La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO2/Si衬底上制备出Bi4Ti3O12和Bi3.25La0.75Ti3O12薄膜,研究了La掺杂对Bi4Ti3O12薄膜的晶体结构、铁电性能和疲劳特性的影响,发现La掺杂没有改变Bi4Ti3O12薄膜的基本晶体结构,并且提高了Bi4Ti3O12铁电薄膜的剩余极化值和抗疲劳性能,对La掺杂改善Bi4Ti3O12铁电薄膜性能的机理进行了讨论.     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO₂/Si衬底上制备出Bi₄Ti₃O₁₂和Bi_3.25La_0.75Ti₃O₁₂薄膜，研究了La掺杂对Bi₄Ti₃O₁₂薄膜的晶体结构、铁电性能和疲劳特性的影响，发现La掺杂没有改变Bi₄Ti₃O₁₂薄膜的基本晶体结构，并且提高了Bi₄Ti₃O₁₂铁电薄膜的剩余极化值和抗疲劳性能，对La掺杂改善Bi₄Ti₃O₁₂铁电薄膜性能的机理进行了讨论. 关键词： 铁电性能 4Ti₃O₁₂薄膜')" href="#">Bi₄Ti₃O₁₂薄膜 3.25La_0.75Ti₃O₁₂薄膜')" href="#">Bi_3.25La_0.75Ti₃O₁₂薄膜 sol-gel法 La掺杂     

MOD法制备Bi4-xLaxTi3O12铁电薄膜及其谱图分析

采用有机金属沉积法(MOD)制备了Bi4Ti3O12(BIT)和Bi3.25La0.75Ti3O12(BLT)前驱体溶液,分别在单晶硅基片上制备了BIT和BLT铁电薄膜.前驱体溶液的干凝胶粉体和铁电薄膜分别用红外光谱(FTIR)、拉曼光谱和环境扫描电镜(ESEM)进行了表征.结果表明600℃时晶粒实现了由焦绿石相向类钙钛矿相结构的完全转变;温度升高,晶粒尺寸增大,薄膜结晶效果得到改善;引入镧使Ti-O和Bi-O键吸收峰位置向低波数频移,高温时频移率较大;500℃热处理时,干凝胶中乙二醇甲醚、乙酰丙酮完全分解,温度超过600℃后,残留的水及硝酸根离子挥发或分解.     

化学溶液法制备的Bi3.25La0.75Ti3 O12和Bi3.25Ndo.75 Ti3 O12薄膜的光学特性

采用化学溶液方法在(111)Pt/Ti/SiO2/Si衬底上制备了Bi3.25La0.75Ti3O12(BLT)和Bi3.25Nd0.75Ti3O12(BNT)薄膜.x射线衍射测试表明,两种薄膜都为单一的层状钙钛矿结构.扫描电子显微镜分析显示,BNT薄膜由大而均匀的棒状晶粒组成,BLT薄膜的组成晶粒则较小.采用紫外-近红外椭圆偏振光谱仪测试了200-1700nm波长范围的椭圆偏振光谱,拟合得到薄膜的光学常数(折射率和消光系数)和厚度,确定BLT和BNT薄膜的禁带宽度分别为4.30和3.61eV,并采用单电子振子模型分析了薄膜在带间跃迁区的折射率色散关系.     

Si基Bi3.25La0.75Ti3O12铁电薄膜的制备与特性研究

采用Sol-Gel工艺低温制备了Si基Bi_3.25La_0.75Ti₃O₁₂铁电薄膜.研究了退火温度对薄膜微观结构、介电特性与铁电性能的影响.500℃退火处理的Bi_3.25La_0.75Ti₃O₁₂薄膜未能充分晶化，晶粒细小且有非晶团聚，介电与铁电性能均较差.高于550℃退火处理的Bi_3.25La_{0.75 关键词： 铁电薄膜 3.25}La_0.75Ti₃O₁₂')" href="#">Bi_3.25La_0.75Ti₃O₁₂ Sol-Gel工艺     

