Synchronous Electrocatalytic Design of Architectural and Electronic Structure Based on Bifunctional LDH-Co3O4/NF toward Water Splitting

The rational design of highly efficient bifunctional electrocatalysts for water splitting is extremely urgent for application in sustainable energy conversion processes to alleviate the energy crisis and environmental pollution. In this work, through simple deposition of layered double hydroxides (LDH) on Co₃O₄/NF (NF=nickel foam) nanosheets arrays, hierarchical Co³⁺-rich materials based on LDH-Co₃O₄/NF are prepared as highly active and stable electrocatalysts for water splitting. The NiFe-LDH-Co₃O₄/NF demonstrates excellent electrochemical activity with an overpotential of 214 mV for the OER and an overpotential of 162 mV for the HER at 10 mA cm⁻². Such a performance is attributed to the optimized electronic states with a high concentration of Co³⁺, which improves the intrinsic activity, and the sheet-on-sheet hierarchical structure, which increases the number of active sites. The unique synchronous design of both the architectural and electronic structure of nanomaterials can simultaneously accelerate the reaction kinetics and provide a more convenient charge transfer path. Therefore, the strategy reported herein may open a new pathway for the design of excellent electrocatalysts for water splitting.     

Controlled Synthesis of 3D Flower‐like Ni2P Composed of Mesoporous Nanoplates for Overall Water Splitting

Developing efficient non‐noble metal and earth‐abundant electrocatalysts with tunable microstructures for overall water splitting is critical to promote clean energy technologies for a hydrogen economy. Herein, novel three‐dimensional (3D) flower‐like Ni₂P composed of mesoporous nanoplates with controllable morphology and high surface area was prepared by a hydrothermal method and low‐temperature phosphidation as efficient electrocatalysts for the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Compared with the urchin‐like Ni_x P_y , the 3D flower‐like Ni₂P with a diameter of 5 μm presented an efficient and stable catalytic performance in 0.5 m H₂SO₄, with a small Tafel slope of 79 mV dec⁻¹ and an overpotential of about 240 mV at a current density of 10 mA cm⁻² with a mass loading density of 0.283 mg cm⁻². In addition, the catalyst also exhibited a remarkable performance for the OER in 1.0 m KOH electrolyte, with an overpotential of 320 mV to reach a current density of 10 mA cm⁻² and a small Tafel slope of 72 mV dec⁻¹. The excellent catalytic performance of the as‐prepared Ni₂P may be ascribed to its novel 3D morphology with unique mesoporous structure.     

Interface Engineering of MoS2/Ni3S2 Heterostructures for Highly Enhanced Electrochemical Overall‐Water‐Splitting Activity

To achieve sustainable production of H₂ fuel through water splitting, low‐cost electrocatalysts for the hydrogen‐evolution reaction (HER) and the oxygen‐evolution reaction (OER) are required to replace Pt and IrO₂ catalysts. Herein, for the first time, we present the interface engineering of novel MoS₂/Ni₃S₂ heterostructures, in which abundant interfaces are formed. For OER, such MoS₂/Ni₃S₂ heterostructures show an extremely low overpotential of ca. 218 mV at 10 mA cm^?2, which is superior to that of the state‐of‐the‐art OER electrocatalysts. Using MoS₂/Ni₃S₂ heterostructures as bifunctional electrocatalysts, an alkali electrolyzer delivers a current density of 10 mA cm^?2 at a very low cell voltage of ca. 1.56 V. In combination with DFT calculations, this study demonstrates that the constructed interfaces synergistically favor the chemisorption of hydrogen and oxygen‐containing intermediates, thus accelerating the overall electrochemical water splitting.     

