Solvent Molecule Cooperation Enhancing Lithium Metal Battery Performance at Both Electrodes

Developing electrolytes compatible with efficient and reversible cycling of electrodes is critical to the success of rechargeable Li metal batteries (LMBs). The Coulombic efficiencies and cycle lives of LMBs with ethylene carbonate (EC), dimethyl carbonate, ethylene sulfite (ES), and their combinations as electrolyte solvents show that in a binary‐solvent electrolyte the extent of electrolyte decomposition on the electrode surface is dependent on the solvent component that dominates the solvation sheath of Li⁺. This knowledge led to the development of an EC‐ES electrolyte exhibiting high performance for Li||LiFePO₄ batteries. Carbonate molecules occupy the solvation sheath and improve the Coulombic efficiencies of both the anode and cathode. Sulfite molecules lead to desirable morphology and composition of the solid electrolyte interphase and extend the cycle life of the Li metal anode. The cooperation between these components provides a new example of electrolyte optimization for improved LMBs.     

Revealing an Interconnected Interfacial Layer in Solid‐State Polymer Sodium Batteries

Replacing the commonly used nonaqueous liquid electrolytes in rechargeable sodium batteries with polymer solid electrolytes is expected to provide new opportunities to develop safer batteries with higher energy densities. However, this poses challenges related to the interface between the Na‐metal anode and polymer electrolytes. Driven by systematically investigating the interface properties, an improved interface is established between a composite Na/C metal anode and electrolyte. The observed chemical bonding between carbon matrix of anode with solid polymer electrolyte, prevents delamination, and leads to more homogeneous plating and stripping, which reduces/suppresses dendrite formation. Full solid‐state polymer Na‐metal batteries, using a high mass loaded Na₃V₂(PO₄)₃ cathode, exhibit ultrahigh capacity retention of more than 92 % after 2 000 cycles and over 80 % after 5 000 cycles, as well as the outstanding rate capability.     

Deep‐Eutectic‐Solvent‐Based Self‐Healing Polymer Electrolyte for Safe and Long‐Life Lithium‐Metal Batteries

The deployment of high‐energy‐density lithium‐metal batteries has been greatly impeded by Li dendrite growth and safety concerns originating from flammable liquid electrolytes. Herein, we report a stable quasi‐solid‐state Li metal battery with a deep eutectic solvent (DES)‐based self‐healing polymer (DSP) electrolyte. This electrolyte was fabricated in a facile manner by in situ copolymerization of 2‐(3‐(6‐methyl‐4‐oxo‐1,4‐dihydropyrimidin‐2‐yl)ureido)ethyl methacrylate (UPyMA) and pentaerythritol tetraacrylate (PETEA) monomers in a DES‐based electrolyte containing fluoroethylene carbonate (FEC) as an additive. The well‐designed DSP electrolyte simultaneously possesses non‐flammability, high ionic conductivity and electrochemical stability, and dendrite‐free Li plating. When applied in Li metal batteries with a LiMn₂O₄ cathode, the DSP electrolyte effectively suppressed manganese dissolution from the cathode and enabled high‐capacity and a long lifespan at room and elevated temperatures.     

A Perovskite Electrolyte That Is Stable in Moist Air for Lithium‐Ion Batteries

Solid‐oxide Li⁺ electrolytes of a rechargeable cell are generally sensitive to moisture in the air as H⁺ exchanges for the mobile Li⁺ of the electrolyte and forms insulating surface phases at the electrolyte interfaces and in the grain boundaries of a polycrystalline membrane. These surface phases dominate the total interfacial resistance of a conventional rechargeable cell with a solid–electrolyte separator. We report a new perovskite Li⁺ solid electrolyte, Li_0.38Sr_0.44Ta_0.7Hf_0.3O_2.95F_0.05, with a lithium‐ion conductivity of σ_Li=4.8×10^?4 S cm^?1 at 25 °C that does not react with water having 3≤pH≤14. The solid electrolyte with a thin Li⁺‐conducting polymer on its surface to prevent reduction of Ta⁵⁺ is wet by metallic lithium and provides low‐impedance dendrite‐free plating/stripping of a lithium anode. It is also stable upon contact with a composite polymer cathode. With this solid electrolyte, we demonstrate excellent cycling performance of an all‐solid‐state Li/LiFePO₄ cell, a Li‐S cell with a polymer‐gel cathode, and a supercapacitor.     

