Electrochemical Determination of Citalopram by Adsorptive Stripping Voltammetry–Determination in Pharmaceutical Products

Abstract

The electrochemical behavior of citalopram was studied by square‐wave and square‐wave adsorptive‐stripping voltammetry (SWAdSV). Citalopram can be reduced and accumulated at a mercury drop electrode, with a maximum peak current intensity being obtained at a potential of approximately ?1.25 V vs. AgCl/Ag, in an aqueous electrolyte solution of pH 12. A SWAdSV method has been developed for the determination of citalopram in pharmaceutical preparations. The method shows a linear range between 1.0×10^?7 and 2.0×10^?6 mol L^?1 with a limit of detection of 5×10^?8 mol L^?1 for an accumulation time of 30 s. The precision of the method was evaluated by assessing the repeatability and intermediate precision, achieving good relative standard deviations in all cases (≤2.3%). The proposed method was applied to the determination of citalopram in five pharmaceutical products and the results obtained are in good agreement with the labeled values.     

A Novel Strategy for Quantifying Clopidogrel Using Square‐wave Voltammetry and a Boron‐doped Diamond Film

The voltammetric behavior of clopidogrel bisulfate (CLO), an antiplatelet agent, was investigated for the first time in the literature on a cathodically pretreated boron‐doped diamond electrode (CP‐BDDE) using cyclic (CV) and square‐wave voltammetry (SWV). It was observed an anodic peak for CLO, suitable for analytical purposes, at about 1.15 V (vs. Ag/AgCl (3.0 mol L^?1 KCl)) by CV in Britton‐Robinson buffer solution (pH 5.0). On the physical‐chemical characterization of the interface phenomena, it was proved that electrode reaction of the analyte was controlled by a diffusion process. At optimized square‐wave parameters (pulse amplitude of 60 mV, frequency of 30 Hz and scan increment of 3 mV), the obtained analytical curve was linear for the CLO concentration range from 0.60 to 60.0 μmol L^?1, with a detection limit of 0.60 μmol L^?1. The simple, rapid and greener analytical method, based on CP‐BDDE electrochemical sensor, was successfully applied in real samples (pharmaceuticals and urine).     

Adsorptive Square‐Wave Voltammetry for the Analysis and Speciation of Complexes of Cd(II)‐Ferron

The theory of adsorptive stripping square‐wave voltammetry (SWV) for relatively low ligand concentrations is employed to determine the reduction mechanism of Cd(II)‐ferron complexes accumulated on a static mercury drop electrode at different pH values. The electrochemical behavior of ferron molecules indicated that the adsorptive concentration of Cd(II) is possible in solutions with 3.5<pH<11, providing a wide pH range where the interference of other ligands present in real samples would be not so critical. Cyclic voltammetry experiments were also performed for the purpose of comparison. Fitting between experimental and theoretical square‐wave voltammograms shows that the prevailing species at the reaction layer coincide with the equilibrium bulk distribution. The simulation procedure indicated that the electrochemical rate constants of Cd(II)‐ferron complexes varied from (6±1) s^?1 to (0.17±0.01) s^?1 for solutions analyzed at pH 3.9 and 10.8, respectively. Changes at the surface concentrations are discussed considering the ligand to complex ratios at the electrode surface and at the solution bulk. From this analysis it is possible to infer that the oxidized metal species are produced in the electrolytic solution instead of on the electrode surface.     

Electrocatalytic oxidation and the mechanism of dopamine on a MWNT-modified glassy carbon electrode

The electrochemical behavior of dopamine (DA) at a MWNTs-modified glassy carbon electrode was investigated by cyclic voltammetry (CV), square wave voltammetry (SWV). The MWNTs modified electrode exhibited marked promotion of the electrochemical reaction of DA in different environments. Under optimum conditions, the peak currents of SWV of DA were increased linearly with incremental concentration of DA in the range from 5 × 10^?7 to 1 × 10^?5 mol L^?1. The limit of detection is 3 × 10^?7 mol L^?1.     