退火气压对Bi3.25La0.75Ti3O12铁电薄膜的微观结构和铁电性能的影响

采用sol-gel法在Pt/TiO₂/SiO₂/p-Si(100)衬底上制备了Bi_3.25La_0.75Ti₃O₁₂(BLT)铁电薄膜,研究了在750 ℃时不同退火气压(p_{O2:10^-4—3 atm)对薄膜微观结构和电学性能的影响.XRD和拉曼光谱结果表明在10^-4和3 atm氧气压下退火 关键词： 3.25}La_0.75Ti₃O₁₂')" href="#">Bi_3.25La_0.75Ti₃O₁₂ 铁电性能 sol-gel法 正交化度     

(Bi,La)4Ti3O12-Sr(Bi,La)4Ti4O15共生结构铁电材料性能研究

采用固相烧结工艺，制备了不同La掺杂量(x=0.00，0.25，0.50，0.75，1.00，1.25和1.50) 的(Bi, La)₄Ti₃O₁₂-Sr(Bi, La)₄Ti4O₁₅ (SrBi_8-xLa_xT i₇O₂₇)共生结构铁电陶瓷样品.用x射线衍射对其进行微结构分析 ，并测量铁 关键词： 4Ti₃O₁₂-SrBi₄Ti₄O₁₅')" href="#">Bi₄Ti₃O₁₂-SrBi₄Ti_{4O15 La掺杂 铁电性能 居里温度 弛豫铁电}     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

Ag/Bi4Ti3O12栅n沟道铁电场效应晶体管制备及存储特性

在溶胶-凝胶工艺获得高质量Bi₄Ti₃O₁₂薄膜的基础上 ，制备了Ag/Bi₄Ti₃O₁₂栅n沟道铁电场效应晶体管. 研 究了Si基Bi₄Ti₃O₁₂薄膜的生长特性及其对铁电薄膜/ 硅的界面状态和铁电场效应晶体管存储特性的影响. 研究表明，在合理的工艺条件下可以获 得具有较高c-轴择优取向的纯钙钛矿相Si基Bi₄Ti₃O₁₂ 铁电薄膜并有利于改善Bi₄Ti₃O₁₂/Si之间的界面特性; 顺时针回滞的C-V特性曲线和C-T曲线表明Ag/Bi₄Ti₃O_{12栅n沟道铁电场效应晶体管具有极化存储效应和一定的极化电荷保持能力; 器件的转移(I< sub>sd}-V_G)特性曲线显示Ag/Bi₄Ti₃O_{12栅n沟道铁电场效应晶体管具有明显的栅极化调制效应. 关键词： 铁电场效应晶体管 4}Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 存储 特性 溶胶-凝胶工艺     

溶胶-凝胶法制备Sr2Bi4Ti5O18薄膜及其铁电性能研究

采用溶胶-凝胶法,在氧气氛中和层层晶化的工艺条件下,成功地制备了沉积在Pt/Ti/SiO₂/Si(100)衬底上的铁电性能优良的Sr₂Bi₄Ti₅O₁₈ (SBTi)薄膜,并研究了SBTi薄膜的微结构、表面形貌、铁电性能和疲劳特性.研究表明：薄膜具有单一的层状钙钛矿结构，且为随机取向；薄膜表面光滑，无裂纹，厚度约为725nm；铁电性能测试显示较饱和、方形的电滞回线，当外电场强度为275kV/cm时 关键词： 溶胶-凝胶法 铁电薄膜 2Bi₄Ti₅O₁₈')" href="#">Sr₂Bi₄Ti₅O₁₈     