Enabling High‐Voltage Lithium Metal Batteries by Manipulating Solvation Structure in Ester Electrolyte

Lithium metal is an ideal electrode material for future rechargeable lithium metal batteries. However, the widespread deployment of metallic lithium anode is significantly hindered by its dendritic growth and low Coulombic efficiency, especially in ester solvents. Herein, by rationally manipulating the electrolyte solvation structure with a high donor number solvent, enhancement of the solubility of lithium nitrate in an ester‐based electrolyte is successfully demonstrated, which enables high‐voltage lithium metal batteries. Remarkably, the electrolyte with a high concentration of LiNO₃ additive presents an excellent Coulombic efficiency up to 98.8 % during stable galvanostatic lithium plating/stripping cycles. A full‐cell lithium metal battery with a lithium nickel manganese cobalt oxide cathode exhibits a stable cycling performance showing limited capacity decay. This approach provides an effective electrolyte manipulation strategy to develop high‐voltage lithium metal batteries.     

Studies on the effects of coated Li2CO3 on lithium electrode

Although a lithium metal anode has a high energy density compared with a carbon insertion anode, the poor rechargeability prevents the practical use of anode materials. A lithium electrode coated with Li₂CO₃ was prepared as a negative electrode to enhance cycleability through the control of the solid electrolyte interface (SEI) layer formation in Li secondary batteries. The electrochemical characteristics of the SEI layer were examined using chronopotentiometry (CP) and impedance spectroscopy. The Li₂CO₃-SEI layer prevents electrolyte decomposition reaction and has low interface resistance. In addition, the lithium ion diffusion in the SEI layer of the uncoated and the Li₂CO₃-coated electrode was evaluated using chronoamperometry (CA).     

Cycling a Lithium Metal Anode at 90 °C in a Liquid Electrolyte

Stable operation at elevated temperature is necessary for lithium metal anode. However, Li metal anode generally has poor performance and safety concerns at high temperature (>55 °C) owing to the thermal instability of the electrolyte and solid electrolyte interphase in a routine liquid electrolyte. Herein a Li metal anode working at an elevated temperature (90 °C) is demonstrated in a thermotolerant electrolyte. In a Li|LiFePO₄ battery working at 90 °C, the anode undergoes 100 cycles compared with 10 cycles in a practical carbonate electrolyte. During the formation of the solid electrolyte interphase, independent and incomplete decomposition of Li salts and solvents aggravate. Some unstable intermediates emerge at 90 °C, degenerating the uniformity of Li deposition. This work not only demonstrates a working Li metal anode at 90 °C, but also provides fundamental understanding of solid electrolyte interphase and Li deposition at elevated temperature for rechargeable batteries.     

Formulation of Blended‐Lithium‐Salt Electrolytes for Lithium Batteries

Blended‐salt electrolytes showing synergistic effects have been formulated by simply mixing several lithium salts in an electrolyte. In the burgeoning field of next‐generation lithium batteries, blended‐salt electrolytes have enabled great progress to be made. In this Review, the development of such blended‐salt electrolytes is examined in detail. The reasons for formulating blended‐salt electrolytes for lithium batteries include improvement of thermal stability (safety), inhibition of aluminum‐foil corrosion of the cathode current collector, enhancement of performance over a wide temperature range (or at a high or low temperature), formation of favorable interfacial layers on both electrodes, protection of the lithium metal anode, and attainment of high ionic conductivity. Herein, we highlight key scientific issues related to the formulation of blended‐salt electrolytes for lithium batteries.     

Lithium Azide as an Electrolyte Additive for All‐Solid‐State Lithium–Sulfur Batteries

Of the various beyond‐lithium‐ion battery technologies, lithium–sulfur (Li–S) batteries have an appealing theoretical energy density and are being intensely investigated as next‐generation rechargeable lithium‐metal batteries. However, the stability of the lithium‐metal (Li°) anode is among the most urgent challenges that need to be addressed to ensure the long‐term stability of Li–S batteries. Herein, we report lithium azide (LiN₃) as a novel electrolyte additive for all‐solid‐state Li–S batteries (ASSLSBs). It results in the formation of a thin, compact and highly conductive passivation layer on the Li° anode, thereby avoiding dendrite formation, and polysulfide shuttling. It greatly enhances the cycling performance, Coulombic and energy efficiencies of ASSLSBs, outperforming the state‐of‐the‐art additive lithium nitrate (LiNO₃).     

