An Arrayed Micro‐glutamate Sensor Probe Integrated with On‐probe Ag/AgCl Reference and Counter Electrodes

Complete all‐in‐one multi‐arrayed glutamate (Glut) sensors have been constructed on a silicon‐based micromachined probe composed of micro‐platinum (Pt) working electrodes, a micro‐silver/silver chloride (Ag/AgCl) reference electrode (RE), and a micro‐Pt counter electrode (CE). The OCP shift of the electrodeposited Ag/AgCl on‐probe micro‐reference electrode compared with a Ag/AgCl wire is <0.1 mV/h. The composition ratio of Ag, Cl, and Pt on the electrodeposited on‐probe micro‐reference electrode is observed to be 1.00 : 0.48 : 0.02 analyzed by EDS. The miniaturized amperometric Glut biosensors were constructed on working electrode sites (electrode area: ∼8.5×10⁻⁵ cm²) of the microprobe modified with glutamate oxidase (GlutOx) enzyme layers for the selective, fast, and continuous detection of L‐glutamate. The sensor selectivity towards common electroactive interferents has been improved significantly by coating the electrode surface with perm‐selective polymer layers, overoxidized polypyrrole (PPY) and Nafion®. The sensitivity, detection range, and response time of the proposed all‐in‐one Glut biosensors are 204.7±5.8 nA μM⁻¹ cm⁻² (N=5), 4.99–109 μM, and 2.7±0.3 sec, respectively and no interferent signals of AA and DA were observed. The sensor can be reused over 19 times of continuous repetitive operation (total measurement time: ∼4 hours) and the sensor sensitivity can retain up to four weeks of storage.     

Choice of Reference Electrode is Critical for Potentiometric Whole Cell‐based Sensor

Cells have a net negative outer charge which gives rise to a potential difference in a potentiometric set up. Here, Triton X‐100 was used as a model toxin and the cell death was monitored by the potential change, noticed as decrease in negativity. Hence, cytotoxicity can be tested in vitro and real‐time using potentiometry. However, silver ions (Ag⁺) and/or silver chloride ions (AgCl₂)^?1 lead to cell death when we used the standard Ag/AgCl reference electrode with 3 M NaCl as filling solution. Our further experimentation showed that PBS as filling solution was biocompatible and also gave stable potentiometric profiles.     

Improvement of the silver/silver chloride reference electrode and its application to pH measurement

When a silver/silver chloride (Ag AgCl ) reference electrode was used continuously in a low conductivity solution or reductive solution, it was often observed that stability of the liquid junction potential was lost. This phenomenon was remarkable with a Ag AgCl reference electrode compared to a calomel reference electrode. We found that 340 mg l(-1) of silver was dissolved in 3 M potassium chloride (KCl) internal solution as silver complex ions (AgCl(-(x-1))(x)) for x = 2 or 3. However, only 1.93 mg l(-1) of silver chloride (AgCl) can theoretically be dissolved in water. The complex ion that effused into the sample solution through the liquid junction clogged the liquid junction (e.g. porous ceramic) as AgCl, or as metallic silver (Ag) in reducing solution. Therefore, the constant effusion of KCl internal solution was inhibited, and the liquid junction potential became unstable or fluctuating. A new reference electrode was developed, which can eliminate AgCl(-(x-1))(x) in 3 M KCl internal solution by the use of chelating resins. A combination of this reference electrode with a pH electrode made long-term stable pH measurements possible.     

