Amine-terminated water-dispersible FePt nanoparticles

Chemically disordered face-centered cubic FePt nanoparticles (NPs) were synthesized via pyrolysis of iron(III)ethoxide and platinum(II)acetylacetonate. The surface ligands of these NPs were then exchanged from oleic acid to 2-aminoethanethiol (AET). The AET-capped FePt NPs were found to be well dispersed in water when pH<8, and the zeta potential was more than +30 mV when pH?7.     

Stability Investigation of Colloidal FePt Nanoparticle Systems by Spectrophotometer Analysis

FePt magnetic nanoparticle systems are an excellent candidate for ultrahigh-density magnetic recording. Monodisperse FePt nanoparticles are synthesized by superhydride reduction of FECl2·4H2O and Pt （acac）2 at 263℃ under N2 atmosphere. Transmission electron microscopy （TEM） images show monosize EePt nanoparticles with diameter of 4 nm and a standard deviation of about 10%. The average distance between monodispesre particles is nearly 3 nm, and oleic acid and oleylamine surround the nanoparticles as surfactants. Stability investigation of nanoparticle colloidal solution is done via speetrophotometery analysis. The results for FePt nanoparticles dispersed in hexane indicate that adding surfactants with concentration of 3 × 10^-3 part by volume for centrifugation stage increases the stability of FePt nanoparticles solution with concentration of 16 mg/mL, about 67%.     

Fabrication of L10 FePtAg nanoparticles and a study of the effect of Ag during the annealing process

L1₀ ferromagnetic phase FePt nanoparticles containing Ag atoms (FePtAg) were synthesized by means of a liquid phase process, followed by annealing. The addition of Ag to FePt nanoparticles permits annealing to be conducted at a lower temperature (350 °C). This is further accompanied by a subsequent transformation in the crystal phase from the FCC superparamagnetic phase to the FCT (L1₀) ferromagnetic phase. The effects of annealing temperature and the Ag atoms inside the nanoparticles on the magnetic properties of the FePt nanoparticles have been studied. Using electron spectroscopy for the chemical analysis (ESCA), Ag atoms in the L1₀ phase FePtAg nanoparticles were found to be localized on the surface region of the annealed nanoparticles. The Ag atoms function to inhibit the oxidation of FePt, causing the particles to become more stable and to have ferromagnetic properties.     

Tailoring the magnetic properties of manganese ferrite with substitution of a small fraction dysprosium for iron

Manganese ferrite nanoparticles with dysprosium (Dy) ions substituted for iron ions have been prepared by using a sol-gel method. Substitution of a small fraction Dy for Fe results in the larger magnetocrystallite anisotropy of MnFe_2−xDy_xO₄ (x=0.2, 0.4) nanoparticles than that of MnFe₂O₄ nanoparticles. The magnetosrystallite anisotropy was enhanced with the increase in the substituted dysprosium content. Combining the result of Mössbauer spectra with ZFC and FC curves, we know clearly that the Dy substitution can modify the anisotropy of MnFe₂O₄ nanoparticles for its strong spin-orbital coupling. Through this simple substitution, we can control the magnetosrystallite anisotropy of the magnetic nanoparticles and make good use of the products according as we need.     

Large coercivity and small exchange bias in Mn3O4 / MnO nanoparticles

Core/shell structured Mn₃O₄/MnO nanoparticles were prepared by arc evaporating metallic manganese in air. These nanoparticles show unconventional exchange bias phenomena, in which the Curie temperature of the ferrimagnetic Mn₃O₄ is lower than the Néel temperature of the antiferromagnetic MnO. The exchange bias field in Mn₃O₄/MnO nanoparticles is much smaller than that in Mn₃O₄/Mn nanoparticles, due to the weak interfacial exchange coupling. The coercivity of the Mn₃O₄ phase in nanoscale is almost three times greater than that of the bulk Mn₃O₄.     

