高耐甲醇性和稳定性的纳米复合阴极催化剂

报导了一种由酞菁氧钛、铂金属纳米簇和氮杂化碳纳米角结构基元组装而成的新型纳米复合电化学催化剂(TiOPc-Pt/NSWCNH)的制备、表征及电催化性能. 在TiOPc-Pt/NSWCNH催化剂中, 氮杂化碳纳米角堆积形成多孔导电网络, 铂纳粒子均匀地分散于上述多孔导电网络中, 部分铂纳粒子与TiOPc微晶直接接触. 在甲醇存在的条件下, TiOPc-Pt/NSWCNH对氧还原反应表现出高催化活性和优良的选择性与稳定性. 在甲醇浓度为0.5 mol·L^-1的高氯酸水溶液中, TiOPc-Pt/NSWCNH催化氧还原反应的起始电位比商购Pt/C-JM催化剂提高了260 mV, 其质量活性和比活性(0.85 V (参比电极为可逆氢电极(RHE)))分别为83.5 A·g^-1和0.294 mA·cm^-2, 远高于Pt/C-JM催化剂. 在含氧气氛下, 于甲醇高氯酸水溶液中, 对TiOPc-Pt/NSWCNH和TiOPc-Pt/C催化剂进行了循环伏安法加速老化实验研究(0.6-1.0 V, 15000个循环), 结果表明TiOPc-Pt/NSWCNH具有更高的稳定性. TiOPc-Pt/NCNH催化剂的高耐醇性可能得益于由TiOPc微晶向Pt纳米粒子的电子转移, 其高稳定性主要得益于氮杂化碳纳米角的高石墨化程度及纳米角堆积而成网络结构.     

Meso-structured platinum thin films: active and stable electrocatalysts for the oxygen reduction reaction

Improving both the activity and the stability of the cathode catalyst in platinum-based polymer electrolyte fuel cells is a key technical challenge. Here, we synthesize a high surface area meso-structured Pt thin film that exhibits higher specific activity for the oxygen reduction reaction (ORR) than commercial carbon-supported Pt nanoparticles (Pt/C). An accelerated stability test demonstrates that the meso-structured Pt thin film also displays significantly enhanced stability as compared to the commercial Pt/C catalyst. Our study reveals the origin of the high turnover frequency (TOF), and excellent durability is attributed to the meso-structure, which yields a morphology with fewer undercoordinated Pt sites than Pt/C nanoparticles, a key difference with substantial impact to the surface chemistry. The improved catalyst activity and stability could enable the development of a high-performance gas diffusion electrode that is resistant to corrosion even under the harsh conditions of start-up, shut-down, and/or hydrogen starvation.     

高载量PtNi金属间化合物的氧还原电催化性能

采用改进的多元醇法制备了PtNi(原子比1∶1)质量分数为60%的高金属载量碳载PtNi合金(PtNi/C), 通过在450 ℃下退火处理获得了碳载PtNi金属间化合物氧还原电催化剂. 该催化剂对氧还原的质量比活性和面积比活性分别是商业化Pt/C(JM Pt/C)催化剂的1.66和2.3倍; 并且加速耐久性测试后PtNi金属间化合物催化剂的质量比活性仍与Pt/C的初始性能相当, 耐久性得到了大幅提升. PtNi/C金属间化合物催化剂氧还原活性和稳定性的提高归因于PtNi的有序原子排布结构及催化剂表面零价金属含量的提高.     

One-step synthesis of carbon-supported Pd–Pt alloy electrocatalysts for methanol tolerant oxygen reduction

A facile, one-step reduction route was developed to synthesize Pd-rich carbon-supported Pd–Pt alloy electrocatalysts of different Pd/Pt atomic ratios. As-prepared Pd–Pt/C catalysts exhibit a single phase fcc structure and an expansion lattice parameter. Comparison of the oxygen reduction reaction (ORR) on the Pd–Pt/C alloy catalysts indicates that the Pd₃Pt₁/C bimetallic catalyst exhibits the highest ORR activity among all the Pd–Pt alloy catalysts and shows a comparative ORR activity with the commercial Pt/C catalyst. Moreover, all the Pd–Pt alloy catalysts exhibited much higher methanol tolerance during the ORR than the commercial Pt/C catalyst. High methanol tolerance of the Pd–Pt alloy catalysts could be attributed to the weak adsorption of methanol induced by the composition effect, to the presence of Pd atoms and to the formation of Pd-based alloys.     

