Electrochemical lithium and sodium insertion studies in 3D metal oxy-phosphate framework MoWO3(PO4)2 for battery applications

A new type of three-dimensional (3D) oxy-phosphate materials are explored for the application of Li and Na batteries. The molybdenum tungsten oxy phosphate, MoWO₃(PO₄)₂, was synthesized by solid-state method and evaluated for Li/Na insertion/de-insertion electrode material for the first time. The cell at charged state (vs. Li⁺/Li) showed a discharge capacity of 786 mAh g⁻¹ within the voltage window of 0.3 V with amorphization of crystalline MoWO₃(PO₄)₂ as observed from ex-situ powder XRD analysis. The structural integrity was revealed in this material, even with nearly more than 5 Li⁺ ions into the lattice, leading to the discharge capacity of 250 mAh g⁻¹. The reversible charge/discharge behavior with insertion/de-insertion of 2.4 Li⁺ ions in the voltage range of 1.65 − 3.5 V resulted in 110 and 95 mAh g⁻¹ at C/10 and C/5 rates, respectively. On the other hand, poor cycling performance was noticed for Na ion insertion and desertion, with a discharge capacity of 250 mAh/g within the voltage range of 0.3 − 3.5 V (vs. Na⁺/Na).

     

Towards Highly Stable Storage of Sodium Ions: A Porous Na3V2(PO4)3/C Cathode Material for Sodium‐Ion Batteries

A porous Na₃V₂(PO₄)₃ cathode material coated uniformly with a layer of approximately 6 nm carbon has been synthesized by the sol–gel method combined with a freeze‐drying process. The special porous morphology and structure significantly increases the specific surface area of the material, which greatly enlarges the contact area between the electrode and electrolyte, and consequently supplies more active sites for sodium ions. When employed as a cathode material of sodium‐ion batteries, this porous Na₃V₂(PO₄)₃/C exhibits excellent rate performance and cycling stability; for instance, it shows quite a flat potential plateau at 3.4 V in the potential window of 2.7–4.0 V versus Na⁺/Na and delivers an initial capacity as high as 118.9 and 98.0 mA h g^?1 at current rates of 0.05 and 0.5 C, respectively, and after 50 cycles, a good capacity retention of 92.7 and 93.6 % are maintained. Moreover, even when the discharge current density is increased to 5 C (590 mA g^?1), an initial capacity of 97.6 mA h g^?1 can still be achieved, and an exciting capacity retention of 88.6 % is obtained after 100 cycles. The good cycle performance, excellent rate capability, and moreover, the low cost of Na₃V₂(PO₄)₃/C suggest that this material is a promising cathode for large‐scale sodium‐ion rechargeable batteries.     

LiZr4(PO4)3的Na/Li及Ag/Li离子交换

研究了LiZr2(PO4)3在水溶液中的Na/Li和Ag/Li离子交换行为.结果表明,LiZr2(PO4)3对Na+和Ag+离子均具有很高的选择性,且对Ag+的选择性高于Na+.LiZr2(PO4)3与Ag+的离子交换反应是通过形成固溶体的形式进行的,而与Na+的离子交换反应则是通过置换进行的.温度升高有利于提高LiZr2(PO4)3上Na/Li和Ag/Li的离子交换反应速度.     

Processable and Moldable Sodium‐Metal Anodes

Sodium‐ion batteries are similar in concept and function to lithium‐ion batteries, but their development and commercialization lag far behind. One obstacle is the lack of a standard reference electrode. Unlike Li foil reference electrodes, sodium is not easily processable or moldable and it deforms easily. Herein we fabricate a processable and moldable composite Na metal anode made from Na and reduced graphene oxide (r‐GO). With only 4.5 % percent r‐GO, the composite anodes had improved hardness, strength, and stability to corrosion compared to Na metal, and can be engineered to various shapes and sizes. The plating/stripping cycling of the composite anode was significantly extended in both ether and carbonate electrolytes giving less dendrite formation. We used the composite anode in both Na‐O₂ and Na‐Na₃V₂(PO₄)₃ full cells.     

