Silver particles-modified polysulfonic acid-doped polyaniline layers: electroless deposition of silver in slightly acidic and neutral solutions

Polyaniline layers are produced by electrochemical polymerisation of aniline in the presence of small amounts of poly(2-acryalamido-2-methyl-propane-sulfonic acid) in an inorganic acid solution. Electroactivity and in situ conductance of the obtained polysulfonic acid-doped layers are studied in slightly acidic and neutral solutions. Electroless deposition of silver particles is carried out in silver-EDTA complex ion solutions at pH = 4.2 and pH = 6.6 by using the polyaniline layers as reductant. The amount of electroless-deposited silver is studied depending on: polymerisation charge used to synthesize the polymer layer, pH of the plating solution, metal ion concentration and dipping time. SEM shows in all cases a highly non-homogeneous distribution of the metallic phase over the surface, the most protruding fibrillar polymer structures favouring the electroless silver deposition. A linear dependence between amount of the polyaniline material and amount of deposited silver is found for the silver plating solutions with the highest investigated concentration (10 mmol l⁻¹). At lower concentrations (2.0 and 0.4 mmol l⁻¹), the same amount of silver becomes deposited on polymer layers with markedly different charges. The electroless deposition of silver in the solutions with lower acidity results in lower amounts of deposited silver at otherwise identical conditions. Effects such as charge transfer within the polymer phase and mass transport in the solution are addressed to explain the observed dependencies of the amount of deposited silver on concentration and pH in the different plating solutions.

     

Silver particles-modified polysulfonic acid-doped polyaniline layers: electroless deposition of silver in slightly acidic and neutral solutions

Polyaniline layers are produced by electrochemical polymerisation of aniline in the presence of small amounts of poly(2-acryalamido-2-methyl-propane-sulfonic acid) in an inorganic acid solution. Electroactivity and in situ conductance of the obtained polysulfonic acid-doped layers are studied in slightly acidic and neutral solutions. Electroless deposition of silver particles is carried out in silver-EDTA complex ion solutions at pH????.2 and pH????.6 by using the polyaniline layers as reductant. The amount of electroless-deposited silver is studied depending on: polymerisation charge used to synthesize the polymer layer, pH of the plating solution, metal ion concentration and dipping time. SEM shows in all cases a highly non-homogeneous distribution of the metallic phase over the surface, the most protruding fibrillar polymer structures favouring the electroless silver deposition. A linear dependence between amount of the polyaniline material and amount of deposited silver is found for the silver plating solutions with the highest investigated concentration (10?mmol?l^??). At lower concentrations (2.0 and 0.4?mmol?l^??), the same amount of silver becomes deposited on polymer layers with markedly different charges. The electroless deposition of silver in the solutions with lower acidity results in lower amounts of deposited silver at otherwise identical conditions. Effects such as charge transfer within the polymer phase and mass transport in the solution are addressed to explain the observed dependencies of the amount of deposited silver on concentration and pH in the different plating solutions.     

Synthesis and electrochemical properties of composite films based on poly-3,4-ethylenedioxythiophene with inclusions of silver particles

The electrochemical behavior of PEDOT/Ag composite films obtained by chemical deposition of ultrafine Ag particles into the poly-3,4-ethylenedioxythiophene (PEDOT) matrix was studied. The film morphology was characterized by transmission electron microscopy (TEM). The changes in the mass of the films during the chemical deposition of silver into the polymer structure were evaluated microgravimetrically. The mass of the included metallic silver particles depends on the synthesis time and the initial concentration of silver ions in solution. The cyclic voltammograms (CVs) of PEDOT/Ag films in sodium nitrate solutions and sodium nitrate solutions with additions of chloride ions were studied. The cyclic voltammograms of PEDOT/Ag films in chloride-containing solutions showed the peaks of the oxidation of silver and reduction of the oxidation product, which were absent on the CVs of the starting PEDOT film.     

Conductive paper through LbL multilayering with conductive polymer: dominant factors to increase electrical conductivity

A conductive paper was made of cellulose fibers with a multilayer of polyethyleneimine (PEI) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and the factors to increase the conductivity of the paper were investigated. The adsorption amount and the structure of PEI and PEDOT:PSS multilayer was changed by controlling salt concentration and the number of layers, and inter-contact degree of fibers was controlled by calendering. The adsorption behavior of the polyelectrolytes onto cellulose was evaluated using a quartz crystal microbalance with dissipation monitoring, and the adsorption amount was quantitatively analyzed through Kjeldahl nitrogen analysis and an Inductively Coupled Plasma Optical Emission Spectrometer. The conductivity of the resultant paper was in the range of 10^?5–10^?4 S/cm without loss of paper strength. The conductivity of the paper increased when the multilayer was formed at low salt concentration and the conductive paper was calendered. It appeared that electron transfer by increased contact between PEDOT:PSS improved the conductivity of the paper.     

