Electromagnetic wave absorption properties of carbonyl iron-ferrite/PMMA composites fabricated by hybridization method

The surface of carbonyl iron powder or a mixture of carbonyl iron and ferrite was coated with polymethylmethacrylate (PMMA) microspheres by a hybridization method to make hybrid powders, and then electromagnetic wave absorption properties of the hybrid composites prepared with these hybrid powders have been investigated. As for the carbonyl iron/PMMA hybrid composite, the reflection loss less than −20 dB could be achieved in a frequency range of 1.7–5.0 GHz when the composite thickness was below 5.00 mm. In the case of the carbonyl iron-ferrite/PMMA hybrid composite, a similar reflection loss was observed in a frequency range of 4.3–13.0 GHz. Thus, the addition of ferrite was found to be useful for achieving a large absorption in a wide frequency range, especially for higher frequency values. Simulated values for the minimum reflection loss are well agreed with actually measured ones, because of homogeneous distribution of carbonyl iron and/or ferrite in these hybrid composites.     

Wave front reversal of surface magnetostatic waves

The wave front reversal (WFR) of non-reciprocal waves has been investigated. The experiment was performed using surface magnetostatic waves (SMSW) excited by a pulsed microwave signal of the carrier frequency ∼4.7 GHz in an epitaxial yttrium–iron garnet (YIG) film. The WFR was realized by pulsed parametric pumping of a double frequency. It was shown that WFR with high efficiency can be achieved for SMSW having relatively small wavenumbers k∼10² rad/cm.     

Fe nanowire encapsulated in boron nitride nanotubes

Boron nitride (BN) nanotubes, nanohorns, nanocoils were synthesized by annealing Fe₄N and B powders at 1000 °C for 1 h in nitrogen gas atmosphere. Especially, Fe-filled BN nanotubes were produced, and investigated by high-resolution electron microscopy, high-angle annular dark-field scanning transmission electron microscopy, electron diffraction and energy dispersive X-ray spectroscopy, which indicates that the [110] of Fe is parallel to the BN nanotube axis. Formation mechanism of Fe-filled BN nanotube was speculated based on these results.     

Microwave-absorbing properties of NiCoZn spinel ferrites

In this paper, the microwave-absorbing properties of (Ni_1−x−yCo_xZn_y)Fe₂O₄ spinel ferrites have been investigated within the frequency range of 0.5–14 GHz. There are two kinds of resonance peaks observed in the permeability spectra: domain-wall resonances at lower frequency and spin-rotation resonances at higher frequency. The reflection loss (RL) calculations show that the prepared NiCoZn spinel ferrites are good electromagnetic (EM) wave absorbers in microwave range. In terms of the absorbing frequency band (AFB) and the matching thickness (t_m), (Ni_0.407Co_0.207Zn_0.386)Fe₂O₄ shows the best performances: t_m=3.15 mm and the AFB is 8.64–11.2 GHz. Decreasing the weight ratio of NiCoZn ferrites in ferrites/wax composites, the matching thickness decreases and the AFB shifts to higher frequencies. Compared with the absorbers with single-layer ferrites, the absorbers with double-layers ferrites have better absorbing performances, such as a thinner matching thickness and a wider EM wave AFB.     

Spin dynamics at low microwave frequencies in crystalline Fe ultrathin film double layers using co-planar transmission lines

Magnetic damping has been studied in magnetic double layers using a network analyzer (NA) with a coplanar transmission line. The magnetic films consisted of ultrathin crystalline films of Fe separated by an Au spacer. The films were deposited on GaAs(0 0 1) substrates using the molecular beam epitaxy (MBE) technique. NA-ferromagnetic resonance (NA-FMR) measurements were carried out along the magnetic hard axis, allowing one to follow the frequency FMR linewidth down to the 1 GHz range of frequencies. It will be shown that the FMR linewidth in the NA-FMR measurements is not entirely described by Gilbert damping. The additional contribution in the frequency linewidth increases with decreasing frequency, and is most likely caused by dipolar fields associated with an inhomogeneous RF field around the coplanar transmission line.     