Trimetallic Au@PdPt core-shell nanoparticles with ultrathin PdPt skin as highly stable electrocatalysts for the oxygen reduction reaction in acid solution

To design efficient and low-cost core-shell electrocatalysts with an ultrathin platinum shell, the balance between platinum dosage and durability in acid solution is of great importance. In the present work, trimetallic Au@PdPt core-shell nanoparticles(NPs)with Pd/Pt molar ratios ranging from 0.31:1 to 4.20:1 were synthesized based on the Au catalytic reduction strategy and the subsequent metallic replacement reaction. When the Pd/Pt molar ratio is 1.19:1(designated as Au@Pd_(1.19) Pt_1 NPs), the superior electrochemical activity and stability were achieved for oxygen reduction reaction(ORR) in acid solution. Especially, the specific and mass activities of Au@Pd_(1.19) Pt_1 NPs are 1.31 and 6.09 times higher than those of commercial Pt/C catalyst. In addition, the Au@Pd_(1.19) Pt_1 NPs presented a good durability in acid solution. After 3000 potential cycles between 0.1 and 0.7 V(vs. Ag/AgCl), the oxygen reduction activity is almost unchanged. This study provides a simple strategy to synthesize highperformance trimetallic ORR electrocatalyst for fuel cells.     

A Nanoporous PdCo Alloy as a Highly Active Electrocatalyst for the Oxygen‐Reduction Reaction and Formic Acid Electrooxidation

A nanoporous (NP) PdCo alloy with uniform structure size and controllable bimetallic ratio was fabricated simply by one‐step mild dealloying of a PdCoAl precursor alloy. The as‐made alloy consists of a nanoscaled bicontinuous network skeleton with interconnected hollow channels that extend in all three dimensions. With a narrow ligament size distribution around 5 nm, the NP PdCo alloy exhibits much higher electrocatalytic activity towards the oxygen‐reduction reaction (ORR) with enhanced specific and mass activities relative to NP Pd and commercial Pt/C catalysts. A long‐term stability test demonstrated that NP PdCo has comparable catalytic durability with less loss of ORR activity and electrochemical surface area than Pt/C. The NP PdCo alloy also shows dramatically enhanced catalytic activity towards formic acid electrooxidation relative to NP Pd and Pd/C catalysts. The as‐made NP PdCo holds great application potential as a promising cathode as well as an anode electrocatalyst in fuel cells with the advantages of superior catalytic performance and easy preparation.     

具有优异甲醇耐受性的Rh掺杂PdCu有序金属间化合物纳米粒子增强氧还原电催化

Direct methanol fuel cells (DMFCs), as one of the important energy conversion devices, are of great interest in the fields of energy, catalysis and materials. However, the application of DMFCs is presently challenged because of the limited activity and durability of cathode catalysts as well as the poisoning issues caused by methanol permeation to the cathode during operation. Herein, we report a new class of Rh-doped PdCu nanoparticles (NPs) with ordered intermetallic structure for enhancing the activity and durability of the cathode for oxygen reduction reaction (ORR) and achieving superior methanol tolerance. The disordered Rh-doped PdCu NPs can be prepared via a simple wet-chemical method, followed by annealing to convert it to ordered phases. The results of transmission electron microscopy (TEM), scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS), power X-ray diffraction (PXRD) analysis and high resolution TEM (HRTEM) successfully demonstrate the formation of near-spherical NPs with an average size of 6.5 ± 0.5 nm and the conversion of the phase structure. The complete phase transition temperatures of Rh-doped PdCu NPs and PdCu are 500 and 400 ℃, respectively. The molar ratio of Rh/Pd/Cu in the as-synthesized Rh-doped PdCu NPs is 5/48/47. Benefitting from Rh doping and the presence of the ordered intermetallic structure, the Rh-doped PdCu intermetallic electrocatalyst achieves the maximum ORR mass activity of 0.96 A·mg^-1 at 0.9 V versus reversible hydrogen electrode (RHE) under alkaline conditions—a 7.4-fold enhancement compared to the commercial Pt/C catalyst. For different electrocatalysts, the ORR activities follow the sequence, ordered Rh-doped PdCu intermetallics > ordered PdCu intermetallics > disordered Rh-doped PdCu NPs > disordered PdCu NPs > commercial Pt/C catalyst. In addition, the distinct structure endows the Rh-doped PdCu intermetallics with highly stable ORR durability with unaltered half-wave potential (E_1/2) and mass activity after continuous 20000 cycles, which are higher than those of other electrocatalysts. Furthermore, the E_1/2 of the Rh-doped PdCu intermetallics decreases by only 5 mV after adding 0.5 mol·L^-1 methanol to the electrolyte, while the commercial Pt/C catalyst negatively shifts by 235 mV and a distinct oxidation peak can be observed. The results indicate that the ORR activity of the Rh-doped PdCu intermetallic electrocatalyst can be well maintained even in the presence of poisoning environment. Our results have demonstrated that Rh-doped PdCu NPs with ordered intermetallic structures is a potential electrocatalyst toward the next-generation high-performance DMFCs.     