Adsorptive Stripping Voltammetric Determination of Trace Level Ricin in Castor Seeds Using a Boron‐doped Diamond Electrode

Ricin, (Ricinus communis agglutinin, RCA) is one of the most poisonous of naturally occurring substances and has great potential for bioterrorism because no antidote exists. Fast detection at low concentrations is a challenge, and vital to the development of proper countermeasures. In this study, a square wave adsorptive stripping voltammetric (SWAdSV) method for determining RCA using a cathodically polarized boron‐doped diamond (BDD) electrode is presented. An irreversible electrochemical RCA oxidation peak was identified on the BDD electrode by different voltammetric techniques using both direct and adsorptive stripping modes. An adsorption‐controlled (slope log Ip vs log v of 0.80) pH‐dependent process was observed. For values of 1.0≤pH≤9.0, the numbers of protons and electrons associated with the oxidation reaction were estimated (ca. 1.0) by differential pulse voltammetry. The RCA oxidation step may correspond to the oxidation of tryptophan amino acid residues, and occurs in a complex mechanism. The excellent analytical performance of the cathodically polarized BDD electrode in combination with the stripping mode ramp was verified with RCA by using a short deposition time in an open circuit potential (120 s). Under optimized analysis conditions, a linear response in the range of (3.3–94.0)×10⁻⁹ mol L⁻¹ (r²=0.9944) and a limit of detection of 6.2×10⁻¹⁰ mol L⁻¹ were estimated. This LOD is lower than several methods found in the literature. For example, it is 168 times lower than that obtained by using square wave voltammetric with a glassy carbon electrode. Moreover, an even lower LOD might be achieved by using the SWAdSV method with a higher pre‐concentration time. In addition, trace levels of RCA were successfully determined in different castor seed cultivars with an overall average recovery from 99.2±1.6 % for the three different RCA‐A concentration levels. The high accuracy of the analytical data highlights the use of the proposed method for determining RCA in other samples.     

A New and Cost Effective Approach for Simultaneous Voltammetric Analysis of two Related Benzimidazole Drugs and their Determination in Biological Fluids

A polymerized film of eriochrome black T (EBT) was prepared on the surface of pencil graphite electrode in alkaline solution by cyclic voltammetry. The redox response of the poly (EBT) film at the electrode appeared in a couple of redox peak in 0.1 M sodium hydroxide. The poly (EBT) film‐coated electrode exhibited excellent electrocatalytic activity towards the oxidation of rabeprazole sodium (RAB sodium) and domperidone (DOM) in Britton‐Robinson buffer (pH 4.0). The polymer film modified electrode conspicuously enhanced the redox currents of the cited mixture and could sensitively and separately determine them. Both cyclic voltammetry (CV) and square wave adsorptive stripping voltammetric (SWAdSV) methods were utilized to determine this mixture. The linearity of CV ranged from 4.1‐120 μM and 5.2‐90 μM for RAB sodium and DOM, respectively while SWAdSV was 7.5‐80×10⁻⁷M and 5–70×10⁻⁷M for RAB sodium and DOM, respectively. With good selectivity and sensitivity, the present method provides a simple method for selective detection of RAB sodium and DOM binary mixture in synthetic mixtures and biological fluids.     

Determination of Blasticidin S in Spiked Rice Using SW Voltammetry with a Renewable Silver Amalgam Film Electrode

Blasticidin S (BS) was determined in spiked rice samples by square wave voltammetry (SWV) and square wave stripping voltammetry (SWSV) using a cyclic renewable silver amalgam film electrode (Hg(Ag)FE). It was found that the compound can act as an electrocatalyst. In Britton? Robinson buffer at pH 7.0 a signal connected with the hydrogen evolution reaction was detected at ?1.2 V versus Ag/AgCl. Validation of the method was carried out. The detection and quantification limits were found to be 2.13×10^?8 mol L^?1; 7.10×10^?8 mol L^?1 for SWV and 2.65×10^?9 mol L^?1; 8.85×10^?9 mol L^?1 for SWSV, respectively.     

Sensitive Voltammetric Determination of Bisphenol A Based on a Glassy Carbon Electrode Modified with Copper Oxide‐Zinc Oxide Decorated on Graphene Oxide

A highly sensitive and selective chemical sensor was prepared based on metallic copper‐copper oxides and zinc oxide decorated graphene oxide modified glassy carbon electrode (Cu?Zn/GO/GCE) through an easily electrochemical method for the quantification of bisphenol A (BPA). The composite electrode was characterized via scanning electron microscopy (SEM), X‐Ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The electrochemical behavior of BPA in Britton‐Robinson (BR) buffer solution (pH 7.1) was examined using cyclic voltammetry (CV). Under optimized conditions, the square wave voltammetry (SWV) response of Cu?Zn/GO/GCE towards BPA indicates two linear relationships within concentrations (3.0 nmol L^?1?0.1 μmol L^?1 and 0.35 μmol L^?1?20.0 μmol L^?) and has a low detection limit (0.88 nmol L^?1). The proposed electrochemical sensor based on Cu?Zn/GO/GCE is both time and cost effective, has good reproducibility, high selectivity as well as stability for BPA determination. The developed composite electrode was used to detect BPA in various samples including baby feeding bottle, pacifier, water bottle and food storage container and satisfactory results were obtained with high recoveries.     

