Magnetic and transport properties in double-doping La(2+4x)/3Sr(1−4x)/3Mn1–xCuxO3 (0⩽x⩽0.20) systems

A series of the double-doping samples La_(2+4x)/3Sr_(1−4x)/3Mn_1–xCu_xO₃(0?x?0.2)$(0?x?0.2)$with the Mn³⁺/Mn⁴⁺ ratio fixed at 2:1 and the single-doping samples La_2/3Sr_1/3Mn_1–xCu_xO₃(0?x?0.2)$(0?x?0.2)$ have been investigated. For the double-doping samples, though the ratio Mn³⁺/Mn⁴⁺=2:1 has been generally recognized the optimum ratio, the Curie temperature _TC$T_{\mathrm{C}}$ and metallic–insulator transition temperature _Tp1$T_{\mathrm{p}1}$ are more rapidly decreased by Cu substitution than that corresponding to single-doping samples. And the resistivity ρ$\rho$ value for the double doping is larger about two or three orders of magnitude than that corresponding to single doping. At the same time, two resistivity peaks and two magnetoresistance (MR) peaks appear. We suggest that for the double-doping samples the A-site cation size 〈r_A〉 and the A-site mismatch factor σ²${\sigma }^2$ decreases with increasing doping level, which leads to the system microstructural distortion. This microstructural distortion makes the Mn³⁺–O–Mn⁴⁺ cut off more cluster-spin except for the clusters induced by Cu. These cluster interfaces contribute to ρ$\rho$, which exceeds far the contribution of e_g electron decreasing with doping increasing in the single doping. At the same time, such interface scattering also gives rise to the appearance of second peak for the double-doping samples. The experimental results shows that double doping could be also a potential way in tuning colossal MR (CMR), which can give a guide for the adequate selection of CMR materials.     

Magnetic,transport and microstructural properties of polycrystalline samples with nominal composition of La0.7Ca0.3Mn1−xVxO3 (0⩽x⩽0.2)

Polycrystalline samples with nominal composition of La_0.7Ca_0.3Mn_1−xV_xO₃ (0?x?0.2) sintered in air were investigated by ac susceptibility, dc magnetization, magnetoresistance (MR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and differential thermal analysis (DTA) measurements. It is found that V could not substitute for Mn to form La_0.7Ca_0.3Mn_1−xV_xO₃ phase when the samples are sintered in air. The obtained samples contain several phases such as (La, Ca)Mn_1−δO₃, LaCa₃V₃O₁₂, Mn₃O₄ phases, etc. and constitute multi-phase composites. The Curie temperature T_C and spontaneous magnetization of the composites decrease, and the resistance of the composites increases as the V content increases. The addition of V may effectively improve the low-field MR response at low temperatures due to the variation in the microstructure of the composites.     

Structural and magnetic properties of Zn1−xCoxO (0<x⩽0.30) nanoparticles

We present a systematic investigation on the structural and magnetic properties of Zn_1−xCo_xO nanoparticles synthesized by an auto-combustion method. The single-phase Zn_1−xCo_xO crystallize in the wurtzite-type structure with a homogeneity range as large as x≈0.30, which enables the observation of some anomalies. The lattice parameter a and the unit cell volume V increase with the Co content, and anomalies are discernable around x=0.15 on the a−x and V−x curves. The magnetization data show no evidence of ferromagnetic (FM) ordering in our samples down to T=5 K, and the magnetization at 5 K and 5 T exhibits a maximum around x=0.125. Based on the detailed analysis of the magnetization data and the donor impurity band exchange model, the anomalies on composition dependence of both the lattice parameters and magnetization can be associated with an occurrence of cation percolation around the threshold x_p (≈1.5/Z=0.125 for three-dimensional lattice with coordination number Z=12). Within the framework of the donor impurity band exchange model, the absence of FM in the well-characterized Zn_1−xCo_xO can be attributed to insufficient donor electron concentration.     

