Piezoelectric transducer parameter selection for exciting a single mode from multiple modes of Lamb waves

Excitation and propagation of Lamb waves by using rectangular and circular piezoelectric transducers surface-bonded to an isotropic plate are investigated in this work. Analytical stain wave solutions are derived for the two transducer shapes, giving the responses of these transducers in Lamb wave fields. The analytical study is supported by a numerical simulation using the finite element method. Symmetric and antisymmetric components in the wave propagation responses are inspected in detail with respect to test parameters such as the transducer geometry, the length and the excitation frequency. By placing only one piezoelectric transducer on the top or the bottom surface of the plate and weakening the strength of one mode while enhancing the strength of the other modes to find the centre frequency, with which the peak wave amplitude ratio between the S0 and A0 modes is maximum, a single mode excitation from the multiple modes of the Lamb waves can be achieved approximately. Experimental data are presented to show the validity of the analyses. The results are used to optimize the Lamb wave detection system.     

Normal mode expansion method for laser-generated ultrasonic Lamb waves in orthotropic thin plates

A quantitative theory for modeling the laser-generated transient ultrasonic Lamb waves, which propagates along arbitrary directions in orthotropic plates, is presented by employing an expansion method of generalized Lamb wave modes. The displacement field is expressed by a summation of the symmetric and antisymmetric modes in the surface stress-free orthotropic plate, and therefore the theory is particularly appropriate for waveform analyses of Lamb waves in thin plates because one needs only to evaluate several lower modes. The transient waveforms excited by the thermoelastic expansion and the oil-coating evaporation are analyzed for a transversely isotropic thin plate. The results show that the theory provides a quantitative analysis to characterize anisotropic elastic stiffness properties of orthotropic plates by laser-generated Lamb wave detection.     

Lamb wave propagation in magnetoelectroelastic plates

Based on the three-dimensional linear elastic equations and magnetoelectroelastic constitutive relations, propagation of symmetric and antisymmetric Lamb waves in an infinite magnetoelectroelastic plate is investigated. The coupled differential equations of motion are solved, and the phase velocity equations of symmetric and antisymmetric modes are obtained for both electrically and magnetically open and shorted cases. The dispersive characteristic of wave propogation is explored. The mechanical, electric and magnetic responses of the lowest symmetric and antisymmetric Lamb wave modes are discussed in detailed. Obtained results are valuable for the analysis and design of broadband magnetoelectric transducer using composite materials.     

两侧有固体层负载时板中Lamb波的传播

本文研究了薄板二面有固体导负载时板中Ｌａｍｂ波的传播，从弹性波理论出发并结合应的边界条件，导出板中Ｌａｍｂ波的色散方程，数值计算表示，不管作为自由状态时板中Ｌａｍｂ波相速（板厚取定时）是大于或小于外层固体的声表面波波速，板中对称及反对称模式的Ｌａｍｂ波相速都随着外层固体层厚度增加而变化并且渐近于外层固体的声表面波波速，数值计算又表明，对很薄的板，板中对称及反对称模式的相速均随负载板的厚度呈线性变化     

Measurement of the scattering of a Lamb wave by a through hole in a plate

Flexural waves propagating in an aluminum plate containing a circular hole are studied. In the experiments the first antisymmetric Lamb wave mode A0 is excited selectively by a piezoelectric transducer. The scattered field around a circular cavity is measured pointwise using a heterodyne laser interferometer. The measurements are compared with theoretical calculations. Different approximate analytical approaches, employing Kirchhoff and Mindlin types of plate theories to describe the scattered field, are used. Good agreement between the experimental data and the analytical solutions is found within the ranges of validity of the different models. Introduction of a small imperfection, like a notch, at the boundary of the cavity changes the measured scattered field     

Absorption of zero Lamb waves in an elastic layer by mechanical resonators with friction

The propagation of zero Lamb waves in a plate with mechanical resonators attached to its surfaces is studied. It is shown that, in a plate that is single-mode for symmetric (antisymmetric) waves, the zero symmetric (antisymmetric) Lamb wave can be absorbed by mechanical resonators with a certain friction. The single-mode (for symmetric or antisymmetric waves) plate can be not thin compared to the wavelength of the transverse wave.     