High‐Throughput Production of Zr‐Doped Li4Ti5O12 Modified by Mesoporous Libaf3 Nanoparticles for Superior Lithium and Potassium Storage

Li₄Ti₅O₁₂ is a promising anode for lithium‐ion batteries due to its zero‐strain properties. However, its low conductivity has greatly affected its rate performance. At the same time, the electrolyte decomposition during cycling also needs to be solved, especially at low cut‐off voltage. Herein, using a high‐throughput two‐step method, we synthesized Zr‐doped LTO modified by mesoporous LiBaF₃ nanoparticles for alkali‐ion storage. The doping of Zr can enhance the electronic conductivity and facilitate the rate performance. Meanwhile, the coating of mesoporous LiBaF₃ nanoparticles can form a mesoporous surface with large pore size (ca. 3–10 nm), which can benefit the alkali ion diffusion and simultaneously restrain the formation of an excess solid electrolyte interface to a reasonable range. The optimized material is used as an advanced anode for both lithium‐ion and potassium‐ion batteries, and good battery behavior including high‐rate performance and high stability is achieved.     

A Sustainable Solid Electrolyte Interphase for High‐Energy‐Density Lithium Metal Batteries Under Practical Conditions

High‐energy‐density Li metal batteries suffer from a short lifespan under practical conditions, such as limited lithium, high loading cathode, and lean electrolytes, owing to the absence of appropriate solid electrolyte interphase (SEI). Herein, a sustainable SEI was designed rationally by combining fluorinated co‐solvents with sustained‐release additives for practical challenges. The intrinsic uniformity of SEI and the constant supplements of building blocks of SEI jointly afford to sustainable SEI. Specific spatial distributions and abundant heterogeneous grain boundaries of LiF, LiN_xO_y, and Li₂O effectively regulate uniformity of Li deposition. In a Li metal battery with an ultrathin Li anode (33 μm), a high‐loading LiNi_0.5Co_0.2Mn_0.3O₂ cathode (4.4 mAh cm^?2), and lean electrolytes (6.1 g Ah^?1), 83 % of initial capacity retains after 150 cycles. A pouch cell (3.5 Ah) demonstrated a specific energy of 340 Wh kg^?1 for 60 cycles with lean electrolytes (2.3 g Ah^?1).     

Integrated lithium metal anode protected by composite solid electrolyte film enables stable quasi-solid-state lithium metal batteries

Lithium (Li) metal, possessing an extremely high theoretical specific capacity (3860 mAh/g) and the most negative electrode potential (−3.040 V vs. standard hydrogen electrode), is one the most favorable anode materials for future high-energy-density batteries. However, the poor cyclability and safety issues induced by extremely unstable interfaces of traditional liquid Li metal batteries have limited their practical applications. Herein, a quasi-solid battery is constructed to offer superior interfacial stability as well as excellent interfacial contact by the incorporation of Li@composite solid electrolyte integrated electrode and a limited amount of liquid electrolyte (7.5 μL/cm²). By combining the inorganic garnet Al-doped Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZO) with high mechanical strength and ionic conductivity and the organic ethylene-vinyl acetate copolymer (EVA) with good flexibility, the composite solid electrolyte film could provide sufficient ion channels, sustained interfacial contact and good mechanical stability at the anode side, which significantly alleviates the thermodynamic corrosion and safety problems induced by liquid electrolytes. This innovative and facile quasi-solid strategy is aimed to promote the intrinsic safety and stability of working Li metal anode, shedding light on the development of next-generation high-performance Li metal batteries.     