Double M–I transitions and low-temperature resistivity minimum of La2/3Ca1/3Mn1−xCoxO3(0⩽x⩽0.15) manganite

A series of Mn-site Co-doping samples La_2/3Ca_1/3Mn_1−xCo_xO₃ (0?x?0.15) have been prepared. The structure, magnetic and transport properties of this system have been systematically investigated. All the samples showed good single phase, and the lattice parameters decreased with the increase of doping concentration x. Only one paramagnetic–ferromagnetic transition was observed. The Curie temperature T_C decreases gradually and the transition width becomes wider with the increase of x. The abnormal transport properties were induced by Co doping, characterized by the double metal–insulator transitions and low-temperature minimum behavior. The present results are discussed and possible explanations were given based on the related theory and previous reported results.     

Fluorination of perovskite-related phases of composition La1−xSrxFe1−yCoyO3−δ

We report here on the fluorination of the perovskite-related phases La_1−xSr_xFe_1−yCo_yO_3−δ. The introduction of fluorine in place of oxygen is achieved through a low-temperature (400 °C) reaction with poly(vinylidene fluoride). X-ray powder diffraction data show that in all cases the fluorination leads to an expansion in the unit cell, which is consistent with partial replacement of oxygen by fluorine and consequent reduction in the oxidation state of iron and/or cobalt. This reduction in oxidation state is confirmed by X-ray absorption- and Mössbauer-spectroscopy. The Mössbauer spectra show complex magnetically split hyperfine patterns for the fluorinated samples, reflecting the interactions between Fe³⁺ ions, which are not possible in oxides containing Fe⁴⁺.     

Heterogeneous magnetic and electronic states in Ca1−xLaxMnO3−δ (x⩽0.12) single crystals with electron doping

The magnetic, transport, and optical properties of electron-doped Ca_1−xLa_xMnO_3−δ single crystals with x  ?0.12 were studied. The magnetic measurements show that in single crystals with x=0$x=0$ and 0.05 the G-type AFM phase with weak FM component is realized and in crystals with x=0.10$x=0.10$ and 0.12 the G- and C-type AFM phases coexist. The C-type magnetic structure arises at less concentration of La than in polycrystalline samples as a result of oxygen vacancies being additional source of electrons. Under magnetic transitions in the G- and C-type phases, resistivity and magnetoresistance of the doped single crystals have anomalies. Optical absorption in IR range indicates formation of a charge gap in crystals with x=0.10$x=0.10$ and 0.12 at appearance of the C-AFM and monoclinic phase with orbital/charge ordering. By comparing optical and transport properties, heterogeneous electronic state and its relation with heterogeneous magnetic state are shown.     

High-temperature electronic transport properties of La1−xCaxMnO3+δ (0.0?x?1.0)

La_1−xCa_xMnO_3+δ (0.0?x?1.0) samples were prepared and their resistivity and Seebeck coefficients were measured in the high-temperature range. Ca doping changes the ratio of Mn³⁺/Mn⁴⁺ and influences the electronic transport behavior markedly. With the increase of Ca concentration, the samples change from a p-type semiconductor to an n-type one and Seebeck coefficient becomes increasingly negative. Low doping (x=0.2) and high doping (x=0.8) induces the drop of the resistivity compared with undoped LaMnO_3+δ and CaMnO_3+δ samples due to the rise of carrier concentration. However, the resistivity of moderate-doped samples (x=0.4, 0.6) is larger than low- and high-doped samples because dopant scattering decreases carrier mobility.     

Non-adiabatic polaron hopping conduction in CaMn1−xCrxO3 (0?x?0.3)

DC electrical conductivity (σ_dc) of electron-doped antiferromagnetic CaMn_1−xCr_xO₃ (0?x?0.3) has been discussed elaborately in the light of polaron hopping conduction. The increase in Cr doping concentration increases the conductivity and decreases the activation energy. Non-adiabatic polaron hopping conduction is observed in all the manganites at high temperatures. The analysis of σ_dc data shows that small polarons are formed at lower concentrations (?5%) of Cr doping and undoped samples. However, large polarons are materialized at higher doping (?10%) concentrations. This is consistent with the fact that doped Cr³⁺ has larger ionic size compared to that of Mn⁴⁺. Again, strong electron-phonon (e-ph) interaction is perceived in undoped and 5% Cr-doped samples but not in manganites with larger doping concentration. This also confirms the formation of larger polarons with the increase of x. Mott's variable range hopping (VRH) model can elucidate the dc conductivity at very low temperatures. It has been detected that single phonon-assisted hopping is responsible for the dc conduction in the Cr-doped CaMnO₃ manganites.     

