胺含量的测定

制备了多壁碳纳米管和壳聚糖纳米复合材料(Multi-walled Carbon Nanotubes and Chitosan Nano-composites,MWCNTs-CHIN)修饰丝网印刷电极(MWCNTsCHIN/SPE),分别采用循环伏安法(CV)和方波伏安法(SWV)考察了5-HT在修饰丝网印刷电极上的电化学特性。在优化条件下,应用SWV法,5-羟色胺在0.30V处可产生灵敏的响应电流,且与其浓度呈线性,线性范围为0.01~1.00μmol/L,线性相关系数R为0.9969,检出限(S/N=3)为0.005μmol/L。用该方法测定慢性不可预见性应激抑郁模型(Chronic Unpredictable Mild Stress,CUMS)小鼠大脑和血液中5-HT的含量,结果表明,氟西汀组与空白组中5-HT的含量相当,模型组中5-HT的含量明显低于空白组(P0.01)。