Laccase Biosensor Based on N‐Succinimidyl‐3‐Thiopropionate‐Functionalized Gold Electrodes

A laccase biosensor, in which the enzyme was immobilized on N‐succinimidyl‐3‐thiopropionate (NSTP)‐modified gold electrodes, is reported. Two different approaches for the preparation of N‐succinimidyl‐terminated monolayers were evaluated: a) activation of a preformed 3‐mercaptopropionic acid (MPA) SAM by reaction with 1‐(3‐dimethylaminopropyl)‐ 3‐ethylcarbodiimide (EDC) and N‐hydroxysulfosuccinimide (NHS); b) assembling of dithiobisuccinimidyl propionate (DTSP). NSTP‐modified electrodes were characterized by cyclic voltammetry and electrochemical impedance spectroscopy. Biosensors prepared by covalent binding of the enzyme and by cross‐linking with glutaraldehyde atop NSTP‐modified electrodes were compared in terms of sensitivity and operational range for caffeic acid. A much better analytical performance was found using the latter approach. Variables affecting the amperometric detection (enzyme loading, pH and applied potential) were optimized. The operational stability and characteristics of functioning of the laccase biosensor in terms of repeatability of the amperometric measurements, reproducibility with different biosensors and useful lifetime, were evaluated. The kinetic parameters of the enzyme reactions and the analytical characteristics of the corresponding calibration plots were calculated for eight phenolic compounds. Limits of detection of 0.07 μM, 0.05 μM and 0.09 μM were obtained for caffeic acid, catechol and 3,4‐dihydroxyphenylacetic acid (DOPAC), respectively. The practical usefulness of the developed biosensor was evaluated by estimating the “pool” of phenolic compounds in olive oil mill wastewaters (OMW).     

Carbon Nanotubes‐Based Amperometric Cholesterol Biosensor Fabricated Through Layer‐by‐Layer Technique

A carbon nanotubes‐based amperometric cholesterol biosensor has been fabricated through layer‐by‐layer (LBL) deposition of a cationic polyelectrolyte (PDDA, poly(diallyldimethylammonium chloride)) and cholesterol oxidase (ChOx) on multi‐walled carbon nanotubes (MWNTs)‐modified gold electrode, followed by electrochemical generation of a nonconducting poly(o‐phenylenediamine) (PPD) film as the protective coating. Electrochemical impedance measurements have shown that PDDA/ChOx multilayer film could be formed uniformly on MWNTs‐modified gold electrode. Due to the strong electrocatalytic properties of MWNTs toward H₂O₂ and the low permeability of PPD film for electroacitve species, such as ascorbic acid, uric acid and acetaminophen, the biosensor has shown high sensitivity and good anti‐interferent ability in the detection of cholesterol. The effect of the pH value of the detection solution on the response of the biosensor was also investigated. A linear range up to 6.0 mM has been observed for the biosensor with a detection limit of 0.2 mM. The apparent Michaelis‐Menten constant and the maximum response current density were calculated to be 7.17 mM and 7.32 μA cm^?2, respectively.     

A Third‐Generation Hydrogen Peroxide Biosensor Based on Horseradish Peroxidase Covalently Immobilized on Electrografted Organic Film on Screen‐Printed Carbon Electrode

A new convenient strategy to fabricate a third‐generation hydrogen peroxide biosensor was described. The screen‐printed carbon electrode (SPCE) was first modified with a layer of 4‐nitrophenyl assembled from the 4‐nitroaniline diazonium salt synthesized in situ in acidic aqueous solution. Next, the nitro groups were converted to amines followed by crosslinking to the horseradish peroxidase (HRP) by glutaraldehyde. The redox chemistry of the active center of the HRP was observed and the HRP‐modified electrode displayed electrocatalytic activity towards the reduction of hydrogen peroxide (H₂O₂) without any mediators. H₂O₂ was determined in a linear range from 5.0 μM to 50.0 μM, with a detection limit of 1.0 μM. Furthermore, the biosensor exhibited fast amperometric response, good reproducibility and long‐term stability.     