化学溶液法制备的Bi3.25La0.75Ti3O12和Bi3.25Nd0.75Ti3O12薄膜的光学特性

采用化学溶液方法在(111)Pt／Ti/SiO2/Si衬底上制备了Bi3.25La0.75Ti3O12(BLT)和Bi3.25Nd0.75Ti3O12(BNT)薄膜．x射线衍射测试表明，两种薄膜都为单一的层状钙钛矿结构．扫描电子显微镜分析显示，BNT薄膜由大而均匀的棒状晶粒组成，BLT薄膜的组成晶粒则较小．采用紫外一近红外椭圆偏振光谱仪测试了200-100nm波长范围的椭圆偏振光谱，拟合得到薄膜的光学常数(折射率和消光系数)和厚度，确定BLT薄膜的禁带宽度分别为4．30和3．61eV，并采用单电子振子模型分析了薄膜在带间跃迁区的折射率色散关系．     

Sr2Bi4Ti5O18的压致结构相变

 使用4∶1的甲醇-乙醇混合液作传压介质，利用金刚石对顶砧装置（DAC），研究了层状铁电体Sr₂Bi₄Ti₅O₁₈的在位高压拉曼光谱和压致结构相变（0～27 GPa）。发现在8.31 GPa，Sr₂Bi₄Ti₅O₁₈经历了一次结构相交。在23.13 GPa以上，Sr₂Bi₄Ti₅O₁₈似乎出现了压致非晶相交的先兆。并使用内模方法对Sr₂Bi₄Ti₅O₁₈的内模进行了指认。     

退火处理对W:Bi4Ge3O12和Bi12GeO20晶体发光性能的影响

通过提拉法制备了W:Bi4 Ge3 O12和Bi12GeO20晶体,测试了晶体的吸收光谱、光致发光谱和发光衰减时间等.W:Bi4 Ge3 O12的可见光发光强度比纯Bi4 Ge3 O12有所增强,而且N2中退火处理对W:Bi4Ge3O12发光有进一步增强作用.Bi12GeO20在N2中退火处理后在745 nm附近有发光...     

Low temperature ferromagnetism in CaCu_3Ti_4O_(12)

The low-temperature magnetic order behaviors of perovskite oxide CaCu_3 Ti_4 O_(12)(CCTO) ceramics prepared by different methods are discussed.X-ray diffraction,scanning electron microscope,x-ray photoelectron spectroscopy,and direct current(DC) magnetization are used to characterize the structures,microscopic morphologies,valence states,and magnetic properties of the samples.The results show that the magnetic behaviors of CCTO ceramics are very sensitive to the preparation process.The quenched CCTO ceramic and CCTO powders grown in a molten salt crystal,which contain much more oxygen vacancies and Ti~(3+),show the coexistence of weak ferromagnetic order and antiferromagnetic order below the Neel temperature.It suggests that the bound magnetopolaron formed by oxygen vacancies and Ti~(3+) ion composite defects are responsible for the weak ferromagnetic order at low temperature.     

Bi4-xLax Ti3O12-SrBi4-y Lay Ti4O15共生结构铁电材料拉曼光谱研究

在常温下 ,对La掺杂共生结构铁电陶瓷Bi4 -xLaxTi3O1 2 _SrBi4 -yLayTi4 O1 5[BLT_SBLT(x y) ,x y =0 0 0 ,0 2 5 ,0 5 0 ,0 75 ,1 0 0 ,1 2 5 ,1 5 0 ]进行了拉曼光谱研究 .结果表明 ,在掺杂量低于 0 5 0时 ,La只取代类钙钛矿层中的Bi,当掺杂量高于 0 5 0后 ,部分La开始进入 (Bi2 O2 ) 2 层 .La取代 (Bi2 O2 ) 2 层中的部分Bi以后 ,(Bi2 O2 ) 2 层结构发生变化 ,原有的绝缘层和空间电荷库的作用减弱 ,导致材料剩余极化下降 .La掺杂量增至 1 5 0时 ,样品出现弛豫铁电性 ,这与 30cm- 1 以下模的软化相对应 ,说明La掺杂可引起材料的结构相变     