Structural and magnetic features of heterogeneously nucleated Fe-oxide nanoparticles

Iron oxide nanoparticles of diameter 14 nm were synthesized by applying Pt seed-assisted heterogeneous thermal decomposition of Fe(CO)₅ in a two-stage procedure. The intense heating treatment resulted in a remarkable mean volume increment compared to previous studies. This method is able to control the nanoparticle mean diameter, keeping the demand for thermal energy at low levels. High-resolution electron microscopy images and the corresponding electron diffraction patterns revealed the appearance of a FePt₃ core in each nanoparticle, surrounded by highly crystallized inverse spinel Fe₃O₄ formed after atmospheric oxidation, as shown by a combination of X-ray diffraction and chemical analysis. Magnetic measurements indicated that the presence of Pt-rich core does not cause any visible modification to the values of saturation magnetization and anisotropy constant of nanoparticles, compared to homogeneously nucleated iron oxide particles of the same size.     

Interaction and size effects in magnetic nanoparticles

Magnetic nanoparticles dispersed as a ferrofluid with volumetric concentrations in the range 0.4 to 10% and sizes ranging from 59–77 Å have been studied via magnetic measurements at room and low temperatures. Remanence measurements have been used to determine switching and coupling effects. Particle size and concentration effects have been investigated and we find that the samples with higher concentrations have larger coercivities than expected due to coupling effects. Interactions have been found to be demagnetising overall as expected for dipolar interacting systems. Surface effects become evident below 10 K when thermal effects are weak.     

Thermal treatment effects in the self-assembly of FePt nanoparticle arrays

This work concentrates on the influence of synthetic mechanisms of FePt nanoparticles on their self-arrangement and some structural and magnetic properties as studied by means of different electron microscopy techniques and SQUID magnetometry. High-reflux points associated with long boiling durations seem adequate to increase the iron precursor's decomposition yield and facilitate the simultaneous cubic to tetragonal FePt transformation, in single-phase FePt nanoparticles. Nevertheless, such conditions also result in the loss of long-range arrangement and in the appearance of coalescence effects. A core–shell structure comprising of FePt and Fe₃O₄ is favored under mild thermal conditions during synthesis, which seems to confront the undesirable atomic diffusion. Additionally, particle isolation due to the surfactant coating leads in an hcp-symmetry self-assembly. Moreover, working at lower temperatures allows a homogeneous mixture between different phases producing binary composite arrays.     

The colloidal stability and core-shell structure of magnetite nanoparticles coated with alginate

The adsorption of alginate (Alg) onto the surface of in water dispersed Fe₃O₄ nanoparticles and zeta potential of alginate-coated Fe₃O₄ nanoparticles have been investigated to optimize the colloidal stability of Alg-coated Fe₃O₄ nanoparticles. The adsorption amount of Alg increased with the decrease of adsorption pH. The zeta potential of Fe₃O₄ nanoparticles shifted to a lower value after adsorption of Alg. The lower adsorption pH was the lower zeta potential of Fe₃O₄ nanoparticles became. The Alg-coated Fe₃O₄ nanoparticles were found to be stabilized by steric and electrostatic repulsions. Those prepared at pH 6 were not stable around pH 5, and those prepared at pH 4 became unstable at pH below 3.5. Alg of M_w 45 kDa was a little bit more adsorbed onto nanoparticles surface than that of M_w 24 kDa. An average Fe₃O₄ core size of 9.3 ± 1.7 nm was found by transmission electronic microscopy. An average hydrodynamic diameter of 30-150 nm was measured by photon correlation spectroscopy. However, an average core size of 10 nm and an average hydrodynamic diameter of 38 nm were estimated from the magnetization curve of the concentrated magnetic fluids (MFs). The maximum available saturation magnetization of MFs was about 3.5 kA/m.     