Nickel/Copper Bilayer‐modified Screen Printed Electrode for Glucose Determination in Flow Injection Analysis

This work reports about the performance of a Ni/Cu‐modified screen printed electrodes (SPE/Ni/Cu), prepared by physical vapor deposition (PVD) in an oblique angle configuration (OAD), for non‐enzymatic glucose sensing applications. SPE/Ni/Cu electrodes showed an excellent reversibility and a catalytic behavior for detection of glucose that were controlled by the diffusion of reactants up to the active sites at the electrode surface. The study with a flow injection analysis (FIA) setup of the main experimental variables affecting the detection process has shown that the developed electrode system had an excellent glucose sensitivity of 1.04 A M⁻¹cm⁻² (R²:0.999), a linear response up to 1 mM, a limit of detection of 0.33 μM and a time of analysis of ca. 30 s per sample. The selectivity of the sensor was checked against various interferences, including ascorbic acid, uric acid, acetaminophen and other sugars, in all cases with excellent results. The feasibility of using this sensor for practical applications was successfully confirmed by determining the glucose concentration in different commercial beverages.     

Inkjet Printed Multi‐walled Carbon Nanotube Sensor for the Detection of Lead in Drinking Water

Electroanalytical methods can be used for the reliable detection of the toxic heavy metal lead in drinking water samples. Inkjet printed electrodes have potential for the rapid and affordable assessment of drinking water. Researchers have shown the electrochemical sensing applicability of inkjet printed electrodes. In this work, Pb²⁺ was detected using an inkjet printed multi‐walled carbon nanotube (IJP‐MW‐CNT) electrode with silver tracks printed underneath. The silver tracks provide the sensor with the conductivity needed for sensitive measurements. MW‐CNT were dispersed in water using bile salts as a surfactant to prepare the ink. The IJP‐MW‐CNT electrode was used as the working electrode with a platinum wire and Ag/AgCl as auxiliary and reference electrode, respectively. The electrodes performance was optimized in 0.1 M acetate buffer (pH=4.3) and had two linear ranges of 5 to 20 ppb (R²=0.99) with a sensitivity of 38 nA/ppb and 20 to 50 ppb (R²=0.98) with a sensitivity of 15 nA/ppb and a limit of detection (LOD) of 1.0 ppb for Pb²⁺. The analytical applicability of electrode was determined by constructing a calibration curve in an unaltered drinking water sample (i. e.) Cincinnati tap water with two linear ranges of 15 to 40 ppb (R²=0.99) with a sensitivity of 1.5 nA/ppb and 40 to 70 ppb (R²=0.99) with a sensitivity of 3.5 nA/ppb and a LOD of 1.0 ppb for Pb²⁺. Effects of copper and cadmium as potential interferents are reported.     

Electrogenerated Chemiluminescence Ethanol Biosensor Based on Carbon Nanotube‐Titania‐Nafion Composite Film

Mesoporous titania‐Nafion composite doped with carbon nanotube (CNT) has been used for the immobilization of tris(2,2′‐bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) and alcohol dehydrogenase on an electrode surface to yield a highly sensitive and stable electrogenerated chemiluminescence (ECL) ethanol biosensor. The presence of CNT in the composite film increases not only the sensitivity of the ECL biosensor but also the long‐term stability of the biosensor. The present biosensor responds linearly to ethanol in the wide concentration ranges from 1.0×10^?5 M to 1.0×10^?1 M with a detection limit of 5.0×10^?6 M (S/N=3). The present ECL ethanol biosensor exhibited higher ECL response compared to that obtained with the ECL biosensor based on the corresponding composite without CNT. The present CNT‐based ECL biosensor showed good long‐term stability with 75% of its initial activity retained after 2 weeks of storage in 50 mM phosphate buffer at pH 7.0.     

