Viscoelasticity and thermal stability of polylactide composites with various functionalized carbon nanotubes

Polylactide (PLA) nanocomposites containing various functionalized multi-walled carbon nanotubes (MWCNTs) were prepared directly by melt compounding. The linear rheology and thermal stability of the PLA nanocomposites were, respectively, investigated by the parallel plate rheometer and TGA, aiming at examining the effect of surface functionalization on the dispersion of MWCNTs by using viscoelastic and thermal properties. Among three MWCNTs used in this work, the carboxylic MWCNTs present better dispersion in PLA matrix than the hydroxy and purified MWCNTs because the corresponding composite shows the lowest rheological percolation threshold, which is further confirmed by the TEM and solution experiments. The presence of all these three MWCNTs, however, nearly cannot improve the thermal stability effectively at the initial stage of degradation and the temperature corresponding to a weight loss of 5 wt% (T_5 wt%) only shows slight increase in contrast to that of the neat PLA while with increase of decomposition level, the presence of carboxylic and purified MWCNTs retards the depolymerization of PLA evidently, showing remarkable increase in the temperature corresponding to maximum rate of decomposition (T_max). Both the dispersion state and the surface functionalization of MWCNTs are very important to the thermal stability of PLA matrix.     

Multi walled carbon nanotubes induced viscoelastic response of polypropylene copolymer nanocomposites: Effect of filler loading on rheological percolation

Polypropylene random copolymer nanocomposites having 0.2–7.0 vol% multi-walled carbon nanotubes (MWCNTs) were prepared via melt processing. Transmission electron microscopy (TEM) was employed to determine the nano scale dispersion of carbon nanotubes. Linear viscoelastic behavior of these nanocomposites was investigated using parallel plate rheometry. Incorporation of carbon nanotubes in the polymer matrix resulted in higher complex viscosity (η*), storage (G′) and loss modulus (G″) as compared to neat polymer, especially in the low-frequency region, suggesting a change from liquid to solid-like behavior in the nanocomposites. By plotting storage modulus vs. carbon nanotube loading and fitting with a power law function, the rheological percolation threshold in these nanocomposites was observed at a loading of ∼0.27 vol% of MWCNTs. However, electrical percolation threshold was reported at ∼0.19 vol% of MWCNTs loading. The difference in the percolation thresholds is understood in terms of nanotube connectivity with nanotubes and polymer chain required for electrical conductivity and rheological percolation.     

Isotactic polypropylene/carbon nanotube composites prepared by latex technology: Electrical conductivity study

Several series of nanocomposites were prepared using a latex-based process, the main step of which consisted of mixing an aqueous suspension of exfoliated carbon nanotubes (CNTs) and a polymer latex. In the present work, a systematic study on the electrical properties of fully amorphous (polystyrene - PS) as well as semi-crystalline (isotactic polypropylene - iPP) nanocomposites containing either single-wall (SWCNTs) or multi-wall carbon nanotubes (MWCNTs) has been conducted. Percolation thresholds as low as 0.05 wt.% or 0.1 wt.% were observed for SWCNT/iPP and MWCNT/iPP nanocomposites, respectively. The formation of a conductive percolating network at such a low CNT concentration is favored by the high intrinsic conductivity and the low viscosity of the polymer matrix. The electrical percolation threshold of the iPP-based system was found to be lower than its rheological percolation threshold. Beyond the percolation threshold, MWCNT-based nanocomposites generally exhibited higher conductivity levels than those based on SWCNTs, most probably due to the higher intrinsic conductivity of the MWCNTs as compared to that of the SWCNTs. These excellent electrical properties, associated with the strong nucleating effect of the CNTs reported earlier [1] and [2], render this type of nanocomposites extremely attractive from a technological point of view.     

