An Electrochemical Sensor for the Detection of Cu2+ Based on Gold Nanoflowers‐modifed Electrode and DNAzyme Functionalized Au@MIL‐101 (Fe)

In this study, we developed an electrochemical sensor for sensitive detection of Cu²⁺ based on gold nanoflowers (AuNFs)‐modified electrode and DNAzyme functionalized Au@MIL‐101(Fe) (MIL: Materials of Institute Lavoisier). The AuNFs‐modified indium tin oxide modified conductive glass electrode(AuNFs/ITO) prepared via electrodeposition showed improved electronic transport properties and provided more active sites to adsorb large amounts of oligonucleotide substrate (DNA1) via thiol‐gold bonds. The stable Au@MIL‐101(Fe) could guarantee the sensitivity because of its intrinsic peroxidase mimic property, while the Cu²⁺‐dependent DNA‐cleaving DNAzyme linked to Au@MIL‐101(Fe) achieved the selectivity toward Cu²⁺. After the DNAzyme substrate strand (DNA2) was cleaved into two parts due to the presence of Cu²⁺, the oligonucleotide fragment linked to MIL‐101(Fe) was able to hybridize with DNA1 adsorbed onto the surface of AuNFs/ITO. Due to the peroxidase‐like catalytic activity of MIL‐101(Fe) and the affinity recognition property of DNAzyme toward Cu²⁺, the electrochemical biosensor showed a sensitive detection range from 0.001 to 100 μM, a detection limit of 0.457 nM and a high selectivity, demonstrating its potential for Cu²⁺ detection in real environmental samples.     

3D Nano‐structure L‐cysteine/AuNPs/Bi2O3 Modified Glass Carbon Electrode as Chemical Sensor for Highly Sensitive and Selective Detection Cu (II)

It was first time using the l‐cysteine self‐assembled on the surface of gold nanoparticles and Bi₂O₃ nano‐structured materials modified GCE composed l‐cysteine/AuNPs/Bi₂O₃/GCE sensor. The sensor possessed three‐dimensional nanostructure and exhibited a higher ratio of activity sites, large active surface, fast electron transfer rate, excellent catalytic, sensing characteristics and larger affinity to Cu (II). The sensor was determined to have an excellent sensitivity and selectivity for the detection of Cu (II). The characterization of sensor as well as the optimization of the analytical procedure was reported. The optimized conditions parameters allowed the detection of Cu (II) concentration following short analysis time, a detection limit of 5×10^?11 M at 80 s of preconcentration time was obtained using the as‐prepared sensor, and also show excellent stability and good repeatability, and, thus, could be used for detection of Cu (II) in environment.     

A High Sensitivity Electrochemical Sensor Based on Fe3+‐Ion Molecularly Imprinted Film for the Detection of T‐2 Toxin

The excellent detection sensitivity in various matrices of T‐2 toxin (T‐2), which has cytotoxic and immunosuppressive effects in DNA and RNA synthesis, is a highly desirable characteristic. A sensitive molecularly imprinted electrochemical sensor was constructed for the selective detection of T‐2. In this study, iron ions (Fe³⁺) were introduced to increase the chelation of the metal ions and templates for preparing molecularly imprinted polymers (MIPs). With the increased chelation of the metal ions and templates, the selectivity and sensitivity of the MIPs were effectively improved. The imprinted sensor was successfully employed to detect T‐2 in cereals and human serum samples.     