Superior Na‐Storage Performance of Low‐Temperature‐Synthesized Na3(VO1−xPO4)2F1+2x (0≤x≤1) Nanoparticles for Na‐Ion Batteries

Na‐ion batteries are becoming comparable to Li‐ion batteries because of their similar chemical characteristics and abundant sources of sodium. However, the materials production should be cost‐effective in order to meet the demand for large‐scale application. Here, a series of nanosized high‐performance cathode materials, Na₃(VO_1?xPO₄)₂F_1+2x (0≤x≤1), has been synthesized by a solvothermal low‐temperature (60–120 °C) strategy without the use of organic ligands or surfactants. The as‐synthesized Na₃(VOPO₄)₂F nanoparticles show the best Na‐storage performance reported so far in terms of both high rate capability (up to 10 C rate) and long cycle stability over 1200 cycles. To the best of our knowledge, the current developed synthetic strategy for Na₃(VO_1?xPO₄)₂F_1+2x is by far one of the least expensive and energy‐consuming methods, much superior to the conventional high‐temperature solid‐state method.     

A Cation and Anion Dual Doping Strategy for the Elevation of Titanium Redox Potential for High‐Power Sodium‐Ion Batteries

Titanium‐based polyanions have been intensively investigated for sodium‐ion batteries owing to their superior structural stability and thermal safety. However, their low working potential hindered further applications. Now, a cation and anion dual doping strategy is used to boost the redox potential of Ti‐based cathodes of Na₃Ti_0.5V_0.5(PO₃)₃N as a new cathode material for sodium ion batteries. Both the Ti³⁺/Ti⁴⁺ and V³⁺/V⁴⁺ redox couples are reversibly accessed, leading to two distinctive voltage platforms at ca. 3.3 V and ca. 3.8 V, respectively. The remarkably improved cycling stability (86.3 %, 3000 cycles) can be ascribed to the near‐zero volume strain in this unusual cubic symmetry, which has been demonstrated by in situ synchrotron‐based X‐ray diffraction. First‐principles calculations reveal its well‐interconnected 3D Na diffusion pathways with low energy barriers, and the two‐sodium‐extracted intermediate NaTi_0.5V_0.5(PO₃)₃N is also a stable phase according to formation energy calculations.     

Fast Sodium‐Ion Conductivity in Supertetrahedral Phosphidosilicates

Fast sodium‐ion conductors are key components of Na‐based all‐solid‐state batteries which hold promise for large‐scale storage of electrical power. We report the synthesis, crystal‐structure determination, and Na⁺‐ion conductivities of six new Na‐ion conductors, the phosphidosilicates Na₁₉Si₁₃P₂₅, Na₂₃Si₁₉P₃₃, Na₂₃Si₂₈P₄₅, Na₂₃Si₃₇P₅₇, LT‐NaSi₂P₃ and HT‐NaSi₂P₃, based entirely on earth‐abundant elements. They have SiP₄ tetrahedra assembled interpenetrating networks of T3 to T5 supertetrahedral clusters and can be hierarchically assigned to sphalerite‐ or diamond‐type structures. ²³Na solid‐state NMR spectra and geometrical pathway analysis show Na⁺‐ion mobility between the supertetrahedral cluster networks. Electrochemical impedance spectroscopy shows Na⁺‐ion conductivities up to σ (Na⁺)=4×10^?4 S cm^?1. The conductivities increase with the size of the supertetrahedral clusters through dilution of Na⁺‐ions as the charge density of the anionic networks decreases.     

Ruthenium‐Oxide‐Coated Sodium Vanadium Fluorophosphate Nanowires as High‐Power Cathode Materials for Sodium‐Ion Batteries

Sodium‐ion batteries are a very promising alternative to lithium‐ion batteries because of their reliance on an abundant supply of sodium salts, environmental benignity, and low cost. However, the low rate capability and poor long‐term stability still hinder their practical application. A cathode material, formed of RuO₂‐coated Na₃V₂O₂(PO₄)₂F nanowires, has a 50 nm diameter with the space group of I4/mmm. When used as a cathode material for Na‐ion batteries, a reversible capacity of 120 mAh g^?1 at 1 C and 95 mAh g^?1 at 20 C can be achieved after 1000 charge–discharge cycles. The ultrahigh rate capability and enhanced cycling stability are comparable with high performance lithium cathodes. Combining first principles computational investigation with experimental observations, the excellent performance can be attributed to the uniform and highly conductive RuO₂ coating and the preferred growth of the (002) plane in the Na₃V₂O₂(PO₄)₂F nanowires.     