Heterostructured Inter‐Doped Ruthenium–Cobalt Oxide Hollow Nanosheet Arrays for Highly Efficient Overall Water Splitting

The development of transition‐metal‐oxides (TMOs)‐based bifunctional catalysts toward efficient overall water splitting through delicate control of composition and structure is a challenging task. Herein, the rational design and controllable fabrication of unique heterostructured inter‐doped ruthenium–cobalt oxide [(Ru–Co)O_x] hollow nanosheet arrays on carbon cloth is reported. Benefiting from the desirable compositional and structural advantages of more exposed active sites, optimized electronic structure, and interfacial synergy effect, the (Ru–Co)O_x nanoarrays exhibited outstanding performance as a bifunctional catalyst. Particularly, the catalyst showed a remarkable hydrogen evolution reaction (HER) activity with an overpotential of 44.1 mV at 10 mA cm^?2 and a small Tafel slope of 23.5 mV dec^?1, as well as an excellent oxygen evolution reaction (OER) activity with an overpotential of 171.2 mV at 10 mA cm^?2. As a result, a very low cell voltage of 1.488 V was needed at 10 mA cm^?2 for alkaline overall water splitting.     

High Valence State Sites as Favorable Reductive Centers for High-Current-Density Water Splitting

Electrochemical water splitting is a promising approach for producing sustainable and clean hydrogen. Typically, high valence state sites are favorable for oxidation evolution reaction (OER), while low valence states can facilitate hydrogen evolution reaction (HER). However, here we proposed a high valence state of Co³⁺ in Ni_9.5Co_0.5−S−FeO_x hybrid as the favorable center for efficient and stable HER, while structural analogues with low chemical states showed much worse performance. As a result, the Ni_9.5Co_0.5−S−FeO_x catalyst could drive alkaline HER with an ultra-low overpotential of 22 mV for 10 mA cm⁻², and 175 mV for 1000 mA cm⁻² at the industrial temperature of 60 °C, with an excellent stability over 300 h. Moreover, this material could work for both OER and HER, with a low cell voltage being 1.730 V to achieve 1000 mA cm⁻² for overall water splitting at 60 °C. X-ray absorption spectroscopy (XAS) clearly identified the high valence Co³⁺ sites, while in situ XAS during HER and theoretical calculations revealed the favorable electron capture at Co³⁺ and suitable H adsorption/desorption energy around Co³⁺, which could accelerate the HER. The understanding of high valence states to drive reductive reactions may pave the way for the rational design of energy-related catalysts.     

Bimetallic cobalt-nickel coordination polymer electrocatalysts for enhancing oxygen evolution reaction

Coordination polymers（CPs） have great potential to be used in electrocatalysis owing to their designable compositions and structures. It is highly challenging to apply CPs as electrocatalysts for oxygen evolution reaction（OER） on account of insufficient catalytic efficiency and relatively poor stability of current electrocatalysts. Herein, through a mixed-metal strategy, one-dimensional Co_xNi_1-x-HIPA with dual active sites was synthesized and studied for OER electrocatalyst...     

Flower-like NiCo2S4/NiFeP/NF composite material as an effective electrocatalyst with high overall water splitting performance

Rational design and building of high efficiency, secure and inexpensive electrocatalyst is a pressing demand and performance to promote sustainable improvement of hydrogen energy. The bifunctional electrocatalysts for oxygen evolution reaction (OER) and hydrogen evolution response (HER) with high catalytic performance and steadiness in the equal electrolyte are extra treasured and meaningful. Herein, a unique three-dimensional (3D) structure electrocatalyst for NiCo₂S₄ growing on the flower-like NiFeP was designed and synthesized in this study. The results show that the flower-like NiCo₂S₄/NiFeP/NF composite electrocatalyst has large specific surface area, appropriate electrical conductivity, and greater lively websites uncovered in the three-dimensional structure, and affords extraordinary electrocatalytic overall performance for the ordinary water splitting. In alkaline solution, the OER and HER overpotentials of NiCo₂S₄/NiFeP/NF only need 293 mV and 205 mV overpotential to provide the current densities of 100 mA/cm² and 50 mA/cm², respectively. This high electrocatalytic activity exceeds the catalytic activity of most nickel-iron based electrocatalysts for OER and HER process. Accordingly, the optimized NiCo₂S₄/NiFeP/NF sample has higher stability (24 h) at 1.560 and 10 mA/cm², which extensively speeds up the overall water splitting process. In view of the above performance, this work offers a fine approach for the further improvement of low fee and excessive effectivity electrocatalyst.     