Synthesis and magnetic properties of Co–Zn magnetic fluid

Co_1−xZn_xFe₂O₄ (with x varying from 0 to 0.7) nanoparticles to be used for ferrofluid preparation were prepared by chemical co-precipitation method. The fine particles were suitably dispersed in transformer oil using oleic acid as the surfactant. The magnetization (M_s) and the size of the particles were measured at room temperature. The magnetization (M_s) was found to decrease with the increase in zinc substitution. The magnetic particle size (D_m) of the fluid was found to vary from 11.19 to 4.25 nm decreasing with the increase in zinc substitution.     

Investigating the formation and magnetic properties of the Dy0.75Fe1.25O3 orthoferrite prepared by sol-gel method

In this paper, the Dy_0.75Fe_1.25O₃ orthoferrite nanoparticles were synthesized successfully by sol-gel method. Dy_0.75Fe_1.25O₃ orthoferrite nanoparticles are obtained by calcining the flakes at 600 and 700 °C. The magnetic properties of the different samples are investigated using Quantum Design MPMS SQUID magnetometer and MS-500 Mössbauer spectrometer. Magnetic phase γ-Fe₂O₃ coexists in the samples calcined at 600 °C and orthoferrite phase is completely recovered in the samples calcined at 700 °C. Although excessive Fe³⁺ ions were introduced, none of these iron spins couple magnetically with Dy³⁺ ions.     

Comparative study of iron-containing haematinics from the point of view of their magnetic properties

The dynamic magnetic susceptibility of several haematinics in which iron is present as antiferromagnetic salts or iron oxyhydroxide nanoparticles has been measured. Among other parameters, the temperature dependence of the AC susceptibility of each compound acts as a fingerprint that informs about microstructural aspects of the presence of iron. The physicochemical characterisation of these compounds is of great relevance with respect to their bioavailability in the treatment of iron deficiency anaemia.     

Study of polydiethylsiloxane-based ferrofluid with excellent frost resistance property

The polydiethylsiloxane-based ferrofluid was prepared by dispersing finely divided magnetic Fe₃O₄ particles which are modified with oleoyl sarcosine and lauroyl sarcosine. The optimized experiment parameters including molar ratio of surfactant to Fe₃O₄ (1:5), temperature (80 °C), stirring rate (300 RPM), the surfactant content of lauroyl sarcosine (0 to 33 mol%) and the modification time (25 min) were obtained by the orthogonal test. The magnetic liquid was characterized by a transmission electron microscope (TEM), infrared (IR) spectrometer, X-ray diffractometer (XRD), thermogravimetry (TG), vibrating sample magnetometer (VSM) and differential scanning calorimetry (DSC). It is indicated that the surfactant is mainly bonded to the surface of Fe₃O₄ nanoparticles through covalent bond between carboxylate (COO⁻) and Fe atom. The modified magnetic particles are equally dispersed into the carrier and remain stable below −12 °C over 4 months. The ferrofluids exhibit excellent frost resistance property and distinctly reduced temperature coefficient of viscosity compared with polydimethylsiloxane-based ferrofluids and hydrocarbon-based ferrofluids, respectively. The saturation magnetization could reach up to 27.7 emu/g.     

In situ hybridization to chitosan/magnetite nanocomposite induced by the magnetic field

Chitosan/magnetite nanocomposite was synthesized induced by magnetic field via in situ hybridization in ambient condition. Results of XRD patterns and TEM micrographs indicated that magnetite particles with 10–20 nm were dispersed in chitosan homogeneously. An interesting result is that magnetite nanoparticles were assembled to form chain-like structures under the influence of the external magnetic field, which mimics the magnetite chains inside of magnetotatic bacteria. The saturated magnetization (Ms) of nano-magnetite in chitosan was 50.54 emu/g, which is as high as 54% of bulk magnetite. The remanence (Mr) and coercivity (Hc) were 4 emu/g and14.8 Oe, respectively, which indicated that magnetite nanoparticles were superparamagnetic. The key of route is that a pre-precipitated chitosan hydrogel membrane, used as chemical reactor, which controlled the precipitation of chitosan precipitation and in situ transformation of magnetite from the precursor simultaneously in the magnetic field environment.     