Cobalt‐Doped FeS2 Nanospheres with Complete Solid Solubility as a High‐Performance Anode Material for Sodium‐Ion Batteries

Considering that the high capacity, long‐term cycle life, and high‐rate capability of anode materials for sodium‐ion batteries (SIBs) is a bottleneck currently, a series of Co‐doped FeS₂ solid solutions with different Co contents were prepared by a facile solvothermal method, and for the first time their Na‐storage properties were investigated. The optimized Co_0.5Fe_0.5S₂ (Fe0.5) has discharge capacities of 0.220 Ah g^?1 after 5000 cycles at 2 A g^?1 and 0.172 Ah g^?1 even at 20 A g^?1 with compatible ether‐based electrolyte in a voltage window of 0.8–2.9 V. The Fe0.5 sample transforms to layered Na_xCo_0.5Fe_0.5S₂ by initial activation, and the layered structure is maintained during following cycles. The redox reactions of Na_xCo_0.5Fe_0.5S₂ are dominated by pseudocapacitive behavior, leading to fast Na⁺ insertion/extraction and durable cycle life. A Na₃V₂(PO₄)₃/Fe0.5 full cell was assembled, delivering an initial capacity of 0.340 Ah g^?1.     

Assembly of Na3V2(PO4)3 Nanoparticles Confined in a One‐Dimensional Carbon Sheath for Enhanced Sodium‐Ion Cathode Properties

Structural and morphological control is an effective approach for improvement of electrochemical properties in rechargeable batteries. One‐dimensionally assembled structure composed of NASICON‐type Na₃V₂(PO₄)₃ nanoparticles were fabricated through an electrospinning method to meet the requirements for the development of efficient electrode materials in Na‐ion batteries. High‐temperature treatment of electrospun precursor fibers under an argon flow provides a nonwoven fabric of nanowires comprising crystallographically oriented nanoparticles of NASICON‐type Na₃V₂(PO₄)₃ within a carbon sheath. The mesostructure comprising NASICON‐type Na₃V₂(PO₄)₃ and carbon give a short sodium‐ion transport pass and an efficient electron conduction pass. Electrochemical properties of NASICON‐type Na₃V₂(PO₄)₃ are improved on the basis of one‐dimensional nanostructures designed in the present study.     

Enhancing Capacity Performance by Utilizing the Redox Chemistry of the Electrolyte in a Dual‐Electrolyte Sodium‐Ion Battery

A strategy is described to increase charge storage in a dual electrolyte Na‐ion battery (DESIB) by combining the redox chemistry of the electrolyte with a Na⁺ ion de‐insertion/insertion cathode. Conventional electrolytes do not contribute to charge storage in battery systems, but redox‐active electrolytes augment this property via charge transfer reactions at the electrode–electrolyte interface. The capacity of the cathode combined with that provided by the electrolyte redox reaction thus increases overall charge storage. An aqueous sodium hexacyanoferrate (Na₄Fe(CN)₆) solution is employed as the redox‐active electrolyte (Na‐FC) and sodium nickel Prussian blue (Na_x‐NiBP) as the Na⁺ ion insertion/de‐insertion cathode. The capacity of DESIB with Na‐FC electrolyte is twice that of a battery using a conventional (Na₂SO₄) electrolyte. The use of redox‐active electrolytes in batteries of any kind is an efficient and scalable approach to develop advanced high‐energy‐density storage systems.     

Carbon coated Na3V2(PO4)3 as novel electrode material for sodium ion batteries

A Na₃V₂(PO₄)₃ sample coated uniformly with a layer of 6 nm carbon has been successfully synthesized by a one-step solid state reaction. This material shows two flat voltage plateaus at 3.4 V vs. Na⁺/Na and 1.63 V vs. Na⁺/Na in a nonaqueous sodium cell. When the Na₃V₂(PO₄)₃/C sample is tested as a cathode in a voltage range of 2.7-3.8 V vs. Na⁺/Na, its initial charge and discharge capacities are 98.6 and 93 mAh/g. The capacity retention of 99% can be achieved after 10 cycles. The electrode shows good cycle performance and moderate rate performance. When it is tested as an anode in a voltage range of 1.0-3.0 V vs. Na⁺/Na, the initial reversible capacity is 66.3 mAh/g and the capacity of 59 mAh/g can be maintained after 50 cycles. These preliminary results indicate that Na₃V₂(PO₄)₃/C is a new promising material for sodium ion batteries.     