Lamb wave radiation from plate termination in a liquid

The liquid wedge method is used to excite leaky Lamb waves on an aluminium plate while the plate is immersed in water. The excitation occurs near the end of the plate so that sonic energy of the excited mode radiates into the liquid. A Schlieren method is used to observe the radiation pattern and a correlation is made between the radiation lobe structure and the symmetric or antisymmetric nature of the excited mode. Theoretical calculations of the transfer of energy from the plate to the liquid are made and agreement between theory and experiment is obtained.     

采用单个压电传感器的单模式兰姆波激发频率的选择

考虑了压电传感器(PZT)与板之间的耦合作用,从理论上研究了单个压电传感器激发时产生单模式兰姆波的频率调节方法,实验给出了模式选择在兰姆波结构健康监测中的应用. 在板材、板厚以及PZT尺寸一定的情况下,从理论上能够预测到作为频率函数的各兰姆波模式的幅值变化. 根据某特定兰姆波模式的幅值最大而其他模式幅值相对最小时所对应的频率,即可识别出该兰姆波模式优化的激发频率. 数值仿真验证了理论的有效性以及单模式兰姆波选择的可能性. 在不同的激发频率下,分别激发了优化的A0 模式,优化的S0模式以及共存的A0和S0模 关键词： 兰姆波 压电传感器 激发频率 结构健康监测     

On the reflection of coupled Rayleigh-like waves at surface defects in plates

The reflection of coupled Rayleigh-like waves from surface defects in elastic plates is investigated experimentally and analyzed on the basis of an analytical model and finite difference simulations. The propagation of Rayleigh-like waves in plates is characterized by an energy transfer to the opposite plate side and back over a distance called the beat length. Experimental results clearly show this beating effect and its dependency on the frequency-thickness product, and excellent agreement is obtained with existing analytical predictions. The propagation and scattering are modeled separately for the fundamental A(0) and S(0) Lamb modes that constitute the incident Rayleigh-like wave. The reflection coefficients from surface slots are investigated using finite difference simulations and the reflected Rayleigh-like wave is obtained by superposition. The theoretical model reveals strong dependencies of the reflected field on the ratio between excitation distance and beat length and on the cutoff frequencies of specific higher Lamb modes. Standard pulse-echo measurements allow for the detection of small defects from a remote transducer location. Good agreement is obtained between the predicted and measured amplitude spectra of the reflected Rayleigh-like wave. The developed model allows for the evaluation of defect location and damaged plate side using a combination of time-of-flight and frequency measurements.     

An oscillator using high order Lamb wave modes

An oscillator using high order Lamb wave modes is presented. Due to the multimode property of Lamb waves, high frequency oscillators using high order mode Lamb waves can be fabricated. To select the operating mode of the Lamb wave oscillator, a high order mode selector is inserted into the feedback loop. An oscillator using the 13th antisymmetric mode (a₁₃) in Lamb wave is achieved in experiments and the oscillating frequency is 5.30 times higher than that of the a₀ mode excited by the interdigital transducer.     

Conventional electromagnetic acoustic transducer development for optimum Lamb wave modes

Lamb waves are normally utilized for inspecting thin metal sheets. Wheel type probes using piezoelectric oscillators have generally been used as the sensors for Lamb waves. Recently, the electromagnetic acoustic transducer (EMAT) has been developed and is beginning to be used as a Lamb wave detector. We have developed a useful type of transducer for Lamb waves. The new EMAT consists of a meander coil with a narrow distance of 2.5 mm and has a symmetrical structure in the vertical direction for both surface sides. The new EMAT can generate Lamb waves with variable wavelengths corresponding to the frequency range from approximately 300 kHz to 2.5 MHz and multiple modes, and can also generate selected symmetrical and anti-symmetrical mode Lamb waves. It is demonstrated that the optimum Lamb wave mode could be produced by the appropriate positioning of the EMATs and controlling the phase (same or inversed) of the electrical signal driving the device. The described EMAT can be used to examine steel (or other material) sheets of different thickness. It is also shown that the S0 (0.3 MHz) mode Lamb wave is the most effective for the deepest (up to 6 mm) penetration.     

