Electrochemical Determination of D‐Glucose Using Nortropine‐N‐oxyl under Physiological Conditions

Nortropine‐N‐oxyl (NNO) was synthesized in a single step from nortropine. The electrocatalytical activity of NNO was evaluated by cyclic voltammetry in pH7.0 phosphate buffer solution. The anodic peak current for ethanol, isopropanol and glucose was enhanced, showing these alcohols were oxidized by electrocatalytic effect of NNO. On the other hand, TEMPO derivative (4‐hydroxy‐2,2,6,6,‐terramethylpiperidine N‐oxyl free radical) could not oxidize the alcohols under the same condition. The electrochemical response of the NNO to glucose was investigated. The anodic peak current increased with an increase in the concentration of glucose. A linear response to the glucose concentration ranging from 0.1 to 10 mM was obtained.     

Polyaniline/Single‐Walled Carbon Nanotubes Composite Based Triglyceride Biosensor

Nanocomposite film comprising of polyaniline (PANI) and single walled carbon nanotubes (SWCNT) has been fabricated onto indium‐tin‐oxide (ITO) coated glass plate using electrophoretic technique. Co‐immobilization of glycerol dehydrogenase (GDH) and lipase (LIP) has been done via N‐ethyl‐N′‐(3‐dimethylaminopropyl) carbodiimide and N‐hydroxysuccinimide chemistry to explore its application for triglyceride (tributyrin) sensing. Response studies have been done using linear sweep voltammetry revealing that LIP‐GDH/PANI‐SWCNT‐TB/ITO bioelectrode can detect tributyrin in the range of 50 to 400 mg dL^?1 with low Michaelis–Menten constant of 1.138 mM, improved response time of 12 s, high sensitivity as 4.28×10^?4 mA mg^?1 dL and storage stability of about 13 weeks.     

Electrochemical Behavior and Electroanalytical Determination of Indole‐3‐Acetic Acid Phytohormone on a Boron‐Doped Diamond Electrode

In this work, a boron‐doped diamond (BDD) electrode was used for the electroanalytical determination of indole‐3‐acetic acid (IAA) phytohormone by square‐wave voltammetry. IAA yielded a well‐defined voltammetric response at +0.93 V (vs. Ag/AgCl) in Britton–Robinson buffer, pH 2.0. The process could be used to determine IAA in the concentration range of 5.0 to 50.0 µM (n=8, r=0.997), with a detection limit of 1.22 µM. The relative standard deviation of ten measurements was 2.09 % for 20.0 µM IAA. As an example, the practical applicability of BDD electrode was tested with the measurement of IAA in some plant seeds.     

Stripping Voltammetry of Mercury(II) with a Chemically Modified Carbon Paste Electrode Containing Silica Gel Functionalized with 2,5‐Dimercapto‐1,3,4‐thiadiazole

The accumulation voltammetry of mercury(II) was investigated at a carbon paste electrode chemically modified with silica gel functionalized with 2,5‐dimercapto‐1,3,4‐thiadiazole (DTTPSG‐CPE). The repetitive cyclic voltammogram of mercury(II) solution in the potential range ?0.2 to +0.8 V (vs. Ag/AgCl), (0.02 mol L^?1 KNO₃ ; v=20 mV s^?1) show two peaks one at about 0.0 V and other at 0.31 V. However, the cathodic wave peak, around 0.0 V, is irregular and changes its form in each cycle. This peak at about 0.0 V is the reduction current for mercury(II) accumulated in the DTTPSG‐CPE. The anodic wave peak at 0.31 V is well‐defined and does not change during the cycles. The resultant material was characterized by cyclic and differential pulse anodic stripping voltammetry performed with the electrode in differents supporting electrolytes. The mercury response was evaluated with respect to pH, electrode composition, preconcentration time, mercury concentration, “cleaning” solution, possible interferences and other variables. The precision for six determinations (n=6) of 0.05 and 0.20 mg L^?1 Hg(II) was 2.8 and 2.2% (relative standard deviation), respectively. The method was satisfactory and used to determine the concentration of mercury(II) in natural waters contaminated by this metal.     