Amperometric Biosensor for Hydrogen Peroxide,Using Supramolecularly Immobilized Horseradish Peroxidase on the β‐Cyclodextrin‐Coated Gold Electrode

Horseradish peroxidase, previously modified with 1‐adamantane moieties, was supramolecularly immobilized on gold electrodes coated with perthiolated β‐cyclodextrin. The functionalized electrode was employed for the construction of an amperometric biosensor device for hydrogen peroxide using 1 mM hydroquinone as electrochemical mediator. The biosensor exhibited a fast amperometric response (6 s) and a good linear response toward H₂O₂ concentration between 12 μM and 450 μM. The biosensor showed a sensitivity of 1.02 mA/M cm², and a very low detection limit of 5 μM. The electrode retained 97% of its initial electrocatalytic activity after 30 days of storage at 4 ⁰C in 50 mM sodium phosphate buffer, pH 7.0.     

Detection of Trace Phenol Based on Mesoporous Silica Derived Tyrosinase‐Peroxidase Biosensor

A novel electrochemical biosensor for phenol based on immobilization of tyrosinase‐peroxidase on mesoporous silica is described. The enhanced sensitivity of the tyrosinase‐horseradish peroxidase based biosensor to phenol was observed on comparing with tyrosinase or horseradish peroxidase monoenzyme modified electrodes. Two enzymes retained their enzymatic activities for phenol determination without any mediator. The preparation conditions of the biosensor are discussed. Optimization of the experimental parameters was performed with regard to pH and operating potential. The phenol sensor exhibited a fast response of less than 10 seconds. The sensitivity of the biosensor for phenol was 14 μA μM^?1 cm^?2 with a linear range from 2×10^?7 to 2.3×10^?4 M and a detection limit of 4.1×10^?9 M. The biosensor showed a good stability and reproducibility.     

Electrochemical Behaviour of Microwave‐assisted Oxidized MWCNTs Based Disposable Electrodes: Proposal of a NADH Electrochemical Sensor

The effect of the oxidation degree of multiwalled carbon nanotubes (MWCNTs) for the detection of NADH was evaluated in this paper. MWCNTs were oxidized by microwave‐assisted sulfonitic treatment at different times (5, 10, 15, and 30 min) and deposited onto a graphite screen printed electrodes. Oxidized MWCNTs were characterized and the electrochemical performance evaluated. The best sensor in terms of sensitivity and stability was obtained after 15 minutes of oxidation (SPE/CNT15). A significant reduction of the NADH oxidation potential was recorded for oxidized MWCNTs compared with unmodified MWCNTs (0.270 V and 0.500 V, respectively vs. Ag/AgCl pseudo reference electrode), increasing the selectivity of the system. Chronoamperometric calibration curves carried out applying a potential of 0.3 V for 1 min were linear in the 4–35 μM range of NADH. A limit of detection of 1 μM was achieved with negligible surface fouling (three consecutive calibration curves, 30 total measurements: slope decrease 5.9 %). Inter electrode reproducibility (n=13) was good resulting in RSD of 15.2 % and 5.0 % for the peak intensity and the oxidation potential, respectively. Quantification of glucose in white wine samples was carried out to demonstrate the ability of the NADH sensor to work in real samples. A good correlation with a spectrophotometric kit for the glucose quantification was achieved.     

Natural Melanin Nanoparticle‐decorated Screen‐printed Carbon Electrode: Performance Test for Amperometric Determination of Hexavalent Chromium as Model Trace

A biosensor was prepared with natural melanin nanoparticles (MNP) decorated on a screen‐printed carbon electrode (SPCE). Hexavalent chromium was selected as a well‐known heavy metal ion to be detected for testing the performance of novel biosensor. Natural MNP was extracted from cuttlefish (Sepia officinalis) ink. Surface decoration of SPCEs with MNP was performed by two different methods. The first one was layer‐by‐layer assembly (LBL‐A) for different cycle times(n). In the second one, plasma treatment of SPCE incorporated with evaporation‐induced self‐assembly (EI‐SA) techniques including different incubation times in MNP solutions. The performance of both modified SPCEs were tested for amperometric detection of Cr(VI) in various water samples, and peak reduction of Cr(VI) was determined at 0.33 V. Amperometric results showed wide linear ranges of 0.1–2 μM and 0.1–5 μM of Cr(VI) for SPCEs modified with 14n‐LBL‐A and 12h‐EI‐SA, respectively. The sensitivities of SPCEs modified with 14n‐LBL‐A and 12h‐EI‐SA techniques were 0.27 μA μM^?1 and 0.52 μA μM^?1, respectively. In addition, both modified SPCEs selectively detected Cr(VI) in a model aqueous system composed of certain other heavy metals and minerals, and tap and lake water samples. The LOD and LOQ values for 12h‐EI‐SA were 0.03 μM and 0.1 μM, respectively. This showed that MNP‐modified‐SPCEs generated via EI‐SA techniques have the potential to be an alternative to conventional detection methods such as ICP‐MS.     