Stresses of a Symmetric Lamb Wave in the Middle-Wavelength Range: Study of an Internal Wave

Acoustical Physics - The paper considers the stress-strain state of an elastic unbounded plate during propagation of the fundamental mode of a symmetric Lamb wave. Particular attention is paid to...     

Generalized thermoelastic Lamb waves in a plate bordered with layers of inviscid liquid

The propagation of thermoelastic waves in a homogeneous isotropic, thermally conducting plate bordered with layers of inviscid liquid or half-space of inviscid liquid on both sides is investigated in the context of generalized theories of thermoelasticity. Secular equations for the plate in closed form and isolated mathematical conditions for symmetric and antisymmetric wave modes in completely separate terms are derived. The results for coupled and uncoupled theories of thermoelasticity have been obtained as particular cases. The different regions of secular equations are obtained and special cases, such as Lame modes, thin plate waves and short wavelength waves of the secular equations are also discussed. The secular equations for thermoelastic leaky Lamb waves are also obtained and deduced. The amplitudes of displacement components and temperature change have also been computed and studied. Finally, the numerical solution is carried out for an aluminum-epoxy composite and aluminum materials plate bordered with water. The dispersion curves for symmetric and antisymmetric thermoelastic wave modes and amplitudes of displacement and temperature change in case of fundamental symmetric (S₀) and skew symmetric (A₀) modes are presented in order to illustrate and compare the theoretical results. The theory and numerical computations are found to be in close agreement. The results have been deduced and compared with the relevant publications available in the literature at the relevant stages of the work.     

PVDF梳状换能器接收非线性兰姆波的实验研究*

该文基于PVDF压电薄膜对梳状换能器进行设计制作,并将该换能器应用于接收非线性兰姆波信号实验研究。首先通过输出矢量和方法分析PVDF梳状换能器的工作特性,然后将设计制作的PVDF梳状换能器应用于铝板中非线性兰姆波信号的接收,并与传统压电陶瓷换能器经斜劈接收的非线性兰姆波信号进行比较分析。实验结果表明,两种换能器所接收到的信号幅值随传播距离的变化趋势相近,线性增长的积累效应表征结果相似,且PVDF梳状换能器可以对基波和二次谐波信号同时响应。除此之外,PVDF梳状换能器用于接收非线性兰姆波信号更加稳定。因此,PVDF梳状换能器有望应用于复杂构件的在线检测与监测研究。     

Elastic constants of a plate from impact-echo resonance and Rayleigh wave velocity

A new method is proposed for calculating the dynamic elastic constants of an isotropic plate from measurements of the impact-echo resonance and Rayleigh wave velocity. Poisson's ratio is shown to be a single-valued function of the ratio between thickness frequency and Rayleigh wave velocity. This dependence is derived theoretically from the condition of resonance at the minimum frequency of the first-order symmetric Lamb mode. A finite element model is developed to determine how this frequency varies with Poisson's ratio. The results obtained by modal analysis and the power-spectral density technique are in good agreement with those calculated as the solution of the S1 Lamb mode equation. The method is verified by impact-echo tests on concrete and methacrylate plates. A laser interferometer is used to detect the vibration. Thickness frequencies are accurately identified by applying the multicross-spectral density to the signals detected at several points close to the impact point. In a separate experiment, Rayleigh waves are generated by the mediator technique. The wave velocities are determined from the arrival times of the surface wave at several points. Finally, the main sources of uncertainty are evaluated.     

Laser-ultrasonic generation of Lamb waves in the reaction force range

The Laser-ultrasonic generation of Lamb waves in an elastic plate is investigated theoretically and experimentally for a laser source whose intensity is high enough to create reaction forces (normal tractions) on the illuminated surface of the specimen. The analytical solutions for transient waves are derived using the integral transform method first by considering an arbitrary source shape and time excitation function, and then specifically for circular and line source shapes. The simulation study allows us not only to predict the behavior of individual wave modes but also to construct the overall responses; thus it helps us better understand the wave excitation mechanisms. The dispersive and multi-modal nature of laser-generated Lamb waves is presented by showing the spatiotemporal Fourier transform of displacements obtained by the simulation study. The transform, displayed in the frequency-wave number domain, enunciates the characteristics of the propagating individual Lamb wave modes. The simulation results are then compared with the 2-D Fourier transform of a set of experimental data obtained by scanning an aluminum plate specimen.     