用化学镀法制备 Pd/Ag 膜时膜厚和组成的控制

 研究了不同 Pd2+含量的镀液在多孔陶瓷载体上的化学沉积规律, 发现当 Pd 沉积层厚度达到约 5 μm 后, 即使镀液中反应物的消耗比例很小, 膜厚增长也明显变缓, 沉积反应主要受膜层表面的催化活性位控制; 当镀液中 Pd2+含量只能沉积形成小于 4 μm 的 Pd 膜时, 在 323 K 化学镀 180 min 后, 镀液中 Pd2+的转化率高于 90%. 与之相似, 当 Ag 镀液中的 Ag+含量等于 0.5~2 μm 的 Ag 膜层所需量时, 在 333 K 化学镀 120 min 后, Ag+的转化率可达 95%. Ag+的高转化率与 Ag 颗粒的择向生长特性有关. 根据 Pd 和 Ag 的化学镀沉积规律, 通过调节镀液中金属离子的含量能够预先设计和精确控制超薄 Pd/Ag 膜的膜厚和组成.     

Synthesis and characterization nanocomposite of polyacrylamide‐rGO‐Ag‐PEDOT/PSS hydrogels by photo polymerization method

We present a novel approach to the fabrication of advanced polymeric nanocomposite hydrogels from polyacrylamide (PAAm) by incorporation of graphene‐silver‐polyethylenedioxythiophene‐polystyrene sulfonate (rGO‐Ag‐PEDOT/PSS) by photopolymerization method. Infrared spectroscopy was employed to characterize the structure of the hydrogels. The internal network structure of nanocomposite hydrogels was investigated by scanning electron microscope. Swelling, deswelling, and mechanical properties of the hydrogels were investigated. The compressive strength of nanocomposite hydrogels reaches maximum of 1.71 MPa when the ratio of rGO‐Ag‐PEDOT/PSS to PAAm was 0.3 wt%, which is 1.57 times higher than that of PAAm hydrogels (1.09 MPa). The electrical conductivity of the PAAm‐rGO‐Ag‐PEDOT/PSS hydrogel was found to be 3.91 × 10^?5 S cm^?1. Copyright © 2015 John Wiley & Sons, Ltd.     

A Role of the Plating Regime in the Deposition of Bismuth Films onto a Carbon Paste Electrode. Microscopic Study

A microscopic study is presented based on observations of bismuth films deposited from various plating solutions and under different experimental conditions onto the carbon paste surface. Electrolytic plating of bismuth films was performed either as simulation of preconcentration in‐situ from a 0.2 M acetate buffer containing 5×10^?5 M Bi³⁺ (pH 4.25), or as external deposition from various plating solutions: 0.1 M acetate buffer with 5×10^?4 M Bi³⁺ (pH 4.50), 0.5 M HCl with either 0.001 M BiCl₃ or 0.005 M BiCl₃ , 0.5 M HCl+0.5 M KBr+0.005 M BiCl₃ , and 0.5 M HCl+0.5 M KI+0.005 M BiCl₃ (all pH≈0.5). Scanning electron microscopic images of the bismuth films showed a considerable variability in structure and compactness of the deposited layer in dependence on experimental conditions chosen such as the concentration of Bi(III) species, the total acidity of plating media, the stability of complexes of Bi(III) with halogenide anions or the deposition potential applied.     

Roll‐to‐Roll printed PEDOT/PSS/GO Plastic Film for Electrochemical Determination of Carbofuran

In this work, we developed a roll‐to‐roll printed poly(3,4‐ethylenedioxythiophene)/polystyrene sulphoanate without graphene oxide (GO) (PEDOT/PSS) and with graphene oxide (PEDOT/PSS/GO) plastic films for the electrochemical determination of carbofuran. Both the PEDOT/PSS and PEDOT/PSS/GO plastic films showed electroactivity towards the oxidation of carbofuran. Incorporation of graphene oxide (GO) improves the electrochemical activity of carbofuran and increased its sensitivity. The printed plastic films were characterized by cyclic voltammetry (CV), linear sweep voltammetry (LSV), surface profilometer, four point probe and atomic force microscopy (AFM). The effects of pH, deposition time, deposition potential and film thickness on the oxidation peak current of carbofuran were investigated. Under the optimized conditions, a dynamic linear range of 1 μM–90 μM with a detection limit of 1.0×10^?7 M (S/N=3) were obtained. The printed PEDOT/PSS/GO plastic electrode was applied for the determination of carbofuran in vegetable and fruit samples with recoveries between 94.4 and 101.8 %.     

