2,2,2‐trifluoroacetophenone‐based D‐π‐A type photoinitiators for radical and cationic photopolymerizations under near‐UV and visible LEDs

Two D‐π‐A‐type 2,2,2‐trifluoroacetophenone derivatives, namely, 4′‐(4‐( N,N‐diphenyl)amino‐phenyl)‐phenyl‐2,2,2‐trifluoroacetophenone (PI‐Ben) and 4′‐(4‐(7‐(N,N‐diphenylamino)‐9,9‐dimethyl‐9H‐fluoren‐2‐yl)‐phenyl‐2,2,2‐trifluoroacetophenone (PI‐Flu), are developed as high‐performance photoinitiators combined with an amine or an iodonium salt for both the free‐radical polymerization of acrylates and the cationic polymerization of epoxides and vinyl ether upon exposure to near‐UV and visible light‐emitting diodes (LEDs; e.g., 365, 385, 405, and 450 nm). The photochemical mechanisms are investigated by UV‐Vis spectra, molecular‐orbital calculations, fluorescence, cyclic voltammetry, photolysis, and electron‐spin‐resonance spin‐trapping techniques. Compared with 2,2,2‐trifluoroacetophenone, both photoinitiators exhibit larger redshift of the absorption spectra and higher molar‐extinction coefficients. PI‐Ben and PI‐Flu themselves can produce free radicals to initiate the polymerization of acrylate without any added hydrogen donor. These novel D‐π‐A type trifluoroacetophenone‐based photoinitiating systems exhibit good efficiencies (acrylate conversion = 48%–66%; epoxide conversion = 85%–95%; LEDs at 365–450 nm exposure) even in low‐concentration initiators (0.5%, w/w) and very low curing light intensities (1–2 mW cm^?2). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1945–1954     

Photoinduced and thermally induced cationic polymerizations using S,S‐dialkyl‐S‐(3,5‐dimethylhydroxyphenyl)sulfonium salts

A study of the photoinitiated and thermally initiated cationic polymerizations of several monomer systems with S,S‐dialkyl‐S‐(3,5‐dimethylhydroxyphenyl)sulfonium salt (HPS) photoinitiators bearing different lengths of alkyl chains on the positively charged sulfur atom has been conducted. HPS photoinitiators are capable of photoinitiating the cationic polymerization of a wide variety of epoxy and vinyl ether monomers directly on irradiation with short‐wavelength UV light. Aryl ketone photosensitizers are effective in extending the spectral response of these photoinitiators into the long‐wavelength UV region. Kinetic studies with real‐time infrared spectroscopy show that HPS photoinitiators exhibit good efficiency in the polymerization of epoxide and vinyl ether monomers. Comparative studies also demonstrate that S,S‐dimethyl‐S‐(3,5‐dimethyl‐2‐hydroxyphenyl)sulfonium salts are more active photoinitiators than their isomeric S,S‐dimethyl‐S‐(3,5‐dimethyl‐4‐hydroxyphenyl)sulfonium salt counterparts. Both types of HPS photoinitiators display reversible photolysis as a result of facile termination reactions that take place between the growing chains ends with the photogenerated sulfur ylides. Preliminary studies have shown that HPS photoinitiators can also be employed as thermal initiators for the cationic ring‐opening polymerization of epoxides at moderate temperatures. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2570–2587, 2003     

Initiator effect on the cationic ring‐opening copolymerization of 2‐ethyl‐2‐oxazoline and 2‐phenyl‐2‐oxazoline