One‐Step Electrodeposited Carbon Nanotube/Zirconia/Myoglobin Film for Direct Electron Transfer and Electrocatalysis

A nanobiocomposite film consisted of zirconia, multiwalled carbon nanotubes (MWNTs) and Myoglobin (Mb) was electrochemically deposited on the electrode. Direct electron transfer for the immobilized Mb was realized and high electrocatalytic efficiency toward H₂O₂ was observed. The proposed biosensor via a simple one‐step electrodeposition method displayed a broader linear range and a lower detection limit for H₂O₂, as compared with those CNT or ZrO₂ based biosensor. The linear range is from 2 × 10^?6 M to 1 × 10^?3 M with the detection limit of 6 × 10^?7 M. The present strategy provides a simple and effective method to assemble CNT, ZrO₂ and enzyme nanohybrid on the electrode and expands the scope of CNT‐based electrochemical devices.     

Low Cost Layer by Layer Construction of CNT/Chitosan Flexible Paper‐based Electrodes: A Versatile Electrochemical Platform for Point of Care and Point of Need Testing

Modification of cellulosic paper with carbon nanotubes (CNT) was studied for the development of electronic and analytical devices. Interesting results were published by using a CNT aqueous solution and the capillary forces of filter paper to make conductive tracks, supercapacitors, potentiometric electrodes and chemometric sensors. In this report, we show for the first time an electrochemical characterization of CNT‐CS‐SDS paper electrodes constructed with an ink containing optimized proportions of multi‐wall CNT, chitosan (CS) and sodium dodecyl sulfate (SDS), and we compared our data with CNT‐SDS paper electrodes constructed with a previously reported ink. We achieved better reversibility (ΔE=131±14 mV, CVs) and reproducibility (RSD=3.63 %) with CNT‐CS‐SDS paper electrodes, when compared to CNT‐SDS paper electrodes (ΔE=249±7 mV; RSD=6.8 %) used as controls. When electrodes were fold at 90° angle, CNT‐CS‐SDS paper electrodes showed lower RSD than CNT‐SDS paper electrodes, 8.43 % and 21.5 % respectively. These results are in concordance with SEM analysis indicating a dense CS film in CNT‐CS‐SDS paper electrodes. As a proof of concept, we determine dopamine concentration by DPV in the presence of ascorbic and uric acids, the limit of detection calculated was 6.32 μM. Moreover, a bismuth‐film was prepared by in situ plating of Bi into CNT‐CS‐SDS paper electrodes. ASV allowed us to detect Pb in the presence of Bi (10–200 ppb) with a limit of detection of 6.74 ppb.     

Nanomolar Detection of Glutamate at a Biosensor Based on Screen-Printed Electrodes Modified with Carbon Nanotubes

The amperometric glutamate biosensor based on screen-printed electrodes containing carbon nanotubes (CNT), and its integration in a flow injection analysis system, is described herein. The sensor was fabricated by simply adsorbing enzyme glutamate oxidase (GlutOx) on a commercial substrate containing multi-wall CNT. The resulting device displayed excellent electroanalytical properties toward the determination of L-glutamate in a wide linear range (0.01-10 μM) with low detection limit (10 nM, S/N≥3), fast response time (≤5 s), and good operational and long-term stability. The CNT modified screen-printed electrodes have a potential to be of general interest for designing of electrochemical sensors and biosensors.     