Carbon‐Coated LiTi2(PO4)3: An Ideal Insertion Host for Lithium‐Ion and Sodium‐Ion Batteries

We report the extraordinary performance of carbon‐coated sodium super ion conductor (NASICON)‐type LiTi₂(PO₄)₃ as an ideal host matrix for reversible insertion of both Li and Na ions. The NASICON‐type compound was prepared by means of a Pechini‐type polymerizable complex method and was subsequently carbon coated. Several characterization techniques such as XRD, thermogravimetric analysis (TGA), field‐emission (FE) SEM, TEM, and Raman analysis were used to study the physicochemical properties. Both guest species underwent a two‐phase insertion mechanism during the charge/discharge process that was clearly evidenced from galvanostatic and cyclic voltammetric studies. Unlike that of Li (≈1.5 moles of Li), Na insertion exhibits better reversibility (≈1.59 moles of Na) while experiencing a slightly higher capacity fade (≈8 % higher than Li) and polarization (780 mV) than Li. However, excellent rate capability profiles were noted for Na insertion relative to its counterpart Li. Overall, the Na insertion properties were found to be superior relative to Li insertion, which makes carbon‐coated NASICON‐type LiTi₂(PO₄)₃ hosts attractive for the development of next‐generation batteries.     

Quantum and Classical Molecular Dynamics of Ionic Liquid Electrolytes for Na/Li‐based Batteries: Molecular Origins of the Conductivity Behavior

Compositional effects on the charge‐transport properties of electrolytes for batteries based on room‐temperature ionic liquids (RTILs) are well‐known. However, further understanding is required about the molecular origins of these effects, in particular regarding the replacement of Li by Na. In this work, we investigate the use of RTILs in batteries, by means of both classical molecular dynamics (MD), which provides information about structure and molecular transport, and ab initio molecular dynamics (AIMD), which provides information about structure. The focus has been placed on the effect of adding either Na⁺ or Li⁺ to 1‐methyl‐1‐butyl‐pyrrolidinium [C₄PYR]⁺ bis(trifluoromethanesulfonyl)imide [Tf₂N]^?. Radial distribution functions show excellent agreement between MD and AIMD, which ensures the validity of the force fields used in the MD. This is corroborated by the MD results for the density, the diffusion coefficients, and the total conductivity of the electrolytes, which reproduce remarkably well the experimental observations for all studied Na/Li concentrations. By extracting partial conductivities, it is demonstrated that the main contribution to the conductivity is that of [C₄PYR]⁺ and [Tf₂N]^?. However, addition of Na⁺/Li⁺, although not significant on its own, produces a dramatic decrease in the partial conductivities of the RTIL ions. The origin of this indirect effect can be traced to the modification of the microscopic structure of the liquid as observed from the radial distribution functions, owing to the formation of [Na(Tf₂N)_n]^(n?1)? and [Li(Tf₂N)_n]^(n?1)? clusters at high concentrations. This formation hinders the motion of the large ions, hence reducing the total conductivity. We demonstrate that this clustering effect is common to both Li and Na, showing that both ions behave in a similar manner at a microscopic level in spite of their distinct ionic radii. This is an interesting finding for extending Li‐ion and Li‐air technologies to their potentially cheaper Na‐based counterparts.     

A High‐Voltage and Ultralong‐Life Sodium Full Cell for Stationary Energy Storage

Recently, there has been great interest in developing advanced sodium‐ion batteries for large‐scale application. Most efforts have concentrated on the search for high‐performance electrode materials only in sodium half‐cells. Research on sodium full cells for practical application has encountered many problems, such as insufficient cycles with rapid capacity decay, low safety, and low operating voltage. Herein, we present a layered P2‐Na_0.66Ni_0.17Co_0.17Ti_0.66O₂, as both an anode (ca. 0.69 V versus Na⁺/Na) and as a high‐voltage cathode (ca. 3.74 V versus Na⁺/Na). The full cell based on this bipolar electrode exhibits well‐defined voltage plateaus near 3.10 V, which is the highest average voltage in the symmetric cells. It also shows the longest cycle life (75.9 % capacity retention after 1000 cycles) in all sodium full cells, a usable capacity of 92 mAh g^?1, and superior rate capability (65 mAh g^?1 at a high rate of 2C).     

Flexible Aqueous Lithium‐Ion Battery with High Safety and Large Volumetric Energy Density

A flexible and wearable aqueous lithium‐ion battery is introduced based on spinel Li_1.1Mn₂O₄ cathode and a carbon‐coated NASICON‐type LiTi₂(PO₄)₃ anode (NASICON=sodium‐ion super ionic conductor). Energy densities of 63 Wh kg^?1 or 124 mWh cm^?3 and power densities of 3 275 W kg^?1 or 11.1 W cm^?3 can be obtained, which are seven times larger than the largest reported till now. The full cell can keep its capacity without significant loss under different bending states, which shows excellent flexibility. Furthermore, two such flexible cells in series with an operation voltage of 4 V can be compatible with current nonaqueous Li‐ion batteries. Therefore, such a flexible cell can potentially be put into practical applications for wearable electronics. In addition, a self‐chargeable unit is realized by integrating a single flexible aqueous Li‐ion battery with a commercial flexible solar cell, which may facilitate the long‐time outdoor operation of flexible and wearable electronic devices.     