The aim of this research was to study the effect of the initiator on the resulting monomer distribution for the cationic ring‐opening copolymerization of 2‐ethyl‐2‐oxazoline (EtOx) and 2‐phenyl‐2‐oxazoline (PhOx). At first, kinetic studies were performed for the homopolymerizations of both monomers at 160 °C under microwave irradiation using four initiators. These initiators have the same benzyl‐initiating group but different leaving groups, Cl^?, Br^?, I^?, and OTs^?. The basicity of the leaving group affects the ratio of covalent and cationic propagating species and, thus, the polymerization rate. The observed differences in polymerization rates could be correlated to the concentration of cationic species in the polymerization mixture as determined by ¹H NMR spectroscopy. In a next‐step, polymerization kinetics were determined for the copolymerizations of EtOx and PhOx with these four initiators. The reactivity ratios for these copolymerizations were calculated from the polymerization rates obtained for the copolymerizations. This approach allows more accurate determination of the copolymerization parameters compared to conventional methods using the composition of single polymers. When benzyl chloride (BCl) was used as an initiator, no copolymers could be obtained because its reactivity is too low for the polymerization of PhOx. With decreasing basicity of the used counterions (Br^? > I^? > OTs^?), the reactivity ratios gradually changed from r_EtOx = 10.1 and r_PhOx = 0.30 to r_EtOx = 7.9 and r_PhOx = 0.18. However, the large difference in reactivity ratios will lead to the formation of quasi‐diblock copolymers in all cases. In conclusion, the used initiator does influence the monomer distribution in the copolymers, but for the investigated system the differences were so small that no difference in the resulting polymer properties is expected. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4804–4816, 2008     

Cationic polymerization of isobutyl vinyl ether initiated with transition‐metal ate complexes

The cationic polymerization of isobutyl vinyl ether was examined with transition‐metal ate complexes with trityl cation as initiators. The initiators were generated by the reaction of triphenylmethyl chloride [trityl chloride (TrCl)] with ate complexes of Nb, Mo, and W with lithium cation, which were obtained in situ by the reaction of the transition‐metal halides with anionic reagents (organolithium or lithium amide). When the polymerization was initiated with a mixture of TrCl and Li⁺[NbH₅(NnBuPh)]^?, the resulting poly(isobutyl vinyl ether)s had narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight = 1.13–1.20). Although the polymerization was supposed to be initiated by the electrophilic attack of the trityl cation, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis of the resulting poly(isobutyl vinyl ether)s revealed the presence of H at the α‐chain end. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2636–2641, 2006     

The ligand effect in Ti‐mediated living radical styrene polymerizations initiated by epoxide radical ring opening. 1. Alkoxide and bisketonate Ti complexes

Bisketonate and alkoxide Ti(III) complexes derived from Zn reduction of Ti(IV) precursors were evaluated as catalysts for the living radical polymerization (LRP) of styrene initiated by Ti‐catalyzed epoxide radical ring opening and mediated by reversible termination with Ti(III). No polymerization occurred with tris(2,2,6, 6‐tetramethyl‐3,5‐heptanedionato)titanium (III), whereas dichlorobis(2,2,6,6‐tetramethyl‐3,5‐heptanedionato)titanium (IV) affords only a free radical polymerization. Preliminary living features were displayed by (ⁱPrO)₂TiCl₂. Investigations of the effect of epoxide/Ti/Zn ratios, temperature, and nature of the epoxide demonstrated that (ⁱPrO)₃TiCl provides a linear dependence of M_n on conversion over a wide range of conditions with an optimum for [Sty]/[epoxide group]/[Ti]/[Zn] = 50/1/2/4 at 90 °C. However, the polydispersity could not be reduced below 1.4–1.5, with an initiator efficiency of 0.15. These results were rationalized in terms of a combination of decreased Ti oxophilicity and ligand exchange. The lowered oxophilicity decreases the initiation rate and broadens M_w/M_n. The fast alkoxide exchange promotes a weak dependence of the polymerization on reaction conditions and generates macromolecular Ti species with reduced ability to mediate LRP. Thus, while monofunctional epoxides provide homogeneous polymerizations and narrower M_w/M_n, difunctional initiators may lead to gel formation at high conversion. Nonetheless, all polymerizations were light gray to colorless and afforded white polymer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6028–6038, 2005     

Evaluation of initiator systems for controlled and sequentially curable free‐radical/cationic hybrid photopolymerizations

Free‐radical/cationic hybrid photopolymerizations of acrylates and epoxides were initiated using a three‐component initiator system comprised of camphorquinone as the photosensitizer, an amine as the electron donor, and a diaryliodonium salt. Thermodynamic considerations revealed that the oxidation potential of the electron donor must be less than 1.34 V relative to SCE for electron transfer with the photoexcited camphorquinone to take place. This electron transfer leads to the production of the active centers for the hybrid polymerization (two radicals and a cation). Further investigation revealed that only a subset of electron donors that meet the oxidation potential requirement resulted in polymerization of the epoxide monomer; therefore, a second requirement for the electron donor (pK_b higher than 8) was established. Experiments performed using a combination of electron donors revealed that the onset of the hybrid system's cationic polymerization can be advanced or delayed by controlling the concentration and composition of the electron donor(s). These studies demonstrate that a single three‐component initiator system can be used to initiate and chemically control the sequential curing properties of a free‐radical/cationic hybrid photopolymerization and is a viable alternative to separate photoinitiators for each type of polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1747–1756, 2005     