Arthrobacter sp. JS443‐Based Whole Cell Amperometric Biosensor for p‐Nitrophenol

An amperometric microbial biosensor for highly sensitive and selective determination of p‐nitrophenol (PNP) is reported. The biosensor consisted of PNP‐degrader Arthrobacter sp. JS443 immobilized by entrapment in Nafion polymer deposited on the top of the carbon paste electrode transducer. The biosensor was based on the measurement of the oxidation current of the intermediates 4‐nitrocatechol and 1,2,4‐benzenetriol formed by the highly selective oxidation of PNP by Arthrobacter sp. The sensor signal and response time were optimized with applied potential of +0.4 V (vs. Ag/AgCl reference electrode) and 0.03 mg of cells and operating in pH 7.5, 50 mM citrate‐phosphate buffer at room temperature. When operated at optimized conditions, the Arthrobacter sp.‐based biosensor measured as low as 5 nM (0.7 ppb) of PNP. The biosensor demonstrated excellent selectivity with no interference from phenolic compounds such as 2‐nitrophenol, phenol and 3‐chlorophenol but was interfered by 3‐nitrophenol and 3‐methyl‐4‐nitrophenol. It had good precision and intra‐ and inter‐day reproducibility, accuracy and was stable up to 3 days when stored in buffer at 4 °C. When applied for measurement in water from Lake Elsinore, CA, the results obtained were in excellent agreement with the amounts determined spectrophotometrically.     

Carbon Nanotube‐Adsorbed Electrospun Nanofibrous Membranes as Coating for Electrochemical Sensors for Sulfhydryl Compounds

A new method to modify electrodes with carbon nanotubes (CNT) was developed. Multiwalled carbon nanotubes (MWNT) were adsorbed on the electrospun nylon‐6 nanofibrous membranes (Ny‐6‐NFM) and used as a coating to modify conventional glassy carbon electrodes. The modified electrode was designed for the amperometric detection of sulfhydryl compounds with the potential held at +0.3 V vs. Ag/AgCl. The modified electrode showed a linear response for cysteine up to 0.4 mM (R²=0.997), with a sensitivity of 5.1 µA/mM and a detection limit of 15 µM. Other sulfhydryl compounds showed similar results. After use, the Ny‐6‐NFM was easily peeled off, leaving the bare electrode surface back to its original electrochemical behaviour. This is the first attempt to use a disposable membrane functionalized with MWNT for electroanalytical purposes.     

Lignosulfonate‐Modified Electrode for Electrocatalytic Reduction of Acidic Nitrite

Sodium lignosulfonate (LS) undergoes oxidative electropolymerization on a glassy carbon (GC) electrode from sulfuric acid solution to form a chemically modified electrode exhibiting anionic character and redox activity. Cyclic voltammetry reveals the existence of two redox systems at E°′ values of +0.29 and +0.53 V, respectively. Peak currents are proportional to the scan rate as expected for surface confined systems. The GC|poly‐LS electrode shows electrocatalytic activity toward the reduction of acidic nitrite. When operating in a constant potential amperometric mode (at 0.0 V, vs. Ag/AgCl), a linear relationship between nitrite concentration and reduction current is observed over the range of 1 to 250 μM. The detection limit reaches 0.3 μM (S/N=3). The electrode may be practically applied for nitrite determination in human saliva.     

Carbon Nanostructured Screen‐printed Electrodes Modified with CuO/Glucose Oxidase/Maltase/SiO2 Composite Film for Maltose Determination

A sensitive voltammetric method was developed to determine maltose in beverage products using a carbon nanostructured screen‐printed electrode modified with CuO/glucose oxidase/maltase/SiO₂ biocomposite film. Adding CuO particles was done to possess catalytic activity toward hydrogen peroxide. Electrode modified by glucose oxidase and maltase shows a good response to maltose. A well‐defined reduction peak was registered at the potential of ?0.55 V (vs. Ag/AgCl) which intensity increases linearly with the concentration of maltose ranging from 0.01 to 0.1 mmol L^?1. The calculated limit of detection was 0.005 mmol L^?1. Tested on the beer samples, the developed CuO/glucose oxidase/maltase/SiO₂ biocomposite film covered carbon nanostructured screen‐printed electrode is showed to be a prospective sensitive element of the third generation biosensor for maltose.     