钴-聚吡咯-碳载Pt催化剂的制备及其单电池性能研究

采用脉冲微波辅助化学还原法制备了钴-聚吡咯-碳载Pt催化剂(Pt/Co-PPy-C),并将其作为阴极催化剂,组装单电池。考察了电池运行温度和氢气/空气计量比对单电池性能的影响,并与商业Pt/C催化剂进行了耐久性实验比较。 结果表明,运行温度为70 ℃,氢气与空气的计量比为1.2:2.5时单电池性能最佳。600 mA/cm²恒电流稳定运行150 h耐久性测试中,以Pt/Co-PPy-C为阴极催化剂的单电池平均电压衰退率为0.119 mV/h,是商业Pt/C催化剂的26%。耐久性测试前后,单电池的阴极电荷传递阻抗为7.176和8.767 Ω,均比商业Pt/C催化剂阻抗小;Pt颗粒粒径从2.46 nm增长到3.18 nm,均小于商业Pt/C催化剂的粒径。这表明,以Pt/Co-PPy-C催化剂为阴极催化剂制备的单电池性能优良,在质子交换膜燃料电池中有广泛的应用前景。     

Pt单层修饰Pd/C氧还原催化剂

分别利用液相热解法和浸渍还原法制备了碳载钯纳米催化剂（Pd/C）,并研究了其对氧还原反应的电催化活性。与浸渍还原法相比,液相热解法得到的Pd/C催化剂虽然粒径较大,但表现出较好的氧还原反应（ORR）活性和稳定性.在所制备的Pd/C催化剂基础上,通过置换欠电势沉积的Cu原子单层,获得了Pt单层修饰的Pd/C催化剂,其ORR活性较Pd/C催化剂有显著提高,且与纯Pt/C催化剂接近,而其耐久性则较纯Pt/C催化剂有显著提升,显示出Pt单层催化剂的潜在优势.     