Improving the Electrocatalytic Activity of a Nickel-Organic Framework toward the Oxygen Evolution Reaction through Vanadium Doping

Metal-organic frameworks (MOFs) have been considered as potential oxygen evolution reaction (OER) electrocatalysts owning to their ultra-thin structure, adjustable composition, high surface area, and high porosity. Here, we designed and fabricated a vanadium-doped nickel organic framework (V_1−x−Ni_xMOF) system by using a facile two-step solvothermal method on nickel foam (NF). The doping of vanadium remarkably elevates the OER activity of V_1−x−Ni_xMOF, thus demonstrating better performance than the corresponding single metallic Ni-MOF, NiV-MOF and RuO₂ catalysts at high current density (>400 mA cm⁻²). V_0.09−Ni_0.91MOF/NF provides a low overpotential of 235 mV and a small Tafel slope of 30.3 mV dec⁻¹ at a current density of 10 mA cm⁻². More importantly, a water-splitting device assembled with Pt/C/NF and V_0.09−Ni_0.91MOF/NF as cathode and anode yielded a cell voltage of 1.96 V@1000 mA cm⁻², thereby outperforming the-state-of-the-art RuO₂⁽⁺⁾||Pt/C⁽⁻⁾. Our work sheds new insight on preparing stable, efficient OER electrocatalysts and a promising method for designing various MOF-based materials.     

Carbon Dots Integrated NiCo2O4 Hierarchical Nanoneedle Arrays Supported on Ni Foam as Efficient and Stable Electrode for Hydrogen and Oxygen Evolution Reactions

The production of hydrogen and oxygen via water electrolysis has become a sustainable and encouraging pathway for the establishment of new energy sources. Herein, we report the successful growth of hierarchical NiCo₂O₄‐carbon dots (CDs) nanoneedle arrays supported on nickel foam through a simple and environmentally benign hydrothermal self‐assembly technique. The designed material acts as a binder free electrode and shows bifunctional electrocatalytic activity for both hydrogen evolution reaction (HER) as well as oxygen evolution reaction (OER) in alkaline medium. An electrocatalyst sample with an optimal loading of CDs (25 mg) requires a low overpotential of 146 mV to achieve a current density of 10 mA/cm² for the HER in an alkaline medium, whereas it requires an overpotential of 390 mV to achieve a current density of 50 mA/cm² for the OER in the same alkaline medium. The excellent electrocatalytic activities of the sample with loading of CD can be ascribed due to the presence of large number of exposed active sites offered by CD/NiCo₂O₄ and the enhanced electron transfer processes occurring as a result of hierarchical structure composed of three‐dimensional nickel foam and the NiCo₂O₄?CDs nanoneedle arrays. Thus, the synthesis method introduced in this present work is a facile and cost‐effective approach for the construction of bifunctional electrocatalysts with high reactivity and excellent durability.     

Two-Dimensional NiIr@N-Doped Carbon Nanocomposites Supported on Ni Foam for Electrocatalytic Overall Water Splitting

Electrochemical water splitting can provide a promising avenue for sustainable hydrogen production. Highly efficient electrocatalysts toward the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) are extremely important for the practical application of water splitting technology. Herein, a one-step annealing strategy is reported for the fabrication of a metal–organic framework-derived bifunctional self-supported electrocatalyst, which is composed of two-dimensional N-doped carbon-wrapped Ir-doped Ni nanoparticle composites supported on Ni foam (NiIr@N-C/NF). The resultant NiIr@N-C/NF displays excellent electrocatalytic performance in 1.0 m KOH, with low overpotentials of 32 mV at 10 mA cm⁻² for the HER and 329 mV at 50 mA cm⁻² for the OER. Particularly, the HER-OER bifunctional NiIr@N-C/NF needs only 1.50 V to yield 10 mA cm⁻² for overall water splitting.     