Urea Biosensor Based on Electrochromic Properties of Prussian Blue

Prussian blue (PB) is an electrochromic material, which can be used as a signal transducer in the formation of optical urea biosensors. The previous researches in electrochromic properties of PB demonstrated the optical PB response to ammonium ions, which occurs when ammonium ions are interacting with PB layer at a constant 0.2 V vs Ag|AgCl|KCl_sat potential. In this work PB optical dependence on ammonium ions concentration was applied in the formation of electrochromic urea biosensor. Biosensor was formed by modifying the optically transparent indium tin oxide (ITO) coated glass electrode (glass/ITO) with Prussian blue layer and immobilizing urease (glass/ITO/PB‐urease). Calibration curve showed the linear dependency (R²=0.995) between the change of maximal absorbance (ΔA) and urea concentration in concentration range varying from 3 mM to 30 mM. The highest sensitivity (4 ΔA M^?1) of glass/ITO/PB‐urease biosensor is in the concentration range from 7 mM to 30 mM. It was determined that working principle of the glass/ITO/PB‐urease biosensor is not related to pH changes occurring during enzymatic hydrolysis of urea.     

Polyaniline‐Modified Silver and Binary Silver‐Cobalt Catalysts for Oxygen Reduction Reaction

Novel dendrite‐like silver particles were electrodeposited on Ti substrates from a supporting electrolyte‐free 30 mmol L^?1 Ag(NH₃)₂⁺ solution, to synthesize the den‐Ag/Ti electrode. Binary Ag_xCo_y/Ti electrodes with different Ag:Co atomic ratios were further obtained by electrodeposition of Co particles on the den‐Ag/Ti electrode. Polyaniline (PANI) modified den‐Ag/Ti and Ag_xCo_y/Ti electrodes, PANI(n)‐den‐Ag/Ti and PANI(n)‐Ag_xCo_y/Ti, were also obtained by cyclic voltammetry at different numbers of cycles (n) in acidic and alkaline solutions containing aniline, respectively. All these electrodes exhibit high electroactivity for oxygen reduction reaction (ORR) in alkaline solution and their electroactivities follow the order: PANI(15)‐Ag₃₁Co₆₉/Ti>Ag₃₁Co₆₉/Ti>PANI(20)‐den‐Ag/Ti>den‐Ag/Ti. Among them, PANI(15)‐Ag₃₁Co₆₉/Ti displays the highest electrocatalytic activity for ORR with a much positive onset potential of 0 V (vs. Ag/AgCl) and a high ORR current density of 1.2 mA cm^?2 at ?0.12 V (vs. Ag/AgCl). The electrocatalysts are electrochemically insensitive to methanol and ethanol oxidation, and, as cathode electrocatalysts of direct alcohol fuel cells, can resist poisoning by the possible alcohol crossover from the anode.     

Electrochemical Sensing of NADH and Glutamate Based on Meldola Blue in 1,2‐Diaminobenzene and 3,4‐Ethylenedioxythiophene Polymer Films

The redox mediator Meldola blue (MB) was entrapped into two polymers, poly‐1,2‐diaminobenzene (p‐DAB) and poly‐3,4‐ethylenedioxythiophene (p‐EDOT) by potential cycling and films were applied to NADH oxidation with subsequent glutamate detection using immobilized glutamate dehydrogenase. Both polymer films were tested for electrocatalysis of NADH using amperometry at E_app=0.1 V vs. Ag/AgCl and similar response characteristics were obtained with sensitivity values of 6.1 nA μM^?1, linear range up to 0.5 mM (R²=0.9972) and LOD of 50 μM. Subsequent amperometric determination of glutamate resulted in sensitivity 0.7 nA μM^?1, linearity 0–100 μM and detection limit of 2 μM glutamate.     

Manganese Oxide Nanoparticles/Reduced Graphene Oxide as Novel Electrochemical Platform for Immobilization of FAD and its Application as Highly Sensitive Persulfate Sensor

In this study, manganese oxide nanoparticles/reduced graphene oxide(MnOxNPs/rGO) was used as support for strong immobilization of flavin adenine dinucleotide(FAD). A thin film of rGO cast on the electrode surface, followed by performing electrodeposition of MnOxNPs at applied constant potential of +1.4 V vs. Ag/AgCl for 200 s. Finally, FAD was electrodeposited onto the rGO/MnOxNPs film by potential cycling between 1.0 to ?1.0 V in solution containing 1 mg ml^?1 FAD. Electrochemical properties and catalytic activity of GCE/rGO‐MnOxNPs/FAD toward persulfate (S₂O₈^2?) reduction was investigated. Under optimized condition, the concentration calibration range, detection limit, and sensitivity were 0.1 μM–2 mM, 90 nM and 125.8 nA/μM, respectively, using hydrodynamic amperometry technique.     