Solvation Structure with Enhanced Anionic Coordination for Stable Anodes in Lithium-Oxygen Batteries

Li-O₂ batteries have garnered much attention due to their high theoretical energy density. However, the irreversible lithium plating/stripping on the anode limits their performance, which has been paid little attention. Herein, a solvation-regulated strategy for stable lithium anodes in tetraethylene glycol dimethyl ether (G4) based electrolyte is attempted in Li-O₂ batteries. Trifluoroacetate anions (TFA⁻) with strong Li⁺ affinity are incorporated into the lithium bis(fluorosulfonyl)imide (LiTFSI)/G4 electrolyte to attenuate the Li⁺-G4 interaction and form anion-dominant solvates. The bisalt electrolyte with 0.5 M LiTFA and 0.5 M LiTFSI mitigates G4 decomposition and induces an inorganic-rich solid electrolyte interphase (SEI). This contributes to decreased desolvation energy barrier from 58.20 to 46.31 kJ mol⁻¹, compared with 1.0 M LiTFSI/G4, for facile interfacial Li⁺ diffusion and high efficiency. It yields extended lifespan of 120 cycles in Li-O₂ battery with a limited Li anode (7 mAh cm⁻²). This work gains comprehensive insights into rational electrolyte design for Li-O₂ batteries.     

A Liquid/Liquid Electrolyte Interface that Inhibits Corrosion and Dendrite Growth of Lithium in Lithium‐Metal Batteries

A proof‐of‐concept study on a liquid/liquid (L/L) two‐phase electrolyte interface is reported by using the polarity difference of solvent for the protection of Li‐metal anode with long‐term operation over 2000 h. The L/L electrolyte interface constructed by non‐polar fluorosilicane (PFTOS) and conventionally polar dimethyl sulfoxide solvents can block direct contact between conventional electrolyte and Li anode, and consequently their side reactions can be significantly eliminated. Moreover, the homogeneous Li‐ion flow and Li‐mass deposition can be realized by the formation of a thin and uniform solid‐electrolyte interphase (SEI) composed of LiF, Li_xC, Li_xSiO_y between PFTOS and Li anode, as well as the super‐wettability state of PFTOS to Li anode, resulting in the suppression of Li dendrite formation. The cycling stability in a lithium–oxygen battery as a model is improved 4 times with the L/L electrolyte interface.     

Enabling ultrafast lithium-ion conductivity of Li2ZrCl6 by indium doping

Solid-state batteries with high energy density and safety are promising next-generation battery systems. However, lithium oxide and lithium sulfide electrolytes suffer low ionic conductivity and poor electrochemical stability, respectively. Lithium halide solid electrolyte shows high conductivity and good compatibility with the pristine high-voltage cathode but limited applications due to the high price of rare metal. Zr-based lithium halides with low cost and high stability possess great potential. Herein, a small amount of In³⁺ is introduced in Li₂ZrCl₆ to synthesize Li_2.25Zr_0.75In_0.25Cl₆ electrolytes with a high room temperature Li-ion conductivity of 1.08 mS/cm. Solid-state batteries using Li_2.25Zr_0.75In_0.25Cl₆/Li_5.5PS_4.5Cl_1.5 bilayer solid electrolytes combined with Li-In anode and pristine LiNi_0.7Mn_0.2Co_0.1O₂ cathode deliver high initial discharge capacities under different cut-off voltages. This work provides an effective strategy for enhancing the conductivity of Li₂ZrCl₆ electrolytes, promoting their applications in solid-state batteries.     

Highly Stable Lithium Metal Batteries Enabled by Regulating the Solvation of Lithium Ions in Nonaqueous Electrolytes

Safe and rechargeable lithium metal batteries have been difficult to achieve because of the formation of lithium dendrites. Herein an emerging electrolyte based on a simple solvation strategy is proposed for highly stable lithium metal anodes in both coin and pouch cells. Fluoroethylene carbonate (FEC) and lithium nitrate (LiNO₃) were concurrently introduced into an electrolyte, thus altering the solvation sheath of lithium ions, and forming a uniform solid electrolyte interphase (SEI), with an abundance of LiF and LiN_xO_y on a working lithium metal anode with dendrite‐free lithium deposition. Ultrahigh Coulombic efficiency (99.96 %) and long lifespans (1000 cycles) were achieved when the FEC/LiNO₃ electrolyte was applied in working batteries. The solvation chemistry of electrolyte was further explored by molecular dynamics simulations and first‐principles calculations. This work provides insight into understanding the critical role of the solvation of lithium ions in forming the SEI and delivering an effective route to optimize electrolytes for safe lithium metal batteries.     