Electro-responsive transdermal drug delivery behavior of PVA/PAA/MWCNT nanofibers

The electro-responsive transdermal drug delivery system was prepared by electrospinning of poly(vinyl alcohol)/poly(acrylic acid)/multi-walled carbon nanotubes (MWCNTs) nanocomposites. The surface modification of MWCNTs was carried out by oxyfluorination to introduce the functional groups on the hydrophobic MWCNTs. The dispersion of MWCNTs and the compatibility with polymer matrices were improved by oxyfluorination. The MWCNT content and oxyfluorination condition played important roles in the swelling and drug release characteristics of nanofibers. The conductivity of nanofibers increased by increasing the content of MWCNTs and performing oxyfluorination with higher oxygen content. Uniform distribution of the oxyfluorinated MWCNTs in the nanofibers was crucial to the electro-responsive swelling and drug releasing behaviors of nanofibers.     

Dissolution of MWCNTs by using polyoxadiazoles,and highly effective reinforcement of their composite films

Nonmodified multiwalled carbon nanotubes (MWCNTs)/sulfonated polyoxadiazole (sPOD) nanocomposites are successfully prepared by a facile solution route. The pristine MWCNTs are dispersed in a sPOD solution, and the mixtures are fabricated into thin films by solution casting. The homogeneous dispersion of nanotubes in the composites is confirmed by transmission electron microscopy. The mechanical properties, thermal stability, and electrical conductivity are investigated. Tensile strength, elongation at break, and tensile energy to break are shown to increase by more than 28, 45, and 73%, respectively, by incorporating up to 1.0 wt % pristine MWCNTs. The experimental values for sPOD/MWCNTs composite stiffness are compared with Halpin‐Tsai and modified Halpin‐Tsai predictions. The storage modulus is found to increase up to 10% at low CNT loading. The composite films, which have an outstanding thermal stability, show an increase of up to 57 °C in the initial degradation temperature. The addition of 1.0 wt % MWCNTs increases the electrical conductivity of the sPOD matrix by two orders of magnitude. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Properties of matrix-grafted multi-walled carbon nanotube/poly(methyl methacrylate) nanocomposites synthesized by in situ reversible addition-fragmentation chain transfer polymerization

Multi-walled carbon nanotubes (MWCNT)/poly(methyl methacrylate) (PMMA) nanocomposites were synthesized by the in situ reversible addition-fragmentation chain transfer (RAFT) polymerization of methyl methacrylate (MMA) in the presence of MWCNTs, at which the bulk polymer was grafted onto the surface of nanotubes through the ??grafting through?? strategy. For this purpose, MWCNTs were formerly functionalized with polymerizable MMA groups. MMA and PMMA-grafted MWCNTs were characterized by Fourier-transform infrared spectroscopy, Raman, X-ray photoelectron spectroscopy, transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Dissolution of nanotubes was examined in chloroform solvent and studied by UV?Cvis spectroscopy. Thermogravimetric and degradation behavior of prepared nanocomposites was investigated by TGA. MWCNTs had a noticeable boosting effect on the thermal stability of nanocomposites. TGA thermograms showed a two-step weight loss pattern for the degradation of MWCNT-PMMA/PMMA nanocomposites which is contrast with neat PMMA. Introduction of MWCNTs also improved the dynamic mechanical behavior and electrical conductivity of nanocomposites. TEM micrograph of nanocomposite revealed that the applied methods for functionalization of nanotubes and in situ synthesis of nanocomposites were comparatively successful in dispersing the MWCNTs in PMMA matrix.     

Effect of oxidation treatment of multi-walled carbon nanotubes on the adsorption of pentachlorophenol from aqueous solution: Kinetics study

Multi-walled carbon nanotubes (MWCNTs) were oxidized using different oxidizing agents and the produced oxidized MWCNTs were characterized using different techniques. IR measurements showed the presence of carboxylic acid function groups especially for the MWCNTs oxidized with nitric acid and hydrogen peroxide. The adsorption of pentachlorophenol (PCP) to pristine and oxidized multi-walled carbon nanotubes (MWCNTs) has been studied. The results showed that the oxidation of the MWCNTs decreased their abilities to adsorb PCP compared with the pristine MWCNTs. The adsorption was studied kinetically and the results showed that the adsorption process occurs in two different steps. The first step involves the transfer of PCP to the surface of the oxidized MWCNTs, which was very fast due to the diffusion of PCP from the liquid phase to the solid phase. This step followed by a second slower step of adsorption could be due to intra-particle diffusion.     