An electroanalytical study of the drug proflavine

A square wave adsorptive stripping voltammetric (SWAdSV) method was developed for the determination of proflavine. The electrochemical behaviour of proflavine was investigated by cyclic (CV) and square wave voltammetry (SWV) at the hanging mercury drop electrode (HMDE) and carbon paste electrode (CPE). Different parameters were tested to optimize the conditions of the determination. Better results were obtained by square wave voltammetry using CPE where two oxidation and a reduction peak, appeared, at 0.19, 0.94 and 0.20 V, respectively. The peak at 0.19 V is quasi-reversible and deposition dependent. Linearity was observed in the range of (0.2–23.4) × 10⁻⁸ M (r = 0.998) during the anodic scan and in the range of (1.17–117) × 10⁻⁸ M (r = 0.999) during the cathodic scan. The second peak at 0.94 V is irreversible and deposition independent. The linearity of this peak was observed in the range of (1.29–11.7) × 10⁻⁸ M (r = 0.998). The method was applied to the analysis of bovine serum and gave satisfactory results. Correspondence: S. Th. Girousi, Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University, Thessaloniki 54124, Greece     

Voltammetric Characterisation of Anticancer Drug Irinotecan

Electrochemical reduction of irinotecan was investigated on a static mercury drop electrode using square‐wave voltammetry. The mechanism of irinotecan electroreduction is a complex, pH‐dependent, quasireversible process and includes the transfer of two electrons and two protons. In acidic medium, the first electron transfer reaction is followed by the chemical reaction, and the product of this chemical reaction undergoes further electrochemical reduction at more negative potentials. Both irinotecan and the product of its reduction adsorb on the mercury electrode surface. Based on the adsorptive character of irinotecan, a new adsorptive stripping square‐wave voltammetric method for its electroanalytical determination has been proposed. The voltammetric response could be used to determine irinotecan in the concentration range from 1×10⁻⁷ mol/L to 1.5×10⁻⁶ mol/L and from 5×10⁻⁹ mol/L to 1.2×10⁻⁷ mol/L, if the accumulation time is 20 s and 300 s, respectively. The calculated limit of detection for irinotecan was found to be 8.7×10⁻⁹ mol/L (if t_acc=300 s).     

Catalytic Adsorptive Stripping Voltammetry of Molybdenum: Redox Kinetic Measurements

The electrode mechanism of Mo(VI) reduction was studied under catalytic adsorptive stripping mode by means of square‐wave voltammetry (SWV). Mo(VI) creates a stable surface active complex with mandelic acid. The electrode reaction of Mo(VI)‐mandelic acid system undergoes as one‐electron reduction, exhibiting properties of a surface electrode process. In the presence of chlorate, bromate, and hydrogen peroxide, the electrode reaction is transposed into a catalytic mechanism. The experimental results are compared with the recent theory for surface catalytic reaction, enabling qualitative characterization of the electrode mechanism in the presence of different catalytic agents. Utilizing both the method of “split SW peaks” and “quasireversible maximum” the standard redox rate constant of Mo(VI)‐mandelic acid system was estimates as k_s=150±5 s^?1. By fitting the experimental and theoretical results, the following catalytic rate constants have been estimated: (8.0±0.5)×10⁴ mol^?1 dm³ s^?1, (1.0±0.1)×10⁵ mol^?1 dm³ s^?1, and (3.2±0.1)×10⁶ mol^?1 dm³ s^?1, for hydrogen peroxide, chlorate, and bromate, respectively.     

Determination of Rutin in Green Tea Infusions Using Square‐Wave Voltammetry with a Rigid Carbon‐Polyurethane Composite Electrode

This paper presents a comparative study on the electrochemical behavior of the flavonoid rutin on a rigid carbon‐polyurethane composite electrode and on a glassy carbon electrode. The electrochemical oxidation reaction of rutin was found to be quasireversible and affected by adsorption on the electrode surface. A square‐wave voltammetric method was developed for determination of rutin in green tea infusion samples using the RCPE electrode and data treatment by a deconvolution procedure. The detection limit achieved in buffered solutions was 7.1×10^?9 mol L^?1 using the RCPE and 1.7×10^?8 mol L^?1 using the GC electrode the average reproducibility for five determinations being 3.5%.     