Stripping Chronopotentiometry with Dry‐Preservable Supporting Electrolyte

The determination of some toxic metals by stripping chronopotentiometry with a supporting solution having an unconventional composition has been investigated with the aim of using such components in disposable measuring cells preservable in dry state and quite ready for use, only needing addition of a small volume of sample. The new supporting solution is prepared with a solid strong acid, p‐toluenesulfonic acid, in the place of the inorganic acids commonly used to improve the cation availability. The other components are, as usual, sodium chloride, which fixes the potential of the screen‐printed silver – silver chloride reference electrode, and mercury(II) chloride as the plating agent. This supporting solution has been tested in batch measurements with the mercury film glassy carbon electrode as well as with screen‐printed carbon‐ink electrodes, either with mercury film or bare. The physical shape of the mercury layer electrolytically deposited on screen‐printed carbon‐ink electrodes from a supporting solution containing 0.1 M p‐toluenesulfonic acid and 0.1 M sodium chloride has been investigated by scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) microanalysis. In chronopotentiometric stripping p‐toluenesulfonic acid performs as well as the usual inorganic strong acids, particularly in terms of sensitivity. At 0.1 mol dm^?3 it proved very suitable for the determination of toxic metals, in particular lead(II), at levels down to a few μg dm^?3. The overall results appear promising and can open new avenues for preparing disposable cells for on‐field stripping chronopotentiometric determination of toxic metals.     

Disposable Injection‐Moulded Cell‐on‐a‐Chip Microfluidic Devices with Integrated Conducting Polymer Electrodes for On‐Line Voltammetric and Electrochemiluminescence Detection

This work reports the construction and characterization of plastic electrochemical micro‐flow‐cells with integrated injection‐moulded polymer electrodes. The three electrodes (working, auxiliary, and reference) were fabricated by injection‐moulding from a conducting grade of polystyrene loaded with carbon fibers. On‐chip reference electrodes were prepared by coating one of the conducting polymer electrodes with a Ag/AgCl layer (implemented either by e‐beam evaporation of Ag followed by electrochemical formation of AgCl or by applying a Ag/AgCl paste). Working electrodes were either polymer electrodes coated with Au by e‐beam evaporation or bare conducting polymer electrodes. The electrodes were integrated into the micro‐flow‐cells by an over‐moulding process followed by ultrasonic welding. The devices were characterized by optical and electrochemical techniques. Studies by cyclic voltammetry (CV), anodic stripping voltammetry (ASV) and electrochemiluminescence (ECL) demonstrate ‘proof–of‐principle’ of the micro‐flow‐cells as electrochemical sensors.     

Seed‐Mediated Growth of Silver Nanocubes in Aqueous Solution with Tunable Size and Their Conversion to Au Nanocages with Efficient Photothermal Property

Two seed‐mediated approaches for the growth of silver nanocubes in aqueous solution have been developed. Addition of a silver‐seed solution to a mixture of cetyltrimethylammonium chloride (CTAC), silver trifluoroacetate, and ascorbic acid and heating the solution at 60 °C for 1.5 h produces uniform Ag nanocubes with tunable sizes from 23 to 60 nm by simply adjusting the volume of silver‐seed solution introduced. Alternatively, the silver‐seed solution can be injected into a mixture of cetyltrimethylammonium bromide (CTAB), silver nitrate, copper sulfate, and ascorbic acid and heated to 80 °C for 2 h to generate 46 nm silver nanocubes. Plate‐like Ag nanocrystals exposing {111} surfaces can be synthesized by reducing Ag(NH₃)₂⁺ with ascorbic acid in a CTAC solution. Relatively large Ag nanocubes were converted to cuboctahedral Au/Ag and Au nanocages and nanoframes with empty {111} faces through a galvanic replacement reaction. The nanocages showed a progressive plasmonic band red‐shift with increasing Au content. The nanocages exhibited high and stable photothermal efficiency with solution temperatures quickly reaching beyond 100 °C when irradiated with an 808 nm laser for large heat and water vapor generation.     