Compatibilisation effect of PP-g-MA copolymer on iPP/SiO2 nanocomposites prepared by melt mixing

In the present study, a series of iPP/SiO₂ nanocomposites, containing 1, 2.5, 5, 7.5, 10 and 15 wt% SiO₂ nanoparticles, were prepared by melt mixing in a twin screw co-rotating extruder. Poly(propylene-g-maleic anhydride) copolymer (PP-g-MA) containing 0.6 wt% maleic anhydride content was added to all nanocomposites at three different concentrations, 1, 2.5 and 5 wt%, based on silica content. Mechanical properties such as tensile strength at break and Young’s modulus were found to increase and to be mainly affected by the content of silica nanoparticles as well as by the copolymer content. For the tensile strength at break as well as for yield point, a maximum was observed, corresponding to the samples containing 2.5-5 wt% SiO₂. At higher concentrations, large nanosilica agglomerates are formed that have as a result a decrease in tensile strength. Young’s modulus increases almost linearly on the addition of SiO₂, and takes values up to 60% higher than that of neat iPP. Higher concentrations of PP-g-MA resulted in a further enhancement of mechanical properties due to silica agglomerate reduction. This finding was verified from SEM and TEM micrographs. Evidently the surface silica hydroxyl groups of SiO₂ nanoparticles react with maleic anhydride groups of PP-g-MA and lead to a finer dispersion of individual SiO₂ nanoparticles in the iPP matrix. The enhanced adhesion in the interface of the two materials, as a result of the mentioned reaction, has been studied and proved by using several equations. The increased Vicat point of all nanocomposites, by increasing the PP-g-MA content, can also be mentioned as a positive effect.     

Structure-property relationships in polyamide 12/halloysite nanotube nanocomposites

Polyamide 12 (PA12) nanocomposites based on halloysite nanotubes (HNTs) were obtained using a batch internal mixer or a twin-screw mini-compounder. In order to analyze the influence of HNTs dispersion on nanocomposite properties, morphological analysis (SEM and TEM) was combined with rheological and thermo-mechanical experiments. The linear viscoelastic properties and the dynamic storage modulus were expectedly found to increase with increasing HNT loading. Higher enhancements were observed for PA12/HNTs nanocomposites obtained by twin-screw mini-compounding. This finding was related to the better degree of dispersion and alignment of the silicate nanotubes throughout the matrix. Thermal stability was also improved by the halloysite nanotubes presumably by an entrapment mechanism of the volatile products inside the hollow tubular structure. DSC measurements further highlighted a nucleation effect of HNTs on the nanocomposites. In view of these results, halloysite nanotubes are promising candidates in the field of PA nanocomposites for structural applications.     

Thermal degradation kinetics of in situ prepared PET nanocomposites with acid-treated multi-walled carbon nanotubes

A series of PET/acid-treated multi-walled carbon nanotubes (MWCNTs) nanocomposites of varying nanoparticles’ concentration were prepared, using the in situ polymerization technique. TEM micrographs verified that the dispersion of the MWCNTs into the PET matrix was homogeneous, while some relatively small aggregates co-existed at higher filler contents. Intrinsic viscosity of the prepared nanocomposites was increased at low MWCNTs contents (up to 0.25 wt%), while at higher contents a gradual reduction was observed. The surface carboxylic groups of acid-treated MWCNTs probably reacted with the hydroxyl end groups of PET, acting as chain extenders at smaller concentrations, while at higher concentrations, on the other hand, led to the formation of branched and cross-linked macromolecules, with reduced apparent molecular weights. From the thermogravimetric curves, it was concluded that the prepared samples exhibited good thermostability, since no remarkable mass loss occurred up to 320 °C (<0.5%). The activation energy (E) of degradation of the studied materials was estimated using the Ozawa, Flynn, and Wall (OFW), Friedman and Kissinger’s methods. Pure PET had an E = 223.5 kJ/mol, while in the PET/MWCNTs nanocomposites containing up to 1 wt% the E gradually increased, indicating that MWCNTs had a stabilizing effect upon the decomposition of the matrix. Only the sample containing 2 wt% of MWCNTs exhibited a lower E due to the existence of the aforementioned cross-linked macromolecules. The form of the conversion function for all the studied samples obtained by fitting was the mechanism of nth-order auto-catalysis.     