Electrochemical Determination of Some Organic Pollutants Using Wall‐Jet Electrode

Determination of organic pollutants in trace level in a flow stream was developed using a wall‐jet electrode system and square‐wave stripping principles. Pesticides such as endosulfan, isoproturon and carbendazim, o‐chlorophenol and a benzidine bisazo dye, direct orange 8 were chosen for this study. The optimum conditions for adsorptive square‐wave stripping voltammetry were arrived at and the peak current responses of analyte were correlated over flow rate. Calibration plots were obtained by correlating the peak currents with concentration under optimum conditions. The best determination range, 1×10^?4 to 4.0 mg/mL for endosulfan and 1×10^?4 to 1.5 mg/mL for the remaining pollutants in a flowing stream was obtained with adsorptive square‐wave stripping technique.     

Ex Situ Prepared Antimony Film Electrode for Electrochemical Stripping Measurement of Heavy Metal Ions

The antimony film electrode (SbFE) was prepared ex situ for anodic and adsorptive stripping voltammetric measurement of selected heavy metal ions. The electrode revealed good linearity for Cd(II) and Pb(II) in a nondeaerated solution of 0.01 M HCl in the examined concentration range from 25 to 80 μg L^?1 with limits of detection of 1.1 μg L^?1 for Cd(II) and 0.3 μg L^?1 for Pb(II) and an excellent reproducibility. The preplated SbFE was also preliminary tested for measuring low levels of Ni(II) using adsorptive stripping voltammetry exhibiting good linearity and sensitivity in combination with only a 30 s deposition step.     

Application of a Carbon Paste Electrode Modified with a Schiff Base Ligand to Mercury Speciation in Water

A carbon paste electrode, modified with benzylbisthiosemicarbazone is used for mercury speciation in water samples. Mercury ion is selectively accumulated on the electrode surface at open circuit and its analysis was performed by cyclic voltammetry or square‐wave voltammetry (SWV). A detection limit of 8 μg L^?1 (3σ) was found for 15 min of accumulation using SWV as measurement technique. The effect of several metallic ions and organic substances on voltammetric signal is examined. For speciation purposes, a ligand competition methodology between ligands in solution and electrode is used. Model mercury complexes are characterized as a function of their dissociation kinetics. The method was applied to mercury speciation in water samples from the Jarama River in Madrid.     

Simultaneous Electrochemical Determination of Hydroquinone and Bisphenol A using a Carbon Paste Electrode Modified with Silver Nanoparticles

In this paper, a rapid and sensitive modified electrode for the simultaneous determination of hydroquinone (HQ) and bisphenol A (BPA) is proposed. The simultaneous determination of these two compounds is extremely important since they can coexist in the same sample and are very harmful to plants, animals and the environment in general. A carbon paste electrode (CPE) was modified with silver nanoparticles (nAg) and polyvinylpyrrolidone (PVP). The PVP was used as a reducing and stabilizing agent of nAg from silver nitrate in aqueous media. The nAg‐PVP composite obtained was characterized by transmission electron microscopy and UV‐vis spectroscopy. The electrochemical behavior of HQ and BPA at the nAg‐PVP/CPE was investigated in 0.1 mol L⁻¹ B−R buffer (pH 6.0) using cyclic voltammetry (CV) and square wave voltammetry (SWV). The results indicate that the electrochemical responses are improved significantly with the use of the modified electrode. The calibration curves obtained by SWV, under the optimized conditions, showed linear ranges of 0.09–2.00 μmol L⁻¹ for HQ (limit of detection 0.088 μmol L⁻¹) and 0.04–1.00 μmol L⁻¹ for BPA (limit of detection 0.025 μmol L⁻¹). The modified electrode was successfully applied in the analysis of water samples and the results were comparable to those obtained using UV‐vis spectroscopy.     