Design of a new hypoxanthine biosensor: xanthine oxidase modified carbon film and multi-walled carbon nanotube/carbon film electrodes

A new and simple-to-prepare hypoxanthine biosensor has been developed using xanthine oxidase (XOD) immobilised on carbon electrode surfaces. XOD was immobilised by glutaraldehyde cross-linking on carbon film (CF) electrodes and on carbon nanotube (CNT) modified CF (CNT/CF). A comparison of the performance of the two configurations was carried out by the current response using amperometry at fixed potential; the best characteristics being exhibited by XOD/CNT/CF modified electrodes. The effects of electrolyte pH and applied potential were evaluated, and a proposal is made for the enzyme mechanism of action involving competition between regeneration of flavin adenine dinucleotide and reduction of hydrogen peroxide. Under optimised conditions, the determination of hypoxanthine was carried out at ?0.2 V vs. a saturated calomel electrode (SCE) with a detection limit of 0.75 μM on electrodes with CNT and at ?0.3 V vs. SCE with a detection limit of 0.77 μM on electrodes without CNT. The applicability of the biosensor was verified by performing an interference study, reproducibility and stability were investigated, and hypoxanthine was successfully determined in sardine and shrimp samples.     

Disposable Amperometric Biosensor Based on Poly‐L‐lysine and Fe3O4 NPs‐chitosan Composite for the Detection of Tyramine in Cheese

An amperometric tyramine biosensor based on poly‐L‐lysine (PLL) and Fe₃O₄ nanoparticles (Fe₃O₄NP) modified screen printed carbon electrode (SPCE) was developed. PLL was formed on the SPCE by the electropolymerization of L‐lysine. Subsequently, Fe₃O₄NP suspension prepared in chitosan (CH) solution was casted onto the PLL/SPCE. Tyrosinase (Ty) enzyme was immobilized onto the modified Fe₃O₄?CH/PLL/SPCE and the electrode was coated with Nafion to fabricate the Ty/Fe₃O₄?CH/PLL/SPCE. Different techniques including scanning electron microscopy, chronoamperometry (i–t curve), cyclic voltammetry and electrochemical impedance spectroscopy were utilized to study the fabrication processes, electrochemical characteristics and performance parameters of the biosensor. The analytical performance of the tyramine biosensor was evaluated with respect to linear range, sensitivity, limit of detection, repeatability and reproducibility. The response of the biosensor to tyramine was linear between 4.9×10^?7–6.3×10^?5 M with a detection limit of 7.5×10^?8 M and sensitivity of 71.36 μA mM^?1 (595 μA mM^?1 cm^?2). The application of the developed biosensor for the determination of tyramine was successfully tested in cheese sample and mean analytical recovery of added tyramine in cheese extract was calculated as 101.2±2.1 %. The presented tyramine biosensor is a promising approach for tyramine analysis in real samples due to its high sensitivity, rapid response and easy fabrication.     

A Simple Layer‐by‐Layer Assembly Strategy for a Reagentless Biosensor Based on a Nanocomposite of Methylene Blue‐Multiwalled Carbon Nanotubes

A simple layer‐by‐layer (LBL) assembly strategy was established for constructing a novel reagentless biosensor based on a nanocomposite of methylene blue multiwalled carbon nanotubes (MB‐MWNTs). A nanocomposite of MB‐MWNTs was obtained by direct premixing and possessed good dispersion in barbital‐HCl buffer. Through electrostatic interactions, the nanocomposite of MB‐MWNTs could alternately be assembled with horseradish peroxidase (HRP) on the Au electrode modified with precursor films. UV/Vis spectra and scanning electron microscopy (SEM) were applied to reveal the formation of the nanocomposite of MB‐MWNTs. The LBL assembly process was also verified by electrochemical impedance spectroscopy (EIS). The MB is a well‐established mediator and efficiently facilitated the electron shuttle between the HRP and the electrode, as demonstrated by the cyclic voltammetry (CV) measurements. The as‐prepared reagentless biosensor exhibited a fast response for the determination of hydrogen peroxide (H₂O₂) and reached 95% of the steady‐state current within 3 s. It was found that the linear response range of the reagentless biosensor for H₂O₂ was from 4.0 μM to 3.78 mM with a detection limit of 1.0 μM and a sensitivity of 22.5 μA mM⁻¹. The biosensor exhibited a high reproducibility and stability.     