仪器分析综合实验:MoS2/MIL-101(Fe)的制备、表征及其光催化降解布洛芬的研究

采用溶剂热的方法制备出MoS2/MIL-101（Fe）纳米复合型催化剂,通过X射线衍射、固体紫外-可见漫反射光谱、傅里叶红外光谱、扫描电子显微镜对催化剂的结构和形态进行表征。并用该催化剂对布洛芬（Ibuprofen,IBP）进行光催化降解,采用高效液相色谱对IBP光催化降解前后的浓度进行定量分析,采用高效液相色谱-质谱联用仪对IBP光催化降解产物进行定性分析。本实验将制备复合材料的方法与多种仪器分析方法相结合,让学生了解材料制备方法及其应用的同时,着重学习了各种分析测试仪器的使用方法和基本原理。     

Electrochemical Sensor Based on Thioether Oligomer Poly(N‐vinylpyrrolidone)‐modified Gold Electrode for Bisphenol A Detection

Presently, bisphenol A (BPA) has been added to the list of substances of very high concern as endocrine disruptors. According to the literature, exposure to bisphenol A even at low doses may result in adverse health effects. In this study, electrochemical sensor of Bisphenol A based on thioether DDT‐Poly(N‐vinylpyrrolidone) oligomer has been developed. The thioether oligomer, which is capable of recognizing BPA, was prepared and used for gold electrode modification. The characterization of the modified gold electrode and the synthesized thioether oligomer were carried out by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), atomic force microscopy (AFM), Fourier‐transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance spectroscopy (¹H NMR) and Size exclusion chromatography (SEC). Obtained results indicate that the modified electrode shows good electrochemical activity, good sensitivity and reproducibility for BPA detection. It exhibited a good linear relationship ranging from 1 to 20 pg/mL, and the detection limit was found to be 1.9 pg/mL at S/N=3. Several interfering species such as hydroquinone, phenol and resorcinol were used and their behaviors on the modified gold electrode were investigated.     

Electrochemical Determination of Cu(II) Ions by 4‐Formylphenylboronic Acid Modified Gold Electrode

A self‐assembled monolayer (SAM) modified by 4‐formylphenylboronic acid was formed on the gold electrode, which was applied for the determination of trace concentrations of Cu(II). The formation of advanced SAM on the gold electrode was evidenced by electrochemical impedance spectroscopy, atomic force microscopy and contact angle measurements. Electrochemical determination of Cu(II) ions was performed by square wave voltammetry. Some mutual interferences caused by Cd(II), Co(II), Fe(II), Ni(II) and Pb(II) ions were investigated and it was demonstrated how the negative effects of these interfering ions could be eliminated by adjustment of proper parameters of square wave voltammetry.     

Fe3O4/MIL‐101(Fe) nanocomposite as an efficient and recyclable catalyst for Strecker reaction

A highly porous metal‐organic framework, MIL‐101(Fe), was prepared by a solvothermal method in the presence of amino‐modified Fe₃O₄@SiO₂ nanoparticles, in order to achieve Fe₃O₄/MIL‐101(Fe) nanocomposite, which was characterized by XRD, FT‐IR, SEM, TEM, BET, and VSM. This hybrid magnetic nanocomposite was employed as heterogeneous catalyst for α‐amino nitriles synthesis through three‐component condensation reaction of aldehydes (ketones), amines, and trimethylsilyl cyanide in EtOH, at room temperature. The recoverability and reusability was admitted for the heterogeneous magnetic catalyst; no significant reduction of catalytic activity was observed even after five consecutive reaction cycles.     

Electrochemical Sensor Based on Multi‐walled Carbon Nanotube/Gold Nanoparticle Modified Glassy Carbon Electrode for Detection of Estradiol in Environmental Samples

We report a rapid and simple method for sensing estradiol by electro‐oxidation on a multi‐walled carbon nanotube (MWCNT) and gold nanoparticle (AuNP) modified glassy carbon electrode (GCE). Compared with a bare GCE, AuNP/GCE and MWCNT/GCE, the composite modified GCE shows an enhanced response to estradiol in 0.1 M phosphate buffer solution. Experimental parameters, including pH and accumulation time for estradiol determination were optimised at AuNP/MWCNT/GCE. A pH of 7.0 was found to be optimum pH with an accumulation time of 5 minutes. Estradiol was determined by linear sweep voltammetry over a dynamic range up to 20 %mol L^?1 and the limit of detection was estimated to be 7.0×10^?8 mol L^?1. The sensor was successfully applied to estradiol determination in tap water and waste water.     