高活性和高稳定性的核壳结构PtPx@Pt/C催化氧还原

在质子交换膜燃料电池中,金属铂是最高效的阴极氧还原催化剂之一,但是铂昂贵的价格严重阻碍了其在燃料电池领域中的大规模商业化应用.通过铂与3d过渡金属(Fe、Co和Ni)合金化可以有效提高催化剂的氧还原活性,然而在实际的高腐蚀性、高电压和高温的燃料电池运行环境中,铂合金纳米粒子易发生溶解、迁移和团聚,从而导致催化剂耐久性差.同时过渡金属离子的溶出会影响质子交换膜的质子传导,并且一些过渡金属离子会催化芬顿反应,产生高腐蚀性?OH自由基,加快Nafion和催化剂的劣化.与过渡金属掺杂相比,非金属掺杂具有明显优势:一方面,非金属溶出产生的阴离子不会取代Nafion中的质子,也不会催化芬顿反应;另一方面,与3d过渡金属相比,非金属具有更高的电负性,其掺杂很容易调节Pt的电子结构.因此,本文通过非金属磷掺杂合成具有优异稳定性的核壳结构PtPx@Pt/C氧还原催化剂.通过热处理磷化商业碳载铂形成磷化铂(PtP2),经由酸洗处理产生富铂壳层,即PtPx@Pt/C.X射线粉末多晶衍射结果证明了PtP2相的存在,并且进一步通过电子能量损失谱对纳米粒子进行微区面扫描分析以及X射线光电子能谱分析证实了富铂壳层的存在,壳层厚度约1 nm.得益于核壳结构及磷掺杂引起的电子结构效应,PtP1.4@Pt/C催化剂在0.90 V(RHE)时的面积活性(0.62 mA cm–2)与质量活性(0.31 mAμgPt–1)分别是商业Pt/C的2.8倍和2.1倍.更重要的是,在加速耐久性测试中,PtP1.4@Pt/C催化剂在30000圈电位循环后质量活性仅衰减6％,在90000圈电位循环后仅衰减25％;而商业Pt/C催化剂在30000圈电位循环后就衰减46％.PtP1.4@Pt/C催化剂高活性与高稳定性主要归功于核壳结构、磷掺杂引起的电子结构效应以及磷掺杂增加了碳载体对催化剂粒子的锚定作用进而阻止了其迁移团聚.综上所述,本文为设计同时具有优异活性与稳定性非金属掺杂Pt基氧还原催化剂提供新的思路.     

Precisely Controlled Synthesis of Pt-Pd Octahedral Nanoframes as a Superior Catalyst towards Oxygen Reduction Reaction

Pt-based nanoframes represent a class of promising catalysts towards oxygen reduction reaction. Herein, we, for the first time, successfully prepared Pt-Pd octahedral nanoframes with ultrathin ridges less than 2 nm in thickness. The Pt-Pd octahedral nanoframes were obtained through site-selected deposition of Pt atoms onto the edge sites of Pd octahedral seeds, followed by selective removal of the Pd octahedral cores via chemical etching. Due to that a combination of three-dimensional opens geometrical structure and Pt-skin surface compositional structure, the Pt-Pd octahedral nanoframes/C catalyst shows a mass activity of 1.15 A/mg_Pt towards oxygen reduction reaction, 5.8 times enhancement in mass activity relative to commercial Pt/C catalyst (0.20 A/mg_Pt). Moreover, even after 8000 cycles of accelerated durability test, the Pt-Pd octahedral nanoframes/C catalyst still exhibits a mass activity which is more than three times higher than that of pristine Pt/C catalyst.     

新型钴-聚吡咯-碳载Pt燃料电池催化剂的制备与表征

采用脉冲微波辅助化学还原法制备了钴-聚吡咯-碳（Co-PPy-C）载Pt 催化剂（Pt/Co-PPy-C）,其中Pt 的总质量占20%. 利用透射电镜（TEM）、光电子射线能谱分析（XPS）和X射线衍射（XRD）研究了催化剂的结构,用循环伏安（CV）、线性扫描伏安（LSV）等方法考察了其电化学活性及氧还原反应（ORR）动力学特性及耐久性. Pt/Co-PPy-C电催化剂的金属颗粒直径约1.8 nm,略小于商用催化剂Pt/C（JM）颗粒尺寸（约2.5 nm）;催化剂在载体上分散均匀,粒径分布范围较窄. Pt/Co-PPy-C的电化学活性比表面积（ECSA）（75.1 m²·g^-1）高于商用催化剂的ECSA（51.3 m²·g^-1）. XPS测试表明,自制催化剂表面的Pt 主要以零价形式存在. 而XRD结果显示,自制催化剂中Pt（111）峰最强,Pt 主要为面心立方晶格. Pt/Co-PPy-C具有与Pt/C（JM）相同的半波电位;在0.9 V下,Pt/Co-PPy-C的比活性（1.21 mA·cm^-2）高于商用催化剂的比活性（1.04 mA·cm^-2）,表现出更好的ORR催化活性.动力学性能测试表明催化剂的ORR反应以四电子路线进行. CV测试1000 圈后,Pt/Co-PPy-C和Pt/C（JM）的ECSA 分别衰减了13.0%和24.0%,可见自制催化剂的耐久性高于商用Pt/C（JM）,在质子交换膜燃料电池（PEMFC）领域有一定的应用前景.     