Conformational Analysis of 1,2‐Di‐O‐Octanoyl‐Ethylene‐Glycerol During Aggregation

Conformational analysis of 1,2‐di‐O‐octanoyl‐ethylene‐glycerol during aggregation by 600 MHz ¹H NMR is described. In monomeric states, 1,2‐di‐O‐octanoyl‐ethylene‐glycerol exists in 75% anti‐conformer and 25% gauche‐conformer. The first critical micelle concentration of 1,2‐di‐O‐octanoyl‐ethylene‐glycerol is calculated to be 4.5 mM. In micellar states, 1,2‐di‐O‐octanoyl‐ethylene‐glycerol exists in 25% anti‐conformer and 75%) gauche‐conformer. When the concentration is greater than 10 mM, 1,2‐di‐O‐octanoyl‐ethylene‐glycerol probably aggregates to become the larger micelle, micelle II. In the second micellar state, 1,2‐di‐O‐octanoylethylene‐glycerol only exists in gauche‐conformer.     

Poly(pyrrole‐co‐pyrrole‐2‐carboxylic acid)/Pyruvate Oxidase Based Biosensor for Phosphate: Determination of the Potential,and Application in Streams

A biosensor based on conductive poly(pyrrole‐co‐pyrrole‐2‐carboxylic acid) [Poly(Py‐co‐PyCOOH)] copolymer film coated gold electrode was developed for the quantitative phosphate determination. Enzyme pyruvate oxidase was immobilized chemically via the functional carboxylated groups of the copolymer. The potential to be applied which is deficiency of phosphate biosensor studies for precise phosphate detection was clarified by using differential pulse voltammetry technique. Performance of the sensing ability of the biosensor was improved by optimizing cofactor/cosubstrate concentrations, polymeric film density and pH. The biosensor showed a linearity up to phosphate concentration of 5 mM, operational stability with a relative standard deviation (RSD) of 0.07 % (n=7) and accuracy of 101 % at ?0.15 V (vs. Ag/AgCl). Detection limit (LOD) and sensitivity were calculated to be 13.3 μM and 5.4 μA mM^?1 cm^?2, respectively by preserving 50 % of its initial response at the end of 30 days. It's performance was tested to determine phosphate concentrations in two streams of Zonguldak City in Turkey. Accuracy of phosphate measurement in stream water was found to be 91 %.     

Anti‐cancer Herbal Drug Berberine – Sensitive Determination Using Boron‐doped Diamond Electrode

Determination of berberine, an isoquinoline plant alkaloid, with antibacterial, antiparasitic, antifungal, hypotensive and antitumoral effects, was proposed by introducing square wave voltammetry on boron‐doped diamond electrode. At optimized experimental parameters, in Britton‐Robinson buffer solution pH 5 berberine provides 3 oxidation peaks (+0.63; +1.14 and +1.34 V) and one reduction (+0.15 V) (vs. Ag/AgCl electrode), with good repeatability (relative standard deviation of 2.6 % and 1.9 % for 8 measurements at 0.5 and 10 µM concentration level, respectively). Calibration curve was linear in wade linear range from 0.1 to 50 µM with limit of detection of 0.04 µM. The proposed procedure was successfully applied for the determination of berberine in seed extract from Argemone mexicana with satisfactory recovery (102–102.6 %). The developed method may represent a sensitive alternative to highly toxic mercury electrodes, modified electrodes and chromatographic methods.     

Electrochemical Fabrication and Properties of Highly Ordered Fe‐Doped TiO2 Nanotubes

Highly‐ordered Fe‐doped TiO₂ nanotubes (TiO₂nts) were fabricated by anodization of co‐sputtered Ti–Fe thin films in a glycerol electrolyte containing NH₄F. The as‐sputtered Ti–Fe thin films correspond to a solid solution of Ti and Fe according to X‐ray diffraction. The Fe‐doped TiO₂nts were studied in terms of composition, morphology and structure. The characterization included scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, X‐ray diffraction, UV/Vis spectroscopy, X‐ray photoelectron spectroscopy and Mott–Schottky analysis. As a result of the Fe doping, an indirect bandgap of 3.0 eV was estimated using Tauc’s plot, and this substantial red‐shift extends its photoresponse to visible light. From the Mott–Schottky analysis, the flat‐band potential (E_fb) and the charge carrier concentration (N_D) were determined to be ?0.95 V vs Ag/AgCl and 5.0 ×10¹⁹ cm^?3 respectively for the Fe‐doped TiO₂nts, whilst for the undoped TiO₂nts, E_fb of ?0.85 V vs Ag/AgCl and N_D of 6.5×10¹⁹ cm^?3 were obtained.     