An Enzyme‐free H2O2 Sensor Based on Poly(2‐Aminophenylbenzimidazole)/Gold Nanoparticles Coated Pencil Graphite Electrode

A poly(2‐aminophenylbenzimidazole)/gold nanoparticles (P2AB/AuNPs) coated disposable pencil graphite electrode (PGE) was fabricated as an enzyme‐free sensor for the H₂O₂ determination. P2AB/AuNPs and P2AB were successfully synthesized electrochemically on PGE in acetonitrile for the first time. The coatings were characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, Energy‐dispersive X‐ray spectroscopy, Surface‐enhanced Raman spectroscopy, and UV‐Vis spectroscopy. AuNPs interacted with P2AB as carrier enhances the electrocatalytic activity towards reduction of H₂O₂. The analytical performance was evaluated in a 100 mM phosphate buffer solution at pH 6.5 by amperometry. The steady state current vs. H₂O₂ concentration is linear in the range of 0.06 to 100 mM (R²=0.992) with a limit of detection 3.67×10^?5 M at ?0.8 V vs. SCE and no interference is caused by ascorbic acid, dopamine, uric acid, and glucose. The examination for the sensitive determination of H₂O₂ was conducted in commercially available hair oxidant solution. The results demonstrate that P2AB/AuNPs/PGE has potential applications as a sensing material for quantitative determination of H₂O₂.     

Comparative Studies of Some Novel Cu2+ and Fe3+ Chelates Derived From Tricine (L1) by Single Crystal X‐ray,Spectroscopic and Biological Data: Applications to Investigate Antitumor Activity

Novel Cu ²⁺ and Fe ³⁺ chelates derived from L ¹ were synthesized and characterized by single crystal X‐ray diffraction. The results indicate that the Fe (III) crystal, [Fe(L¹‐H)Cl₂], has an orthorhombic structure of the type pc2b while the dimeric Cu (II) crystal, [Cu(L¹‐H)Cl … ClCu(L¹‐H)], has a monoclinic with space group Cc. X‐ray diffraction and spectroscopic studies revealed that L ¹ acts as monobasic tetradentate with octahedral geometry in Fe (III) crystal while it behaves as dibasic tetradentate with distorted‐octahedral in the Cu (II) crystal. Also, the two chelates were characterized by spectral, magnetic and thermal analyses. DFT parameters were used to prove the liberation of a proton from COOH rather than NH groups. The kinetic and thermodynamic parameters of Fe (III) chelate were determined by Coats‐Redfern and Horowitz‐Metzger methods. Cyclic voltammogram provides information about the oxidation states of Cu (II) and Fe (III) chelates. Antitumor activity against Epitheliod carcinoma (Hela), breast cancer (MCF‐7) and antibacterial activities of chelates were investigated.     

Non‐covalent Immobilization of Iron‐triazole (Fe(Htrz)3) Molecular Mediator in Mesoporous Silica Films for the Electrochemical Detection of Hydrogen Peroxide

Mesoporous silica thin films encapsulating a molecular iron‐triazole complex, Fe(Htrz)₃ (Htrz=1,2,4,‐1H‐triazole), have been generated by electrochemically assisted self‐assembly (EASA) on indium‐tin oxide (ITO) electrode. The obtained modified electrodes are characterized by well‐defined voltammetric signals corresponding to the Fe^II/III centers of the Fe(Htrz)₃ species immobilized into the films, indicating fast electron transfer processes and stable operational stability. This is due to the presence of a high density of redox probes in the material (1.6×10^?4 mol g^?1 Fe(Htrz)₃ in the mesoporous silica film) enabling efficient charge transport by electron hopping. The mesoporous films are uniformly deposited over the whole electrode surface and they are characterized by a thickness of 110 nm and a wormlike mesostructure directed by the template role played by Fe(Htrz)₃ species in the EASA process. These species are durably immobilized in the material (they are not removed by solvent extraction). The composite mesoporous material (denoted Fe(Htrz)₃@SiO₂) is then used for the electrocatalytic detection of hydrogen peroxide, which can be performed by amperometry at an applied potential of ?0.4 V versus Ag/AgCl and by flow injection analysis. The organic‐inorganic hybrid film electrode displays good sensitivity for H₂O₂ sensing over a dynamic range from 5 to 300 μM, with a detection limit estimated at 2 μM.     