Adjacent-track interference in ultrahigh-density perpendicular recording system

In perpendicular recording system, the increase of track density is crucial to achieve ultrahigh areal density. At higher track densities, the adjacent-track interference (ATI) arises. In this work, ATI is studied by micromagnetic simulation. Two adjacent tracks are written successively. The track–track distance (TTD) and head–medium spacing are varied to analyze the write and read performance of these two tracks and to investigate the influence of ATI on recording performance. Simulation results indicate that when a track is written first, it is less vulnerable to ATI. ATI is stronger in a track with higher linear recording density. The head–medium spacing plays a significant role in the achievement of low ATI in perpendicular recording system. If the head–medium spacing is reduced to 5 nm, areal recording density above 540 Gb/in² could be realized.     

Design,fabrication and characterization of a Schottky diode on an AlGaAs/GaAs HEMT structure for on-chip RF power detection

A Schottky diode was designed and fabricated on an n-AlGaAs/GaAs high electron mobility transistor (HEMT) structure for RF power detection. The processing steps used in the fabrication were the conventional steps used in standard GaAs processing. Current–voltage measurements showed that the devices had rectifying properties with a barrier height of 0.5289–0.5468 eV. The fabricated Schottky diodes detected RF signals well and their cut-off frequencies up to 20 GHz were estimated in direct injection experiments. To achieve a high cut-off frequency, a smaller Schottky contact area is required. The feasibility of direct integration with the planar dipole antenna via a coplanar waveguide transmission line without insertion of matching circuits was discussed. A higher cut-off frequency can also be achieved by reducing the length of the coplanar waveguide transmission line. These preliminary results represent a breakthrough as regards direct on-chip integration technology, towards the realization of a ubiquitous network society.     

Perpendicular magnetic recording technology at 230 Gbit/in

A perpendicular recording system that allows areal densities beyond 200 Gbit/in² has been designed and tested to investigate the major challenges in perpendicular magnetic recording. The integrated write/read head has a trailing shield to improve the write head field gradient and a conventional CIP–GMR reader. The medium is a low-noise CoPtCr-based oxide medium with a CoTaZr soft underlayer. On track byte error rates at ∼ 50 Mb/s are better than 10⁻⁴ at ∼1000 kbpi. Using a 15% off-track criterion at 10⁻² byte error rate, track densities between 200–240 ktpi are realized, yielding areal densities of 210–233 Gbit/in². High-resolution magnetic force microscopy (hrMFM) has been employed to investigate the write characteristics of these heads with improved cross-track resolution. Using a quantitative analysis method, many parameters, such as transition curvature and transition width, are estimated from the hrMFM image. Significant transition curvature is found, which increases the width of the read head response to a transition, T₅₀, by 2–3 nm.These results give insights into the recording physics of perpendicular recording and in particular point out improvements required for achieving even higher areal densities.     

Mutual phase locking in high-frequency microwave nano-oscillators as a function of field angle

We perform a qualitative analysis of phase locking in a double point-contact spin–valve system by solving the Landau–Lifshitz–Gilbert–Slonzewski equation using a hybrid-finite-element method. We show that the phase-locking behaviour depends on the applied field angle. Starting from a low field angle, the locking-current difference between the current through contact A and B increases with increasing angle up to a maximum of 14 mA at 30°, and it decreases thereafter until it reaches a minimum of 1 mA at 75°. The tunability of the phase-lock frequency with current decreases linearly with increasing out-of-plane angle from 45 to 21 MHz/mA.     

Well-confined Yb:GdVO4 laser waveguide formed by MeV C ion implantation

The planar waveguide in x-cut Yb:GdVO₄ crystal has been fabricated by 6.0 MeV carbon ion implantation with the fluence of 1 × 10¹⁴ ions/cm² at room temperature. The modes of the waveguide were measured by the prism-coupling method with the wavelength of 633 nm and 1539 nm, respectively. An enhanced ordinary refractive index region was formed with a width of about 4.0 μm beneath the sample surface to act as a waveguide structure. By performing a modal analysis on the observed transverse magnetic polarized modes, it was found that all the transverse magnetic polarized modes can be well-confined inside the waveguide. Strong Yb-related photoluminescence in Yb:GdVO₄ waveguide has been observed at room temperature, which reveals that it exhibits possible applications for integrated active photonic devices.     

Broadband GHz frequency characterizations of Permalloy nanorods’ array

The radio frequency characteristics of Permalloy nanorods’ array have been examined by coplanar waveguide (CPW) cell. The Permalloy nanorods’ array was grown in anodic aluminum oxide porous templates with a diameter of 20 nm. As the Permalloy nanorods’ array was placed on CPW, the characteristic impedances of the CPW were changed from 50 to at 1 GHz. The magnitude of inductance was decreased from 3 GHz and the capacitance was increased up to twice in comparison with that of CPW. The signal attenuations were abruptly increased over 1 GHz. The propagation wavelengths due to the insertion of Permalloy nanorods’ array were decreased about 30% at 1 GHz in comparison with that of CPW without magnetic materials.     