Magnetite nanoparticles as-prepared and dispersed in Copaiba oil: study using magnetic measurements and Mössbauer spectroscopy

Study of magnetite nanoparticles, as-prepared and dispersed in Copaiba oil as magnetic fluid, by means of magnetic measurement and Mössbauer spectroscopy at various temperatures demonstrated differences in the saturation magnetization and Mössbauer hyperfine parameters which were related to the interactions of Copaiba oil polar molecules with iron cations on magnetite nanoparticle’s surface.     

Sterically stabilized water based magnetic fluids: Synthesis,structure and properties

Magnetic fluids (MFs), prepared by chemical co-precipitation followed by double layer steric and electrostatic (combined) stabilization of magnetite nanoparticles dispersed in water, are presented. Several combinations of surfactants with different chain lengths (lauric acid (LA), myristic acid (MA), oleic acid (OA) and dodecyl-benzene-sulphonic acid (DBS)) were used, such as LA+LA, MA+MA, LA+DBS, MA+DBS, OA+DBS, OA+OA and DBS+DBS. Static light scattering, transmission electron microscopy, small angle neutron scattering, magnetic and magneto-rheological measurements revealed that MFs with MA+MA or LA+LA biocompatible double layer covered magnetite nanoparticles are the most stable colloidal systems among the investigated samples, and thus suitable for biomedical applications.     

Magnetorheological characteristics of nanoparticle-added carbonyl iron system

Magnetorheological (MR) fluid, suspension of magnetic carbonyl iron (CI) and magnetic additives in mineral oil, were prepared. The novel core–shell structured additives, comprising monodisperse polystyrene (PS) spheres as cores and magnetite as shells, were fabricated by surfactant-free emulsion polymerization. This MR fluid with bimodal particles was suspended in mineral oil and their MR characteristics were examined via a rotational rheometer in a parallel plate geometry equipped with a magnetic field supplier. MR properties of the bimodal MR fluid with magnetic additive exhibit similar magnetic and MR properties compared to MR fluid consisting of pristine CI, but with much improved dispersion stability.     

Exchange bias in a magnetic ordered/disordered nanoparticle system: A Monte Carlo simulation study

We have employed the Monte Carlo (MC) simulation method to gain information on the exchange bias (EB) effect in nanoparticles composed of a ferromagnetic core and a disordered ferrimagnetic shell. The magnetic disorder of the shell affects the EB properties to the extent that they exhibit aging and training effects. The results of our MC simulations are in very good agreement with the experimental findings in a granular system composed of Fe nanoparticles (mean size ∼6 nm) embedded in a Fe oxide matrix confirming that the glassy nature of the shell is responsible for the observed aging and training effects.     

Low-temperature first-order reversal curves and interaction effects on assemblies of iron oxide nanoparticles

We present the synthesis and magnetic properties of high quality uncoated and gold-coated iron oxide magnetic nanoparticles. The structural properties of these nanoparticles are investigated by transmission electron microscopy, UV-visible spectroscopy and X-ray diffraction. Experimental results and theoretical simulations indicate that the synthesized nanoparticles present a very good monodispersity, and well defined size and shape. The coercive field of these particles is identified by low-temperature first-order reversal curves and the results used in order to fit zero-field-cooled magnetization processes with theoretical models. The identification of the parameters in this analysis suggests that the coating process hardly affects the morphology and the overall magnetic properties of the cores inside coated particles.     

Controlled synthesis of monodispersed superparamagnetic nickel ferrite nanoparticles

Nickel ferrite nanoparticles have been prepared through a gentle chemistry route, starting from iron nitrate, nickel nitrate and stearic acid. The nickel ferrite crystalline phase, the particle size and shape, and the homogeneity of the resulting nanoparticles were studied by X-ray diffraction and transmission electron microscopy. Fourier transform infrared techniques were used to study the composition characteristics of the as-prepared sample. Magnetization studies at room temperature showed superparamagnetic behavior for the nanoparticles. Magneto-optic rotation studies at different wavelengths of He-Ne lasers reveal non-linear behavior.