Maxima and minima of the displacement components for the Lamb modes

This paper revisits the vanishing of the transverse component of the particle displacement vector in free surfaces of an isotropic homogeneous plate, for both symmetric and antisymmetric Lamb waves. Drawing on well-known analytical expressions from Viktorov's book [(1967) Rayleigh and Lamb Waves: Physical Theory Applications, Chap. II, pp. 67-121], two distinct frequency-thickness product expressions, in cases where this vanishing occurs, are derived: one for the symmetric modes and another for the antisymmetric modes. At these frequency-thickness products, phase and group velocities have appreciable values which are discussed herein. It appears that these velocities depend on the transverse bulk wave velocity only. This is the specific condition of the Lame? modes. Moreover, theoretical and experimental investigations of displacements in the surface of a plate in air have been carried out. The theoretical part shows that the normal and transverse displacements have, respectively, a local maximum and a local minimum in the vicinity of these frequency-thickness products. The experimental part corroborates the presence of the local maximum of the S(0) Lamb mode for various materials.     

Lamb waves beam deviation due to small inclination of the test structure in air-coupled ultrasonic NDT

In Lamb waves inspection, an air-coupled transmitter transducer is oriented at a specific angle such that it generates a pure Lamb mode which propagates along the structure and interacts with any existing defects. For this inspection system, amplitude losses appears when small inclinations of the tested structure occurs. An important factor which affects directly these losses has been observed, it consists of the Lamb waves beam (LWB) deviation due to this bad alignment. In this work, a simple expression of LWB deviation has been deduced. This expression includes the test structure angle, phase velocity of generated Lamb mode, and the phase velocity of waves propagating in the coupled medium. A(0) Lamb mode is generated and detected in 1 mm thick aluminium plate sample using 1 MHz PZ27 piezoelectric transducers of 20 mm of diameter. Experimental LWB deviation angles are measured for different inclination angles of the test sample. A comparative study is released with theoretical results. For 1 degree of misalignment in the aluminium plate inclination, and transducers separation distance of 35 mm, LWB deviation angle is around 7 degrees and the amplitude is reduced by around 11%. Then, for a large separation distance, we must move the receiver transducer to detect the deviated LWB. It is shown that, for both theoretical and experimental studies, the LWB deviation and its measured amplitude are very sensitive to the alignment of the tested structure with respect to the transmitter-receiver transducers plane. In metal plates it is most satisfactory to use A(0) mode compared with S(0) mode since it is easy to excite and has a large amplitude and small deviation beam angles.     

Design of optimal configuration for generating A0 Lamb mode in a composite plate using piezoceramic transducers

This work concerned a technique for a health monitoring system based on the generation and sensing of Lamb waves in composite structures by thin surface-bonded piezoceramic transducers. The objective was to develop transducers that are adapted for the damage detection in orthotropic composites. The key problem with the investigated Lamb waves was to select a mode to be sensitive to the damage. A hybrid modeling technique was therefore used to conceive transducers that were adapted to achieve such a feature. This modeling technique enabled studying the influence of the transducer characteristics on the Lamb waves propagating in orthotropic plates. It was demonstrated that a Lamb mode could be generated dominantly to other modes by using a multi-element transducer. The effectiveness of this technique was successfully verified experimentally on composite plates. It was shown that the dominant Lamb mode, obtained by use of dual-element transducers, was an appropriate mode for successfully detecting a damage in composites.     

Acoustic waves propagating in a fluid-filled spherical shell placed in a liquid

Acoustic waves arising in a fluid-filled elastic spherical shell placed in a liquid are considered. It is demonstrated that, in general, none of the four types of waves possible in such a system (subsonic and supersonic antisymmetric Lamb waves, symmetric Lamb waves, and whispering galleries) is realized separately, but an interaction between the waves of different types takes place.