Preparation and resistivity study of silver nanocomposite films using spin‐assisted layer‐by‐layer assembly

Nanocomposite films [Ag/(PAH‐PSS)_nPAH]_m were fabricated on a silicon substrate using a time‐ and cost‐efficient spin‐assisted layer‐by‐layer (SA‐LbL) self‐assembly technique. A virtually monolayer‐like layer of self‐assembled silver nanoparticles was formed when deposition time increased to 30 min. It was found that polymer multilayers could effectively decrease the resistivity of silver nanoparticle monolayer, which was far higher than that of bulk silver metal; however, the resistivity of Ag/(PAH‐PSS)_nPAH multilayer films increased along with the increasing of the number of polymer bilayers. XPS investigations showed that silver nanoparticles were partially oxidized, which might be the major cause of the high resistivity of silver nanoparticle monolayer. Copyright © 2008 John Wiley & Sons, Ltd.     

Determination of Amino Acids at a Silver Oxide/Silver Phosphate Electrode and the Analysis of Structure‐Response Relationships

When a silver electrode is conditioned in a solution of 0.5 M sodium hydroxide with added sodium phosphate and using a dual pulse (500 mV/750 mV vs. Ag/AgCl), a stable silver(I)/silver(II) oxide surface is formed. It has been previously shown that various moieties react with the silver(II) oxide in a chemical oxidation at the outer surface of the oxide layer. This is then followed by re‐oxidation of the silver with the generation of current at approximately 500 mV relative to the silver/silver chloride electrode. Previously we found the need to remove carbon dioxide from the base and condition the electrode in a solution containing phosphate ion in order to provide mechanical stability to the oxide layer. We have previously shown this electrode to be applicable to the detection of a variety of carbohydrates. The applicability of the silver oxide/silver phosphate electrode to the post‐chromatographic amperometric detection of amino acids was investigated. Calibration studies of amino acids representative of the various classes demonstrated good sensitivity and linearity in the 1–100 μM range. Responses of amino acids were measured using glucose as an external standard, in order to correct for variability of the oxide layer. Relative responses of the amino acids ranged from 3 down to 0.1. Correlation with structure suggested the importance of absorption in determining the rate of oxidation. Comparison of arginine with n‐benzoyl‐L ‐arginine ethyl ester indicated that side chains as well as the backbone amino group can be oxidized. A Levitch plot of alanine was shown to be linear from approximately 30 to 300 radians per second spin rate at a scan rate of 50 mV per second. Application to post‐chromatographic detection was demonstrated.     

A Simple Hydrothermal Route to Large‐Scale Synthesis of Uniform Silver Nanowires

This paper describes the preparation of uniform silver nanowires by reducing freshly prepared silver chloride with glucose at 180 °C for 18 hours in the absence of any surfactants or polymers. Scanning electron microscopy studies indicated that the silver nanowires are about 100 nm in diameter and up to 500 μm in length. High‐resolution transmission electron microscopy analyses showed that the silver nanowires grow perpendicularly to the Ag(200) plane. The silver nanowires are believed to grow through a solid–solution–solid process. Some influential factors on the growth of silver nanowires are also discussed.     

All‐Solid‐State Chloride Sensors with Poly(3‐Octylthiopene) Matrix and Trihexadecylmethylammonium Chlorides as an Ion Exchanger Salt

All‐solid‐state chloride sensors were prepared by incorporation of trihexadecyl‐methylammonium chloride (THMACl) as an ion‐exchanger salt into a conjugated polymer membrane, poly(3‐octylthiophene) (POT). The influence of additional membrane components, such as a lipophilic anion, (potassium tetrakis[3,5‐bis(trifluoromethyl)phenyl] borate), poly(vinyl chloride) (PVC) or a plasticizer, (2‐nitrophenyl octyl ether) were studied. The membrane components were dissolved in chloroform except for PVC, which was dissolved in tetrahydrofuran (THF). The membrane solution was deposited on glassy carbon (GC) by solution casting resulting in all‐solid‐state chloride sensors. The sensor characteristics were determined potentiometrically and with impedance spectroscopy. The addition of plasticizer was found to be crucial in obtaining a well functioning Cl^?‐ISE based on POT and THMACl.     