Non‐enzymatic Fructose Sensor Based on Co3O4 Thin Film

In this study, we report on the selective of fructose on Co₃O₄ thin film electrode surface. A facile chemical solution deposition technique was used to fabricate Co₃O₄ thin film on fluorine doped tin oxide, FTO, glass. Electrode characterization was done using XRD, HRTEM, SEM, AFM, and EIS. The constructed sensor exhibited two distinctive linear ranges (0.021–1.74 mM; 1.74–∼15 mM) covering a wide linear range of up to ∼15 mM at an applied potential of +0.6 V vs Ag/AgCl in 0.1 M NaOH solution. The sensor demonstrated high, reproducible and repeatable (R.S.D of <5 %) sensitivity of 495 (lower concentration range) & 53 (higher concentration range) μA cm⁻² mM⁻¹. The sensor produced a low detection limit of ∼1.7 μM (S/N =3). The electrode was characterised by a fast response time of <6 s and long term stability. The repeatability and stability of the electrode resulted from the chemical stability of Co₃O₄ thin film. The sensor was highly selective towards fructose compared to the presence of other key interferences i. e. AA, AC, UA. The ease of the electrode fabrication coupled with good electrochemical activity makes Co₃O₄ thin film, a promising candidate for non‐enzymatic fructose detection.     

Voltammetric Detection of Captopril Using Copper(II) and an Unmodified Glassy Carbon Electrode

We report a simple, sensitive, and rapid detection of captopril using copper(II) and a bare glassy carbon electrode with cyclic voltammetry. The captopril is detected by the formation of a copper(II)‐captopril complex that is observed to have a characteristic oxidation potential at+0.24 V vs. Ag/AgCl. It is found that the peak current varies linearly with the concentration of captopril. The linear dynamic range is obtained for a captopril concentration of 1 µM to 10 µM, and the sensitivity is found to be 0.10±0.003 μA μM^?1. Importantly, the low limit of detection (n=3) of 0.10 μM and the precision of 3.2 %, are achieved using a simple, unmodified electrode. This is attributable to in situ adsorption of a copper(II)‐captopril complex on the electrode surface.     

Glucose Biosensor Based on Multi‐Walled Carbon Nanotube Modified Glassy Carbon Electrode

An amperometric glucose biosensor based on multi‐walled carbon nanotube (MWCNT) modified glassy carbon electrode has been developed. MWCNT‐modified glassy carbon electrode was obtained by casting the electrode surface with multi‐walled carbon nanotube materials. Glucose oxidase was co‐immobilized on the MWCNT‐modified glassy carbon surface by electrochemical deposition of poly(o‐phenylenediamine) film. Enhanced catalytic electroreduction behavior of oxygen at MWCNT‐modified electrode surface was observed at a potential of ?0.40 V (vs. Ag|AgCl) in neutral medium. The steady‐state amperometric response to glucose was determined at a selected potential of ?0.30 V by means of the reduction of dissolved oxygen consumed by the enzymatic reaction. Common interferents such as ascorbic acid, 4‐acetamidophenol, and uric acid did not interfere in the glucose determination. The linear range for glucose determination extended to 2.0 mM and the detection limit was estimated to be about 0.03 mM.     

SDS‐modified Nanoporous Silver as an Efficient Electrocatalyst for Selectively Converting CO2 to CO in Aqueous Solution

Selectively electrochemical conversion of CO₂ into organic fuel using renewable electricity is one of the most sought‐after processes. In this paper, we report the electrochemical reduction of CO₂ (CO₂RR) on the nanoporous Ag electrodes made of compacted Ag nanoparticles (AgNPs), which were prepared by one‐step reduction in the water phase with or without the surfactant sodium dodecyl sulfate (SDS). The scanning electron microscope (SEM) characterizations show that the compacted Ag electrodes have the nanoporous morphology formed by stacking AgNPs. Compared with the nanoporous Ag electrode without SDS modification (C‐AgNPs), the SDS‐modified AgNPs electrode (C‐AgNPs‐SDS) is highly effective in improving selective CO production in a wide range of potentials (–0.69 V — –1.19 V, vs. RHE), with a Faradaic efficiency of 92.2% and a current density of –8.23 mA·cm^–2 for CO production at –0.79 V (vs. RHE). C‐AgNPs‐SDS is also catalytically stable with only less than 7% deactivation after 8 h of continuous electrolysis.