Characterization of laser waveguides in Nd:CNGG crystals formed by low fluence carbon ion implantation

We report on Nd:CNGG active planar waveguides produced by 6.0 MeV carbon ion implantation at fluence from 1 × 10¹⁴ ions/cm² to 8 × 10¹⁴ ions/cm². The refractive index profiles, which were reconstructed according to the measured dark mode spectroscopy, showed that the refractive indices had negative changes in the surface region, forming typical barrier waveguide. The width of waveguide structure induced by carbon ion implantation is ∼3.8 μm. The typical barrier-shaped distribution may be mainly due to the nuclear energy deposition of the incident ions into the substrate. By performing a modal analysis on the observed TE modes, it was found that the TE₀ and TE₁ modes can be well-confined inside the waveguide.     

Model design on calculations of microwave permeability and permittivity of Fe/SiO2 particles with core/shell structure

Fe/SiO₂ particles with core/shell structure were prepared by coating silica on the surface of a commercial spherical carbonyl iron via the hydrolysis process of tetraethyl orthosilicate (TEOS). The electromagnetic performance of commercial carbonyl iron and as-prepared Fe/SiO₂ particles was studied theoretically and experimentally. As predicted by the theoretical calculation based on the Bruggeman formula and the Landau–Lifshitz–Gilbert (LLG) theory, the insulating surface layer of silica was effective to reduce the permittivity parameters of pure carbonyl iron. The measured results showed good agreement with the theoretical prediction. Although there was a little decrease in the permeability of the Fe/SiO₂ core/shell particles, a better impedance match especially at higher frequency range was obtained when used as a microwave absorber. The reflection loss (RL) curves show that the lowest reflection loss of Fe/Epoxy composite (−20.5 GHz) was obtained corresponding to the frequency of 8.5 GHz when the thickness of the absorber was 3 mm. A different trend was observed in Fe/SiO₂/Epoxy composite. The reflection loss value got lower by decreasing the thickness of absorbers. At the thickness of 2.2 mm, a relative low reflection loss (−17 GHz) corresponding to the frequency of 13.6 GHz was obtained. Compared with the Fe/Epoxy composite, the improvement on shifting the reflection loss peak to higher frequency and on reducing the optimal thickness of absorbers was made by Fe/SiO₂/Epoxy composite.     

Electrical conductivity and electromagnetic interference shielding characteristics of multiwalled carbon nanotube filled polyacrylate composite films

Multiwalled carbon nanotubes (MWCNTs) were homogeneously dispersed in pure acrylic emulsion by ultrasonication to prepare MWCNT/polyacrylate composites applied on building interior wall for electromagnetic interference (EMI) shielding applications. The structure and surface morphology of the MWCNTs and MWCNT/polyacrylate composites were studied by field emission scanning microscopy (FESEM) and transmission electron microscopy (TEM). The electrical conductivity at room temperature and EMI shielding effectiveness (SE) of the composite films on concrete substrate with different MWCNT loadings were investigated and the measurement of EMI SE was carried out in two different frequency ranges of 100-1000 MHz (radio frequency range) and 8.2-12.4 GHz (X-band). The experimental results show that a low mass concentration of MWCNTs could achieve a high conductivity and the EMI SE of the MWCNT/polyacrylate composite films has a strong dependence on MWCNTs content in both two frequency ranges. The SE is higher in X-band than that in radio frequency range. For the composite films with 10 wt.% MWCNTs, the EMI SE of experiment agrees well with that of theoretical prediction in far field.     

Electromagnetic and microwave absorption properties of Fe3O4 magnetic films plated on hollow glass spheres

Magnetic hollow spheres of low density were prepared by plating Fe₃O₄ magnetic films on hollow glass spheres using ferrite plating. The complex permeability and permittivity of spheres–wax composites were measured in the range of 2–18 GHz. The complex permeability and permittivity increased, and the dielectric and magnetic losses were improved as the volume fraction of the magnetic spheres in the composites increased from 60% to 80%, which also resulted in a great improvement of microwave absorption properties. For composites with volume fraction 80%, its magnetic resonance frequency was at about 13 GHz and it appeared three loss peaks in the calculated reflection loss curves; the bandwidth less than −10 dB was almost 4 GHz which was just in the Ku-band frequencies (12–18 GHz) and a minimum reflection loss of −20 dB was obtained when the thickness was 2.6 mm; the microwave absorbing properties were mainly due to the magnetic loss. The results showed that the magnetic spheres composites were good and light microwave absorbers in the Ku-band frequencies.     