Electrical analysis of inter-growth structured Bi_4Ti_3O_(12)-Na_(0.5)Bi_(4.5)Ti_4O_(15) ceramics

Inter-growth bismuth layer-structured ferroelectrics(BLSFs), Bi_4Ti_3O_(12)-Na_(0.5)Bi_(4.5)Ti_4O_(15)(BIT-NBT), were successfully synthesized using the traditional solid-state reaction method. X-ray diffraction(XRD) Rietveld refinements were conducted using GSAS software. Good agreement and low residual are obtained. The XRD diffraction peaks can be well indexed into I2 cm space group. The inter-growth structure was further observed in the high-resolution TEM image. Dielectric and impedance properties were measured and systematically analyzed. At the temperature range 763-923 K(below T_c), doubly ionized oxygen vacancies(OVs) are localized and the short-range hopping leads to the relaxation processes with an activation energy of 0.79-1.01 eV. Above T_c, the doubly charged OVs are delocalized and become free ones, which contribute to the long-range dc conduction. The reduction in relaxation species gives rise to a higher relaxation activation energy ~ 1.6 eV.     

光折变晶体钛酸秘的折射率和光学均匀性的测量

本文报导光折变晶体钛酸铋的折射率和光学均匀性的测量结果。     

Bi4-xLaxTi3O12-SrBi4Ti4O15,共生结构铁电材料拉曼光谱研究

在常温下，对La掺杂共生结构铁电陶瓷Bi_4-xLa_xTi_3O_12-SrBi_4-yLayTi_4O_15［BLT-SBLT(x+y),x+y= 0.00, 0.25,0.50,0.75,1.00,1.25,1.50］进行了拉曼光谱研究.结果表明，在掺杂量低于0.50时，La只取代类钙钛矿层中的Bi，当掺杂 量高于0.50后，部分La开始进入(Bi_2O_2)^2+层. La取代(Bi_2O_2)^2+层中的部分Bi以后，(Bi_2O_2)^2+层结构发生变化 ，原有的绝缘层和空间电荷库的作用减弱，导致材料剩余极化下降. La掺杂量增至1.50时，样品出现弛豫铁电性，这与30cm^-1以下模的软化相对应，说明La掺杂可引起材料 的结构相变. 关键词： Bi4-xLaxTi3O12-SrBi4Ti4O15 La掺杂 声子模 拉曼频移     

Bi12SiO20类晶体中全息图记录和读出的双施主模型

用双施主模型对Ｂｉ１２ＳｉＯ２０（ＢＳＯ）光致折射晶体中全息图记录和读出的Ｋｕｋｈｔａｒｅｖ单施主模型进行了修正。并用以讨论了全息图的衍射率，得到一个描述衍射率的普遍公式。     

Nanoscale domain switching mechanism of Bi_(3.15)Eu_(0.85)Ti_3O_(12) thin film under the different mechanical forces

The switching process of ferroelectric thin films in electronic devices is one of the most important requirements for their application. Especially for the different external fields acting on the film surface, the mechanism of domain switching is more complicated. Here we observe the nanoscale domain switchings of Bi3.15Eu0.85Ti3O12 thin film under different mechanical forces at a fast scan rate. As the force increases from initial state to 247.5 n N, the original bright or grey contrasts within the selected grains are all changed into dark contrasts corresponding to the polarization vectors reversed from the up state to the down state, except for the clusters. As the mechanical force increases to 495 n N, the color contrasts in all of the selected grains further turn into grey contrasts and some are even changed into grey contrasts completely showing the typical 90° domain switching. When another stronger loading force 742.5 n N is applied, the phase image becomes unclear and it indicates that the piezoelectric signal can be suppressed under a sufficiently high force, which is coincident with previous experimental results. Furthermore, we adopt the domain switching criterion from the perspective of equilibrium state free energy of ferroelectric nanodomain to explain the mechanisms of force-generated domain switchings.