Melt‐crystallization mechanism of poly(ethylene terephthalate)/multi‐walled carbon nanotubes prepared by in situ polymerization

A series of poly(ethylene terephthalate)/multi‐walled carbon nanotubes (PET/MWCNTs) nanocomposites were prepared by in situ polymerization using different amounts of multi‐walled carbon nanotubes (MWCNTs). The polymerization of poly(ethylene terephthalate) (PET) was carried out by the two‐stage melt polycondensation method. The intrinsic viscosity (IV) of the composites is ranged between 0.31 and 0.63 dL/g depending on the concentration of the MWCNTs. A decrease of IV was found by increasing MWCNTs content. This is due to the reactions taking place between the two components leading to branched and crosslinked macromolecules. These reactions are, mainly, responsible for thermal behavior of nanocomposites. The melting point of the nanocomposites was shifted to slightly higher temperatures by the addition till 0.55 wt % of MWCNTs while for higher concentration was reduced. The degree of crystallinity in all nanocomposites was, also, reduced by increasing MWCNTs amount. However, from crystallization temperature, it was found that MWCNTs till 1 wt % can enhance the crystallization rate of PET, whereas at higher content (2 wt %), the trend is the opposite due to the formation of crosslinked macromolecules. From the extended crystallization analysis, it was proved that MWCNTs act as nucleating agents for PET crystallization. Additionally, the crystallization mechanism due to the existence of MWCNT becomes more complicated because two mechanisms with different activation energies are taking place in the different degrees of crystallization, depending on the percentage of MWCNT. The effect of molecular weight also plays an important role. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1452–1466, 2009     

Gold nanocatalysts supported on protonic titanate nanotubes and titania nanocrystals

Gold nanoparticles were first supported on protonic titanate nanotubes with the formation of Au/titanate nanocomposites. They were further transformed to Au/titania nanocomposites via an acetic acid treatment at 70 °C for 60 h. The porosity, crystal structure and morphology of those composites have been studied by X-ray diffraction (XRD), High-resolution transmission electron microscope (HRTEM), and low-temperature nitrogen adsorption. Catalytic tests for CO oxidation show that the Au/titanate nanocomposites had a promising activity with complete conversion of CO at 70 °C and that of Au/titania was at room temperature (25 °C). Both catalysts exhibited good thermal and long-term stabilities. The influence of the crystal vacancies and surface properties of the titanate and titania supports on the catalytic activities were evaluated.     

Heterogeneous ion-exchange membranes based on sulfonated poly(1,4-phenylene sulfide) and linear polyethylene: preparation, oxidation stability, methanol permeability and electrochemical properties

Poly(1,4-phenylene sulfide) was sulfonated with chlorosulfonic acid in 1,2-dichloroethane. The product (IEC = 2.38 mequiv./g) was ground and sieved (mesh size 63 μm) to obtain small particles. The particles and linear polyethylene were mixed in various ratios and the resulting blends were press-molded at 150 °C to obtain the membranes. Membranes containing up to 66 wt.% of sulfonated particles could be prepared without any problem in mechanical strength. The membranes were characterized by their stability in oxidative environment, ionic conductivity, and diffusive permeability to methanol. The membrane containing 66 wt.% of sulfonated particles was almost as conductive as Nafion 117; it exhibited, however, much lower diffusive permeability to methanol. In a strongly oxidative environment (3% aqueous H₂O₂ at 70 °C), the prepared membranes were less stable than Nafion 117, but much more stable than membranes with sulfonated poly(styrene-co-divinylbenzene) particles. In preliminary laboratory tests with H₂/O₂ and direct methanol fuel cells, the prepared membranes with high concentrations of sulfonated particles performed similarly to Nafion 117.     