Iron phthalocyanine coated on single-walled carbon nanotubes composite for the oxygen reduction reaction in alkaline media

Iron (II) phthalocyanine coated on single-walled carbon nanotubes was synthesized as a non-noble electrocatalyst for the oxygen reduction reaction (ORR). The composite exhibited higher activity than the commercial Pt/C catalyst, and excellent anti-crossover effect for methanol oxidation in the ORR.     

Improved lifetime of PEM fuel cell catalysts through polymer stabilization

A novel approach to increase lifetime of Pt/C catalysts was demonstrated and shown that Nafion-stabilized Pt catalyst (denoted here as Nafion-Pt/C) synthesized by a colloid route gives rise to an enhanced durability as compared to a conventional Pt/C catalysts commonly used in PEM fuel cell. A high catalytic activity of the catalyst is also observed by both CV (cyclic voltammetry) and ORR (oxygen reduction reaction) measurements. This catalyst durability in comparison with conventional Pt/C is increased directly by electrochemically-accelerated durability test (ADT). The loss rate of electrochemical active area (ECA) for Nafion-Pt/C catalysts is only 0.004 m² g⁻¹ cycle⁻¹, compared to a value of 0.012 m² g⁻¹ cycle⁻¹ for Pt/C. This indicates the catalyst is three times higher durability than Pt/C.     

Ion-exchange-assisted synthesis of Pt-VC nanoparticles loaded on graphitized carbon: a high-performance nanocomposite electrocatalyst for oxygen-reduction reactions

Carbide-based electrocatalysts are superior to traditional carbon-based electrocatalysts, such as the commercial Pt/C electrocatalysts, in terms of their mass activity and stability. Herein, we report a general approach for the preparation of a nanocomposite electrocatalyst of platinum and vanadium carbide nanoparticles that are loaded onto graphitized carbon. The nanocomposite, which was prepared in a localized and controlled fashion by using an ion-exchange process, was an effective electrocatalyst for the oxygen-reduction reaction (ORR). Both the stability and the durability of the Pt-VC/GC nanocomposite catalyst could be enhanced compared with the state-of-the-art Pt/C. This approach can be extended to the synthesis of other metal-carbide-based nanocatalysts. Moreover, this straightforward synthesis of high-performance composite nanocatalysts can be scaled up to meet the requirements for mass production.     

Carbon-supported ultrafine Pt nanoparticles modified with trace amounts of cobalt as enhanced oxygen reduction reaction catalysts for proton exchange membrane fuel cells

To accelerate the kinetics of the oxygen reduction reaction (ORR) in proton exchange membrane fuel cells, ultrafine Pt nanoparticles modified with trace amounts of cobalt were fabricated and decorated on carbon black through a strategy involving modified glycol reduction and chemical etching. The obtained Pt₃₆Co/C catalyst exhibits a much larger electrochemical surface area (ECSA) and an improved ORR electrocatalytic activity compared to commercial Pt/C. Moreover, an electrode prepared with Pt₃₆Co/C was further evaluated under H₂-air single cell test conditions, and exhibited a maximum specific power density of 10.27 W mg_Pt^?1, which is 1.61 times higher than that of a conventional Pt/C electrode and also competitive with most state-of-the-art Pt-based architectures. In addition, the changes in ECSA, power density, and reacting resistance during the accelerated degradation process further demonstrate the enhanced durability of the Pt₃₆Co/C electrode. The superior performance observed in this work can be attributed to the synergy between the ultrasmall size and homogeneous distribution of catalyst nanoparticles, bimetallic ligand and electronic effects, and the dissolution of unstable Co with the rearrangement of surface structure brought about by acid etching. Furthermore, the accessible raw materials and simplified operating procedures involved in the fabrication process would result in great cost-effectiveness for practical applications of PEMFCs.     