Low-temperature synthesis of nanocrystalline Ca1−xHoxMnO3−δ (0?x?0.3) powders

Nanocrystalline Ca_1−xHo_xMnO_3−δ (0?x?0.3) manganites were synthesized as phase-pure by a simple and instantaneous solution autogel combustion method, which is a low temperature initiated synthetic route to obtain fine grain size. All the samples, heated at 800 °C for 18 h, can be produced as phase-pure; the polycrystalline powders are homogeneous and possess ultrafine particle size. The holmium-doped calcium manganites retain the orthorhombic phase of the undoped sample. The scanning electron microscope (SEM) images revealed that the combustion-derived compounds exhibit particle size that decreases with holmium content from 300 to 80 nm. All manganites show two active IR vibrational modes near 400 and 600 cm⁻¹. The high temperature dependence of resistivity was measured using a standard four-probe method in the range 25-600 °C. All the samples exhibit semiconductor behaviour and holmium induces a marked decrease in the electrical resistivity when compared with the parent CaMnO₃. The results can be well attributed to the Mn⁴⁺/Mn³⁺ ratio and to the particle grain size.     

La2−xSrxCuO4−δ superconducting samples prepared by the wet-chemical method

In this work, we report on the physical properties of good-quality polycrystalline superconducting samples of La_2−xSr_xCu_1−yZn_yO_4−δ (y=0, 0.02) prepared by a wet-chemical method, focusing on the temperature dependence of the critical current. Using the wet-chemical method, we were able to produce samples with improved homogeneity compared to the solid-state method. A complete set of samples with several carrier concentrations, ranging from the underdoped (strontium concentration x≈0.05) to the highly overdoped (x≈0.25) region, were prepared and investigated. The X-ray diffraction analysis, zero-field cooling magnetization and electrical resistivity measurements were reported on earlier. The structural parameters of the prepared samples seem to be slightly modified by the preparation method and their critical temperatures were lower than reported in the literature. The temperature dependence of the critical current was explained by a theoretical model which took the granular structure of the samples into account.     

Structural properties and electrical behaviour in the polycrystalline lanthanum-deficiency La1−x□xMnO3 manganites

Electrical conductance and X-ray diffraction (XRD) measurements of lanthanum-deficiency La_1−x□_xMnO₃ (x=0.05, 0.10 and 0.20) polycrystalline samples were performed to examine the effect of the internal pressure at B-site on the conduction mechanism. The structural study reveals that all samples crystallize in the rhombohedral system. The electronic conduction appears to be thermally activated at high temperature, which indicates the presence of semiconductor behaviour. The increase of the x content converts 3x Mn³⁺ to 3x Mn⁴⁺ ions with smaller ionic radius, which reduces the internal pressure and leads to the increase of the one-electron bandwidth W. This increase causes the appearance of metallic behaviour at low temperature for x=0.10 and 0.20 content.     

Structure and magnetic properties of magnetostrictive compounds Tb0.36Dy0.64(Fe0.85Co0.15)2−xBx (0⩽x⩽0.15)

Crystal structure and magnetic properties of magnetostrictive compounds Tb_0.36Dy_0.64(Fe_0.85Co_0.15)_2−xB_x (0?x?0.15) have been investigated at room temperature. The matrix of these compounds keeps a cubic MgCu₂-type structure. Lattice parameter a of the Laves phase decreases to reach a minimum at x=0.10, then increases with increasing boron content. Through analyzing the Mössbauer spectra, the easy magnetization direction (EMD) for all samples is confirmed to lie along 〈111〉 direction at room temperature, suggesting the presence of the giant magnetostriction. The mean hyperfine field H_hf and the deduced iron moment μ_Fe increase with increasing boron content, resulting in the enhancement of both Curie temperature T_C and spin reorientation temperature T_r. Although the addition of B enlarges the magnetocrystalline anisotropy constant K₁, the composition dependence of the ratio λ/K₁ for Tb_0.36Dy_0.64(Fe_0.85Co_0.15)_2−xB_x, however, reaches a maximum value at x=0. 05 under high magnetic fields.     