Radical polymerization of 1‐alkenes catalyzed by lithium salts of carboranes

Radical polymerization of selected 1‐alkenes, (1‐hexene, 1‐octene and 2‐methyl‐1‐heptene), initiated with classical radical initiators and catalyzed by lithium salts of selected carboranes was studied. In accordance with recently published results it was found that the use of radical initiators under catalysis by “naked” lithium cation of carboranes promotes the radical polymerization of 1‐alkenes, otherwise nonpolymerizable by the radical mechanism. However, although in our experiments relatively high monomers conversions are reached for some of the thermal initiators used, only low‐molecular‐weight oligomers with M_n < 1000 are formed, regardless of the initiator and carborane anion used. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synergistic interaction of epoxides and N‐vinylcarbazole during photoinitiated cationic polymerization

A kinetic study was conducted of the independent photoinitiated cationic polymerization of a number of epoxide monomers and mixtures of these monomers with N‐vinylcarbazole. The results show that these two different classes of monomers undergo complex synergistic interactions with one another during polymerization. It was demonstrated that N‐vinylcarbazole as well as other carbazoles are efficient photosensitizers for the photolysis of both diaryliodonium and triarylsulfonium salt photoinitiators. In the presence of large amounts of N‐vinylcarbazole, the rates of the cationic ring‐opening photopolymerization of epoxides are markedly accelerated. This effect has been ascribed to a photoinitiated free‐radical chain reaction that results in the oxidation of monomeric and polymeric N‐vinylcarbazole radicals by the onium salt photoinitiators to generate cations. These cations can initiate the ring‐opening polymerization of the epoxides, leading to the production of copolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3697–3709, 2000     

Copper and iron complexes as visible‐light‐sensitive photoinitiators of polymerization

The utilization of visible lights for the fabrication of polymeric materials is recognized as a promising and environmentally friendly approach. This process relies on the photochemical generation of reactive species (e.g., radicals, radical cations, or cations) from well‐designed photoinitiators (PIs) or photoinitiating systems (PISs) to initiate the polymerization reactions of different monomers (acrylates, methacrylates, epoxides, and vinyl ethers). In spite of the fact that metal complexes such as ruthenium‐ or iridium‐based complexes have found applications in organic and polymer synthesis, the search of other low‐cost metal‐based complexes as PISs is emerging and attracting increasing attentions. Particularly, the concept of the photoredox catalysis has appeared recently as a unique tool for polymer synthesis upon soft conditions (use of light emitting diodes and household lamp). This highlight focuses on recently designed copper and iron complexes as PI catalysts in the application of photoinduced polymerizations (radical, cationic, interpenetrated polymer networks, and thiol‐ene) or controlled radical polymerization under visible light irradiation. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2673–2684     

Kinetic studies on the imine base/isocyanate‐induced radical polymerization of vinyl monomers

Specific imine bases (IB) in conjunction with various isocyanates (IC) mediate the radical polymerization of radically polymerizable monomers such as methyl methacrylate (MMA). Advantageously, the 2‐(methylmercapto)‐2‐thiazoline MMT/IC combination as initiator works even at room temperature for polymerization of MMA. The coefficients a, b, and c of the basic rate law of monomer consumption d[M]/dt = k_p·[IC]^a·[IB]^b·[M]^c were determined. The order a has been determined to 0.5 showing the root law of radical polymerization with respect to the IC component as initiator. Moreover, b and c amount 1. The initiator combination MMT/ IC was applied to determine the influence of the molecular structure of the IC on the rate of monomer conversion. For aromatic isocyantes, the gross rate constant of monomer consumption correlates with the Hammet constant of aromatic substituents. The activation energies of the gross polymerization rate constant of several initiator mixtures were determined whereby the value of E_A,Br was found to be between typical values of radical polymerization initiated by photochemical reactions (～20 kJ/mol) and commonly used thermal decomposing initiators (～80 kJ/mol). Presumptions on the initiating and terminating step of the IB/IC mediated polymerization were done by means of electrospray ionization mass spectrometry, NMR spectroscopy, and the elemental composition of the head and end group of the resulting polymers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of star polymers via nitroxide mediated free‐radical polymerization: A “core‐first” approach using resorcinarene‐based alkoxyamine initiators