Strengthening of liquid crystalline polymer by functionalized carbon nanotubes through interfacial interaction and homogeneous dispersion

Multiwalled carbon nanotubes (MWCNTs) were functionalized with two types of chemical moieties (i.e. carboxylic, ? COOH and hydroxyl benzoic acid groups, ‐HBA) on their sidewalls in order to improve their interaction with a liquid crystalline polymer (LCP) and dispersion in LCP. We have investigated the rheological, mechanical, dynamic mechanical, and thermal properties in detail with variation of HBA‐functionalized MWCNTs in the LCP matrix. Effect of the dispersion state of the functionalized MWCNTs in the LCP matrix on the rheological behavior was also studied. The composites containing HBA‐functionalized MWCNTs showed higher complex viscosity, storage, and loss modulus than the composites with the same loading of raw MWCNTs and MWCNT‐COOH. It was suggested that the HBA‐functionalized MWCNTs exhibited a better dispersion in the polymer matrix and formed stronger CNT‐polymer interaction in the composites than the raw MWCNTs and MWCNT‐COOH, which was also confirmed by FESEM and FTIR studies. As a result, the overall mechanical performance of the HBA‐MWCNT‐LCP composites could be improved significantly. For example, the addition of 4 wt% HBA‐MWCNT to LCP resulted in the considerable improvements in the tensile strength and modulus of LCP (by 66 and 90%, respectively). Copyright © 2010 John Wiley & Sons, Ltd.     

Calorimetric study on oxidation of alumina supported rhodium by dioxygen

Rhodium particles in nanometer size were prepared by impregnating alumina powders with aqueous solutions containing rhodium salts. The dispersion (D) of rhodium crystallites on the prepared samples was estimated by dioxygen adsorption measured at 300 K. Phenomena of oxidizing the supported crystallites with 2.5 × 10⁴ Pa O₂ in a temperature range between 280 and 870 K were calorimetrically studied. Extent of oxidation may be distinguished into three stages, i.e., adsorption on surface (T < 300 K), progressive penetration into bulk, and formation of a stable bulk oxide (T> 700 K), on raising the oxidation temperature. Heat of dioxygen adsorption varies only slightly with the dispersion (D) of rhodium and has a value of 294 ± 6 kJ (mol O₂)⁻¹. Chemical stoichiometry of the bulk oxide formed, however, varies with the dispersion of rhodium crystallites. A dioxide (RhO₂) (_f H = 225 ± 3 kJ (mol O₂)⁻¹) and a sesquioxide (Rh₂O₃) (_f H = 273 ± 3 kJ (mol O₂)⁻¹) was formed at D < 60% and D> 80%,     

Influence of inorganic fullerene‐like WS2 nanoparticles on the thermal behavior of isotactic polypropylene

A new family of thermoplastic nanocomposites based on isotactic polypropylene (iPP) and inorganic fullerene‐like tungsten disulfide (IF‐WS₂) has been successfully prepared. A very efficient dispersion of IF‐WS₂ material was obtained by mixing in the melted polymer without using modifiers or surfactants. The addition of IF‐WS₂ nanoparticles induces a remarkable enhancement of the thermal stability of iPP, as well as an increase in the crystallization rate of the matrix when compared with pure iPP. The nucleating efficiency of IF‐WS₂ solid lubricant nanoparticles on the α‐phase of iPP reaches very high values (60–70%), the highest values observed hitherto for polypropylene nanocomposites. The incorporation of IF‐WS₂ has also been observed to increase the size and stability of the crystals formed. The melting behavior of the nanocomposites indicates the formation of more perfect crystals as determined by differential scanning calorimetry and time‐resolved synchrotron X‐ray scattering experiments. The new nanocomposites show an increase in the storage modulus with respect to pure iPP measured by dynamic mechanical analysis. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2309–2321, 2007     

New oxo-bridged dinuclear peroxotungsten(VI) complexes: Synthesis, stability and activity in bromoperoxidation