Controlled Synthesis of Cr‐Co0.85Se Nanoarrays for Water Splitting at an Ultralow Cell Voltage of 1.43 V

Water splitting has attracted more and more attention as a promising strategy for the production of clean hydrogen fuel. In this work, a new synthesis strategy was proposed, and Co_0.85Se was synthesized on nickel foam as the main matrix. The doping of appropriate Cr amount into the target of Co_0.85Se and the Cr‐Co_0.85Se resulted in an excellent electrochemical performance. The doping of Cr introduces Cr³⁺ ions which substitute Co²⁺ and Co³⁺ ions in Co_0.85Se, so that the lattice parameters of the main matrix were changed. It is worth noting that the Cr0.15‐Co_0.85Se/NF material exhibits an excellent performance in the oxygen evolution reaction (OER) test. When the current density reaches 50 mA cm^?2 for OER, the overpotential is only 240 mV. For the hydrogen evolution reaction (HER) tests, the overpotential is only 117 mV to drive 10 mA cm^?2 of current density. Moreover, when the Cr0.15‐Co_0.85Se/NF material is used as a two‐electrode device for whole water splitting, the required cell voltage is only 1.43 V to reach a current density of 10 mA cm^?2, which is among the lowest values of the published catalysts up to now. In addition, the Cr0.15‐Co_0.85Se/NF catalyst also exhibits excellent stability during a long period of water splitting. The experimental result demonstrates that the change of the lattice structure has an obvious influence on the electrocatalytic activity of the material. When an external electric field is applied, it facilitates the rapid electron transfer rate and enhances the electrocatalytic performance and stability of the material.     

Heterostructured Inter-Doped Ruthenium–Cobalt Oxide Hollow Nanosheet Arrays for Highly Efficient Overall Water Splitting

The development of transition-metal-oxides (TMOs)-based bifunctional catalysts toward efficient overall water splitting through delicate control of composition and structure is a challenging task. Herein, the rational design and controllable fabrication of unique heterostructured inter-doped ruthenium–cobalt oxide [(Ru–Co)O_x] hollow nanosheet arrays on carbon cloth is reported. Benefiting from the desirable compositional and structural advantages of more exposed active sites, optimized electronic structure, and interfacial synergy effect, the (Ru–Co)O_x nanoarrays exhibited outstanding performance as a bifunctional catalyst. Particularly, the catalyst showed a remarkable hydrogen evolution reaction (HER) activity with an overpotential of 44.1 mV at 10 mA cm⁻² and a small Tafel slope of 23.5 mV dec⁻¹, as well as an excellent oxygen evolution reaction (OER) activity with an overpotential of 171.2 mV at 10 mA cm⁻². As a result, a very low cell voltage of 1.488 V was needed at 10 mA cm⁻² for alkaline overall water splitting.     

Imine Gels Based on Ferrocene and Porphyrin and Their Electrocatalytic Property

A series of porphyrin‐based imine gels have been synthesized via dynamic covalent gelation between 5,10,15,20‐tetra(4‐aminophenyl)‐21H,23H‐porphyrin (H₂TAPP) derivatives and various aldehyde compounds. The porphyrin‐ferrocene imine gels based on MTAPP (M=H₂, Ni²⁺, Co²⁺, Pd²⁺ and Zn²⁺) and ferrocene‐1,1′‐dicarbaldehyde (NA) display efficient HER, OER and ORR activities in alkaline media. Among the gels, CoTAPP‐NA shows an HER current density of 10 mA cm^?2 at low overpotential of 470 mV and small Tafel slope of 110 mV decade^?1 in alkaline media. CoTAPP‐NA also exhibits OER catalytic activity with low overpotential (416 mV for 10 mA cm^?2). CoTAPP‐NA shows ability in overall water splitting in alkaline media. In addition, CoTAPP‐NA exhibits onset potential (E_p) of 0.95 V and half‐wave potential (E_1/2) of 0.84 V in 1.0 mol L^?1 KOH solution for oxygen reduction. Moreover, the gel catalyst shows good stability.     

Double Perovskite LaFexNi1−xO3 Nanorods Enable Efficient Oxygen Evolution Electrocatalysis

Perovskite‐based electrocatalysts are one of the most promising materials for oxygen evolution reaction (OER), but their activity and durability are still far from desirable. Herein, we demonstrate that the double perovskite LaFe_xNi_1?xO₃ (LFNO) nanorods (NRs) can be adopted as highly active and stable OER electrocatalysts. The optimized LFNO‐II NRs with Ni/Fe ratio of 8:2 achieve a low overpotential of 302 mV at 10 mA cm^?2 and a small Tafel slope of 50 mV dec^?1, outperforming those of the commercial Ir/C. The LFNO‐II NRs also show high OER stability with slight current decrease after 20 h. The enhanced activity is explained by the improved surface area, tailored electronic structure as well as strong hybridization between O and Ni.     