Voltammetric Behavior of Mifepristone (RU‐486) Using Square‐Wave and Adsortive Stripping‐Wave Techniques. Determination in Urine Samples

The behavior of Mifepristone (RU‐486) was studied by square‐wave technique, leading to two methods for its determination in aqueous samples and urine samples at pH 2. The application of the square‐wave (SW) without the adsorptive accumulation and stripping voltammetric (AdSV) show the maximum response at ?0.896 V using an accumulation potential of ?0.5 V. The effect of experimental parameters that affect this determination are discussed. For the stripping technique, Mifepristone proved to be more sensitive, yielding signals four times larger than those obtained by applying a square‐wave scan without the previous accumulation. The calibration plot to determine Mifepristone was linear in the range 2.4×10^?8 and 5.4×10^?7 M by stripping mode with an accumulation time t_acc of 30 s. The relative standard deviation obtained for concentration levels of Mifepristone as low as 2.0×10^?7 M with square‐wave was 1.17% (n=10) and with stripping square‐wave 2.02% (n=10) in the same day. The two proposed methods (SW and SWAdSV) were applied to the determination of Mifepristone in urine.     

The Use of the Bismuth Film Electrode for the Anodic Stripping Voltammetric Determination of Tin

Bismuth coated glassy carbon electrodes have been applied to the square‐wave anodic stripping voltammetry (SWASV) of trace concentrations of tin. Optimization of Bismuth Film Electrode (BFE) performance was conducted after initial comparison with the more traditional mercury electrode. Simultaneous deposition of tin and bismuth at ?1.3 V for 2 minutes in a supporting electrolyte of 2.5 M sodium bromide utilizing a square‐wave stripping step, allowed analysis of tin at the μg L^?1 level. Parameters, such as deposition potential and time, bismuth concentration, square‐waveform settings including amplitude, step height and frequency were studied and optimized. The dependence of stripping current on deposition time indicates that using longer deposition time should facilitate sub μg L^?1 analysis. Tin was analyzed simultaneously with cadmium and either indium or thallium; Where as lead and copper were not resolved from the stripping peaks of tin and bismuth respectively. Finally, the method was applied to the analysis of tin in fruit juice.     

Electroanalytical Determination of Cd(II) and Pb(II) in Bivalve Mollusks using Electrochemically Reduced Graphene Oxide‐based Electrode

An electrochemical sensor for the simultaneous determination of Cd(II) and Pb(II) by square wave anodic stripping voltammetry (SWASV) in bivalve mollusks using a glassy carbon electrode modified with electrochemically reduced graphene oxide has been developed. The modified surface was characterized by cyclic voltammetry, high resolution scanning electron microscopy (HR‐SEM), and Raman spectroscopy. The optimum conditions were optimized and a linear range was observed from 15–105 μg L^?1 with a limits of detection of 15 μg L^?1 for Cd(II) and Pb(II). The methodology was validated and applied in different samples of commercial bivalve mollusks with satisfactory results. The high conductivity and greater surface area of the modifying agent improves the preconcentration capacity of the electrochemical sensor, allowing to develop a simple, rapid and sensitive analysis in the detection of lead and cadmium in marine resources.     

Surfactant-intercalated smectite modified electrode: sensitive electrochemical detection of methyl orange dye

This work describes the use of organosmectite modified electrode to evaluate the electrochemical behaviour and to develop an electroanalytical procedure for the determination of methyl orange (MO) dye in natural water. Organosmectites were prepared by intercalation of hexadecyltrimethylammonium cations at various ratios into the interlayer of smectite. The synthesised organosmectites were characterised by various physicochemical techniques such as Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. An amperometric sensor based on organosmectite as electrode modifier for MO sensing purposes was then evaluated by means of clay-film modified electrode using square wave voltammetry (SWV). The electrochemical procedure for MO analysis by stripping voltammetry involves two successive steps: accumulation of MO at open circuit conditions followed by a voltammetric detection in a same medium by the SWV technique. The peak current obtained (after 5 min preconcentration of 15 µmol L^?1 MO solution) on a glassy carbon electrode coated by a thin film of the modified clay was more than 2.5 times higher than that exhibited by the same substrate covered by a film of the pristine clay. Under optimised conditions, a linear calibration curve for MO was obtained in the concentration range from 0.1 to 1.6 µmol L^?1, leading to a detection limit of 4 × 10^?8 mol L^?1 (signal-to-noise ratio equal to 3). The interfering effect of various inorganic and organic ions likely to influence the stripping determination of the MO was also examined. To further validate application of this sensor, the proposed method was successfully used to the determination of MO in natural water with satisfactory results.