Poly[(μ2‐2,2‐dimethylpropane‐1,3‐diyl diisocyanide)‐μ2‐nitrato‐silver(I)]: a powder study

In order to investigate the effect of counter‐anions on the polymeric structure of (2,2‐dimethylpropane‐1,3‐diyl diisocyanide)silver(I) complexes, the novel title polymeric compound, [Ag(NO₃)(C₇H₁₀N₂)]_n, has been synthesized. The crystal structure was determined by simulated annealing from X‐ray powder diffraction data collected at room temperature. The current structure is similar to the recently reported structure of the analogue with chloride replacing nitrate. This study illustrates that both the chloride and nitrate complexes crystallize in the orthorhombic system in the Pbca space group with one monomer in the asymmetric unit, and also gives a strong indication that the counter‐anion does not have a considerable effect on the polymeric structure of the complex. The Ag centre lies in a distorted tetrahedral environment and is bonded to two 2,2‐dimethylpropane‐1,3‐diyl diisocyanide ligands to form chains. The nitrate anions crosslink the Ag centres of the chains to form a two‐dimensional polymeric network structure.     

Flow Injection Analysis of Aluminum Chlorohydrate in Antiperspirant Deodorants Using a Built‐in Three‐in‐one Screen‐Printed Silver Electrode

A screen‐printed silver strip with a built‐in three‐in‐one electrode (SPAgE) configuration of Ag‐working, Ag‐counter and Ag/Ag_xO (silver oxides) pseudoreference electrodes has been developed for sensitive and selective electrochemical flow injection analysis (FIA) of aluminum chlorohydrate (ACH) present in antiperspirants, through the free Cl^? ion liberated from ACH in aqueous medium, as a redox signal at Ag‐working electrode in pH 6 phosphate buffer solution (PBS). The solution phase and instrumental parameters were systematically optimized. The calibration graph was linear in the window 1–200 ppm concentration of ACH and the lowest detection limit (S/N=3) was 295 ppb with a slope of 0.0989 μA/ppm and regression coefficient of 0.998. Calculated relative standard deviation (RSD) values for the detection of 5 and 50 ppm ACH by this method are 2.21 % and 2.16 %, respectively. Four different antiperspirant deodorants real samples with and without ACH content were successfully analyzed and the detected values obtained were found to be in good agreement with the product labeled values.     

Fabrication of a Simple and Cheap Screen-printed Silver/Silver Chloride (Ag/AgCl) Quasi-reference Electrode

In this work, a silver/silver chloride ink is fabricated using two steps. First the silver ink is prepare using silver, nail polish and acetone. Then the silver ink is painted in a paper substrate and a silver chloride layer is deposited using a bleach solution. The result is the silver/silver chloride conductive ink. The silver ink is cheap ($2.49/g), well-dispersive and very easy to fabricate. The materials were characterized by SEM and XRD. The Ag ink showed the formation of a continuous network throughout the silver ink film with fewer agglomeration. The effective chlorination process was also observed in the Ag/AgCl characterization. Since the Ag/AgCl substrate will be used as a quasi-reference electrode, it is important to investigate the electrical properties. The Ag ink showed an average ohmic resistance of 2.27 Ω. The addition of the AgCl layer decreases the conductivity, as expected. In summary, the Ag/Ag/Cl ink developed is simple, well-dispersed, cheap and with good conductivity. Therefore, it can be used as a conductive ink in the fabrication of quasi-reference electrodes.     