Heterometallic Feed Ratio-Dominated Oxygen Evolution Activity in Self-Supported Metal-Organic Framework Nanosheet Arrays Electrocatalyst

Developing earth-abundant, highly active and long-term durable electrocatalysts for oxygen evolution reaction (OER) is highly desirable and great challenging for large-scale industrial application of electrochemical water splitting. Herein, in-situ growth of uniform nanosheet arrays on nickel foam (NF) is hydrothermally achieved by varying feed ratios of Fe^III and Ni^II salts. The feed ratio of the two active metals has significantly dominated both the morphological and electronic structures of the resultant electrocatalysts, leading to feed ratio-dependent volcano-type OER activity. The optimized Fe_0.89Ni_0.11-BDC/NF exhibits the best OER performance, affording a low overpotential of 220 mV to drive a current density of 50 mA · cm^–2 with small Tafel slope of 44.8 mV · dec^–1 and long-lasting stability over 20 hours. The synergistic effect from the Fe^III and Ni^II species on both the morphological and electronic structure modulations have dramatically accelerated the reaction kinetics, responsible eventually for the enhanced OER activity. This work provides valuable information for nanostructured MOFs as efficient electrocatalysts.     

Boosting Electrocatalytic Oxygen Evolution over Ce−Co9S8 Core–Shell Nanoneedle Arrays by Electronic and Architectural Dual Engineering

An dual electronic and architectural engineering strategy is a good way to rationally design earth-abundant and highly efficient electrocatalysts of the oxygen evolution reaction (OER) for sustainable hydrogen-based energy devices. Here, a Ce-doped Co₉S₈ core–shell nanoneedle array (Ce−Co₉S₈@CC) supported on a carbon cloth has been designed and developed to accelerate the sluggish kinetics of the OER. Profiting from valance alternative Ce doping, a fine core–shell structure and vertically aligned nanoneedle arrayed architecture, Ce−Co₉S₈@CC integrates modulated electronic structure, highly exposed active sites, and multidimensional mass diffusion channels; together, these afford a favorable catalyzed OER. Ce−Co₉S₈@CC exhibits remarkable performance in the OER in an alkaline medium, where the overpotential requires only 242 mV to deliver a current density of 10 mA cm⁻² for the OER; this is 70 mV superior to that of Ce-free Co₉S₈ catalyst and other counterparts. Good stability and impressive selectivity (nearly 100 % Faradic efficiency) are also demonstrated. When integrated into a two-electrode OER//HER electrolyzer, the as-prepared Ce−Co₉S₈@CC displays a low operation potential of 1.54 V at 10 mA cm⁻² and long-term stability, thus demonstrating great potential for economical water electrolysis.     

Topochemical Synthesis of Two‐Dimensional Transition‐Metal Phosphides Using Phosphorene Templates

Transition‐metal phosphides (TMPs) have emerged as a fascinating class of narrow‐gap semiconductors and electrocatalysts. However, they are intrinsic nonlayered materials that cannot be delaminated into two‐dimensional (2D) sheets. Here, we demonstrate a general bottom‐up topochemical strategy to synthesize a series of 2D TMPs (e.g. Co₂P, Ni₁₂P₅, and Co_xFe_2?xP) by using phosphorene sheets as the phosphorus precursors and 2D templates. Notably, 2D Co₂P is a p‐type semiconductor, with a hole mobility of 20.8 cm² V^?1 s^?1 at 300 K in field‐effect transistors. It also behaves as a promising electrocatalyst for the oxygen evolution reaction (OER), thanks to the charge‐transport modulation and improved surface exposure. In particular, iron‐doped Co₂P (i.e. Co_1.5Fe_0.5P) delivers a low overpotential of only 278 mV at a current density of 10 mA cm^?2 that outperforms the commercial Ir/C benchmark (304 mV).     