MoS2 Nanoflowers with Expanded Interlayers as High‐Performance Anodes for Sodium‐Ion Batteries

MoS₂ nanoflowers with expanded interlayer spacing of the (002) plane were synthesized and used as high‐performance anode in Na‐ion batteries. By controlling the cut‐off voltage to the range of 0.4–3 V, an intercalation mechanism rather than a conversion reaction is taking place. The MoS₂ nanoflower electrode shows high discharge capacities of 350 mAh g^?1 at 0.05 A g^?1, 300 mAh g^?1 at 1 A g^?1, and 195 mAh g^?1 at 10 A g^?1. An initial capacity increase with cycling is caused by peeling off MoS₂ layers, which produces more active sites for Na⁺ storage. The stripping of MoS₂ layers occurring in charge/discharge cycling contributes to the enhanced kinetics and low energy barrier for the intercalation of Na⁺ ions. The electrochemical reaction is mainly controlled by the capacitive process, which facilitates the high‐rate capability. Therefore, MoS₂ nanoflowers with expanded interlayers hold promise for rechargeable Na‐ion batteries.     

A Low‐Cost and Environmentally Friendly Mixed Polyanionic Cathode for Sodium‐Ion Storage

Sodium‐ion batteries (NIBs) are the most promising alternatives to lithium‐ion batteries in the development of renewable energy sources. The advancement of NIBs depends on the exploration of new electrode materials and fundamental understanding of working mechanisms. Herein, via experimental and simulation methods, we develop a mixed polyanionic compound, Na₂Fe(C₂O₄)SO₄?H₂O, as a cathode for NIBs. Thanks to its rigid three dimensional framework and the combined inductive effects from oxalate and sulfate, it delivered reversible Na insertion/desertion at average discharging voltages of 3.5 and 3.1 V for 500 cycles with Coulombic efficiencies of ca. 99 %. In situ synchrotron X‐ray measurements and DFT calculations demonstrate the Fe²⁺/Fe³⁺ redox reactions contribute to electron compensation during Na⁺ desertion/insertion. The study suggests mixed polyanionic frameworks may provide promising materials for Na ion storage with the merits of low cost and environmental friendliness.     

Advanced High‐Voltage Aqueous Lithium‐Ion Battery Enabled by “Water‐in‐Bisalt” Electrolyte

A new super‐concentrated aqueous electrolyte is proposed by introducing a second lithium salt. The resultant ultra‐high concentration of 28 m led to more effective formation of a protective interphase on the anode along with further suppression of water activities at both anode and cathode surfaces. The improved electrochemical stability allows the use of TiO₂ as the anode material, and a 2.5 V aqueous Li‐ion cell based on LiMn₂O₄ and carbon‐coated TiO₂ delivered the unprecedented energy density of 100 Wh kg^?1 for rechargeable aqueous Li‐ion cells, along with excellent cycling stability and high coulombic efficiency. It has been demonstrated that the introduction of a second salts into the “water‐in‐salt” electrolyte further pushed the energy densities of aqueous Li‐ion cells closer to those of the state‐of‐the‐art Li‐ion batteries.     

Development and Investigation of a NASICON‐Type High‐Voltage Cathode Material for High‐Power Sodium‐Ion Batteries

Herein, we introduce a 4.0 V class high‐voltage cathode material with a newly recognized sodium superionic conductor (NASICON)‐type structure with cubic symmetry (space group P2₁3), Na₃V(PO₃)₃N. We synthesize an N‐doped graphene oxide‐wrapped Na₃V(PO₃)₃N composite with a uniform carbon coating layer, which shows excellent rate performance and outstanding cycling stability. Its air/water stability and all‐climate performance were carefully investigated. A near‐zero volume change (ca. 0.40 %) was observed for the first time based on in situ synchrotron X‐ray diffraction, and the in situ X‐ray absorption spectra revealed the V^3.2+/V^4.2+ redox reaction with high reversibility. Its 3D sodium diffusion pathways were demonstrated with distinctive low energy barriers. Our results indicate that this high‐voltage NASICON‐type Na₃V(PO₃)₃N composite is a competitive cathode material for sodium‐ion batteries and will receive more attention and studies in the future.