Two new dinuclear oxo-bridged peroxo complexes of tungsten with coordinated dipeptides of the type, Na₂[W₂O₃(O₂)₄(glycyl-glycine)₂] · 3H₂O (1) and Na₂[W₂O₃(O₂)₄(glycyl-leucine)₂] · 3H₂O (2) have been synthesized from the reaction of H₂WO₄, 30% H₂O₂ and the respective dipeptide at pH ca. 2.5. Synthesis of the compounds, in addition to pH, is sensitive to reaction temperature and concentrations of the components. The compounds were characterized by elemental analysis, spectral and physico-chemical methods including thermal analysis. In the dimeric complexes the two W(VI) centres with edge bound peroxo groups are bridged by an oxo group. The dipeptides occurring as zwitterions bind the metal centers through O (carboxylate) atoms leading to hepta co-ordination around each W(VI). Thermal stability of the compounds as well as their stability in solution were determined. The compounds are highly stable toward decomposition in solutions of acidic as well as physiological pH. These compounds, besides another similar dimeric compound Na₂[W₂O₃(O₂)₄(cystine)] · 4H₂O (3) efficiently oxidized bromide to a bromination competent intermediate in phosphate buffer at physiological pH, a reaction in which only two of the peroxide groups of the complex species were found to be active. The complexes could also mediate bromination of organic substrate in aqueous-organic media.     

Influence of MWCNT morphology on dispersion and thermal properties of polyethylene nanocomposites

In this study a series of multi-walled carbon nanotube (MWCNT)/Polyethylene (PE) composites with different kinds and several concentrations of carbon nanotubes (CNTs) were investigated. The morphology and degree of dispersion of the fillers in the polymer matrix at different length scales was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Both individual and agglomerated MWCNTs were evident but a good dispersion was observed for some of them. TGA measurements were performed on nanocomposites in order to understand if CNTs affect the stabilization mechanism during thermal and oxidative degradation. The analysis demonstrates that MWCNTs presence slightly delays thermal volatilisation (15-20 °C) without modification of thermal degradation mechanism. In contrast, thermal oxidative degradation in air is delayed up to about 100 °C dependently from MWCNTs concentration, in the range used here (0.1-2.0 wt%), and degree of dispersion. The stabilization is due to the formation of a thin protective layer of entangled MWCNTs kept together by carbon char generated on the surface of the nanocomposites as shown by SEM images taken on degradation residues.     

Thermogravimetric, differential scanning calorimetric and experimental thermal transport study of MWCNT/NBR nanocomposites

Pristine multiwalled carbon nanotubes (MWCNTs) were impregnated in acrylonitrile butadiene rubber (NBR) using internal dispersion kneader and two roller mixing mill to investigate the effects of various nanotubes concentrations on the thermal transport/stability of rubber nanocomposites. Thermal conductivity (λ _N) and thermal impedance (R) measurement experimental setups were established according to ASTM E1225-99 and D5470-03. The 1 mass % addition of MWCNTs in the polymer matrix has enhanced R up to 44 % and reduced λ _N of the rubber nanocomposite up to 40 % compare to the base composite formulation. Thermal decomposition and differential thermal analyses of the fabricated composite specimens simulate that the thermal stability and endothermic capability are augmented with increasing the nanotubes contents in the host matrix. The progressive incorporations of carbon nanotubes into the rubber matrix have efficiently influenced the composite specimens regarding glass transition, crystallization, and melting temperatures including their specific enthalpies. Scanning electron microscopy along with the energy dispersive spectroscopy was used to analyze MWCNTs dispersion in NBR matrix, compositional analysis of the nanocomposite, and impregnated nanotubes.     

Crystallization and morphology of iPP/MWCNT prepared by compounding iPP melt with MWCNT aqueous suspension

In this work, isotactic polypropylene (iPP) composites filled with multiwalled carbon nanotubes (MWCNTs) were prepared by compounding iPP melt with MWCNT aqueous suspension using a corotating twin-screw extruder, and the morphology and crystallization behavior of the composites were investigated. Scanning electron microscopy micrographs showed that MWCNTs dispersed individually at nanoscale in the iPP matrix when the MWCNTs concentration was low, though MWCNTs aggregates were detected when the filler concentration increased. The results of differential scanning calorimetry, wide-angle X-ray diffraction, and polarized light microscopy indicated that the β-form crystal of iPP was induced by MWCNTs at the concentration of 0.1 wt.% which was dispersed individually in the iPP matrix. At higher content, however, MWCNTs acted as α-nucleating agent, and the crystals in the iPP/MWCNT composites showed higher degree of perfection than that of pure iPP though smaller in dimension. Crystallization rate of iPP increased significantly with increasing MWCNT content.