Fabricating of Acetylcholine Biosensor by a Layer‐by‐layer Deposition Technique for Determining Trichlorfon

An acetylcholine (ACh) biosensor has been fabricated with bienzymes/poly(diallyldimethylammonium chloride) (PDDA) multilayer film‐modified platinum (Pt) electrodes by a layer‐by‐layer technique (LBL). The ACh biosensor was optimized and the properties are described. This ACh biosensor was used for the detection of organophosphate pesticide trichlorfon. The detection limits (found 0.001 μg/mL for trichlorfon) make it possible to detect the pollutants. This simple protocol of biosensor preparation, high sensitivity and stability are very promising for the determination of environmental pollutants in field conditions.     

Electrochemical Oxidation and Sensitive Determination of Pyrogallol at Preanodized Screen‐Printed Carbon Electrodes

In this study, we report a simple, low‐cost and rapid electrochemical sensor based on the anodically pretreated screen‐printed carbon electrodes (SPCE*) for the determination of pyrogallol in pH 7.0 buffer solutions. Cyclic voltammetric studies show that SPCE* lowers overpotentials and improve electrochemical behaviour of pyrogallol, compared to untreated SPCE. All experimental parameters were optimized to improve voltammetric responses; excellent analytical features were achieved by flow‐injection amperometric methods. A linear calibration plot was obtained for 10‐1000 μM pyrogallol with a slope of 0.0562 μA/μM. The detection limit (S/N = 3) was 0.33 μM. Interferences from some inorganic salts and organic compounds were studied. The assay was applied to the determination of pyrogallol in tap water and lake water, respectively.     

The Modification of Screen‐Printed Carbon Electrodes with Amino Group and Its Application to Construct a H2O2 Biosensor

Electrooxidation of thionine on screen‐printed carbon electrode gives rise to the modification of the surface with amino groups for the covalent immobilization of enzymes such as horseradish peroxidase (HRP). The biosensor was constructed using multilayer enzymes which covalently immobilized onto the surface of amino groups modified screen‐printed carbon electrode using glutaraldehyde as a bifunctional reagent. The multilayer assemble of HRP has been characterized with the cyclic voltammetry and the faradaic impedance spectroscopy. The H₂O₂ biosensor exhibited a fast response (2 s) and low detection limit (0.5 μM).     

Amperometric Biosensors for Tyramine Determination Based on Graphene Oxide and Polyvinylferrocene Modified Screen‐printed Electrodes

A comparison of the analytical characteristics of two tyramine biosensors, based on graphene oxide (GRO) and polyvinylferrocene (PVF) modified screen‐printed carbon electrodes (SPCE), is reported. Diamine oxidase (DAOx) or monoamine oxidase (MAOx) was immobilized onto the PVF/GRO modified SPCE to fabricate the biosensors. Surface characteristics and electrochemical behaviour of the modified SPCEs were investigated by atomic force microscopy (AFM), scanning electron microscopy (SEM), energy dispersive X‐ray spectroscopy (EDX) and cyclic voltammetry (CV). Electrode surface composition and experimental variables such as pH and working potential were optimized in order to ensure a high performance. Under optimum experimental conditions, both DAOx/PVF/GRO/SPCE and MAOx/PVF/GRO/SPCE biosensors exhibited wide linear dynamic ranges for tyramine from 9.9×10^?7 to 1.2×10^?4 M and from 9.9×10^?7 to 1.1×10^?4 M, respectively. MAOx/PVF/GRO/SPCE biosensor showed higher sensitivity (11.98 μA mM^?1) for tyramine determination than the DAOx/PVF/GRO/SPCE biosensor (7.99 μA mM^?1). The substrate specifity of the biosensors to other biogenic amines namely histamine, putrescine, spermine, spermidine, tryptamine, β‐phenylethylamine and cadaverine was also investigated. The developed biosensors were successfully used for tyramine determination in cheese sample.