Fe‐Doped Ni3C Nanodots in N‐Doped Carbon Nanosheets for Efficient Hydrogen‐Evolution and Oxygen‐Evolution Electrocatalysis

Uniform Ni₃C nanodots dispersed in ultrathin N‐doped carbon nanosheets were successfully prepared by carburization of the two dimensional (2D) nickel cyanide coordination polymer precursors. The Ni₃C based nanosheets have lateral length of about 200 nm and thickness of 10 nm. When doped with Fe, the Ni₃C based nanosheets exhibited outstanding electrocatalytic properties for both the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). For example, 2 at % Fe (atomic percent) doped Ni₃C nanosheets depict a low overpotential (292 mV) and a small Tafel slope (41.3 mV dec⁻¹) for HER in KOH solution. An outstanding OER catalytic property is also achieved with a low overpotential of 275 mV and a small Tafel slope of 62 mV dec⁻¹ in KOH solution. Such nanodot‐incorporated 2D hybrid structures can serve as an efficient bifunctional electrocatalyst for overall water splitting.     

Electrodeposition of Defect-Rich Ternary NiCoFe Layered Double Hydroxides: Fine Modulation of Co3+ for Highly Efficient Oxygen Evolution Reaction

The low-cost, high-abundance and durable layered double hydroxides (LDHs) have been considered as promising electrocatalysts for oxygen evolution reaction (OER). However, the easy agglomeration of lamellar LDHs in the aqueous phase limits their practical applications. Herein, a series of ternary NiCoFe LDHs were successfully fabricated on nickel foam (NF) via a simple electrodeposition method. The as-prepared Ni(Co_0.5Fe_0.5)/NF displayed an unique nanoarray structural feature. It showed an OER overpotential of 209 mV at a current density of 10 mA cm⁻² in alkaline solution, which was superior to most systems reported so far. As evidenced by the XPS and XAFS results, such excellent performance of Ni(Co_0.5Fe_0.5)/NF was attributed to the higher Co³⁺/Co²⁺ ratio and more defects exposed, comparing with Ni(Co_0.5Fe_0.5)-bulk and Ni(Co_0.5Fe_0.5)-mono LDHs prepared by conventional coprecipitation method. Furthermore, the ratio of Co to Fe could significantly tune the Co electronic structure of Ni(Co_xFe_1-x)/NF composites (x=0.25, 0.50 and 0.75) and affect the electrocatalytic activity for OER, in which Ni(Co_0.5Fe_0.5)/NF showed the lowest energy barrier for OER rate-determining step (from O* to OOH*). This work proposes a facile method to develop high-efficiency OER electrocatalysts.     

Manganese-Modulated Cobalt-Based Layered Double Hydroxide Grown on Nickel Foam with 1D–2D–3D Heterostructure for Highly Efficient Oxygen Evolution Reaction and Urea Oxidation Reaction

Hydrogen production by energy-efficient water electrolysis is a green avenue for the development of contemporary society. However, the oxygen evolution reaction (OER) and the urea oxidation reaction (UOR) occurring at the anode are impeded by the sluggish reaction kinetics during the water-splitting process. Consequently, it is promising to develop bifunctional anodic electrocatalysts consisting of nonprecious metals. Herein, a bifunctional CoMn layered double hydroxide (LDH) was grown on nickel foam (NF) with a 1D–2D–3D hierarchical structure for efficient OER and UOR performance in alkaline solution. Owing to the significant synergistic effect of Mn doping and heterostructure engineering, the obtained Co₁Mn₁ LDH/NF exhibits satisfactory OER activity with a low potential of 1.515 V to attain 10 mA cm⁻². Besides, the potential of the Co₁Mn₁ LDH/NF catalyst for UOR at the same current density is only 1.326 V, which is much lower than those of its counterparts and most reported electrocatalysts. An urea electrolytic cell with a Co₁Mn₁ LDH/NF anode and a Pt–C/NF cathode was established, and a low cell voltage of 1.354 V at 10 mA cm⁻² was acquired. The optimized strategy may result in promising candidates for developing a new generation of bifunctional electrocatalysts for clean energy production.