A microfluidic glucose sensor incorporating a novel thread‐based electrode system

An electrochemical sensor for the detection of glucose using thread‐based electrodes and fabric is described. This device is relatively simple to fabricate and can be used for multiple readings after washing with ethanol. The fabrication of the chip consisted of two steps. First, three thread‐based electrodes (reference, working, and counter) were fabricated by painting pieces of nylon thread with either layered silver ink and carbon ink or silver/silver chloride ink. The threads were then woven into a fabric chip with a beeswax barrier molded around the edges in order to prevent leaks from the tested solutions. A thread‐based working electrode consisting of one layer of silver underneath two layers of carbon was selected to fabricate the final sensor system. Using the chip, a PBS solution containing glucose oxidase (GOx) (10 mg/mL), potassium ferricyanide (K₃[Fe(CN)₆]) (10 mg/mL) as mediator, and different concentrations of glucose (0‐25 mM), was measured by cyclic voltammetry (CV). It was found that the current output from the oxidation of glucose was proportional to the glucose concentrations. This thread‐based electrode system is a viable sensor platform for detecting glucose in the physiological range.     

A Solid‐State Reference Electrode Based on a Self‐Referencing Pulstrode

The design of solid‐state reference electrodes without a liquid junction is important to allow miniature and cost‐effective electrochemical sensors. To address this, a pulse control is proposed using an Ag/AgI element as reliable solid‐state reference electrode. It involves the local release of iodide by a cathodic current that is immediately followed by an electromotive force (EMF) measurement that serves as the reference potential. The recapture of iodide ions is achieved by potentiostatic control. This results in intermittent potential values that are reproducible to less than one millivolt (SD=0.27 mV, n=50). The ionic strength is shown to influence the activity coefficient of released iodide in accordance with the extended Debye–Hückel equation, resulting in a predictable change of the potential reading. The principle is applied to potentiometric potassium detection with a valinomycin‐based ion‐selective electrode (ISE), demonstrating a completely solid‐state sensor configuration.     

A Cryptate Reference Electrode for Ionic Liquids

The cryptate electrode (Ag/Ag⁺222), prepared by immersing silver wire in a solution of silver(I) salt and the cryptand 222 (4,7,13,16,21,24‐hexaoxa‐1,10‐diazabicyclo[8.8.8]hexacosane) in ionic liquids have been studied. The potential of the electrode is stabilized by the equilibrium of the Ag⁺ ion complexation by the cryptand, similarly to the potential stabilization by the ionic product of slightly soluble salts, used in aqueous electrodes of the second kind. The Ag/Ag⁺222 cryptate electrode (concentration of the cryptate was much higher than the silver(I) cation concentration, [222]>[Ag⁺]) may be used as a reference electrode in room temperature ionic liquids. The potential of the Ag/Ag⁺222 electrode is less sensitive to the presence of impurities, such as halides or water, in comparison to the Ag/Ag⁺ electrode. After anodic or cathodic polarization, the potential of the Ag/Ag⁺222 electrode comes back to the initial open circuit potential quickly. Preparation of the Ag/Ag⁺222 reference electrode is very easy: a silver wire is immersed in a solution of Ag⁺ salt and cryptand 222 (both available commercially) in the ionic liquid under study.     

A Self‐contained Two‐electrode Nanosensor for Electrochemical Analysis in Aqueous Microenvironments

We describe the development, fabrication, and characterization of a novel two‐electrode nanosensor contained within the tip of a needle‐like probe. This sensor consists of two, vertically aligned, carbon structures which function as individual electrodes. One of the carbon structures was modified by silver electrodeposition and chlorination to enable it to function as a pseudo‐reference electrode. Performance of this pseudo‐reference electrode was found to be comparable to that of commercially available Ag/AgCl reference electrodes. The unmodified carbon structure was employed as a working electrode versus the silver‐plated carbon structure to form a two‐electrode sensor capable of characterizing redox‐active analytes. The nanosensor was demonstrated to be capable of electrochemically characterizing the redox behavior of para‐aminophenol (PAP) in both bulk solutions and microenvironments. PAP was also measured in cell lysate to show that the nanosensor can detect small concentrations of analyte in heterogenous environments. As the working and reference electrodes are contained within a single nanoprobe, there was no requirement to position external electrodes within the electrochemical cell enabling analysis within very small domains. Due to the low‐cost manufacturing process, this nanoprobe has the potential to become a unique and widely accessible tool for the electrochemical characterization of microenvironments.     