Structures, magnetic properties, and magnetocaloric effect in MnCo1−xGe (0.02?x?0.2) compounds

The crystalline structures, magnetic properties and magnetocaloric effect (MCE) of MnCo_1−xGe alloys (0.02?x?0.2) have been reported. The crystalline structures of MnCo_1−xGe (x?0.06) alloys are mainly of TiNiSi-type phase, and Ni₂In-type structure dominates for x>0.06. With decreasing Co concentrations the saturated magnetization of these compounds decreases. Large low-field magnetic entropy change −ΔS_M of about 2.3 J/kg K in MnCo_0.94Ge alloy has been obtained for a magnetic field change of 1 T. Moreover, it is found that TiNiSi-type phase exhibits larger −ΔS_M than Ni₂In-type one. For MnCo_0.94Ge alloy, considerable low-field refrigerant capacity (RC) (∼460 mJ/cm³), low coercivity and easy synthesis make these alloys potential candidates for near-room temperature magnetic refrigerants.     

Anomalous Hall effect in sputter-deposited CoxTi1−xO2–δ films

Hall effect measurements were performed on epitaxial Co_xTi_1−xO_2–δ thin films grown on (0 0 1) LaAlO₃ by reactive RF magnetron co-sputter deposition. Magnetization measurements reveal ferromagnetic behavior in M–H loop at room temperature for Co_xTi_1−xO_2–δ thin films for which x?0.02. An anomalous Hall effect was observed for Co_0.10Ti_0.90O_2−δ films grown with the partial pressure of water P(H₂O)=4×10⁻⁴ Torr or less. These films exhibit a positive ordinary Hall coefficient and a positive magnetoresistance. X-ray diffraction on films grown under these conditions shows evidence for Ti_nO_2n−1 phase due to the deficiency of oxygen. In contrast, Hall measurements taken for undoped and Co-doped TiO₂ thin films grown under more oxidizing conditions show only the ordinary Hall effect with a negative Hall coefficient consistent with n-type conduction. For these films, the magnetoresistance was positive and increased monotonically with increasing magnetic field. The results suggest that Co-doped Ti_nO_2n−1 may be a dilute magnetic semiconducting oxide for which the carriers couple to the spin polarization.     

Structural investigation of the BaSnO3–YBa2Cu3O7−x system

We report the microstructure change of BaSnO₃ (BSO)–YBa₂Cu₃O_7−x (YBCO) thin film system grown on SrTiO₃ single crystal substrates by pulsed laser deposition with using the “surface-modified-target” and “mixture-target” methods. Although it was confirmed that the thick BSO nanorods incorporated to YBCO films act as strong artificial pinning centers, the formation mechanism of the nanorods is still unclear. The purpose of this work is to extend the structural investigation to higher contents of BSO (up to 71 vol.%) in order to enlighten the relationship among interfacial energy, morphology and pinning performance in binary BSO–YBCO films.     

Valence changes of manganese and praseodymium in Pr1−xSrxMn1−yInyO3−δ perovskites upon cation substitution as determined with XANES and ELNES

Systematic valence changes in Pr_1−xSr_xMn_1−yIn_yO_3−δ upon cation substitution with Sr²⁺ and In³⁺ have been found using Mn K-edge and Pr L-edge X-ray absorption, and Mn L_II,III and Pr M_IV,V electron energy-loss spectroscopy. The average valence of the praseodymium ions is close to +3.0 and virtually constant over the sample set when the samples also contained manganese ions. Pr_0.5Sr_0.5InO_3−δ showed a distinct increase in the praseodymium valence state. In contrast, the average valence of the manganese ions changed from the trivalent state to intermediate values between +3.0 and +4.0 and approached the tetravalent state depending on the level of substitution. The knowledge of the valence is required to understand the conduction mechanisms in the material due to the small polaron hopping (electronic conductivity) and motion of oxygen ions along the vacancies (ionic conductivity). Addition of strontium and indium led to the formation of oxygen vacancies. A previously assumed intermediate valence of praseodymium as causal factor for the higher oxygen catalytic activity cannot be confirmed with room temperature measurements.     