Experimental evaluation of coplanar waveguide discontinuities

Design guidelines for conductor backed coplanar waveguide are reviewed. A range of coplanar waveguide discontinuities for use in a 44 GHz monolithic low noise amplifier and appropriate equivalent circuits are presented. The discontinuities are characterised over the frequency range 30–60 GHz. Details of the fabrication process for the test structures are also given.     

Adjustable microwave absorption properties of flake shaped (Ni0.5Zn0.5)Fe2O4/Co nanocomposites with stress induced orientation

Flake shaped (Ni_0.5Zn_0.5)Fe₂O₄/Co nanocomposites were successfully fabricated by co-precipitating of Ni-Zn ferrite on the surface of cobalt nanoflakes. The electromagnetic characteristics of the samples were studied at the frequency of 0.1–14 GHz. The results showed that the cobalt nanoflakes in compacted nanocomposites were well orientated, and the nanocomposites were characterized with low optimal reflection loss (RL) of −33.8 dB at 11.5 GHz and broad RL bandwidth for <−20 dB in the frequency range of 7.6–12.1 GHz. At the same time, the position of the absorptive band can be adjusted by changing the mass ratio of ferrite to cobalt in the nanocomposites. It is proposed that the excellent microwave absorption properties are related to the combination of strong shape anisotropy of cobalt nanoflakes and adjustable dielectric loss.     

Thermal stability and switching field of hard/soft-stacked perpendicular media

The time dependence of remanence coercivity and thermal stability were investigated for hard/soft-stacked media consisting of a magnetically hard granular layer underneath a very thin soft layer with a large saturation magnetization, M_s. The values of remanence coercivity at measurement times t′=10³ and 10⁻⁵ s (pulse field) were measured, and defined as H_r and H_r^P. The remanence coercivity on the recording time scale, H_r (1 ns), and the energy barrier, ΔE/kT, were evaluated by fitting H_r and H_r^P to Sharrock's equation taking into account the power law variation of the energy barrier, n. The value of H_r (1 ns) for a (Co–Pt)–SiO₂ (9 nm)/Co–SiO₂ (2 nm) stacked medium with an interfacial coupling control layer was about 9 kOe, which was less than half of that of a (Co–Pt)–SiO₂ (9 nm) conventional medium (=21.3 kOe). The value of ΔE/kT for the stacked medium was about 111 (n=0.7), and was not significantly different from the conventional medium. Moreover, no significant difference in the rate of decrease of H_r with increasing temperature was observed between media with and without interlayers. These results indicate that the use of a thin soft layer with high M_s was effective at significantly reducing H_r with no notable change in thermal stability.     

Preparation and recording characteristics of granular-type perpendicular magnetic recording media with thin intermediate layer

Granular-type media with thin Ru intermediate layer were prepared on a highly oriented high-B_s FeCo soft underlayer (SUL). A CoPt–TiO₂ recording layer on a Ru intermediate layer of only 2 nm had high-crystal orientation, high H_c of 6.5 kOe, and a high squareness ratio (SQ) of 0.99. The magnetic property of the SUL was also good. The recording performance was measured for the media with different Ru intermediate thicknesses by using a single-pole-type (SPT) head. The media had large reproduced output even for the Ru intermediate layer thickness of 2 nm.     

Design and recording simulation of 1 Tbit/in patterned media

Design of patterned media for an areal density of 1 Tbit/in² with thermal stability is presented based on perpendicular M–H loops of the media. Required perpendicular magnetic anisotropy was estimated to be achieved with known materials. However, it is indicated that magnetostatic interaction between the dots becomes a limiting factor for achieving higher densities. Recording simulation using a Karlqvist pole head on the designed media exhibited possibility of the recording of 1 Tbit/in². Shift margin of the write head in the cross-track direction was found to be increased with elongated dots in the down-track direction. Recording simulation with an FEM-analyzed field of a side-shielded multi-surface pole head exhibited successful recording with increased cross-track shift margins as well as the effect of the elongated dot shape.