The synthesis of new octafunctional alkoxyamine initiators for nitroxide‐mediated radical polymerization (NMRP), by the derivatization of resorcinarene with nitroxide free radicals viz TEMPO and a freshly prepared phosphonylated nitroxide, is described. The efficiency of these initiators toward the controlled radical polymerization of styrene and tert‐butyl acrylate is investigated in detail. Linear analogues of these multifunctional initiators were also prepared to compare and evaluate their initiation efficiency. The favorable conditions for polymerization were optimized by varying the concentration of initiators and free nitroxides, reaction conditions, etc., to obtain well‐defined star polymers. Star polystyrene thus obtained were further used as macro‐initiator for the block copolymerization with tert‐butyl acrylate. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5559–5572, 2007     

Redox initiated cationic polymerization: Silane‐N‐aryl heteroaromatic onium salt redox couples

In this article, a new route for the synthesis of N‐aryl heteroaromatic onium salts by the direct copper catalyzed arylation of pyridine, substituted pyridines, isoquinoline, and acridine with diaryliodonium salts is described. It was demonstrated that these N‐aryl heteroaromatic onium salts undergo facile platinum or rhodium‐catalyzed reduction by silanes bearing Si? H groups. The reduction of N‐aryl heteroaromatic onium salts generates Brønsted acids. When this redox reaction was carried out in situ in the presence of an appropriate monomer, cationic polymerization was observed. Using this approach, the cationic polymerizations of epoxides, oxetanes, 1,3,5‐trioxane, styrene, and vinyl ethers were carried out. The use of optical pyrometry to monitor the redox initiated cationic polymerizations of some representative multifunctional monomers is described. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

An experimental study on the kinetics and mechanisms of styrene polymerization in oil‐in‐water microemulsion initiated by oil‐soluble initiators

In order to clarify the kinetic role of oil‐soluble initiators in microemulsion polymerization, the oil‐in‐water (O/W) microemulsion polymerizations of styrene are carried out using four kinds of azo‐type oil‐soluble initiators with widely different water‐solubility. The results are compared with those observed when a water‐soluble initiator, potassium persulfate (KPS) is used. For all the oil‐soluble initiators used, the molecular weight of polymers and the average size of polymer particles do not change with the monomer conversion and the initial initiator concentration. The monomer conversion is expressed as a function of r_i^0.5t, where r_i is the rate of radical generation in the whole reaction system and t is the reaction time. These characteristics are quite the same as those observed when KPS is used as an initiator. When the polymerizations are carried out with the rate of radical generation in the whole reaction system fixed at the same value, the rates of polymerization are almost the same for all the oil‐soluble initiators employed, irrespective of their water‐solubility, but are significantly lower (ca. 1/3) than that with KPS. Then, the following conclusions are given: (1) The radicals generated not only in the aqueous phase, but also in the micelle and polymer particle phase are almost equally effective for the polymerization. However, (2) only a small portion (ca. 1/9) of the radicals generated in both phases participate in the polymerization. (3) Bimolecular termination of a growing radical in the polymer particle with an entering radical and with a pair of radicals generated in the polymer particles is negligible, and hence, the molecular weight of polymers is determined only by chain transfer to monomer.     