Stabilization of high-performance oxygen reduction reaction pt electrocatalyst supported on reduced graphene oxide/carbon black composite

Oxygen reduction reaction (ORR) catalyst supported by hybrid composite materials is prepared by well-mixing carbon black (CB) with Pt-loaded reduced graphene oxide (RGO). With the insertion of CB particles between RGO sheets, stacking of RGO can be effectively prevented, promoting diffusion of oxygen molecules through the RGO sheets and enhancing the ORR electrocatalytic activity. The accelerated durability test (ADT) demonstrates that the hybrid supporting material can dramatically enhance the durability of the catalyst and retain the electrochemical surface area (ECSA) of Pt: the final ECSA of the Pt nanocrystal on the hybrid support after 20?000 ADT cycles is retained at >95%, much higher than the commercially available catalyst. We suggest that the unique 2D profile of the RGO functions as a barrier, preventing leaching of Pt into the electrolyte, and the CB in the vicinity acts as active sites to recapture/renucleate the dissolved Pt species. We furthermore demonstrate that the working mechanism can be applied to the commercial Pt/C product to greatly enhance its durability.     

Ion‐Exchange‐Assisted Synthesis of Pt‐VC Nanoparticles Loaded on Graphitized Carbon: A High‐Performance Nanocomposite Electrocatalyst for Oxygen‐Reduction Reactions

Carbide‐based electrocatalysts are superior to traditional carbon‐based electrocatalysts, such as the commercial Pt/C electrocatalysts, in terms of their mass activity and stability. Herein, we report a general approach for the preparation of a nanocomposite electrocatalyst of platinum and vanadium carbide nanoparticles that are loaded onto graphitized carbon. The nanocomposite, which was prepared in a localized and controlled fashion by using an ion‐exchange process, was an effective electrocatalyst for the oxygen‐reduction reaction (ORR). Both the stability and the durability of the Pt‐VC/GC nanocomposite catalyst could be enhanced compared with the state‐of‐the‐art Pt/C. This approach can be extended to the synthesis of other metal‐carbide‐based nanocatalysts. Moreover, this straightforward synthesis of high‐performance composite nanocatalysts can be scaled up to meet the requirements for mass production.     

Highly stable PtP alloy nanotube arrays as a catalyst for the oxygen reduction reaction in acidic medium

Nanostructured Pt-metal alloys have shown impressive catalytic properties for the oxygen reduction reaction (ORR) in acidic medium, but their long-term stability has not been satisfactory. Herein, we look beyond the traditional Pt-metal alloys and have developed a new kind of Pt-nonmetal alloy electrocatalyst for the ORR. Specifically, the novel catalyst is composed of interconnected platinum monophosphide (PtP) alloy nanocrystals (∼3–4 nm) and featured supportless nanotube array morphologies. Due to the unique combination of composition and structure, the obtained PtP alloy nanotube arrays not only exhibited remarkable ORR activity, but also showed almost no degradation of the half-wave potential after accelerated durability tests. The result suggests that alloying Pt with a nonmetallic element (such as P) is indeed an effective approach to address the poor stability of Pt-based catalysts in acidic medium.     

Nanocrystalline tungstic carbide/graphitic carbon composite: synthesis,characterization, and its application as an effective Pt catalyst support for methanol oxidation

Tungsten carbide and graphitic carbon (WC/GC) composite has been synthesized by a simple solid-state pyrolysis method from an in situ route. The results indicate that the synthesized sample has a large specific surface area (S _BET) of 198 m² g^?1, and the WC nanoparticles (NPs) with a narrow particle size are well dispersed on the graphitic carbon. After loading Pt nanoparticles, the prepared Pt/WC/GC catalyst exhibits a mass activity of 416.1 mA mg^?1 Pt toward methanol electrooxidation, which is much higher than that of commercial Pt/C (JM) (231.2 mA mg^?1 Pt). Moreover, the onset potential is 100 mV more negative than that on Pt/C (JM) electrocatalyst. In addition, the Pt/WC/GC catalyst has stronger resistance to CO poisoning than the commercial Pt/C (JM). Its superior electrochemical performance could be attributed not only to the synergistic effect between Pt and WC NPs but also to the excellent electrical conductivity of GC and proper porous structure for desirable mass transportation in a porous electrode.