Separation of traces of silver from palladium by a surface replacement reaction

An effective method has been developed for the enrichment of silver traces in palladium and of carrier-free¹¹¹Ag formed in it by thermal neutron capture and subsequent β-decay. A replacement reaction occurring between hydrogen atoms absorbed in metallic palladium and cations in aqueous solution has been observed. A new device is proposed for the measurement of hydrogen absorbed by finely divided palladium without the necessity of removing it from the metal. Both palladium and silver ions were quantitatively and selectively deposited in the presence of other cations from hydrochloric acid solutions, whereas the deposition proved to be selective and quantitative for silver from ammoniacal solutions. About 0.4 ppm silver in specpure palladium can be removed by this method. A practical example of a more than 500-fold enrichment of silver traces in palladium is described.     

Flexible conducting polymer transistors with supercapacitor function

Planar organic electrochemical transistors (OECTs) using PEDOT:PSS as the channel material and nanostructured carbon (nsC) as the gate electrode material and poly(sodium 4‐styrenesulfonate (PSSNa) gel as the electrolyte were fabricated on flexible polyethylene terephthalate (Mylar^®) substrates. The nsC was deposited at room‐temperature by supersonic cluster beam deposition (SCBD). Interestingly, the OECT acts as a hybrid supercapacitor (to give a device that we indicate as transcap). The energy storage ability of transcaps has been studied with two cell configurations: one featuring PEDOT:PSS as the positive electrode and nsC as the negative electrode and another configuration with reversed electrode polarity. Potentiostatic charge/discharge studies show that both supercapacitors show good performance in terms of voltage retention, in particular, when PEDOT:PSS is used as the positive electrode. Galvanostatic charge–discharge characteristics show typical symmetric triangular shape, indicating a nearly ideal capacitive behavior with a high columbic efficiency (close to 100%). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 96–103     

Lithium Polystyrene Sulfonate as a Hole Transport Material in Inverted Perovskite Solar Cells

Despite the exceptional efficiency of perovskite solar cells (PSCs), further improvements can be made to bring their power conversion efficiencies (PCE) closer to the Shockley-Queisser limit, while the development of cost-effective strategies to produce high-performance devices are needed for them to reach their potential as a widespread energy source. In this context, there is a need to improve existing charge transport layers (CTLs) or introduce new CTLs. In this contribution, we introduced a new polyelectrolyte (lithium poly(styrene sulfonate (PSS))) (Li:PSS) polyelectrolyte as an HTL in inverted PSCs, where Li⁺ can act as a counter ion for the PSS backbone. The negative charge on the PSS backbone can stabilize the presence of p-type carriers and p-doping at the anode. Simple Li:PSS performed poorly due to poor surface coverage and voids existence in perovskite film as well as low conductivity. PEDOT:PSS was added to increase the conductivity to the simple Li:PSS solution before its use which also resulted in lower performance. Furthermore, a bilayer of PEDOT:PSS and Li:PSS was employed, which outperformed simple PEDOT:PSS due to high quality of perovskite film with large grain size also the large electron injection barrier (ϕ_e) impeded back diffusion of electrons towards anode. As a consequence, devices employing PEDOT:PSS / Li:PSS bilayers gave the highest PCE of 18.64%.     

导电高分子PEDOT/PSS保护银纳米颗粒的制备与表征

利用导电高分子聚(3,4-二氧乙基噻吩)/聚(对苯乙烯磺酸)(PEDOT/PSS)作保护剂,制备了银纳米颗粒,用UV-Vis和TEM对其进行了表征.结果表明,选择合适量的PEDOT/PSS保护剂可以得到大小分布较窄银纳米颗粒.     