Dual roles for promoting monomers to polymers: A conjugated sulfonium salt photoacid generator as photoinitiator and photosensitizer in cationic photopolymerization

An efficient strategy for comprehensive utilization of the conjugated sulfonium salt photoacid generator (PAG), namely, 3‐{4‐[4‐(4‐N,N′‐diphenylamino)‐styryl]phenyl}phenyl dimethyl sulfonium hexafluoroantimonate, was developed through photoinitiated cationic photopolymerization (CP) of epoxides and vinyl ether upon exposure to near‐UV and visible light‐emitting diodes (LEDs; e.g., 365, 385, 405, and 425 nm). Photochemical mechanisms were investigated by UV–vis spectra, molecular orbital calculations, fluorescence, cyclic voltammetry, and electron spin resonance spin‐trapping analyses. Compared with commercial PAGs, the prepared conjugated sulfonium salt generated H⁺, which can be used as photoinitiator. Moreover, the fluorescent byproducts from photodecomposition can be used as photosensitizer of commercial iodonium salt in the photoinitiating systems of CP. These novel D‐π‐A type sulfonium‐based photoinitiating systems are efficient (epoxide conversion = 85–90% and vinyl conversion >90%; LEDs upon exposure to 365–425 nm) even in low‐concentration initiators (1%, w/w) and low curing light intensities (10–40 mW cm^?2). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2722–2730     

D‐π‐a‐type oxime sulfonate photoacid generators for cationic polymerization under UV–visible LED irradiation

Four D‐π‐A‐type nonionic oxime sulfonate photoacid generators (PAGs) have been designed and synthesized for use in light‐emitting diode (LED) excitable cationic photoinitiators, in which N,N‐diphenylamino was used as electron donor with trifluoroacetophenone‐based oxime sulfonates (trifluoromethanoesulfonate and p‐toluenesulfonate) as electron acceptor and substituted fluorene and biphenyl groups as the π‐conjugated systems. PAG‐Ben‐Tol (with biphenyl and p‐toluenesulfonate) and PAG‐Flu‐Tol (with fluorene and p‐toluenesulfonate) showed high quantum yields of photoacid generation (0.33–0.50) and very good thermal stability (over 250 °C). The absorbance spectra of these PAGs were consistent with the emission spectra of commercially gained UV–visible LED light sources. The potential of these PAGs for cationic photoinitiators was tested in two cationic monomer systems. These PAGs needed low light intensity and low concentration for photopolymerization with high conversions of monomer, for example, over 80%, gained at 3.0 mW cm⁻² from 365 to 470 nm LEDs. The photochemical mechanisms of these PAGs are comprehensively investigated and discussed in detail. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1146–1154     

Visible‐light‐sensitive photoredox catalysis by iron complexes: Applications in cationic and radical polymerization reactions

The development of iron complexes for the photoredox catalysis is a huge challenge. Indeed, Iron complexes can be ideal candidates due to their potential visible light absorption and redox properties but also because they are less toxic, inexpensive and environmentally friendly compared to other catalysts. In the present paper, a series of novel iron complexes have been synthesized and utilized to initiate the free radical promoted cationic polymerization of epoxides or the free radical polymerization of acrylates through photoredox catalysis processes upon exposure to near UV (385 nm) or visible violet (405 nm) light emitting diodes (LEDs). When combined with an iodonium salt and N‐vinylcarbazole, the iron complex‐based photoinitiating systems are able to generate radicals, cations, and radical cations. The initiation efficiency is investigated through real‐time Fourier transform infrared spectroscopy and a satisfactory initiating ability is found. The mechanisms for the generation of the reactive initiating species through photoredox catalysis are studied by different methods (steady state photolysis, cyclic voltammetry and electron spin resonance spin trapping techniques) and discussed in detail. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2247–2253     

Synthesis of comb‐branched polyacrylamide with cationic poly[(2‐dimethylamino)ethyl methacrylate dimethylsulfate] quat

Comb‐branched polyelectrolytes with polyacrylamide backbones and poly[(2‐dimethylamino)ethyl methacrylate methylsulfate] (polyDMAEMA‐DMS) side chains were prepared by free‐radical macromonomer polymerization. PolyDMAEMA‐DMS macromonomers bearing terminal styrenic moieties were synthesized by living anionic polymerization with lithium 4‐vinylbenzylamide (LiVBA) and lithium N‐isopropyl‐4‐vinylbenzylamide (LiPVBA) as initiators. In the presence of LiCl, LiPVBA initiated a living polymerization of 2‐(dimethylamino)ethyl methacrylate (DMAEMA) and produced polymers with well‐controlled molecular weights and low polydispersities. LiVBA could not directly initiate DMAEMA polymerization. After being capped with two units of dimethylacrylamide, DMAEMA polymerized with an initiator efficiency of 63%. The quaternization of the poly[(2‐dimethylamino)ethyl methacrylate] macromonomer with dimethyl sulfate yielded the cationic polyDMAEMA‐DMS macromonomer. The polyDMAEMA‐DMS macromonomer had a much higher reactivity than acrylamide in free‐radical polymerization. This might have been due to the formation of polyDMAEMA‐DMS micelles in the polymerization system. The high macromonomer reactivity caused composition drift in a batch process. A semibatch method with a constant polyDMAEMA‐DMS feed rate was used to control the copolymer composition. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2394–2405, 2002     