方波脉冲法制备Cu_2O@Cu/TiO_2三维阵列纳米复合材料及其作为高灵敏无酶型葡萄糖传感器的研究

采用阳极氧化法制备了TiO_2三维阵列纳米管(TiO_2 NTAs),再利用方波脉冲法在TiO_2 NTAs表面电沉积Cu薄膜,经过煅烧处理后得到Cu_2O@Cu/TiO_2 NTAs纳米复合材料。X-射线衍射仪(XRD)测试表明该材料中Cu和Cu_2O共存。扫描电镜(SEM)和透射电镜(TEM)分析显示,TiO_2管壁的外表面均匀生长Cu_2O,选区电子衍射结果表明该纳米复合材料为混晶材料。差分脉冲伏安法表明,Cu_2O@Cu/TiO_2 NTAs在+0.56 V处出现明显的葡萄糖氧化峰,表明该纳米复合材料对葡萄糖具有强的电催化作用,可用于葡萄糖的测定。计时电流法得到葡萄糖的线性范围为0.19～3.5 mmol/L,灵敏度为372.0μA·L·mmol~(-1)·cm~(-2),检出限为3μmol/L。交流阻抗测得Cu_2O/TiO_2 NTAs的传荷阻抗为526.2Ω,Cu_2O@Cu/TiO_2 NTAs为1.8Ω,二者相差292倍,说明Cu作为中间过渡层降低了电子传导的传荷阻抗。将该电极用于血清中葡萄糖含量的检测,测试结果与医院测定结果无显著差异。Cu_2O@Cu/TiO_2 NTAs可作为一种灵敏度高、响应速度快、选择性较好的无酶型葡萄糖传感器。     

Infrared study of νOD modes in isotopically dilute (HDO) isostructural compounds M(HCOO)2·2H2O (M=Mn,Fe,Co,Ni,Cu,Zn) with matrix-isolated guest ions (Cu in M(HCOO)2·2H2O and M in Cu(HCOO)2·2H2O)

The infrared spectra of isotopically dilute (matrix-isolated HDO molecules) isostructural compounds M(HCOO)₂·2H₂O (M=Mn,Fe,Co,Ni,Zn,Cu) are presented and discussed in the region of the OD stretching modes. According to the structural data the compounds under study are divided into two groups: in M(HCOO)₂·2H₂O (M=Mn,Ni,Zn) the H₂O(1) molecules form stronger hydrogen bonds as compared to H₂O(2); in M(HCOO)₂·2H₂O (M=Fe,Co,Cu) the H₂O(2) molecules form stronger hydrogen bonds as compared to the H₂O(1) molecules. The influence of the metal–water interactions (synergetic effect) and the unit-cell volumes (repulsion potential of the lattice) on the hydrogen bond strength within the isostructural series is discussed. The wavenumbers of the uncoupled OD stretching modes of the HDO molecules influenced by guest ions (Cu²⁺ ions matrix-isolated in M(HCOO)₂·2H₂O and M²⁺ ions matrix-isolated in Cu(HCOO)₂·2H₂O) are presented and commented. For example, the analysis of the spectra reveals that when Cu²⁺ ions are included in the structure of M(HCOO)₂·2H₂O the hydrogen bonds of the type M–OH₂OCHO–Cu are considerably weaker as compared to those of the same type formed when M²⁺ ions are included in the structure of Cu(HCOO)₂·2H₂O if the cations remain unchanged.