聚3,4-乙烯二氧噻吩/石墨烯/钛电极的制备及其电化学性能

采用直流电弧等离子体喷射化学气相沉积法把石墨烯生长在钛(Ti)基底上,并采用电化学氧化聚合法在石墨烯表面沉积聚3,4-乙烯二氧噻吩(PEDOT),由此构造PEDOT/石墨烯/Ti电极。形貌及结构表征结果表明,电聚合200圈以上的PEDOT呈线状或泡沫状且均匀分布于石墨烯表面。电化学性能测试结果表明,PEDOT/石墨烯/Ti电极具有高的比电容和库伦效率;其电聚合次数为400圈时,与PEDOT/Ti电极相比,比电容提高42倍,其最大电势窗口可达1.4 V,而在0～1.2 V电势窗口范围内,扫描速度为10 mV·s-1时,比电容可达到269.6 mF·cm-2。     

Free‐Standing Conducting Polymer Films for High‐Performance Energy Devices

Thick, uniform, easily processed, highly conductive polymer films are desirable as electrodes for solar cells as well as polymer capacitors. Here, a novel scalable strategy is developed to prepare highly conductive thick poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (HCT‐PEDOT:PSS) films with layered structure that display a conductivity of 1400 S cm^?1 and a low sheet resistance of 0.59 ohm sq^?1. Organic solar cells with laminated HCT‐PEDOT:PSS exhibit a performance comparable to the reference devices with vacuum‐deposited Ag top electrodes. More importantly, the HCT‐PEDOT:PSS film delivers a specific capacitance of 120 F g^?1 at a current density of 0.4 A g^?1. All‐solid‐state flexible symmetric supercapacitors with the HCT‐PEDOT:PSS films display a high volumetric energy density of 6.80 mWh cm^?3 at a power density of 100 mW cm^?3 and 3.15 mWh cm^?3 at a very high power density of 16160 mW cm^?3 that outperforms previous reported solid‐state supercapacitors based on PEDOT materials.     

Conductivity enhancement of PEDOT:PSS film via sulfonic acid modification: application as transparent electrode for ITO-free polymer solar cells

3-Hydroxy-1-propanesulfonic acid(HPSA)was applied as a modification layer on poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS)film via spin-coating,resulting in a massive boost of the conductivity of PEDOT:PSS film,and thus the as-formed PEDOT:PSS/HPSA bilayer film was successfully used as a transparent electrode for ITO-free polymer solar cells(PSCs).Under the optimized concentration of HPSA(0.2 mol L~(-1)),the PEDOT:PSS/HPSA bilayer film has a conductivity of 1020 S cm~(-1),which is improved by about 1400 times of the pristine PEDOT:PSS film(0.7 S cm~(-1)).The sheet resistance of the PEDOT:PSS/HPSA bilayer film was 98Ωsq~(-1),and its transparency in the visible range was over 80%.Both parameters are comparable to those of ITO,enabling its suitability as the transparent electrode.According to atomic force microscopy(AFM),UV-Vis and Raman spectroscopic measurements,the conductivity enhancement was resulted from the removal of PSS moiety by methanol solvent and HPSA-induced segregation of insulating PSS chains along with the conformation transition of the conductive PEDOT chains within PEDOT:PSS.Upon applying PEDOT:PSS/HPSA bilayer film as the transparent electrode substituting ITO,the ITO-free polymer solar cells(PSCs)based on poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)]:[6,6]-phenyl C71-butyric acid methyl ester(PC_(71)BM)(PCDTBT:PC_(71)BM)active layer exhibited a power conversion efficiency(PCE)of 5.52%,which is comparable to that of the traditional ITO-based devices.     

Water soluble amino grafted silicon nanoparticles and their use in polymer solar cells

Stable aqueous amino-grafted silicon nanoparticles(SiNPs-NH2) were prepared via one-pot solution method. By grafting amino groups on the particle surface, the dispersion of SiNPs in water became very stable and clear aqueous solutions could be obtained. By incorporating SiNPs-NH2 into the hole transport layer of poly(3,4-ethylenedioxythiophene)/polystyrene sulfonic acid(PEDOT:PSS), the performance of polymer solar cells composed of poly[2-methoxy,5-(2'-ethylhexyloxy)-1,4-phenylene vinylene](MEH-PPV):[6,6]-phenyl-C61-butyric acid methyl ester(PCBM) as active layer can be improved. SiNPs-NH2 are dispersed uniformly in the PEDOT:PSS solution and help form morphologies with small-sized domains in the PEDOT:PSS film. SiNPs-NH2 serve as screens between conducting polymer PEDOT and ionomer PSS to improve the phase separation and charge transport of the hole transport layer. As a result, the sheet resistance of PEDOT:PSS thin films is decreased from(93 ± 5) × 105 to(13 ± 3) × 105 ?/□. The power conversion efficiency(PCE) of polymer solar cells was thus improved by 9.8% for devices fabricated with PEDOT:PSS containing 1 wt% of SiNPs-NH2, compared with the devices fabricated by original PEDOT:PSS.     