Naphthalimide‐phthalimide derivative based photoinitiating systems for polymerization reactions under blue lights

Naphthalimide‐phthalimide derivatives (NDPDs) have been synthesized and combined with an iodonium salt, N‐vinylcarbazole, amine or 2,4,6‐tris(trichloromethyl)‐1,3,5‐triazine to produce reactive species (i.e., radicals and cations). These generated reactive species are capable of initiating the cationic polymerization of epoxides and/or the radical polymerization of acrylates upon exposure to very soft polychromatic visible lights or blue lights. Compared with the well‐known camphorquinone based systems used as references, the novel NDPD based combinations employed here demonstrate clearly higher efficiencies for the cationic polymerization of epoxides under air as well as the radical polymerization of acrylates. Remarkably, one of the NDPDs (i.e., NDPD2) based systems is characterized by an outstanding reactivity. The structure/reactivity/efficiency relationships of the investigated NDPDs were studied by fluorescence, cyclic voltammetry, laser flash photolysis, electron spin resonance spin trapping, and steady state photolysis techniques. The key parameters for their reactivity are provided. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 665–674     

Synthesis of novel tetrahydrofuran‐epichlorohydrin [poly(THF‐b‐ECH)] macromonomeric peroxy initiators by cationic copolymerization and the quantum chemically investigation of initiation system effects

Cationic polymerization of tetrahydrofuran (THF) and epichlorohydrin (ECH) was performed with peroxy initiators synthesized from bis (4,4′‐bromomethyl benzoyl peroxide (BBP) or bromomethyl benzoyl t‐butyl peroxy ester (t‐BuBP) and AgSbF₆ or ZnCl₂ system at 0 °C to obtain the poly(THF‐b‐ECH) macromonomeric peroxy initiators. Kinetic studies were accomplished for poly(THF‐b‐ECH) initiators. Poly(THF‐b‐ECH‐b‐MMA) and poly(THF‐b‐ECH‐b‐S) block copolymers were synthesized by bulk polymerization of methyl methacrylate (MMA) and styrene (S) with poly(THF‐b‐ECH) initiators. The quantum chemical calculations for the block copolymers, the initiating systems of the cationic polymerization of THF and ECH were achieved using HYPERCHEM 7.5 program. The optimized geometries of the polymers were investigated with the quantum chemical calculations. Poly(THF‐b‐ECH) initiators having peroxygen groups were used for graft copolymerization of polybutadien (PBd) to obtain poly(THF‐b‐ECH‐g‐PBd) crosslinked graft copolymers. The graft copolymers were investigated by sol‐gel analysis. Swelling ratio values of the graft copolymers in CHCl₃ were calculated. The characterizations of the polymers were achieved by FTIR, ¹H NMR, GPC, SEM, TEM, and DSC techniques. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2896–2909, 2010     

Kinetic study of free‐radical polymerization photoinitiated by cyanine‐borate salts. II.

A series of cyanine butyltriphenylborate salts were prepared and tested as initiators of free‐radical polymerization photoinitiated via a photoinduced electron‐transfer process. For the majority of the tested series, the highest rate of photoinitiated free‐radical polymerization was observed when sec‐butyl radicals were formed. Essentially, there was no influence of the quantum yield of the free‐radical formation on the rate of the free‐radical polymerization initiated by the cyanine‐borate salts. The experimental data revealed that the relationship between the rate of polymerization and the free energy change for the electron transfer displayed typical Marcus region kinetic behavior. The photoreduction of the cyanine butyltriphenylborate salts produced colorless products. The efficiency of the bleached‐dye formation had no effect on the overall efficiency of photoinitiated polymerization. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2365–2374, 2000