Tailored Organic Electrode Material Compatible with Sulfide Electrolyte for Stable All‐Solid‐State Sodium Batteries

All‐solid‐state sodium batteries (ASSSBs) with nonflammable electrolytes and ubiquitous sodium resource are a promising solution to the safety and cost concerns for lithium‐ion batteries. However, the intrinsic mismatch between low anodic decomposition potential of superionic sulfide electrolytes and high operating potentials of sodium‐ion cathodes leads to a volatile cathode–electrolyte interface and undesirable cell performance. Here we report a high‐capacity organic cathode, Na₄C₆O₆, that is chemically and electrochemically compatible with sulfide electrolytes. A bulk‐type ASSSB shows high specific capacity (184 mAh g^?1) and one of the highest specific energies (395 Wh kg^?1) among intercalation compound‐based ASSSBs. The capacity retentions of 76 % after 100 cycles at 0.1 C and 70 % after 400 cycles at 0.2 C represent the record stability for ASSSBs. Additionally, Na₄C₆O₆ functions as a capable anode material, enabling a symmetric all‐organic ASSSB with Na₄C₆O₆ as both cathode and anode materials.     

Transient Behavior of the Metal Interface in Lithium Metal–Garnet Batteries

The interface between solid electrolytes and Li metal is a primary issue for solid‐state batteries. Introducing a metal interlayer to conformally coat solid electrolytes can improve the interface wettability of Li metal and reduce the interfacial resistance, but the mechanism of the metal interlayer is unknown. In this work, we used magnesium (Mg) as a model to investigate the effect of a metal coating on the interfacial resistance of a solid electrolyte and Li metal anode. The Li–Mg alloy has low overpotential, leading to a lower interfacial resistance. Our motivation is to understand how the metal interlayer behaves at the interface to promote increased Li‐metal wettability of the solid electrolyte surface and reduce interfacial resistance. Surprisingly, we found that the metal coating dissolved in the molten piece of Li and diffused into the bulk Li metal, leading to a small and stable interfacial resistance between the garnet solid electrolyte and the Li metal. We also found that the interfacial resistance did not change with increase in the thickness of the metal coating (5, 10, and 100 nm), due to the transient behavior of the metal interface layer.     

Lithium Ion Pathway within Li7La3Zr2O12‐Polyethylene Oxide Composite Electrolytes

Polymer–ceramic composite electrolytes are emerging as a promising solution to deliver high ionic conductivity, optimal mechanical properties, and good safety for developing high‐performance all‐solid‐state rechargeable batteries. Composite electrolytes have been prepared with cubic‐phase Li₇La₃Zr₂O₁₂ (LLZO) garnet and polyethylene oxide (PEO) and employed in symmetric lithium battery cells. By combining selective isotope labeling and high‐resolution solid‐state Li NMR, we are able to track Li ion pathways within LLZO‐PEO composite electrolytes by monitoring the replacement of ⁷Li in the composite electrolyte by ⁶Li from the ⁶Li metal electrodes during battery cycling. We have provided the first experimental evidence to show that Li ions favor the pathway through the LLZO ceramic phase instead of the PEO‐LLZO interface or PEO. This approach can be widely applied to study ion pathways in ionic conductors and to provide useful insights for developing composite materials for energy storage and harvesting.     

Excellent Stability of a Lithium‐Ion‐Conducting Solid Electrolyte upon Reversible Li+/H+ Exchange in Aqueous Solutions

Batteries with an aqueous catholyte and a Li metal anode have attracted interest owing to their exceptional energy density and high charge/discharge rate. The long‐term operation of such batteries requires that the solid electrolyte separator between the anode and aqueous solutions must be compatible with Li and stable over a wide pH range. Unfortunately, no such compound has yet been reported. In this study, an excellent stability in neutral and strongly basic solutions was observed when using the cubic Li₇La₃Zr₂O₁₂ garnet as a Li‐stable solid electrolyte. The material underwent a Li⁺/H⁺ exchange in aqueous solutions. Nevertheless, its structure remained unchanged even under a high exchange rate of 63.6 %. When treated with a 2 M LiOH solution, the Li⁺/H⁺ exchange was reversed without any structural change. These observations suggest that cubic Li₇La₃Zr₂O₁₂ is a promising candidate for the separator in aqueous lithium batteries.