Influence of addition of lithium salt solution into PEDOT:PSS dispersion on the electrochemical and spectroscopic properties of film electrodes

The present work has studied electrochemical and optical properties of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) film electrodes drop-casted from commercial PEDOT:PSS aqueous dispersion with preliminary addition and without addition of LiClO₄ electrolyte (further denoted as PEDOT:PSS/LiClO₄ and PEDOT:PSS). Cyclic voltammetry measurements showed the significant increase in capacitance of PEDOT:PSS/LiClO₄ film electrodes in comparison to PEDOT:PSS. Furthermore, the improved charge transport in PEDOT:PSS/LiClO₄ films was demonstrated by electrochemical impedance spectra. In situ spectroelectrochemical measurements revealed that preliminary addition of LiClO₄ into PEDOT:PSS aqueous dispersion allows to increase amount of free charge carriers (polaron and bipolaron states) in the resulting film during electrochemical oxidation in LiClO₄ propylene carbonate solution. This increase was attributed to ion-induced charge screening between positively charged PEDOT and negatively charged PSS in polyelectrolyte structure, which was supported by structural investigations of both types of film electrodes by using FTIR, SEM, and XPS measurements. Charge screening results from a more open structure that allows conformational relaxation of PEDOT molecules during charge transport, which leads to partial separation of oppositely charged PSS and PEDOT molecules and facilitating the increase of electrochemical activity.

Open image in new window

Graphical abstract ?

     

EQCM study of redox properties of PEDOT/MnO<Subscript>2</Subscript> composite films in aqueous electrolytes

Electrochemical behavior of poly-3,4-ethylenedioxythiophene composites with manganese dioxide (PEDOT/MnO₂) has been investigated by cyclic voltammetry and electrochemical quartz crystal microbalance at various component ratios and in different electrolyte solutions. The electrochemical formation of PEDOT film on the electrode surface and PEDOT/MnO₂ composite film during the electrochemical deposition of manganese dioxide into the polymer matrix was gravimetrically monitored. The mass of manganese dioxide deposited into PEDOT at different time of electrodeposition and apparent molar mass values of species involved into mass transfer during redox cycling of PEDOT/MnO₂ composites were evaluated. It was found that during the redox cycling of PEDOT/MnO₂ composite films with various MnO₂ content, the oppositely directed fluxes of counterions (anions and cations) occur, resulting in a change of the slope of linear parts of the Δf–E plots with changing the mass fraction of MnO₂ in the composite film.Rectangular shape of cyclic voltammograms of PEDOT/MnO₂ composites with different loadings of manganese dioxide was observed, which is characteristic of the pseudocapacitive behavior of the composite material. Specific capacity values of PEDOT/MnO₂ composites obtained from cyclic voltammograms were about 169 F g^?1. The specific capacity, related to the contribution of manganese dioxide component, was about 240 F g^?1.     

Voltammetry of lead cations on a new type of silver composite electrode in the presence of other cations

A new type of silver composite electrode was examined, prepared from silver, graphite powder, and methacrylate resin. The effects of the presence of various cations (cadmium, copper, bismuth, thallium), anions (chlorides), surface-active substances (Triton X-100), and oxygen on the anodic-stripping voltammetric determination of lead were studied. It was found that the effect of underpotential deposition at the composite electrode differs from that produced at a metallic silver electrode, mainly at low concentrations of the deposited metal. The use of this type of silver composite electrode in differential pulse anodic-stripping voltammetry enables direct determination of lead in natural water samples without elimination of surface-active substances (LOD about 3 g L^–1).     

Radiation‐Induced Synthesis of Nanostructured Conjugated Polymers in Aqueous Solution: Fundamental Effect of Oxidizing Species

Synthesis of conjugated poly(3,4‐ethylenedioxythiophene) (PEDOT) polymers is achieved through the radiolysis of N₂O‐saturated aqueous solutions of 3,4‐ethylenedioxythiophene by using two different oxidizing species: HO^. (hydroxyl) and N₃^. (azide) radicals. Both oxidative species lead to self‐assembled polymers that are evidenced in solution by cryotransmission electron microscopy and UV/Vis absorption spectroscopy and, after centrifugation and deposition, by scanning electron microscopy and attenuated total reflectance FTIR techniques. Whereas HO^. radicals lead to PEDOT‐OH globular nanostructures with hydrophilic properties, N₃^. radicals enable the formation of amphiphilic PEDOT‐N₃ fibrillar nanostructures. These results, which highlight the differences in the intermolecular interaction behaviors of the two kinds of PEDOT polymers, are discussed in terms of polymerization mechanisms.