Influence of the concentration in Fe-doped BaTiO3 on magnetoelectric couping of layered composites BaTi1−xFexO3–Tb1−yDyyFe2−z

Perovskites BaTi_1−xFe_xO₃ has been synthesized with the concentration x ranging from 0.01 to 0.02. Their transformation point of ferroelectric to paraelectric and the corresponding latent heat of the phase transformation were observed to decrease with increasing the doping level of Fe³⁺. Bonded layered composites BaTi_1−xFe_xO₃–Tb_1−yDy_yFe_2−z have been fabricated and their magnetoelectric effect has been investigated. The sample containing a layer of perovskite BaTi_0.985Fe_0.015O₃ was found to show the maximum transverse ME voltage coefficient, which is about 1422 mV Oe⁻¹ cm⁻¹ under a magnetic field of 1580 Oe, in these bilayers. Analysis shows that the Fe-doped BaTiO₃ with doping level at about 1.5% should have largest piezoelectric coefficient in these ceramics BaTi_1−xFe_xO₃.     

Photoluminescence of Eu-doped CaMgSi2xO6+2x (1.00?x?1.20) phosphors in UV-VUV region

Alkaline-earth silicate phosphors CaMgSi_2xO_6+2x:Eu²⁺ (1.00?x?1.20) were prepared by traditional solid-state reaction. The phosphors showed an intense blue emission centered around 453 nm, with both 254 and 147 nm excitations. The host absorption below 200 nm in the excitation spectra consisted of two bands around 160 and 190 nm. The band around 160 nm was ascertained to be associated with the SiO₄-tetrahedra and MgO₆-polyhedra, and that around 190 nm was due to the CaO₈-polyhedra or some impurities. The incorporation of excess Si of less than 15% would not lead to formation of impurities and the results indicated that an appropriate Si excess could improve the Photoluminescence (PL) intensity in both ultraviolet (UV) and vacuum ultraviolet (VUV) regions     

Glass transition behavior of binary GaxSe100−x (0?x?10) glass systems

The glass transition behavior of glassy Ga_xSe_100−x (x=0, 2.5, 5, 7.5 and 10) systems were investigated using differential scanning calorimetry (DSC). The variation of glass transition temperature, T_g, with Ga concentration has been studied. The value of activation energy of glass transition, E_g, has been found to increase with increase in Ga content. This increase in E_g has been explained in terms of the average heat of atomization for these glasses.     

Structural and magnetic properties in the self-doped perovskite manganites with nominal composition La0.7Sr0.3−xMnO3−δ

Perovskite manganites with nominal composition La_0.7Sr_0.3−xMnO_3−δ (0.00≤x≤0.20) have been prepared by the sol-gel method with the highest heat treatment temperature being 1073 K. The XRD patterns indicate that when the doping level is x≤0.10 the samples have only a single phase, with the R3?c perovskite structure, while for x>0.10, the samples have two phases with the R3?c perovskite being the dominant phase and Mn₃O₄ being the second phase. A quantitative analysis and Rietveld fitting of the X-ray powder diffraction data indicate that on the basis of the thermal equilibrium theory of crystal defects there are Mn²⁺ ions at the A sites and Mn³⁺ plus Mn⁴⁺ ions at the B sites in the ABO₃ perovskite phase. The curves of magnetization versus applied magnetic field at 10 K showed that the magnetic moments of the Mn²⁺ ions at the A sites are antiparallel to those of the Mn³⁺ and Mn⁴⁺ ions at the B sites.