Synthesis of Silver Nanoparticles Using Ionic‐Liquid‐Based Microwave‐Assisted Extraction from Polygonum minus and Photodegradation of Methylene Blue

A green biogenic, nontoxic, high‐yielding synthetic method is introduced for the synthesis of silver nanoparticles (AgNPs) using ionic‐liquid‐based, microwave‐assisted extraction (ILMAE) from Polygonum minus . The aqueous ionic liquid (1‐butyl‐3‐methylimidazolium chloride [BMIM]Cl)‐based plant extract was used as reducing agent to reduce silver ions to AgNPs. The synthesis of AgNPs was confirmed by UV–visible spectrophotometry. Fourier transforms infrared (FTIR) spectra showed that the plant bioactive compounds capped the AgNPs. The particle size and morphology of Ag NPs were characterized by dynamic light scattering (DLS) and field emission scanning electron microscopy (FESEM), respectively. Elemental analysis was carried out by energy‐dispersive X‐ray (EDX) spectroscopy. Photodegradation studies showed that the AgNPs degraded 98% of methylene blue in 12 min.     

A Facile One‐Pot Synthesis of Layered Protonated Titanate Nanosheets Loaded with Silver Nanoparticles with Enhanced Visible‐Light Photocatalytic Performance

Layered protonated titanate nanosheets (LPTNs) loaded with silver nanoparticles are prepared by a simple one‐pot hydrothermal route in silver‐ammonia solution. The as‐synthesized Ag‐loaded LPTNs possess large specific surface area. The Ag nanoparticles are highly dispersed on the surface of the LPTNs. They have negligible effects on the crystal structure, crystallinity, and surface area of the LPTNs but result in considerable enhancement of visible‐light absorption and in a red‐shift of the band gap for the LPTNs. The Ag‐loaded LPTNs show enhanced photocatalytic activity for both liquid‐ and gas‐phase reactions under visible‐light irradiation. Moreover, the photocatalytic activity first increases gradually with increasing Ag loading content, and then decreases after maximizing at an optimal Ag content. At the Ag loading content of 2.87 mol % and 1.57 mol %, the Ag‐loaded LPTNs exhibit the highest visible‐light photocatalytic activity for degradation of rhodamine B in water and mineralization of benzene in air, respectively. An alternative possible mechanism for the enhancement of the visible‐light photocatalytic activity is also proposed.     

UV‐curing synthesis of sulfonated polyaniline‐silver nanocomposites by an in situ reduction method

Sulfonated polyaniline‐silver (SPAni‐Ag) hybrid nanocomposites have been synthesized by the in situ reduction using a UV‐curing polymerization method without using any reducing or binding agent. An aqueous solution of aniline and orthoanilinic acid (OA) comonomers, a free‐radical oxidant and silver metal salts were irradiated by UV rays. Reduction of the silver salt in aqueous aniline and OA leads to the formation of silver particles which in turn catalyze the oxidation of comonomers to sulfonated polyaniline (SPAni). The resultant SPAni‐Ag nanocomposites were characterized by using different spectroscopy analyses like UV–visible (UV–Vis), X‐ray diffraction (XRD) and infrared spectroscopy. The absorption bands were revealed to be optically active and the peaks blue‐shifted due to the presence of metallic silver within the SPAni matrix. The XRD patterns displayed both the broad amorphous polymeric and sharp metallic peaks. Scanning electron microscopy and transmission electron microscopy of the nanocomposites showed a uniform size distribution with spherical and granular morphology. Thermogravimetric analysis revealed that the nanocomposites had a better thermal stability than the bulk SPAni. Copyright © 2008 John Wiley & Sons, Ltd.